Search Results (132)

Organic acids could act as retarders in magnesium oxysulfide (MOS) systems, not only delaying setting and improving fluidity but also enhancing compressive strength and water resistance. These effects are generally attributed to both the presence of H⁺ ions and anion chelation. However, the enhancement efficiency of different organic acids in MOS systems varies significantly due to differences in their molecular structures. To determine the underlying mechanism, this study comparatively investigated the effects of amino trimethylene phosphonic acid (ATMP) and tartaric acid (TA) on the setting time, fluidity, compressive strength, and water resistance of the MOS system, with the two additives incorporated at mole ratios to MgO ranging from 0.002 to 0.006. The mechanism behind it was revealed by discussion on the hydration heat, hydrates, and pH value. Results showed that both ATMP and TA could effectively improve the fluidity, delay the setting process, and enhance the mechanical properties, including strength and water resistance. At a mole ratio of 0.006, the incorporation of ATMP increased the 28 d compressive strength and the softening coefficient by 214.12% and 37.29%, respectively, compared with the blank group. In contrast, under the same dosage, TA led to an increase of 55.13% in the 28 d strength and 22.03% in the softening coefficient. Furthermore, hydration heat, product analysis, and pH measurements indicated that both ATMP and TA inhibited hydration during the initial hours but promoted hydration at later stages. The potential reason could be divided into two aspects: (1) H⁺ ions from ATMP and TA suppressing the formation of Mg(OH)₂; (2) anion chelation with Mg²⁺ in the liquid phase, leading to a supersaturated solution with higher saturation, which further hindered Mg(OH)₂ formation and facilitated the later development of 5Mg(OH)₂·MgSO₄·7H₂O (517 phase). By contrast, under the same mole dosage of H⁺ or anions, the enhancement in compressive strength as well as the water resistance is superior when using ATMP. This was owing to its stronger chelating ability of ATMP, which more effectively inhibited Mg(OH)₂ formation and then promoted the formation of the 517 phase. These findings confirm that the chelating ability of anions exerts an important impact on the retarding effect as well as the enhancement of strength in MOS systems. Full article

Water pollution is a global problem that severely impacts human and environmental health, water recycling, and the economy. In Mexico, due to water scarcity, potable water contains significant amounts of heavy metals (i.e., arsenic (As)); thus, there is a need for efficient and sustainable water treatment strategies. Bismuth oxyhalides, BiOX (X = Cl, Br, I), exhibit three-dimensional (3D) porous structures suitable for efficient adsorption activity. In addition, bismuth is an abundant and biocompatible element appropriate for fabricating sustainable environmental remediation technologies, such as adsorptive BiOX nanomaterials (NMs). In this study, we examine the adsorption capacity of BiOX (X = Cl, I), BiOX-GO (GO: graphene oxide) and GO NMs to remove methylene blue (MB), methyl orange (MO) and arsenite (AsO₃³⁻) from aqueous solution. BiOCl-GO 10%, BiOI, BiOI-GO 1%, BiOI-GO 10% and GO have an enhanced adsorption capacity, removing MB (20 ppm) within one hour using a low dose of NMs (1 mg/mL). In addition, BiOX-GO NMs can be easily separated from the solution and regenerated upon visible light activation due to the photocatalytic activity of the materials. The efficiency of the NMs under study for MO removal decreases, with the GO material having the highest efficiency (96%), followed by BiOX-GO 10% (78%). BiOCl-GO 1% removes arsenic from aqueous solution at low doses and short treatment times; 5 mg As/g adsorbent takes five hours; however, at longer adsorption times (24 h), BiOI-GO 1% excels in its arsenic removal capacity. Perlite-supported BiOCl NMs exhibit a weak capacity for water treatment due to the poor mechanical strength of perlite and the amount of surface-exposed BiOCl material. For the photocatalytic removal of arsenic (oxidation–adsorption), BiOI-GO 1% excels in arsenic removal with efficiencies > 70%. Full article

