Search Results (59)

High safety gel polymer electrolyte (GPE) is used in lithium metal solid state batteries, which has the advantages of high energy density, wide temperature range, high safety, and is considered as a subversive new generation battery technology. However, solid-state lithium batteries with multiple layers and large capacity currently have poor cycle life and a large gap between the actual output cycle capacity retention rate and the theoretical level. In this paper, polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP)/polyacrylonitrile (PAN)—lithium perchlorate (LiClO₄)—lithium lanthanum zirconium tantalate (LLZTO) gel polymer electrolytes was prepared by UV curing process using a UV curing machine at a speed of 0.01 m/min for 10 s, with the temperature controlled at 30 °C and wavelength 365 nm. In order to study the performance and failure mechanism of multilayer solid state batteries, single and three layers of solid state batteries with ceramic/polymer composite gel electrolyte were assembled. The results show that the rate and cycle performance of single-layer solid state battery with gel electrolyte are better than those of three-layer solid state battery. As the number of cycles increases, the interface impedance of both single-layer and three-layer electrolyte membrane solid-state batteries shows an increasing trend. Specifically, the three-layer battery impedance increased from 17 Ω to 42 Ω after 100 cycles, while the single-layer battery showed a smaller increase, from 2.2 Ω to 4.8 Ω, indicating better interfacial stability. After 100 cycles, the interface impedance of multi-layer solid-state batteries increases by 9.61 times that of single-layer batteries. After 100 cycles, the corresponding capacity retention rates were 48.9% and 15.6%, respectively. This work provides a new strategy for large capacity solid state batteries with gel electrolyte design. Full article

Gel-polymer electrolytes offer a promising route toward safer and more stable sodium-ion batteries, but conventional polymer systems often suffer from low ionic conductivity and limited voltage stability. In this study, we developed composite GPEs by embedding methylammonium lead chloride (CH₃NH₃PbCl₃, MPCl) into a UV-crosslinked ethoxylated trimethylolpropane triacrylate (ETPTA) matrix, with sodium alginate (SA) as an ionic conduction enhancer. Three types of membranes—GPE-P, GPE-El, and GPE-Eh—were synthesized and systematically compared. Among them, the high-MPCl formulation (GPE-Eh) exhibited the best performance, achieving a high ionic conductivity of 2.14 × 10⁻³ S·cm⁻¹, a sodium-ion transference number of 0.66, and a wide electrochemical window of approximately 4.9 V vs. Na⁺/Na. In symmetric Na|GPE|Na cells, GPE-Eh enabled stable sodium plating/stripping for over 600 h with low polarization. In Na|GPE|NVP cells, it delivered a high capacity retention of ~79% after 500 cycles and recovered ~89% of its initial capacity after high-rate cycling. These findings demonstrate that the perovskite–polymer composite structure significantly improves ion transport, interfacial stability, and electrochemical durability, offering a viable path for the development of next-generation quasi-solid-state sodium-ion batteries. Full article

Nanostructured bimetallic IrSn composites deposited on the natural aluminosilicate montmorillonite were synthesized and evaluated as anode electrocatalysts for polymer electrolyte membrane electrolysis cells (PEMECs). The test series prepared via the sol–gel method consisted of samples with 30 wt. % total metal content and varying Ir:Sn ratio. The performed X-ray diffraction analysis and high-resolution transmission electron icroscopy registered very fine nanostructure of the composites with metal particles size of 2–3 nm homogeneously dispersed on the support surface and also intercalated in the basal space of its layered structure. The electrochemical behavior was investigated by cyclic voltammetry and steady-state polarization techniques. The initial screening was performed in 0.5 M H₂SO₄. Then, the catalysts were integrated as anodes in membrane electrode assemblies (MEAs) and tested in a custom-made PEMEC. The electrochemical tests revealed that the catalysts with Ir:Sn ratio 15:15 and 18:12 wt. % demonstrated high efficiency toward the oxygen evolution reaction during repetitive potential cycling and sustainable performance with current density in the range 140–120 mA cm⁻² at 1.6 V vs. RHE during long-term stability tests. The results obtained give credence to the studied IrSn/MMT nanocomposites to be considered promising, cost-efficient catalysts for the oxygen evolution reaction (OER). Full article

