Search Results (185)

Heating, ventilation, and air-conditioning (HVAC) systems account for the largest share of energy consumption in European Union (EU) buildings, representing approximately 40% of the final energy use and contributing significantly to carbon emissions. Latent thermal energy storage (LTES) using phase change materials (PCMs) has emerged as a promising strategy to enhance HVAC efficiency. This review systematically examines the role of latent thermal energy storage using phase change materials (PCMs) in optimizing HVAC performance to align with EU climate targets, including the Energy Performance of Buildings Directive (EPBD) and the Energy Efficiency Directive (EED). By analyzing advancements in PCM-enhanced HVAC systems across residential and commercial sectors, this study identifies critical pathways for reducing energy demand, enhancing grid flexibility, and accelerating the transition to nearly zero-energy buildings (NZEBs). The review categorizes PCM technologies into organic, inorganic, and eutectic systems, evaluating their integration into thermal storage tanks, airside free cooling units, heat pumps, and building envelopes. Empirical data from case studies demonstrate consistent energy savings of 10–30% and peak load reductions of 20–50%, with Mediterranean climates achieving superior cooling load management through paraffin-based PCMs (melting range: 18–28 °C) compared to continental regions. Policy-driven initiatives, such as Germany’s renewable integration mandates for public buildings, are shown to amplify PCM adoption rates by 40% compared to regions lacking regulatory incentives. Despite these benefits, barriers persist, including fragmented EU standards, life cycle cost uncertainties, and insufficient training. This work bridges critical gaps between PCM research and EU policy implementation, offering a roadmap for scalable deployment. By contextualizing technical improvement within regulatory and economic landscapes, the review provides strategic recommendations to achieve the EU’s 2030 emissions reduction targets and 2050 climate neutrality goals. Full article

Lime plaster has historically been a key material in the preservation of architectural heritage in Peru; however, its availability has been restricted by state regulations that limit its production and commercialization. This study evaluates the performance of paints formulated with inorganic pigments extracted from soils in the Cusco valley, combined with natural and synthetic binders, as a sustainable alternative for the protection of heritage buildings in this Andean region characterized by high altitude, wide thermal variations, and high solar radiation. Adhesion, hardness, drying time, and weather resistance tests were conducted according to applicable ASTM standards for architectural coatings. The results show that these formulations exhibit good adhesion to historic surfaces and greater durability against extreme environmental conditions compared to traditional lime plaster. Their potential compatibility with historic substrates and lower environmental impact suggest that these paints represent a viable alternative in sustainable conservation strategies; however, further studies are needed to more accurately characterize the mineralogical composition of the pigments used. Full article

This manuscript provides a structural analysis of over eighty copper(I) compounds mostly reported in the Cambridge Structural Database (CSD) version 5.45 in which unidentate ligands build up various inner coordinate spheres. These complexes crystallized in four crystal classes: trigonal (1 example), triclinic (10 examples), orthorhombic (13 examples), and monoclinic (58 examples). The analyzed complexes can be divided into two groups according to the type of coordinating ligands (L = X, Y, Z) incorporated into their structure: Cu(XXY) (more common) and Cu(XYZ). The structural data of L-Cu-L bond angles show that the angular distortion from the regular trigonal geometry grows with total mean values of deviation from 120.0°, in the order within the first group: 3.2°(Cu(IIP)) < 6.1°(Cu(ClClY)) < 6.5°(Cu(SSY)) < 8.2°(Cu(PPY)) < 8.9°(Cu(BrBrY)) < 16.9°(Cu(NNY)) < 19.8°(Cu(CCY)) < 25.5°(Cu(SeSeY)) and within the second group: 3.1°(Cu(SIP)) < 14.3°(Cu(SClP) < 15.5°(Cu(SBrP). The donor atoms are responsible for the distortion as follows: the soft donor atoms diminish the distortion while the borderline and the hard growing amplify the distortion. Given the importance of Cu(I) compounds in (bio)inorganic functional materials and catalysis, the correct interpretation of the geometry of Cu(I) complexes in terms of the coordination polyhedra is crucial for understanding the properties of the respective compounds. Full article