Research on energy demand is advancing, with the addition of nanomaterials in anaerobic digestion increasing stability, accelerating hydrolysis, and reducing microbial inhibition. However, further research is needed to determine the mechanisms, ideal dosages, and long-term impacts. This work used continuous stir tank reactors (CSTRs) to experimentally examine the biocompatibility of iron oxide nanoparticles (Fe₃O₄-NPs) at a concentration of 75 mg/L at various organic loading rates (OLRs) of 0.3, 0.8, and 1.3 gVS/L.d (CSTRs). The efficiency of the reactors was observed by considering various parameters, such as pH, soluble chemical oxygen demand (sCOD), TVFA formation and degradation, total solids (TS), and volatile solids (VS) removal, as well as methane (CH₄) generation. Hence, it was found that the reactor with added NPs (R1) yielded an optimum 725.9 mL/gVS of CH₄ and this was achieved at the lowest OLR of 0.3 gVS/Ld. However, another reactor (R2, without NPs), exhibited more stabilized results, ranging from 372.8 to 424.4 mL/gVS at 0.3 to 1.3 gVS/Ld of OLR, respectively. Therefore, in R1, the maximum removal of sCOD, TVFAs, and VS was achieved at 90%, 74%, and 93%, respectively, as compared to R2. Full article

This study investigates the degradation characteristics of turbocharger nozzle rings in marine diesel engines by conducting numerical analysis and solid particle erosion (SPE) tests to examine their structural stability and morphological surface damage trends. The fatigue analysis was conducted under a load condition corresponding to 100% output of the main engine, using ANSYS software. The SPE test was conducted in accordance with ASTM G76-05 standards, and the weight loss and erosion rate were calculated. Surface damage was closely examined through 3D analysis and scanning electron microscopy (SEM). The flow analysis revealed that the loads were highly concentrated at the nozzle ring inlet and the leading edge of the blades, with a maximum pressure coefficient of 0.07678 MPa. The load decreased toward the trailing edge of the nozzle ring, and the surface pressure coefficients of the flange, inner hoop, and outer hoop—where the nozzle ring blades are fixed—were found to be nearly identical. The fatigue life of the nozzle ring under 100% engine load was calculated as 1.377e⁺⁷ cycles, with a fatigue damage value of 1.32e⁺³². Notably, the fatigue life in the regions near the inner and outer hoops of the nozzle ring approached zero. The results of the SPE test using spherical SiO₂ particles confirmed that the surface damage of the nozzle ring material, 316L stainless steel, followed a typical ductile material damage mechanism. In addition, the surface damage characteristics were significantly influenced by SPE test parameters such as the shape of solid particles, nozzle diameter, and impact angle. Full article

In the context of agricultural green transformation, the balance between the environmental footprint and economic return is a key indicator for measuring the synergy of high yields, high efficiency, and environmental friendliness in agricultural systems. However, the pathways and mechanisms for achieving this synergy in orchard systems remain unclear. Based on a three-year field experiment in Pinghe County, Fujian Province, a comprehensive evaluation framework integrating life cycle assessment (LCA) was constructed. This framework was used to systematically analyze the differences in the net ecosystem economic benefit (EEB) and environmental impact of four fertilization regimes: the conventional farming regime with no mulching (A; 1084 kg N ha⁻¹, 914 kg P₂O₅ ha⁻¹, and 906 kg K₂O ha⁻¹), the conventional farming regime with mulching (B), the optimized fertilization regime with water–fertilizer integration (C; 250 kg N ha⁻¹, 200 kg K₂O ha⁻¹, 100 kg MgO ha⁻¹, and 400 kg CaO ha⁻¹), and the optimized fertilization regime with controlled-release fertilizers (D). The results showed that regime D performed best in terms of yield, nutrient-use efficiency, and EEB, which increased by 220.5% and 297.5% compared with regime A, and reduced the input cost by CNY 63,100~69,000 hm⁻². Moreover, compared with regime A, regimes B, C, and D significantly reduced the carbon, nitrogen, and phosphorus footprints, respectively, with the carbon footprint reduced by 6.7~21.7%, 72.4~74.8%, and 71.6~76.5%; the nitrogen footprint reduced by 2.6~19.0%, 80.7~82.2%, and 80.1~83.4%; and the phosphorus footprint reduced by 15.3%, 100%, and 100%. Furthermore, the comprehensive evaluation index (CEI) is D > C > B > A. In total, the three optimized regimes balanced high yield with environmental sustainability, with the D regime showing the best performance, offering scientific support for transitioning to low-carbon, high-value orchards in smallholder systems. Full article

