Search Results (1,542)

Traumatic fractures are common in small animal emergency care, yet subtle fracture lines may be difficult to identify accurately using routine three-dimensional reconstruction workflows, particularly when access to specialized software is limited. This study describes the use of the open-source platform Three-Dimensional Slicer for computed tomography-based reconstruction and three-dimensional printing in a small dog with cranial trauma, with emphasis on documenting a practical and reproducible workflow through voxel resampling. Imaging data were imported into the software, bone structures were segmented using a rapid workflow, voxel spacing was resampled for smoother surface visualization by volume resampling, and the reconstructed model was processed for physical printing. Digital models of different resolutions were generated within minutes, and a life-size skull model was successfully fabricated using fused deposition modeling in less than three hours at a material cost of under one United States dollar. The enhanced model provided an intuitive representation of fracture morphology and spatial relationships compared with routine reconstruction alone. These findings demonstrate that open-source software combined with low-cost printing can provide a rapid, affordable, and user-friendly approach for practical skeletal reconstruction in small animals, with practical value for fracture assessment, preoperative planning, and broader use in resource-limited veterinary settings. Full article

Fused deposition modeling (FDM) provides a flexible manufacturing route for continuous fiber-reinforced thermoplastic composites, but weak interlaminar bonding and the trade-off between load-bearing capacity and deformation capability still limit their structural applications. In this study, multi-scale carbon/Kevlar fiber hybridization was introduced into acrylonitrile butadiene styrene (ABS)-based composites by combining continuous carbon fiber (CCF) or continuous Kevlar fiber (CKF) with short carbon fiber-filled ABS (ABS/SCF) or short Kevlar fiber-filled ABS (ABS/SKF). Four hybrid configurations and two continuous-fiber baseline composites were fabricated by FDM and evaluated through three-point bending tests, floating roller peel tests, peeled-surface SEM observations, and Rule-of-Mixtures-based hybrid effect analysis. The flexural results showed that short-fiber-filled matrices improved the flexural properties of both CCF- and CKF-based composites, but the degree of improvement depended on the fiber combination. Among the investigated configurations, CCF + ABS/SCF exhibited the highest flexural modulus and strength, which were 34.31% and 27.26% higher than those of CCF + ABS, respectively. For the CKF-based composites, CKF + ABS/SCF increased the flexural modulus and strength by 31.51% and 26.78%, compared with CKF + ABS, while maintaining the progressive deformation behavior associated with Kevlar reinforcement. The peel results showed that all hybrid composites had higher interlaminar peel resistance than their corresponding baselines, with increases ranging from 18.66% to 54.42%. The peeled-surface SEM observations indicated that the short-fiber-filled matrices changed the crack-propagation features, with more matrix tearing, fiber pull-out, and irregular peeling areas. The RoM-based comparison showed that the measured flexural properties of all hybrid configurations were higher than the corresponding RoM reference values. Overall, CCF + ABS/SCF was more suitable for improving stiffness and load-bearing capacity, whereas CKF + ABS/SCF showed a more balanced response in terms of flexural performance, interlaminar peel resistance, and progressive deformation behavior. Full article