Geopolymer concretes, synthesized from industrial by-products such as fly ash through alkaline activation, have attracted considerable attention due to their favorable thermal and microstructural properties. Incorporating phase change materials (PCMs) into geopolymer matrices can improve thermal properties, making them suitable for various sustainable construction applications. The thermal properties of geopolymer concrete depend on the composition and structure of the materials used. Adding PCMs to geopolymer concrete can significantly improve its thermal properties by increasing its heat storage capacity. PCMs absorb and release thermal energy during phase transformations, which can help regulate temperature fluctuations in building materials. This feature is particularly beneficial in regions with extreme temperature fluctuations, where maintaining a stable indoor climate is crucial. Integrating organic PCMs into geopolymer matrices has been shown to improve thermal insulation. Furthermore, the microstructural analysis of geopolymer concrete containing organic PCM indicates that incorporating these materials can lead to a more homogeneous and denser microstructure. Integrating organic PCMs instead of inorganic into geopolymer concrete is a promising route to improve thermal properties and microstructural stability. The combination of geopolymer technology with PCM not only contributes to the sustainable development of building materials but also addresses the challenges of temperature regulation in buildings. Full article

Earthen construction is one of the earliest and most ubiquitous forms of building. Compressed stabilized earth blocks (CSEBs) combine compressed components including inorganic soil, water, and a stabilizer such as Portland cement, and can achieve greater strength than other earthen construction methods. Typically, site-specific soil comprises the bulk material in CSEB construction, which minimizes the quantity of construction materials that need to be provided from off-site and motivates this type of building material for remote locations. However, onsite manufacturing and innate soil variability increase the variability of CSEB mechanical properties compared to more standardized building materials. This study characterizes the effects of varying mix compositions and initial compressions on the density, compressive strength, and variability of compressed stabilized earth cylinders (CSECs) created from sandy soil. CSEC samples comprising nine mix compositions and four levels of initial compression provide data for the (i) statistical evaluation of strength, density, and variability and (ii) development of predictive equations for density and compressive strength, with R² values of 0.90 and 0.89, respectively. Full article

Bamboo is a fast-growing biomass material with excellent performance, making it a preferred choice for the development of green and low-carbon building materials. However, challenges such as combustibility and difficulties in processing and utilization persist. In this study, bamboo chips are wrapped in fiberglass cloth and cemented with magnesium oxychloride cement (MOC) to develop green, environmentally friendly, flame-retardant, and carbon-storing bamboo-based composite panels. Firstly, the optimal ratio of the inorganic adhesive MOC was systematically investigated, and flue gas desulfurization gypsum (FG) was added to enhance its water resistance. The flexural strengths of the composite board in the direction of the bamboo fiber and that perpendicular to it were found to be 15.71 MPa and 34.64 MPa, respectively. Secondly, numerical simulations were conducted alongside plate experiments, analyzing the floor and wall made from the boards. The results indicate that since the fiber-reinforced bamboo board as a lightweight wall can meet the requirements for a two-story building, it does not satisfy safety standards as a floor slab due to the higher loads. Despite this limitation, the fiber-reinforced bamboo board shows promising application prospects as a green and low-carbon alternative. Full article

In recent years, bipolar organic electrode materials have gained recognition as competitive alternatives to inorganic materials due to their unique multielectron redox mechanism for energy storage. In this study, we examined the mechanism of redox reactions in naphthalimide (NI) derivatives when used as electrodes in lithium half-cells with ionic liquid electrolytes. The NI derivatives consist of three building fragments: an aromatic naphthalene core, N-alkylated imide unit, and a peri-dichalcogenide bridge. The integration of electrochemical and microscopic methods with DFT calculations facilitates the delineation of the role of each fragment in the oxidation and reduction reactions of NI derivatives. It is found that the peri-dichalcogenide bridge is mainly involved in the oxidation of NI derivatives above 3.9 V, the charge compensation being achieved by electrolyte TFSI⁻ counter-ions. The reduction of NI derivatives with two Li⁺ ions is mainly due to the participation of the chalcogenide bridge, while after interaction with the next two Li⁺ ions, the imide fragment and the naphthalene moiety contribute equally to the reduction. Based on the leading role of the peri-dichalcogenide bridge, the redox properties of NI derivatives are effectively controlled by the gradual replacement of S with Se and Te atoms in the bridge. To improve the electronic conductivity of NIs, composites with rGO are also synthesized by a simple procedure of mechanical mixing in a centrifugal mixer. The composites rGO/NIs display a good storage performance, the best being the Se-containing analogue. Full article

Fire is a combustion reaction where fuel reacts with oxygen in the presence of heat, releasing energy as light, heat, and flames. The main components of fire are fuel, oxygen, and heat. All three components must be present to cause a fire. Fire is a significant threat to residential and commercial buildings, often intensified by high fuel content in building materials such as wood and synthetics. This paper summarizes fire types and damages, loss of property and life, fuel content in building materials, and a method to reduce fire risk by minimizing the building material’s fuel content. This method uses minerals (coal combustion residual (CCR)), primarily inorganic oxides bonded with a small percentage of polyurethane binder, to manufacture a composite material moldable into multiple building products. The composite was tested as per the ASTM for mechanical, thermal, and fire safety performance. ASTM D635-based fire testing showed self-extinguishing behavior with significantly reduced burn rate and lengths (1–2 mm). A low calorific value of 6.6 MJ/kg was determined separately. The test results demonstrate that CCR-based mineral composites offer a fire-resistant, structurally sound, and eco-friendly alternative to wood products. This research supports recycling inorganic minerals into fire-resistant building products that enhance safety. Full article