The safety concerns associated with sensitivity issues regarding long nitrogen chain-based energetic compounds, especially for eight or more catenated nitrogen atoms in backbones, need to be resolved. Incorporating specific functional groups represents a key approach for enhancing stability in organic energetic materials. This study reports the synthesis of 1,1′-(diazene-1,2-diyl)bis(4-nitro-1H-1,2,3-triazole-5-carboxamide) (S8), an N8-chain compound featuring strategically placed amide groups. Employing THA(O-tosylhydroxylamine) and KMnO₄, 1,1′-(diazene-1,2-diyl)bis(4-nitro-1H-1,2,3-triazole-5-carboxamide) (S8) was synthesized and underwent N-amination and oxidative azo coupling. Comprehensive characterization, including X-ray diffraction, mechanical sensitivity testing, and theoretical analysis, alongside comparative studies with known N8 compounds, revealed that S8 exhibits unprecedented stability within its class. Among reported N8-catenated nitrogen chain compounds, attributed to the incorporation of the amide functionality, S8 demonstrates the highest impact sensitivity (IS = 10 J) and friction sensitivity (FS = 40 N) while maintaining excellent detonation performance (D = 8317 ms⁻¹, P = 28.27 GPa). This work highlights the amide group as a critical structural part for achieving high stability in sensitive long-nitrogen-chain energetic materials without compromising performance. Full article

The widespread availability and pseudo-persistence of typical psychiatric pharmaceuticals (PDs) can have serious impacts on aquatic ecosystems and even human health. However, the toxicokinetics of typical PDs and the corresponding enzymatic biomarker responses are unclear. In this study, eight typical PDs [carbamazepine (CBZ), citalopram (CIT), sertraline (SER), venlafaxine (VLF), amitriptyline (AMT), chlorpromazine (CPM), quetiapine (QTP) and clozapine (CLZ)] were selected to study the uptake, depuration and biological effects of PDs in Daphnia magna. The results found that the uptake rates (K_u) were in the sequence of VLF < QTP < CBZ < CLZ < CIT < AMT < SER < CPM, while the depuration rates (K_d) were in the order of CLZ < AMT < CIT < SER < QTP < CBZ < CPM < VLF. Correspondingly, the bioconcentration factors (BCFs) followed on as VLF < QTP < CBZ < CIT < AMT < CLZ < SER < CPM. Both pH-dependent octanol–water partition coefficients (log D_ow) and liposome–water partition coefficients (log D_lip-w) exhibited positive correlations with the log BCF of PDs (p < 0.05), indicating the important roles of ionization degree and biological phospholipid contents on bioconcentration. Superoxide dismutase (SOD) activities were evidently induced in the SER and CPM groups, while ethoxyresorufin-O-deethylase (EROD) and glutathione-S-transferase (GST) activities were significantly induced only in the CBZ group. Acetylcholinesterase (AChE) activity was obviously induced by CBZ, SER and AMT, with levels 1.73, 1.62 and 2.44 times that of the control group (p < 0.05). The K_u of PDs, oxidative stress and metabolic level of D. magna combine to affect BCF levels together. In conclusion, this study contributes to a better understanding of the toxicokinetics and biochemical responses of PDs in D. magna and potential mechanisms of action, which may allow for a better assessment of their environmental health risks to aquatic ecosystems. Full article