Gel electrolytes (GEs) play a pivotal role in the advancement of lithium metal batteries by offering high energy density and enhanced rate capability. Nevertheless, their real-world application is hampered by relatively low ionic conductivity and significant interfacial resistance at room temperatures. In this work, we developed a gel electrolyte membrane (GEM) by embedding Zeolitic Imidazolate Framework-8 (ZIF-8) metal–organic frameworks (MOFs) material into a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix through UV curing. The composite membrane, with 4 wt% ZIF-8, exhibited an ionic conductivity of 1.17 × 10⁻³ S/cm, an electrochemical stability window of 4.7 V, and a lithium-ion transference number of 0.7. The test results indicate that the electrochemical performance of LFP//GEM//Li battery has an initial specific capacity of 168 mAh g⁻¹ at 0.1 C rate. At 1 C, the discharge capacity was 88 mAh g⁻¹, and at 2 C, it was 68 mAh g⁻¹. Enhanced ionic transport, improved electrochemical stability, and optimized lithium-ion migration collectively contributed to superior rate performance and prolonged cycle life. This study offers novel insights and methodological advances for next-generation lithium metal batteries technologies. Full article

The poor thermal stability of polypropylene (PP) separators poses risks of electrolyte leakage and battery short-circuiting, limiting their application in lithium metal batteries (LMBs). To address these challenges, a gel polymer membrane was designed using polymer blending technology. This membrane effectively retains the electrolyte, provides a stable environment, enhances thermal stability, and significantly decreases the risk of battery explosions and side reactions between the lithium metal and the electrolyte. Compared to commercial PP separators, the developed blend-type gel polymer electrolyte (b-GPE) demonstrates a superior performance, including structural stability at temperatures up to 150 °C and a high lithium-ion transference number ($t_{{Li}^{+}}$) of 0.513. Furthermore, a cell with a LiCoO₂ cathode operated at a 1 C rate retains 97.4% of its capacity after 300 cycles. After exposure to 120 °C, the b-GPE-120 demonstrates that its performance is comparable to that of the b-GPE, such as a $t_{{Li}^{+}}$ of 0.506, a high electrolyte absorption rate, and a wide electrochemical window of 5.2 V. Full article

Sodium-ion batteries (SIBs) are considered the next-generation candidates for partially substituting for commercial lithium-ion batteries in future energy storage systems because of the abundant sodium/potassium reserves and these batteries’ cost-effectiveness and high safety. Gel polymer electrolytes (GPEs) have become a popular research focus due to their advantages in terms of safety and performance in research on quasi-solid-state sodium-ion batteries (QSSIBs). Building on previous studies that incorporated MOF fillers into polymer-based gel electrolytes, we propose a 3D sandwich structure in which MOF materials are first pressed into thin films and then coated and protected by polymer materials. Using this approach, we achieved an ion conductivity of 1.75 × 10⁻⁴ S cm⁻¹ at room temperature and an ion transference number of 0.69. Solid-state sodium-ion batteries using this gel film electrolyte exhibited long cycling stability at a 2 C current density, retaining 75.2% of their specific capacity after 500 cycles. Full article

Zwitterionic polymers have garnered significant attention for their distinctive properties, such as biocompatibility, antifouling capabilities, and resistance to protein adsorption, making them promising candidates for a wide range of applications, including drug delivery, oil production inhibitors, and water purification membranes. This study reports the synthesis and characterization of zwitterionic monomers and polymers through the modification of linear, vinyl, and aromatic heterocyclic functional groups via reaction with 1,3-propanesultone. Four zwitterionic polymers with varying molecular structures—ranging from linear to five and six membered ring systems—were synthesized: poly(sulfobetaine methacrylamide) (pSBMAm), poly(sulfobetaine-1-vinylimidazole) (pSB1VI), poly(sulfobetaine-2-vinylpyridine) (pSB2VP), and poly(sulfobetaine-4-vinylpyridine) (pSB4VP). Their molecular weights, thermal behavior, and self-assembly properties were analyzed using gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and zeta potential measurements. The glass transition temperatures (Tg) ranged from 276.52 °C for pSBMAm to 313.69 °C for pSB4VP, while decomposition temperatures exhibited a similar trend, with pSBMAm degrading at 301.03 °C and pSB4VP at 387.14 °C. The polymers’ self-assembly behavior was strongly dependent on pH and their surface charge, particularly under varying pH conditions: spherical micelles were observed at neutral pH, while fractal aggregates formed at basic pH. These results demonstrate that precise modifications of the chemical structure, specifically in the linear, imidazole, and pyridine moieties, enable fine control over the thermal properties and self-assembly behavior of polyzwitterions. Such insights are essential for tailoring polymer properties for targeted applications in filtration membranes, drug delivery systems, and solid polymer electrolytes, where thermal stability and self-assembly play crucial roles. Full article

