Search Results (32)

This study investigates the thermal response and surface modification of low-carbon manganese-alloyed 20GL steel during electrolytic plasma hardening. The objective was to evaluate the feasibility of surface hardening 20GL steel—traditionally considered difficult to quench—by combining high-rate surface heating with rapid cooling in an electrolyte medium. To achieve this, a transient two-dimensional heat conduction model was developed to simulate temperature evolution in the steel sample under three voltage regimes. The model accounted for dynamic thermal properties and non-linear boundary conditions, focusing on temperature gradients across the thickness. Experimental temperature measurements were obtained using a K-type thermocouple embedded at a depth of 2 mm, with corrections for sensor inertia based on exponential response behavior. A comparison between simulation and experiment was conducted, focusing on peak temperatures, heating and cooling rates, and the effective thermal penetration depth. Microhardness profiling and metallographic examination confirmed surface strengthening and structural refinement, which intensified with increasing voltage. Importantly, the study identified a critical cooling rate threshold of approximately 50 °C/s required to initiate martensitic transformation in 20GL steel. These findings provide a foundation for future optimization of quenching strategies for low-carbon steels by offering insight into the interplay between thermal fluxes, surface kinetics, and process parameters. Full article

The Charpy impact toughness of single-phase austenitic Fe-32Mn-0.6C steel was systematically investigated across a wide temperature spectrum from 25 °C to −196 °C using Charpy V-notch impact tests. The material exhibited a remarkable temperature dependence of impact energy, decreasing dramatically from 120 J at ambient temperature (25 °C) to 13 J under cryogenic conditions (−196 °C). Notably, a steep transition in impact energy occurred within the critical temperature window of −100 °C to −150 °C. Microstructural analysis revealed that synergistic effects of high strain rates and low temperatures significantly restrict dislocation slip and multiplication mechanisms, while also suppressing deformation twinning activation. This restricted plasticity accommodation mechanism fundamentally differs from the deformation characteristics reported in conventional low-carbon high-manganese steels and other face-centered cubic (FCC) alloy systems. Full article

Solutions and new processes are continually being developed to produce components demonstrating high strength and elongation. This paper focuses on medium manganese steel with a composition of 0.2% carbon, 3% manganese, and 2.15% aluminium (by weight percent). The mechanical properties of the steel and the effect of aluminium and manganese on the microstructure are investigated. The steel sheets are shaped into omega profiles using a press tool, followed by the intercritical annealing of the samples to enhance their ductility. Before the experiment, the anticipated values were a tensile strength (UTS) of approximately 1100 MPa and elongation within 30–35%. A key objective was to achieve a microstructure that incorporates residual austenite. The experimental parameters were carefully derived from an extensive exploration to identify potential weaknesses in the experiment. The main parameters selected were the intercritical annealing (IA) temperature and IA dwell time. The results revealed that the highest recorded UTS was 1262 ± 6 MPa, while the maximum elongation achieved was 16 ± 1%. Full article

Ultra-low-carbon, high-strength steels have gained significant attention due to their exceptional mechanical properties. To enhance the performance of the steel, understanding the precipitation behavior of strengthening precipitates is crucial. In this study, the precipitation behavior of ultra-low-carbon high-strength steel strengthened by nanoscale copper (Cu)-rich precipitates (CRPs) and carbonitride (CN) atomic clusters was characterized using atom-probe tomography after tempering at 400, 450, 600, and 650 °C for 2 h. The results revealed that the nanoscale copper CRPs and the CN atomic clusters were the main strengthening precipitates. The CRPs, enriched only in Cu, were observed at 400 °C. Segregation of nickel (Ni) and manganese (Mn) to the CRPs occurred at 450 °C, and the number densities of CRPs achieved the maximum value, leading to the highest strengthening effects. The size of the CRPs increased with increasing temperature; however, the size of the clusters of the carbide-forming atoms remained at almost ~1.6 nm. At 650 °C, the concentration of Cu, Ni, and Mn atoms in the CRPs was about 85.4, 4.5, and 4 at.%, respectively; however, that of Fe decreased significantly. In the lath boundaries, the size of 10% C and 0.4% C iso-surfaces was relatively larger than that in the matrix. In a reverted austenite region at 600 °C, the concentration of Ni in the reverted austenite, CRPs, and matrix was about 15, 2.5, and 2.5 at.%, respectively. Full article