Copper-thiolate nanostructures, formed through the self-assembly of cysteine (Cys) and glutathione (GSH) with copper ions, offer a versatile platform for redox-active applications due to their structural stability and chemical functionality. In this study, Cu-Cys-GSH nanoparticles were synthesized and employed to develop a capacitive biosensor for the ultralow concentration detection of hydrogen peroxide (H₂O₂). The detection mechanism leverages a Fenton-like reaction, where H₂O₂ interacts with Cu-Cys-GSH nanoparticles to generate hydroxyl radicals (·OH) through redox cycling between Cu²⁺ and Cu⁺ ions. These redox processes induce changes in the sensor’s surface charge and dielectric properties, enabling highly sensitive capacitive sensing at gold interdigitated electrodes (IDEs). The influence of chirality on sensing performance was investigated by synthesizing nanoparticles with both L- and D-cysteine enantiomers. Comparative analysis revealed that the stereochemistry of cysteine impacts the catalytic activity and sensor response, with Cu-L-Cys-GSH nanoparticles exhibiting superior performance. Specifically, the biosensor achieved a linear detection range from 1.0 fM to 1.0 pM and demonstrated an ultra-sensitive detection limit of 21.8 aM, outperforming many existing methods for H₂O₂ detection. The sensor’s practical performance was further validated using milk and saliva samples, yielding high recovery rates and confirming its robustness and accuracy for real-world applications. This study offers a disposable, low-cost sensing platform compatible with sustainable healthcare practices and facilitates easy integration into point-of-care diagnostic systems. Full article

Carbon–Kevlar hybrid composites are being increasingly recognized as suitable materials for aerospace, automotive, and construction applications due to their unique combination of strength, toughness, and safety. Prior to their use, extensive testing and validation are essential to ensure that these composites meet the specific safety and performance standards required by each industry. In this study, the mechanical performance and behavior of five different types of Carbon–Kevlar hybrid composites were investigated. In addition to microstructural investigations, mechanical tests were also carried out, including tensile, bending, impact, and micro-hardness tests. The investigated composites were Carbon–Kevlar hybrids without orientation, with a symmetrical orientation, and with the addition of TiO₂ nanoparticles at weight percentages of 3%, 4%, and 5%. The results showed that the mechanical properties of these composites could be significantly influenced by different fiber orientations and the addition of TiO₂ nanoparticles. In particular, the addition of TiO₂ nanoparticles increased the tensile strength, hardness, toughness, and breaking strength. Of the composites tested, the composite reinforced with 5% TiO₂ nanoparticles exhibited the highest mechanical performance, with a 79.8 Shore D hardness, 406 MPa tensile strength, 398 N/mm² flexural strength, and 10.1 J impact energy. These results indicate that Carbon–Kevlar hybrid composites reinforced with TiO₂ nanoparticles have excellent mechanical properties that make them highly suitable for armor plating, helmets, and vehicle armoring in particular and a wide range of other industrial applications in general. Full article

Previous research on cement aging mainly focuses on construction cement, exploring the mechanisms through which aging conditions affect cement properties. However, the impact of aging on oil well cement remains understudied. Aging of cement under high-humidity conditions leads to significant alterations in its properties, indicating that the cement formulation needs to be adjusted to reduce the negative effects during cementing operations. The effect of aging on particle size, mineral composition, and early hydration behavior of oil well cement after 0, 7, 14, and 28 d at 90% relative humidity (±3%RH) and 25 °C (±2 °C) was investigated. The results showed that, during the aging process, the uptake of H₂O and CO₂ from the surrounding atmosphere by cement leads to slight hydration. This process was associated with a reduction in the specific surface area and surface energy. The contents of hydration products ettringite (AFt) and calcium hydroxide (CH) increased, whereas the amounts of C₃S and C₃A decreased. Consequently, the early hydration rate of cement decreased along with a reduction in the cumulative heat release. As the aging time increased, the compressive strength and thickening time of the cement pastes decreased, and the rheological properties deteriorated. Under the experimental temperature and humidity conditions, the permissible aging time without significant deterioration should not exceed 7 d, with a maximum permissible aging time of 14 d. Full article