Because of safety concerns associated with the use of liquid electrolytes and electrolyte solutions, options for non-liquid materials like gels and polymers to be used as ion-conducting electrolytes have been explored intensely, and they attract steadily growing interest from researchers. The low ionic conductivity of most hard and soft solid materials was initially too low for practical applications in supercapacitors, which require low internal resistance of a device and, consequently, highly conducting materials. Even if an additional separator may not be needed when the solid electrolyte already ensures reliable separation of the electrodes, the electrolytes prepared as films or membranes as thin as practically acceptable, resistance may still be too high even today. Recent developments with gel electrolytes sometimes approach or even surpass liquid electrolyte solutions, in terms of effective conductance. This includes materials based on biopolymers, renewable raw materials, materials with biodegradability, and better environmental compatibility. In addition, numerous approaches to improving the electrolyte/electrode interaction have yielded improvements in effective internal device resistance. Reported studies are reviewed, material combinations are sorted out, and trends are identified. Full article

This paper reports on the novel composite membrane electrolytes used in Zn/MnO₂, Al/MnO₂, Al/air, and zinc/air electrochemical devices. The composite membranes were made using poly(vinyl alcohol), poly(acrylic acid), and a sulfonated polypropylene/polyethylene separator to enhance the electrochemical characteristics and dimensional stability of the solid electrolyte membranes. The ionic conductivity was improved significantly by the amount of acrylic acid incorporated into the polymer systems. In general, the ionic conductivity was also enhanced gradually as the testing temperature increased from 20 to 80 °C. Porous zinc gel electrodes and pure aluminum plates were used as the anodes, while porous carbon air electrodes or porous MnO₂ electrodes were used as the cathodes. The cyclic voltammetry properties and electrochemical impedance characteristics were investigated to evaluate the cell behavior and electrochemical properties of these prototype cells. The results showed that these prototype cells had a low bulk resistance, a high cell power density, and a unique device stability. The Al/MnO₂ cell achieved a density of 110 mW cm⁻² at the designated current density for the discharge tests, while the other cells also exhibited good values in the range of 70–100 mW cm⁻². Furthermore, the Zn/air cell consisting of the PVA/PAA = 10:5 composite membrane revealed an excellent discharge capacity of 1507 mAh. This represented a very high anode utilization of 95.7% at the C/10 rate. Full article

Using a novel technique, crosslinked gel polymer electrolytes (GPEs) designed for lithium-ion battery applications have been created. To form the photo crosslink via free-radical polymerization, a mixture of polyurethane acrylate (PUA), polyurethane methacrylate (PUMA), vinyl phosphonic acid (VPA), and bis[2-(methacryloyloxy)ethyl] phosphate (BMEP) was exposed to ultraviolet (UV) radiation during the fabrication process. The unique crosslinked configuration of the membrane increased its stability and made it suitable for use with liquid electrolytes. The resulting GPE has a much higher ionic conductivity (1.83 × 10⁻³ S cm⁻¹) than the commercially available Celgrad2500 separator. A crosslinked structure formed by the hydrophilic properties of the PUA-PUMA blend and the higher phosphate content from BMEP reduced the leakage of the electrolyte solution while at the same time providing a greater capacity for liquid retention, significantly improving the mechanical and thermal stability of the membrane. GPP2 shows electrochemical stability up to 3.78 V. The coin cell that was assembled with a LiFePO₄ cathode had remarkable cycling characteristics and generated a high reversible capacity of 149 mA h g⁻¹ at 0.1 C. It also managed to maintain a consistent Coulombic efficiency of almost 100%. Furthermore, 91.5% of the original discharge capacity was maintained. However, the improved ionic conductivity, superior electrochemical performance, and high safety of GPEs hold great promise for the development of flexible energy storage systems in the future. Full article

Zn–air batteries (ZABs) are a promising technology; however, their commercialization is limited by challenges, including those occurring in the electrolyte, and thus, gel polymer electrolytes (GPEs) and hydrogels have emerged as substitutes for traditional aqueous electrolytes. In this work, PVA/PAA membranes were synthesized by the solvent casting method and soaked in 6 M KOH to act as GPEs. The thickness of the membrane was modified (50, 100, and 150 μm), and after determining the best thickness, the membrane was modified with synthesized SiO₂ nanospheres and multi-walled carbon nanotubes (CNTs). SEM micrographs revealed that the CNTs displayed lengths of tens of micrometers, having a narrow diameter (95 ± 7 nm). In addition, SEM revealed that the SiO₂ nanospheres had homogeneous shapes with sizes of 110 ± 10 nm. Physicochemical experiments revealed that SiO₂ incorporation at 5 wt.% increased the water uptake of the PVA/PAA membrane from 465% to 525% and the ionic conductivity to 170 mS cm⁻¹. The further addition of 0.5 wt.% CNTs did not impact the water uptake but it promoted a porous structure, increasing the power density and the stability, showing three-times-higher rechargeability than the ZAB operated with the PVA/PAA GPE. Full article

