Search Results (3,525)

In metal cutting industries, optimizing the thermal conductivity and viscosity of vegetable oil-based cutting fluids is critical for ensuring efficient heat dissipation, effective lubrication, and sustainability, directly influencing tool life and machining performance. This study presents a comprehensive experimental analysis employing statistical methods, particularly Taguchi’s Design of Experiments, to evaluate the thermal conductivity and viscosity of Pongamia pinnata, sunflower, and coconut oil incorporated with Silicon Dioxide (SiO₂), Hexagonal Boron Nitride (hBN), and Cupric Oxide (CuO) nanoparticles across different emulsion ratios and nanoparticle volume fractions. The results revealed that Pongamia pinnata oil containing 0.5 (Vol.%) SiO₂ nanoparticles at an emulsion ratio of 1:7 achieved the maximum thermal conductivity, measured at 0.637 W/mK. Additionally, the results revealed that Pongamia pinnata oil at an emulsion ratio of 1:13 exhibited the highest viscosity of 1.33 mPa·S, confirming that both the type of cutting oil and the emulsion ratio are the primary factors influencing viscosity. Further, the ANOVA analysis for thermal conductivity and viscosity highlights that the type of cutting fluid is the dominant factor, accounting for 90.58% of the total variance in thermal conductivity and 70.47% in viscosity, each with a highly significant p-value of 0.00, underscoring its decisive impact on the stability of both properties. Overall, this research offers important guidance for the selection and formulation of vegetable oil-based emulsions with nanoparticle additives. The results support the development of advanced nano lubricants with enhanced performance, catering to the increasing requirements of diverse industrial applications. Full article

A conceptual design study is presented for a hemispherical, two-chamber water Cherenkov detector instrumented with bladder-embedded light traps. The detector consists of a rigid aluminium vessel enclosing a water volume that is divided into an outer, optically black chamber and a inner, reflective chamber lined by a flexible bladder. Arrays of light-trap modules, based on plastic scintillators with wavelength-shifting elements and thin silicon photomultipliers, are integrated into the bladder and selected inner surfaces. This geometry is intended to enhance muon tagging, increase acceptance for inclined air showers, and enable improved discrimination between electromagnetic and hadronic components. The study describes the mechanical and optical layout of the detector, the baseline aluminium housing, and the use of 3D-printed hexagonal prototypes to validate integration of the bladder and readout electronics. A first-order structural assessment based on thin-shell and plate theory is presented, indicating large safety margins for the hemispherical shells and identifying the flat base as the mechanically most loaded component. While GEANT4 simulations for detector response to extensive air showers in the atmosphere and performance measurements are left to future work, the present study establishes a mechanically validated, costed baseline design and outlines the steps needed to assess its impact in air-shower arrays. Full article

Dislocation reduction in gallium nitride (GaN) epitaxial layers remains a critical challenge for high-performance GaN-based electronic devices. In this study, GaN epitaxial growth on newly-developed 4H-Silicon Carbide (SiC) meta-substrates was systematically investigated to elucidate the role of surface pattern geometry in modulating dislocation propagation. A series of truncated-hexagonal-pyramid meta-structures with a fixed array period and varying pattern ratios (R) were designed and fabricated to enable controlled tuning of the effective surface morphology. Atomic force microscopy confirmed comparable surface flatness for all samples after epitaxial growth. Cathodoluminescence analysis revealed a non-monotonic dependence of defect density on R, indicating the existence of an optimal pattern geometry. Among all configurations, the outstanding sample exhibited the lowest defect density, achieving a 54.96% reduction in threading dislocations (edge + mixed) compared with a planar reference. Cross-sectional transmission electron microscopy further confirmed a substantially reduced dislocation density and clear evidence of dislocation bending and termination near the meta-structured regions. These results demonstrate that geometry-engineered 4H-SiC meta-substrates provide an effective and scalable strategy for dislocation modulation in GaN epitaxy on SiC meta-substrates, offering a promising pathway toward advanced GaN power and RF devices. Full article