Oxidative stress is a significant factor affecting reproductive efficiency in dairy cows, contributing to conditions such as endometritis that impair fertility and milk production. This study investigates the molecular mechanisms by which bta-let-7d modulates the oxidative stress responses induced by potassium permanganate (KMnO₄) in bovine endometrial epithelial cells (BEECs). Using KMnO₄ to induce oxidative stress, we observed significant increases in reactive oxygen species (ROS) and malondialdehyde (MDA) levels, accompanied by decreased activities of the antioxidant enzymes glutathione peroxidase (GPx) and superoxide dismutase (SOD). Quantitative PCR and Western blot analyses indicated a negative correlation between IGF1R and bta-let-7d expression in oxidative-stress-affected tissues, suggesting opposing roles in managing stress responses. Following KMnO₄ treatment, there was marked downregulation of anti-apoptotic genes and an upregulation of pro-apoptotic markers, alongside diminished antioxidant capacity. Mechanistically, bta-let-7d targets IGF1R, leading to the suppression of the PI3K/AKT signaling pathway and exacerbating oxidative damage. In vivo experiments further confirmed the impact of KMnO₄ exposure on IGF1R expression. These findings provide novel insights into the mechanisms by which KMnO₄ induces oxidative stress and apoptosis in bovine uterus. They highlight the potential for therapeutic strategies targeting the bta-let-7d/IGF1R axis to enhance reproductive health management in dairy cows, offering a promising avenue for mitigating oxidative-stress-related reproductive disorders. Full article

High-fat diets (HFDs) usually trigger disruptions in lipid metabolic processes and immune suppression in fish. As an eco-friendly and potent additive, the inclusion of probiotics in fish diets ameliorates dysregulations in lipid metabolism, mitigates oxidative stress, and reduces inflammatory reactions triggered by HFDs. However, little current research has focused on the improvement of the hazards of HFDs in fish by probiotics. Therefore, we employed 4-dimensional data-independent (4D-DIA) proteomic analysis to investigate the mechanism of the protective impact of probiotics against HFD-induced hepatic injury in Coilia nasus between the HFD group and the probiotic supplementation in HFD (PHFD) group. Additionally, lipid accumulation and antioxidant indicators in the liver were also measured via Oil Red O staining and activity detection. Administration of probiotics markedly attenuated the hepatic concentrations of triglycerides (TG), cholesterol (CHO), and low-density lipoprotein cholesterol (LDL-C) in C. nasus subjected to HFDs. Furthermore, it significantly upregulated the expression of the differentially expressed proteins (DEPs) implicated in cholesterol metabolism and fatty acid oxidation, while concurrently downregulating the DEPs associated with fatty acid synthesis. Additionally, probiotic supplementation significantly reduced the aspartate aminotransferase (AST), alanine aminotransferase (ALT), and malondialdehyde (MDA) levels induced by HFDs. It also upregulated the activities of catalase (CAT) and superoxide dismutase (SOD). Probiotic supplementation significantly upregulated the DEPs related to antioxidants, while significantly downregulating the DEPs associated with inflammatory responses and autophagy. These findings suggested that probiotics ameliorated HFD-induced hepatic lipid accumulation in C. nasus by enhancing cholesterol metabolism and fatty acid oxidation, concomitantly with the suppression of fatty acid synthesis pathways. Additionally, probiotics protected against HFD-induced hepatic injury by enhancing antioxidant defenses and suppressing inflammation in C. nasus. Full article