In recent years, the increasing frequency of building fires has highlighted the limitations of traditional polymeric materials due to their inadequate fireproof performance. Ceramifiable polymer composites have emerged as a promising alternative by incorporating ceramic-forming fillers that create rigid ceramic-like structures through high-temperature eutectic reactions, offering exceptional thermal insulation and fireproof properties. These composites maintain structural integrity under fire exposure through sufficient mechanical strength retention. The effects of several ceramifiable inorganic fillers (CIFs) on the properties of polydimethylsiloxane (PDMS) foams were systematically investigated in this study. The research demonstrated that fillers with better matrix compatibility significantly enhance the foaming quality, mechanical performance, and fireproof capabilities. Notably, the CaCO₃-filled PDMS foam composite (CPF-Ca) demonstrates exceptional foaming characteristics with 84% porosity and a remarkably low density of 0.36 g/cm³. The material achieves tensile and compressive strengths of 0.22 MPa and 0.84 MPa, representing 22% and 127% enhancements, respectively, compared to pure PDMS foam (PPF). Regarding the ceramic conversion capability, the sintered residue of CPF-Ca maintains a compressive strength of 4.39 MPa under high-temperature conditions. This composite material exhibited superior fireproof performance, successfully withstanding a butane torch for 300 s without penetration while maintaining a remarkably low backside temperature of merely 83.6 °C. Full article

The world is facing the issue of managing a huge amount of plastic waste. To prevent uncontrolled and unproductive disposal, various valorization strategies have been developed. Recycling plastic waste into valuable composites for construction offers a promising pathway toward sustainable waste management. Given that the construction industry is a major consumer of energy and natural resources, it presents a key opportunity for integrating recycled materials. This review examines diverse strategies and applications for plastic waste recycling, with a particular focus on sustainable construction solutions, while also evaluating the advantages and limitations of this approach. Within this context, recycled plastic waste can be used as a filler to replace non-renewable natural resources. Studies have shown that incorporating plastic waste as a filler improves diverse properties of composites, including thermal and sound insulation. In particular, thermoset plastic waste exhibits desirable characteristics such as rigidity, heat and chemical resistance, strength and durability, making it suitable as a filler for non-structural applications. Alternatively, melting recycled plastic waste can produce binder materials that combine with other inorganic materials to form building and construction composites. Using melted thermoplastic waste as a binder enhances ductility, reduces water absorption, and improves overall durability. Additionally, the hot-pressing technique has been shown to be more effective in addressing poor bonding issues commonly encountered with conventional methods. Full article

Of all the construction waste, the building interior decoration and renovation waste (D&R waste) is difficult to dispose of and recycle due to its complex components and varied producers. The goal of this study is to reveal the current situation of D&R waste disposal through case studies and put forward the correlation proposal to improve standards of D&R waste recycling. This study investigated the various stages of the D&R waste management process, including generation, collection, transportation, sorting, recycling, and landfilling. Detailed studies were conducted for (i) the composition of D&R waste and (ii) the material flow analysis (MFA) of D&R waste recycling in different cases with different sorting technology. The results show that (i) concrete, stone, and other hard inorganic materials accounted for about 35–55% of the total. Soft inorganic materials such as aerated concrete and gypsum made up 5–25%, slag 15–20%, timber 5–10%, combustible matter such as plastic, rubber, and paper 9–12%, and glass and metal 1–5%, and (ii) artificial intelligence (AI) sorting offers better sorting performance and economic advantages over manual sorting, promoting the application of artificial AI sorting equipment as important solutions to face the key challenges of D&R waste recycling. Full article