Polyethylene waxes (PEWs) are considered promising mid-temperature phase change materials (PCMs). However, their low thermal conductivity limits both applicability and efficiency. One of the more interesting inorganic additives for PCMs is boron nitride (BN), which exhibits high thermal conductivity while remaining electrically insulating, excellent chemical and thermal stability, and good oxidation resistance. In this study, PEW was modified with hexagonal boron nitride (h-BN) in the range of 0.025 to 0.5 wt.%. Differential scanning calorimetry (DSC) results revealed that the addition of h-BN significantly alters the phase-transition behavior of polyethylene wax, broadens the melting and solidification temperature ranges, and reduces supercooling from 11 °C to 9 °C. Thermogravimetric analysis (TGA) showed that the incorporation of h-BN improves the thermal stability of the material. The temperature corresponding to 5% mass loss increased by about 50 °C after incorporation of more than 0.025% h-BN. The temperature of maximum mass-loss rate (T_DTGmax) was shifted about 8 °C toward higher temperatures. FTIR results indicate that h-BN does not change the chemical structure of polyethylene waxes, but does affect their morphology and physical properties by increasing the thermal conductivity from 0.30 to 0.40 mW/K. These effects enable the design of composites with tunable properties for energy-storage applications. Full article

This study investigates the dynamic behaviors of re-entrant unit-cell-shaped steel frames through numerical and experimental modal analyses. Inspired by re-entrant honeycomb structures, individual frame units were modeled to explore how natural frequencies vary with beam cross-sectional dimensions and frame angles. Twenty distinct frame models—incorporating four cross-sectional sizes (4 × 4 mm, 8 × 8 mm, 12 × 12 mm, and 16 × 16 mm) and five main frame angles (120°, 150°, 180°, 210°, and 240°)—were developed using 3D modeling and finite element analysis (FEA) tools, and the first eight natural frequencies and corresponding mode shapes were extracted for each model. The results reveal that lower modes exhibit global bending and torsional behaviors, whereas higher modes demonstrate increasingly localized deformations. It is found that the natural frequencies decrease in the straight frame configuration and increase in the hexagonal configurations, highlighting the critical influence of the frame geometry. Increasing the cross-sectional size consistently enhances the dynamic stiffness, particularly in hexagonal frames. A quadratic polynomial surface regression analysis was performed to model the relationship of the natural frequency with the cross-sectional dimension and frame angle, achieving high predictive accuracy (R² > 0.98). The experimental validation results were in good agreement with the numerical results, with discrepancies generally remaining below 7%. The developed regression model provides an efficient design tool for predicting vibrational behaviors and optimizing frame configurations without extensive simulations; furthermore, experimental modal analyses validated the numerical results, confirming the effectiveness of the model. Overall, this study provides a comprehensive understanding of the dynamic characteristics of re-entrant frame structures and proposes practical design strategies for improving vibrational performance, which is particularly relevant in applications such as machine foundations, vibration isolation systems, and aerospace structures. Full article

The Sakhalin pine sawyer, Monochamus saltuarius Gebler, 1830 (Coleoptera: Cerambycidae), is a newly discovered insect vector of the pine wood nematode (Bursaphelenchus xylophilus) in China. Despite its ecological importance, the detailed morphology of its sensory systems remains largely unexplored. This study presents comprehensive ultrastructural analysis of the compound eyes and stridulatory organs in adult M. saltuarius, with a focus on sexual differences. Our morphometric results revealed pronounced sexual dimorphism: males possessed significantly larger compound eyes in terms of total area and perimeter. Furthermore, all three types of ommatidial facets (hexagonal, pentagonal, and quadrilateral) exhibited significantly greater area, perimeter, and diameter in males. Interestingly, while the total number of ommatidia and the counts within the dorsal and ventral eye regions showed no significant sexual difference, they were strongly positively correlated with body length in both sexes. Regarding the stridulatory organs, key morphological features including the transverse diameter, longitudinal diameter, and width of the lateral sulcus of the stridulatory file were also significantly greater in males. In contrast, no sexual dimorphism was detected in the width or density of the stridulatory teeth. These findings collectively indicate a significant investment in sexually dimorphic sensory organs in M. saltuarius, which we hypothesize is closely linked to sex-specific behavioral roles, particularly in active mate searching, courtship displays, and intrasexual competition. This research provides a crucial morphological foundation for understanding the species’ visual and acoustic communication, supporting future work on its sensory ecology and the development of behavior-based control strategies for pine wilt disease. Full article