In this work, a novel method for the disposal of ladle furnace slag (LFS) and soda residue (SR) was proposed. By applying geopolymer technology, LFS and SR were used as precursors to manufacture a geopolymer with sufficient fresh and mechanical properties that can be used in construction works, such as in non-structural components like lightweight partition walls. The effects of raw material ratios and Na₂O equivalents on the fresh properties, mechanical properties, microstructure and environmental impact of LFS-SR geopolymer (LSG) were analyzed by rheology, compressive strength, XRD, TG/DTG, SEM, and calculation of embodied carbon. The results showed that the compressive strength of LSGs increased when the SR content decreased or Na₂O equivalent increased, and the maximum compressive strength could reach 12.0 MPa at 28 d. The hydration products of LSG were mainly C-(A)-S-H gel, C₃AH₆, and AFt. Notably, the C-(A)-S-H gels formed a stable cross-linked structure, and the extremely fine granular C₃AH₆ further filled the pores. Furthermore, AFt was generated from the interaction between LFS and CaSO₄ rich in SR during the hydration process. The carbon calculation results indicated that the embodied carbon of LSGs was significantly lower than that of traditional cement, and the LSG containing 20% SR and 12% Na₂O equivalent had the highest sustainability. This study proposed strategies for mitigating the environmental hazards of alkaline solid waste and improving its resource utilization, thereby promoting sustainable development in the construction industry. Full article

Inspired by the ventral scale structure of the oriental sand boa, this study successfully fabricated multiscale bioinspired alumina (Al₂O₃) ceramics by combining the excellent mechanical properties, high-temperature resistance, and high hardness of ceramic composites with direct ink writing (DIW) 3D printing technology and femtosecond laser processing. A MoS₂ thin film was then deposited on the ceramic surface via radio frequency magnetron sputtering (PVD) to systematically investigate the impact of bioinspired structures on the tribological properties of ceramic composites under both dry and lubricated conditions. Experimental results demonstrated that bioinspired structures at different scales exhibited significant friction-reducing and wear-resistant characteristics compared to blank structures. Specifically, under room-temperature conditions, the friction coefficients of bioinspired ceramic composites with solid lubricants and oil lubrication were 0.3 and 0.148, respectively, indicating excellent tribological performance. These findings confirm the synergistic lubrication effect between bioinspired structures, two-dimensional solid lubricants, and lubricating oil, which significantly enhanced the friction-reducing and wear-resistant properties of ceramic components. Therefore, the synergistic design of multiscale bioinspired structures and solid lubricants provides an innovative strategy for the advanced application of ceramic components. Full article

Three-dimensional (3D) virtual trees play a vital role in modern forestry research, enabling the visualization of forest structures and supporting diverse simulations, including radiation transfer, climate change impacts, and dynamic forest management. Current virtual tree modeling primarily relies on 3D point cloud reconstruction from field survey data, and this approach faces significant challenges in scalability and structural diversity representation, limiting its broader applications in ecological modeling of forests. To address these limitations, we propose Diff-Tree, a novel diffusion model-based framework for generating diverse and realistic tree point cloud with reduced dependence on real-world data. The framework incorporates an innovative tree realism-aware filtering mechanism to ensure the authenticity of generated data while maintaining structural diversity. We validated Diff-Tree using two distinct datasets: one comprising five tree species from different families and genera, and another containing five Eucalyptus species from the same genus, demonstrating the method’s versatility across varying taxonomic levels. Quantitative evaluation shows that Diff-Tree successfully generates realistic tree point cloud while effectively enhancing structural diversity, achieving average ${MMD}_{CD}$ and ${COV}_{CD}$ values of (0.41, 65.78) and (0.56, 47.09) for the two datasets, respectively. The proposed method not only significantly reduces data acquisition costs but also provides a flexible, data-driven approach for virtual forest generation that adapts to diverse research requirements, offering a more efficient and practical solution for forestry research and ecological modeling. Full article