Solid-state supercapacitors with gel electrolytes have emerged as a promising field for various energy storage applications, including electronic devices, electric vehicles, and mobile phones. In this study, nanocomposite gel membranes were fabricated using the solution casting method with perfluorosulfonic acid (PFSA) ionomer dispersion, both with and without the incorporation of 10 wt.% montmorillonite (MMT). MMT, a natural clay known for its high surface area and layered structure, is expected to enhance the properties of supercapacitor systems. Manganese oxide, selected for its pseudocapacitive behavior in a neutral electrolyte, was synthesized via direct co-precipitation. The materials underwent structural and morphological characterization. For electrochemical evaluation, a two-electrode Swagelok cell was employed, featuring a carbon xerogel negative electrode, a manganese dioxide positive electrode, and a PFSA polymer membrane serving as both the electrolyte and separator. The membrane was immersed in a 1 M Na₂SO₄ solution before testing. A comprehensive electrochemical analysis of the hybrid cells was conducted and compared with a symmetric carbon/carbon supercapacitor. Cyclic voltammetric curves were recorded, and galvanostatic charge–discharge tests were conducted at various temperatures (20, 40, 60 °C). The hybrid cell with the PFSA/MMT 10 wt.% exhibited the highest specific capacitance and maintained its hybrid profile after prolonged cycling at elevated temperatures, highlighting the potential of the newly developed membrane. Full article

TiO₂-based mixed oxide–carbon composite support for Pt electrocatalysts provides higher stability and CO tolerance under the working conditions of polymer electrolyte membrane fuel cells compared to traditional carbon supports. Non-traditional carbon materials like graphene nanoplatelets and graphite oxide used as the carbonaceous component of the composite can contribute to its affordability and/or functionality. Ti_(1−x)Mo_xO₂-C composites involving these carbon materials were prepared through a sol–gel route; the effect of the extension of the procedure through a solvothermal treatment step was assessed. Both supports and supported Pt catalysts were characterized by physicochemical methods. Electrochemical behavior of the catalysts in terms of stability, activity, and CO tolerance was studied. Solvothermal treatment decreased the fracture of graphite oxide plates and enhanced the formation of a reduced graphene oxide-like structure, resulting in an electrically more conductive and more stable catalyst. In parallel, solvothermal treatment enhanced the growth of mixed oxide crystallites, decreasing the chance of formation of Pt–oxide–carbon triple junctions, resulting in somewhat less CO tolerance. The electrocatalyst containing graphene nanoplatelets, along with good stability, has the highest activity in oxygen reduction reaction compared to the other composite-supported catalysts. Full article

The new hybrid composite materials for PEM fuel cell were synthesized by the UV polymerization of acrylic monomers (acrylonitrile, acrylic acid, ethylene glycol dimethacrylate) and a sulfo aromatic monomer, i.e., sodium styrene sulfonate, and the tetraethoxysilane/3-methacryloxypropyltrimethoxysilane-based sol–gel system. By means of X-ray spectroscopy, the fractal structure of the obtained materials was characterized. Proton conductivity and viscoelasticity of the obtained materials were determined depending on the content of the inorganic component in nanocomposites. Based on impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite’s electrolyte membranes. Full article

Printed textile-based flexible batteries are gaining attention in several applications, but they are becoming more relevant to the health care industry in terms of realizing wearable and skin-conformable electronic devices. A flexible battery must ideally be deformable along multiple directions. In this work, with an aim to develop a fully printed omnidirectional deformable battery, we report the fabrication process of a novel single-polymer-based flexible non-rechargeable planar Ag₂O-Zn battery on a textile substrate using the stencil printing method. Except for the electrolyte, all the components of the battery, including the current collectors, the anode, the cathode, and the separator membrane, are fabricated using a single polymer, namely styrene–ethylene–butylene–styrene (SEBS). To fabricate the SEBS separator, we introduce the solvent evaporation-induced phase separation (SEIPS) process. In the SEIPS method, toluene and dimethyl sulfoxide (DMSO) are selected as the solvent–nonsolvent pair. The SEBS: toluene: DMSO system with a wt% ratio of 6:85:9 showed improved performance regarding the OCV tests. A polyacrylic acid (PAA)-based alkaline polymer gel is used as an electrolyte. The demonstrated process is simple, and, with suitable modifications, it should find its use in the development of digitally printed alkaline batteries. Full article