Excessive vibration during human knee joint movement poses challenges to biomechanical performance and comfort, which this study aims to mitigate through the design of a bio-inspired honeycomb-based vibration-damping structure, for the purpose of optimizing dynamic vibration absorption efficiency. Three honeycomb geometries—regular triangle, square, and regular hexagon—were evaluated via dynamic mechanical simulation, identifying the regular hexagon as the most effective base configuration. Using the control variable method within reasonable parameter ranges, finite element analysis was employed to systematically examine the influence of wall thickness, side length, and gradient of the regular hexagonal honeycomb on its damping performance. The findings demonstrate that vibration damping is maximized under a configuration with a wall thickness of 1.8 mm, a side length of 6 mm, and a gradient of 110%. Full article

The six platinum group elements (PGE) are among the rarest elements in the upper continental crust of the earth. Higher values of PGE have been detected in the upper mantle and in chondrite meteorites. The PGE are siderophile and chalcophile elements and are divided into the following: (1) the Ir subgroup (IPGE) = Os, Ir, and Ru and (2) the Pd subgroup (PPGE) = Rh, Pt, and Pd. The IPGE are more refractory and less chalcophile than the PPGE. High concentrations of PGE led, in rare cases, to the formation of mineral deposits. The PGE are carried in discrete phases, the platinum group minerals (PGM), and are included as trace elements into the structure of base metal sulphides (BM), such as pentlandite, chalcopyrite, pyrite, and pyrrhotite. Similarly to PGE, the PGM are also divided into two main groups, i.e., IPGM composed of Os, Ir, and Ru and PPGM containing Rh, Pt, and Pd. The PGM occur both in mafic and ultramafic rocks and are mainly hosted in stratiform reefs, sulphide-rich lenses, and placer deposits. Presently, there are only 169 valid PGM that represent about 2.7% of all 6176 minerals discovered so far. However, 496 PGM are listed among the valid species that have not yet been officially accepted, while a further 641 are considered as invalid or discredited species. The main reason for the incomplete characterization of PGM resides in their mode of occurrence, i.e., as grains in composite aggregates of a few microns in size, which makes it difficult to determine their crystallography. Among the PGM officially accepted by the IMA, only 13 (8%) were discovered before 1958, the year when the IMA was established. The highest number of PGM was discovered between 1970 and 1979, and 99 PGM have been accepted from 1980 until now. Of the 169 PGM accepted by the IMA, 44% are named in honour of a person, typically a scientist or geologist, and 31% are named after their discovery localities. The nomenclature of 25% of the PGM is based on their chemical composition and/or their physical properties. PGM have been discovered in 25 countries throughout the world, with 64 from Russia, 17 from Canada and South Africa (each), 15 from China, 12 from the USA, 8 from Brazil, 6 from Japan, 5 from Congo, 3 from Finland and Germany (each), 2 from the Dominican Republic, Greenland, Malaysia, and Papua New Guinea each, and only 1 from Argentine, Australia, Bulgaria, Colombia, Czech Republic, England, Ethiopia, Guyana, Mexico, Serbia, and Tanzania each. Most PGM phases contain Pd (82 phases, 48% of all accepted PGM), followed, in decreasing order of abundances, by those of Pt 35 phases (21%), Rh 23 phases (14%), Ir 18 phases (11%), Ru 7 phases (4%), and Os 4 phases (2%). The six PGE forming the PGM are bonded to other elements such as Fe, Ni, Cu, S, As, Te, Bi, Sb, Se, Sn, Hg, Ag, Zn, Si, Pb, Ge, In, Mo, and O. Thirty-two percent of the 169 valid PGM crystallize in the cubic system, 17% are orthorhombic, 16% hexagonal, 14% tetragonal, 11% trigonal, 3% monoclinic, and only 1% triclinic. Some PGM are members of a solid-solution series, which may be complete or contain a miscibility gap, providing information concerning the chemical and physical environment in which the mineral was formed. The refractory IPGM precipitate principally in primitive, high-temperature, mantle-hosted rocks such as podiform and layered chromitites. Being more chalcophile, PPGE are preferentially collected and concentrated in an immiscible sulphide liquid, and, under appropriate conditions, the PPGM can precipitate in a thermal range of about 900–300 °C in the presence of fluids and a progressive increase of oxygen fugacity (fO₂). Thus, a great number of Pt and Pd minerals have been described in Ni-Cu sulphide deposits. Two main genetic models have been proposed for the formation of PGM nuggets: (1) Detrital PGM represent magmatic grains that were mechanically liberated from their primary source by weathering and erosion with or without minor alteration processes, and (2) PGM reprecipitated in the supergene environment through a complex process that comprises solubility, the leaching of PGE from the primary PGM, and variation in Eh-pH and microbial activity. These two models do not exclude each other, and alluvial deposits may contain contributions from both processes. Full article