A novel organic–inorganic eutectic phase change material (PCM) based on sodium acetate trihydrate (SAT) and polyethylene glycol (PEG) was developed to meet the needs of heat recovery and building heating. Three kinds of PEG with different molecular weights were selected to form organic–inorganic eutectic PCM with SAT. The thermal properties of three series of SAT-PEG eutectic PCM were compared based on DSC results, focusing on the impact of PEG addition on the phase change temperature and enthalpy of SAT, as well as the melting uniformity. The inhibitory effects of two nucleating agents on the supercooling of SAT-PEG eutectic PCM were systematically investigated. The effect of PEG on the crystallization behavior of SAT was studied using a metallographic microscope. To evaluate the thermal reliability of the SAT-PEG eutectic PCM, 600 cycles of melting–solidification experiments were conducted. Experimental results show that SAT can form eutectic PCMs with PEG200, PEG600, and PEG6000, respectively, with high enthalpy and excellent melting uniformity. The phase change temperature ranged from 55 °C to 60 °C and the enthalpy was as high as 250–280 kJ/kg. The results of the cooling curves show that 10 wt% tetrasodium pyrophosphate decahydrate (TPD) can reduce the supercooling degree to less than 1 °C. Significantly, all three series of SAT-PEG eutectic PCMs exhibit exceptional thermal reliability after 600 cycles of melting–solidification, with shifts in the phase change temperatures and enthalpies of less than 4%. XRD diffraction patterns showed that SAT, PEG, and TPD were physically mixed without a chemical reaction to form new substances. Microscopic images reveal that the addition of PEG preserves the original needle-shaped crystal morphology of SAT while reducing its crystal size. The rapid formation of small crystals can provide more nucleation points and expedite crystallization, thereby enhancing the heat release capabilities of the PCM. Full article

A geopolymer is a low-carbon cementitious material, and its condensation process is akin to the formation of inorganic polymers. The crystal phase of synthesized geopolymers was identified using XRD; the scattering peaks of amorphous phases were analyzed, and the zeolite minerals akin to different n(Si)/n(Al) geopolymers were determined. Based on this, a model structure of N-A-S-H geopolymers was established. The molecular dynamics structure of the model was simulated, and the density, energy, and bulk modulus of the model were calculated using three different force fields. According to the calculation results, the most suitable force field for N-A-S-H calculation is COMPASS III. In this study, all calculations were performed using MaterialsStudio 7.0. The research process introduces a new modeling method for geopolymers, similar to building C-S-H based on Tobermorite, which aids in advancing the molecular dynamics simulation of geopolymers. Full article

Advances in nanotechnology have made it possible to observe and evaluate structures down to the atomic and molecular level. The next step in the development of functional materials is to apply the knowledge of nanotechnology to materials sciences. This is the role of nanoarchitectonics, which is a concept of post-nanotechnology. Nanoarchitectonics is defined as a methodology to create functional materials using nanounits such as atoms, molecules, and nanomaterials as building blocks. Nanoarchitectonics is very general and is not limited to materials or applications, and thus nanoarchitecture is applied in many fields. In particular, in the evolution from nanotechnology to nanoarchitecture, it is useful to consider the contribution of nanoarchitecture in device applications. There may be a solution to the widely recognized problem of integrating top-down and bottom-up approaches in the design of functional systems. With this in mind, this review discusses examples of nanoarchitectonics in developments of advanced devices. Some recent examples are introduced through broadly dividing them into organic molecular nanoarchitectonics and inorganic materials nanoarchitectonics. Examples of organic molecular nanoarchitecture include a variety of control structural elements, such as π-conjugated structures, chemical structures of complex ligands, steric hindrance effects, molecular stacking, isomerization and color changes due to external stimuli, selective control of redox reactions, and doping control of organic semiconductors by electron transfer reactions. Supramolecular chemical processes such as association and intercalation of organic molecules are also important in controlling device properties. The nanoarchitectonics of inorganic materials often allows for control of size, dimension, and shape, and their associated physical properties can also be controlled. In addition, there are specific groups of materials that are suitable for practical use, such as nanoparticles and graphene. Therefore, nanoarchitecture of inorganic materials also has a more practical aspect. Based on these aspects, this review finally considers the future of materials nanoarchitectonics for further advanced devices. Full article

Hierapolis of Phrygia, an archaeological site in southwestern Turkey, has been a UNESCO World Heritage Site since 1988. During archaeological campaigns, 71 mortar samples from public buildings were collected, dating from the Julio-Claudian to the Middle Byzantine period. The samples were analyzed using a multi-analytical approach including polarized optical microscopy (POM), digital image analysis (DIA), X-ray powder diffraction (XRPD) and SEM–EDS to trace the raw materials and understand the evolution of mortar composition and technology over time. During the Roman period, travertine and marble were commonly used in binder production, while marble dominated in the Byzantine period. The aggregates come mainly from sands of the Lycian Nappe and Menderes Massif, with carbonate and silicate rock fragments. Variations in composition, average size and circularity suggest changes in raw material sources in both Roman and Byzantine periods. Cocciopesto mortar was used in water-related structures from the Flavian to the Severan period, but, in the Byzantine period, it also appeared in non-hydraulic contexts. Straw became a common organic additive in Byzantine renders, marking a shift from the exclusively inorganic aggregates of Roman renders. This study illustrates the evolving construction technologies and material sources used throughout the city’s history. Full article