This study examines the deformation behaviour and fracture mechanisms of bimetal composites (BCs) composed of high-carbon medium-manganese steel (Mn8) and low-carbon steel (SS400), fabricated through hot roll bonding. The research highlights the effect of varying thickness ratios on the mechanical properties of Mn8/SS400 BCs. The microstructure and interfacial characteristics were analysed using scanning electron microscopy (SEM), revealing a well-bonded and defect-free interface with distinct elemental distributions. Tensile and bending tests were conducted to evaluate the composites’ mechanical performance, highlighting the synergistic effects of Mn8’s high strain hardening capacity and SS400’s ductility. Mathematical models, including the rule of mixtures (ROM) and the long-wavelength approach (LWA), were employed to predict the tensile strength and plastic instability strain (PIS), with experimental results showing deviations due to interfacial strengthening mechanisms and dislocation pile-ups. The findings provide insights into the interplay between layer thickness ratios, interfacial properties, and strain hardening, offering valuable guidance for optimising the design and industrial-scale production of Mn8/SS400 BCs. Full article

The potential of an optimization process with respect to reduced mass can be used to the full extent by utilizing a high-strength material as it is, among others, strength-dependent. For the additive manufacturing process, Powder Bed Fusion of Metals using a Laser Beam (PBF-LB/M), 316L is commonly used. PBF-LB/M/316L has its benefits, like good material properties, such as availability, corrosion resistance, strength, and ductility. Nevertheless, a higher-strength material is required to fully take advantage of the optimization process and achieve a greater reduction in the mass of manufactured parts. The high-strength austenitic stainless steel investigated in this study is Printdur^® HSA. Its main alloying elements are manganese, chromium, molybdenum, carbon, and nitrogen. The steel obtains its high strength properties from the alloyed carbon and nitrogen via solid solution hardening and improving the austenite stability. Therefore, it is defined as (C+N) steel. The datasheet of the powder manufacturer describes a yield strength (R_p0.2; 0.2% offset proof stress) of 915 MPa, an ultimate tensile strength of 1120 MPa, and an elongation at fracture of 30%. These are clear benefits in comparison to PBF-LB/M/316L. Since there are no further investigations made on Printdur^® HSA, a thorough investigation of material behavior, fatigue life, and microstructure is needed. Full article

The morphology and microstructure of pearlite formed in 100Mn13 high-carbon high-manganese steel aged, respectively, at 525 °C and 650 °C after 1050 °C water toughening treatment were observed and analyzed by a scanning electron microscope (SEM) and transmission electron microscope (TEM). The results show that some pearlite colonies are chrysanthemum-like and are composed of M₇C₃ lamellae and ferrite lamellae, maintaining an orientation relationship (OR) of ($\overline{3}$$3$$12$)_M7C3‖($0 \overline{2} 4$)_α, [$4 0 1$]_M7C3‖[$5 2 1$]_α. Moreover, the lamellae in pearlite colonies with chrysanthemum-like morphology are distributed in an emanative way, where there are protrusions and branches at the growth frontier. A growth physical model describing the growth process of chrysanthemum-like pearlite is proposed. Full article

Hydrogen is increasingly being recognized as a crucial element in reducing carbon emissions in the metallurgical industry. Its use in the steel sector is gaining momentum through various initiatives at high TRL levels. Moreover, hydrogen shows promise in other metal production processes as well. One application involves utilizing hydrogen for effective selective reduction copper from copper slags with a low amount of iron being reduced. Hydrogen can also be employed in the pre-reduction of manganese ore, leading to the carbon-free production of manganese metal through aluminothermic reactions. Additionally, hydrogen can be used in the processing of bauxite residue, where iron is partially or completely reduced to separate an iron-rich fraction, allowing for alumina recovery via leaching. Full article