As one of the key payloads for space-borne gravitational wave detection (SGWD), the phasemeter is primarily responsible for conducting phase measurements of heterodyne signals. A phase extraction precision at the micro-radian level constitutes a crucial performance metric for intersatellite heterodyne interferometry. In this work, an ultra-stable hexagonal optical bench was developed using hydroxide-catalysis bonding technology. Different beat-notes were generated in accordance with the requirements of four experimental stages, which were applied to simulate the main beat-note of the inter-satellite scientific interferometer, thereby verifying the phase measurement performance of the phasemeter for beat-notes. Experimental results demonstrate that the phase extraction precision meets the index requirement of $2\pi \mu \mathrm{rad}/\sqrt{\mathrm{Hz}}$ for SGWD missions. Based on the test environment of the ultra-stable hexagonal optical bench, the feasibility of the phasemeter’s core phase measurement function was verified, laying a solid foundation for subsequent research on its auxiliary functions and extended tests. Full article

One-dimensional ZnO nanowires offer significant potential for optoelectronic applications, though their controlled synthesis remains challenging. This study optimized ZnO nanowire growth via carbothermal reduction vapor transport based on the vapor–liquid–solid mechanism. Key parameters investigated were gold catalyst thickness and annealing, source temperature, system pressure, and oxygen concentration. Results show that thinner Au films promote high-density, small-diameter nanowires. An optimal source temperature window (950–1000 °C) was identified, while pressure and oxygen content critically influenced growth mode by modulating vapor supersaturation. Under optimized conditions, aligned single-crystalline ZnO nanowires with hexagonal wurtzite structure were achieved. Structural and optical characterization confirmed high crystallinity and strong near-band-edge emission, demonstrating the efficacy of the developed approach for tailored nanowire synthesis. Full article

Corrosion in harsh environments causes global economic losses exceeding 3 trillion US dollars annually. Traditional silicone epoxy (SE) coatings are prone to failure due to insufficient physical barrier properties and lack of active protection. In this study, cerium dioxide (CeO₂) was in situ grown on the surface of hexagonal boron nitride (h-BN) mediated by polydopamine (PDA) to prepare BN-PDA-CeO₂ ternary nanocomposites, which were then incorporated into SE coatings to construct a multi-scale synergistic corrosion protection system. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and transmission electron microscopy (TEM) confirmed the successful preparation of the composites, where PDA inhibited the agglomeration of h-BN and CeO₂ was uniformly loaded. Electrochemical tests showed that the corrosion inhibition efficiency of the extract of this composite for 2024 aluminum alloy reached 99.96%. After immersing the composite coating in 3.5 wt% NaCl solution for 120 days, the coating resistance (Rc) and charge transfer resistance (Rct) reached 8.5 × 10⁹ Ω·cm² and 1.2 × 10¹⁰ Ω·cm², respectively, which were much higher than those of pure SE coatings and coatings filled with single/binary fillers. Density functional theory (DFT) calculations revealed the synergistic mechanisms: PDA enhanced interfacial dispersion (adsorption energy of −0.58 eV), CeO₂ captured Cl⁻ (adsorption energy of −4.22 eV), and Ce³⁺ formed a passive film. This study provides key technical and theoretical support for the design of long-term corrosion protection coatings in harsh environments such as marine and petrochemical industries. Full article