Resveratrol (RSV) is a poorly water-soluble polyphenolic compound with various potential health benefits, but its pharmaceutical application is limited by low aqueous solubility and poor oral bioavailability. Additive manufacturing (AM), particularly fused deposition modeling (FDM) 3D printing, offers a flexible approach for fabricating oral dosage forms with customized geometry and internal architecture. In this study, hot-melt extrusion (HME) combined with fused deposition modeling (FDM) 3D printing was used to prepare RSV-loaded tablets with different infill patterns. Hydroxypropyl methylcellulose acetate succinate and hydroxypropyl cellulose were selected as polymeric carriers to prepare RSV-loaded filaments suitable for FDM printing. The effects of infill pattern on the solid-state characteristics, dimensional accuracy, mechanical properties, floating behavior, and in vitro drug release of the printed tablets were systematically investigated. Differential scanning calorimetry, powder X-ray diffraction, and polarized light microscopy indicated that RSV was mainly converted into an amorphous or molecularly dispersed state after HME and FDM processing. All designed tablets were successfully printed and showed acceptable shape fidelity, while different infill patterns resulted in variations in tablet weight, mechanical strength, floating duration, and release behavior. In vitro dissolution studies showed that the RSV release profiles were dependent on the internal infill architecture. Tablets with more complex infill patterns generally exhibited slower drug release, which may be related to differences in internal pore structure, medium penetration pathways, matrix hydration, and diffusion distance. Release kinetic analysis further suggested that RSV release from the printed tablets involved a combination of diffusion and polymer relaxation processes. These results demonstrate that infill pattern is an important structural parameter for modulating the mechanical performance and drug release behavior of FDM 3D-printed RSV tablets. This study provides useful guidance for the design of 3D-printed oral dosage forms with tunable release characteristics. Full article

The rapid growth in the use of carbon fiber-reinforced polymers (CFRPs) and fused-deposition-modeled (FDM) polylactic acid (PLA) has generated substantial non-biodegradable and thermoplastic waste streams, creating urgent needs for scalable recycling and valorization strategies. This study develops and evaluates an integrated route that chemically recovers carbon fibers (CFs) from CFRP waste and converts them into high-performance reinforcements for recycled PLA matrices. CFRP fragments were pre-swollen in acetic acid (120 °C, 1 h), then depolymerized by means of oxidation with 1 M KMnO₄ (100 °C, 2 h), washed, dried (100 °C, 24 h), and size-reduced by means of cryogenic milling. Recycled CFs (treated) and untreated CFRP fragments were blended with 3D-printing PLA waste at 10, 20 and 30 wt.% via melt mixing (175 °C, 5 min, 70 rpm) and molded into ASTM D638 dog-bone specimens. Materials were characterized via XRD, FTIR, Raman, SEM and mechanical testing. XRD and Raman confirmed retention of the graphitic backbone after treatment; FTIR and Raman revealed oxygen-containing surface functionalization consistent with oxidation, while SEM showed effective removal of epoxy and improved fiber surface cleanliness. Compared with neat PLA (tensile strength 45.4 MPa; modulus 2.6 GPa; elongation 6.3%), composites reinforced with chemically recycled CFs exhibited marked mechanical enhancement: at 30 wt.% treated CF, the tensile strength increased to 102.6 MPa (+126%), elastic modulus to 11.7 GPa (+350%), and toughness to 250.3 MPa, while ductility decreased to 2.9%. Equivalent composites with untreated CFRP exhibited smaller gains (30 wt.%: tensile 87.3 MPa; modulus 10.3 GPa), highlighting the benefit of epoxy removal and surface activation for fiber–matrix adhesion. The proposed chemical recycling pathway is operationally simple and cost-effective, produces reusable CFs with preserved graphitic structure and enhanced surface chemistry, and enables the fabrication of high-performance, waste-derived PLA composites suitable for structural and engineering applications. This work demonstrates a viable waste-to-value approach that advances circularity for both CFRP and 3D-printing polymer waste streams. Full article