To address global environmental concerns and reduce carbon dioxide emissions, countries worldwide are prioritizing the development of green, eco-friendly, and low-carbon energy sources. This emphasis has led to the growing importance of promoting clean energy industries like hydrogen energy and natural gas. These gases are typically stored and transported at cryogenic temperatures, making ultra-low temperature alloys indispensable as essential materials for the storage and transportation of liquid gas energy. With the temperature decreasing from room temperature (RT) to liquid nitrogen temperature (LNT), the dominant deformation mechanism in high-manganese steels undergoes a transformation from dislocation slip to deformation twinning, resulting in exceptional cryogenic mechanical properties. Consequently, high-manganese steel has emerged as an excellent material candidate for cryogenic applications. This report focuses on establishing the composition of high-manganese steel suitable for cryogenic applications and provides a comprehensive review of its microstructure and mechanical properties at both RT and LNT. Furthermore, it offers a prospective outlook on the future development of cryogenic high-manganese steels. Full article

Medium manganese steel has excellent comprehensive properties due to the TRIP effect of retained austenite, but its welding performance is unsatisfactory for its high alloy content. This study obtained retained austenite in low-carbon low-alloy steel with low contents of silicon and manganese elements through intercritical heat treatment. The influence of intercritical quenching temperature on the content and characteristics of the retained austenite, as well as the functional mechanism of the retained austenite during low-temperature impact, was studied. The results showed that the content of the retained austenite increased from 12% to 17%, and its distribution extended from grain boundaries to martensite lath boundaries, with increasing intercritical quenching temperature. The retained austenite on the grain boundaries was in blocks, and that on the martensitic lath boundaries formed slender domains. The stability of the retained austenite was achieved through the enrichment of C and Mn during intercritical heat treatment. The contribution of retained austenite to low-temperature mechanical properties was closely related to its stability. The retained austenite with poor stability underwent martensite transformation at low temperatures, and the high-carbon martensite was a brittle phase that became the nucleation site of cracks or the path of crack growth during impact. Stable retained austenite passivated crack tips and hindered crack propagation during impacts, which improved the impact performance of the steel. Full article

In this study, the relationship between macro segregation and the equiaxed zone in high-carbon grades with continuous casting parameters was investigated and optimized at the İsdemir iron and steel plant. The work was conducted for the 1080 quality of the SAE J403 standard. In this study, some parameters, such as casting speed, secondary cooling, EMS current value and EMS frequency value, were examined. When the results of the experiments are examined, it can be observed that the equiaxed zone in the macrostructure decreases significantly with the reduction of the EMS frequency value. The decrease in casting speed and increase in EMS current value caused an increase in the equiaxed zone. The increment in secondary cooling led to a decline in the equiaxed zone. Once the macro segregation results are examined, it can be seen that it is very important to optimize the continuous casting parameters in order to reduce the macro segregation results of—especially—carbon, sulfur and phosphorus elements. It has also been determined that the macro segregation values of carbon, sulfur and phosphorus elements are low in casting conditions where casting speed is low, and the EMS current value and EMS frequency value are high. In addition, macro segregation measurements of manganese, silicon, chromium and vanadium elements are found to be low under similar casting conditions. It is critical to optimize the continuous casting parameters before production, especially in high-carbon grades to be used for prestressed concrete wire and cord wire applications. As a result of the work conducted using the İsdemir billet continuous casting machine for the 1080-grade SAE J403 standard, aiming to optimize macro segregation and the equiaxed zone, the effective results have been achieved by using process parameters of 2.8 m/min casting speed, 360 A EMS current, 5 Hz EMS frequency and low secondary cooling intensity. Full article

The paper presents the study results of the parameters influence of arc welding with a consumable electrode with two-jet gas shielding in CO₂ on the structure and microhardness of high-strength steel 45 welded joints with slotted edges. Controlling the dynamic impact of the internal shielding gas jet on the processes in the welding zone changes the heat and mass transfer processes in the welding zone and results in the intensive mixing of the molten electrode metal with the base metal in the weld pool. The results of the studies determined the dynamic effect of the active shielding gas jet on the structure and microhardness of multilayered steel 45 welded joints with slotted edges using the method of full factorial experiment, developed dependences of chemical elements (carbon, silicon, manganese) content in the weld metal of multilayered steel 45 welded joints on the controlled parameters of the welding mode (Q, Iw, U). Due to uneven heat introduction into each of the welded plates during edge slotting, the asymmetric distribution of microhardness in the cross sections of welded joints relative to the weld axis indicates some differences in the structure and properties of the heat-affected zone (HAZ) and the weld. According to the results of the studies, consumable electrode arc welding with two-jet gas shielding provides faster distribution and equalization of heat on the product surface and reduces its instantaneous overheating, which improves the structural phase state of the welded joint made of steel 45 and reduces the microhardness gradient in the HAZ. An increase in the heat input of welding (a simultaneous increase in the welding current and voltage of the welding arc) leads to a decrease and smoothing of the microhardness peak in the HAZ. Full article