This study aimed to experimentally investigate the differences in metallic structures owing to the gas nitriding and quenching process (GNQP) temperature of the Ti-15mass%Nb alloy and differences in the tribological properties of the surface layer. The GNQP heating temperature was 1023 K or 1223 K, and the holding time was set to 1 h. In the X-ray diffraction profiles, the diffraction peak of the (10$\overline{1}$1) plane of the hexagonal close-packed phase exhibited a shift toward lower angles, following the sequence AN:α, AQ:α′, and GNQP:α-TiN_0.3. In both the 1023 K and 1223 K GNQP specimens, the α″ phase exhibited lower values than the α′ phase; nonetheless, it still exhibited larger values than the annealed α phase. Based on transmission electron microscopy observations, the high core hardness of the 1223 K GNQP specimen was attributed to solid-solution strengthening caused by nitrogen diffusion or to strain hardening associated with the diffusion and was not attributed to the influence of precipitation phases, such as the ω phase. In the friction and wear tests, both the 1023 K and 1223 K GNQP specimens exhibited narrower wear track widths, clearly demonstrating that the GNQP enhanced the wear resistance. Moreover, the TiO₂ layer was effective in maintaining a low coefficient of friction. Full article

This paper focuses on power grid integration of wave energy converter (WEC) arrays that minimize added energy storage for maximizing power capture as well as smoothing the oscillatory power inputs into the grid. In particular, a linear right circular cylinder WEC array that implements complex conjugate control is compared and contrasted to a nonlinear WEC array that implements an hourglass buoy shape while both are integrated into the grid utilizing phase control (i.e., relative spacing of the WEC array) on the input powers to the grid. The Hamiltonians of the two WEC systems are derived, enabling a direct comparison of real and reactive power, with reactive power reflecting the utilization of stored energy. The control systems are simulated in MATLAB/Simulink under both regular wave conditions and irregular seas generated from a Bretschneider spectrum. For the linear right circular cylinder buoy, the proportional-derivative complex conjugate controller requires an external energy storage device to supply reactive power, whereas the nonlinear hourglass buoy inherently provides reactive power through its geometric design. This study demonstrates that: (i) The unique geometry of the hourglass buoy reduces the required energy storage size for the nonlinear system while simultaneously increasing power output. (ii) Phase control of the hexagonal hourglass array further enhances real power capture. Together, these effects substantially decrease the size and demand on the individual buoys and grid integration energy storage requirements. Full article

Fiber laser surface texturing was applied to AA1050 aluminum to improve friction and wear performance of PTFE coatings. A Taguchi L16 design varied texture geometry (square, diamond, hexagon, circle), scanned area ratio (20% to 80%), and laser power (40 to 100 W) prior to primer plus PTFE topcoat deposition (25 to 35 µm). Dry reciprocating sliding against a 6 mm 100Cr6 ball was conducted at 20 N, 1 Hz, and 50 m, and wear track geometry was measured by non-contact profilometry. The non-textured reference exhibited an average COF of 0.143, whereas the lowest mean COF was achieved with diamond 60% and 40 W (0.095) and the highest with hexagon 60% and 100 W (0.156); hexagon 20% and 60 W matched the reference. ANOVA indicated scanned area ratio as the dominant contributor to COF (39.72%), followed by geometry (35.07%) and power (25.21%). Profilometry confirmed reduced coating penetration for optimized textures: the reference wear track was approximately 1240 µm wide and 82 µm deep, compared with 930 µm and 34 µm for square 80% and 40 W, 997 µm and 39 µm for diamond 60% and 40 W, and 965 µm and 36 µm for hexagon 40% and 40 W. Full article

To address the complex surface curvature, massive dimensions, and variable pitch angles of wind turbine blades, this paper proposes a climbing robot design based on a variable-cell mechanism. By dynamically adjusting the support span and body posture, the robot adapts to the geometric features of different blade regions, enabling stable and efficient non-destructive inspection operations. Two reconfigurable configurations—a planar quadrilateral and a regular hexagon—are proposed based on the geometric characteristics of different blade regions. The configuration switching conditions and multi-leg cooperative control mechanisms are investigated. Through static stability margin analysis, the stable gait space and maximum stride length for each configuration are determined, optimizing the robot’s motion performance on surfaces with varying curvature. Simulation and experimental results demonstrate that the proposed multi-configuration gait planning strategy exhibits excellent adaptability and climbing stability across segments of varying curvature. This provides a theoretical foundation and methodological support for the engineering application of robots in wind turbine blade maintenance. Full article