Additive manufacturing (AM) enables the fabrication of complex, customisable components from metals, composites and polymers such as polylactic acid (PLA); however, the process commonly produces poor surface finishes and inherent defects. Centrifugal disc finishing (CDF) is an established mass finishing technique in conventional manufacturing but remains insufficiently characterised for additively manufactured polymers. This exploratory study investigates the influence of CDF on fused deposition modelling (FDM)-fabricated PLA components with varying geometrical features, focusing on three-dimensional surface parameters including average areal surface roughness, skewness and kurtosis. Samples were processed up to 720 min with analysis at predetermined intervals to capture transient and steady-state-like behaviour. Surface characterisation was conducted using non-contact optical interferometry to obtain quantitative roughness data and three-dimensional topographical maps, supported by digital optical microscopy and gravimetric analysis to quantify material removal rates. Analysis of the experimental data indicated apparent relationships between processing time, geometry and surface response. Results indicate that material removal behaviour and roughness evolution may be geometry-dependent. Flat and convex surfaces appeared to follow expected transient-like and steady-state-like behaviour, whereas restricted geometries and intricate features exhibited distinct responses with characteristic transition times. Surface roughness reductions ranged from 36% to 89% depending on geometry. These findings provide preliminary quantitative insight into geometry-specific mass finishing behaviour, supporting improved process understanding and informing future optimisation of post-processing strategies for additively manufactured polymer components. Full article

The increasing demand for sustainable and lightweight furniture systems has driven interest in additively manufactured polymer components as alternatives to conventional metal hardware. However, their performance at the functional assembly level under standardized loading conditions remains insufficiently explored. This study evaluates the feasibility of replacing metal drawer slides with fused deposition modeling (FDM)-based polymer alternatives fabricated from polylactic acid (PLA) and polyethylene terephthalate glycol (PETG). Unlike previous studies focused on material-level characterization, this work investigates fully functional drawer slide assemblies integrated into medium-density fiberboard (MDF) systems, enabling component-level assessment under realistic conditions. Specimens were designed in SolidWorks and fabricated under controlled printing parameters. Commercial metal slides were used as benchmarks. Mechanical performance was tested according to BS EN standards, and deformation was measured at multiple points. Statistical analysis included ANOVA, Tukey HSD, and t-tests at a 95% confidence level. Results showed significant differences among materials (p < 0.05). Metal slides exhibited the highest stiffness and minimal deformation. PLA showed stable performance with minor surface degradation, while PETG demonstrated lower dimensional stability and premature failure due to higher compliance. Overall, PLA-based FDM components offer a cost-effective alternative for non-heavy-duty applications, whereas PETG requires further optimization. The study bridges additive manufacturing and real-world furniture component performance under standardized testing. Full article

The increasing demand for high-performance and multifunctional polymer materials has driven interest in improving the mechanical properties of polymer components produced through additive manufacturing. This study aims to systematically investigate and comparatively evaluate the effects of low-content nanofiller incorporation on the structural, thermal, and mechanical performance of PLA-based materials produced via fused deposition modeling (FDM), with a focus on identifying filler-dependent behavior under different loading conditions. In this study, polylactic acid (PLA) composites reinforced with 0.5 wt.% graphene (Gr) and 0.5 wt.% silver (Ag) nanoparticles, added separately, were produced using fused deposition modeling (FDM) and comparatively investigated. Each nanofiller was incorporated individually into PLA-based filaments, and standard test specimens were fabricated via 3D printing. Structural, thermal, and mechanical properties were evaluated using tensile, compressive, and three-point bending tests, along with SEM, EDS, XRD, FTIR, DSC, and TGA analyses. The results showed that pure PLA exhibited typical brittle behavior and a single-stage thermal degradation profile. The tensile strength of pure PLA was 41.93 MPa, and the flexural strength was 70.76 MPa. The addition of 0.5 wt.% graphene led to noticeable improvements, particularly in flexural properties, while only a minimal (almost negligible) increase was observed in tensile strength, with tensile strength increasing to 42.24 MPa (+0.74%) and flexural strength increasing to 110.78 MPa (+56.6%). In contrast, 0.5 wt.% Ag exhibited mixed and load-dependent mechanical behavior, with slight improvements in flexural strength but reductions in tensile and compressive properties, where tensile strength decreased to 22.13 MPa (−47.2%) while flexural strength increased to 112.06 MPa (+58.3%). Structural and thermal analyses indicated that both nanofillers did not significantly alter the PLA matrix chemically, while contributing to controlled changes in material properties primarily through physical interactions. The novelty of this work lies in the comparative evaluation of graphene and silver nanoparticle reinforcement at a fixed low loading level within FDM-processed PLA, combined with a comprehensive and correlated analysis of mechanical, structural, and thermal behavior on the same specimen sets, enabling a clearer understanding of filler-dependent performance mechanisms in additively manufactured nanocomposites. Overall, it was concluded that low-rate nanofiller additions, when properly dispersed, may lead to selective improvements in the performance of PLA-based composites depending on filler type and loading mode, and show potential for advanced engineering applications such as lightweight structural components, functional sensors, and additive-manufactured parts requiring tailored mechanical performance and multifunctionality. Full article