The tensile and impact deformation behavior of three different Mn content test steels, xMn-1.0C-0.25V-1.5Cr-0.3Mo (5, 8 and 13 wt%), were investigated using mechanical properties testing, SEM-EBSD and TEM. The elongation and −20 °C impact energy of the three types of Mn content test steels increased as the Mn content increased. The room temperature tensile elongation was 9%, 23% and 81%, and the −20 °C impact energy was 9 J, 99 J and 241 J, respectively. The fracture morphologies of 5 Mn and 8 Mn were found to be cleavage fractures with secondary cracks and micro-voids. The 13 Mn fracture morphology was a plastic fracture with many coarse dimples. Transverse cracks perpendicular to the tensile direction occurred on the surface of the gauge area of 5 Mn and 8 Mn tensile specimens, reducing plasticity dramatically. This was mainly related to the martensitic transformation produced by stress. We characterized the martensite near the tensile fracture and speculated the main mode of crack propagation. Furthermore, a little amount of sharp-shaped BCC phase was found in the 5 Mn, which was determined to be a hard phase relative to the austenite matrix by nanoindentation test. These steels have stacking fault energies ranging from ~15 to ~29 mJ/m² with increasing Mn content 13 Mn has high stacking fault energy (SFE) and austenite stability. Twin-induced plasticity (TWIP) was the deformation mechanism. Full article

In this paper, we investigate the effects of vanadium on the strength and ductility of medium-manganese steels by analyzing the microstructural evolution and strain hardening rates and performing quantitative calculations. Two significantly different contents of vanadium, 0.05 and 0.5 wt.%, were independently added to model steel (0.12C-10Mn) and annealed at different intercritical temperatures. The results show that higher vanadium addition increases the yield strength but decreases the ductility. The maximum yield strength can increase from 849 MPa to 1063 MPa at low temperatures. The model calculations reveal that this is due to a precipitation strengthening increment of up to 148 MPa and a dislocation strengthening increment of 50 MPa caused by a higher quantity of V₄C₃ precipitates. However, the high density of vanadium carbides leads them to easily segregate at grain boundaries or phase interfaces, which prevents strain from uniformly distributing throughout the phases. This results in stress concentrations which cause a high strain hardening rate in the early stages of loading and a delayed transformation-induced plasticity (TRIP) effect. Additionally, the precipitates decrease the austenite proportion and its carbon concentrations, rendering the TRIP effect unsustainable. Accordingly, the ductility of high vanadium steels is relatively low. Full article

The development of new lightweight materials is required for the automotive industry to reduce the impact of carbon dioxide emissions on the environment. The lightweight, high-manganese steels are the prospective alloys for this purpose. Hot deformation is one of the stages of the production of steel. Hot deformation behavior is mainly determined by chemical composition and thermomechanical parameters. In the paper, an artificial neural network (ANN) model with high accuracy was constructed to describe the high Mn steel deformation behavior in dependence on the concentration of the alloying elements (C, Mn, Si, and Al), the deformation temperature, the strain rate, and the strain. The approval compression tests of the Fe–28Mn–8Al–1C were made at temperatures of 900–1150 °C and strain rates of 0.1–10 s⁻¹ with an application of the Gleeble 3800 thermomechanical simulator. The ANN-based model showed high accuracy, and the low average relative error of calculation for both training (5.4%) and verification (7.5%) datasets supports the high accuracy of the built model. The hot deformation effective activation energy values for predicted (401 ± 5 kJ/mol) and experimental data (385 ± 22 kJ/mol) are in satisfactory accordance, which allows applying the model for the hot deformation analysis of the high-Mn steels with different concentrations of the main alloying elements. Full article