This paper investigates the viability of utilizing Fused Deposition Modeling (FDM) for the fabrication and follow-up testing of a hemispherical resonator (HR). This form of resonator has several significant applications, including the design of vibratory gyroscopes. While traditional high-precision resonators for this application rely on expensive fused-silica fabrication, this study proposes a macro-scale approach using Polylactic Acid (PLA) to enable accessible lab-scale experimentation. The specimens, featuring a unique central-hole mounting configuration, were designed in SolidWorks and analyzed via finite element methods to establish the modal hierarchy. Experimental Modal Analysis (EMA) was conducted using a Laser Doppler Vibrometer (LDV) to acquire vibration signals, which were then analyzed in NVGate, MATLAB, and MEscope to extract natural frequencies and quality factor. Results for a lab-scale HR specimen identified the n = 2 wine-glass mode with a deviation from theoretical natural frequency predictions largely attributed to inherent defects in the fabrication process. Furthermore, a frequency split of 2.15 Hz was observed due to the inherent asymmetries and mass imbalances of the fabrication method. The quality factor was evaluated via the ring-down method and validated using the half-power bandwidth (HPBW) technique. This work demonstrates that 3D-printed resonators serve as an effective, low-cost platform for isolating modal behaviors and optimizing geometric parameters before advancing to micro-scale fabrication. Full article

The qualification of additively manufactured (AM) components produced from engineering polymers poses unique challenges, particularly when evaluating mechanical properties according to ASTM D638. The application of high-performance thermoplastics, such as ULTEM™ 9085 and ULTEM™ 1010, frequently relies on manufacturer-provided datasheets for qualification. However, existing datasheets do not provide guidance specific to articles printed in the XY plane, which can be complicated by failures that initiate at microstructural anomalies rather than being driven by intrinsic material behavior. The objective of this study was to investigate the performance and qualification of ULTEM 9085™, examined according to ASTM D638, and pursue improvements through refined print parameters. A significant improvement in strength and conforming failures was achieved with modest adjustments to the print settings. For Type 1 samples printed with ±45° infill, gage section failures improved from only 5% to 100%, while samples with 0/90° infill achieved 80%. Correspondingly, the ultimate tensile strength increased from 49 ± 2 MPa to 61 ± 2 MPa and from 53 ± 3 MPa to 63 ± 6 MPa, respectively. These results underscore the critical role of process parameters, including contour overlap, in qualifying polymer AM materials, and their contribution to the performance and reliability of printed components. Full article

Additively manufactured cellular architectures frequently exhibit brittle failure under impact due to layer-induced stress concentrations. Through the programming of architectural and material design, specifically combining Fused Deposition Modeling (FDM) lattice topology with hyperelastic polyurea infiltration, this study achieves active control over the macroscopic transition from catastrophic structural fragmentation to stable progressive collapse. To evaluate this, auxetic and honeycomb specimens printed with ABS and glass-fiber-reinforced polyamide (PA-GF) were evaluated in unreinforced and polyurea-infiltrated states under quasi-static compression, three-point bending, and Charpy impact loading. Results show that the compressive response depends primarily on cellular topology; the pure auxetic (A-A) configuration provided the highest stiffness and energy absorption. Polyurea infiltration did not significantly alter elastic stiffness but increased post-yield stability, leading to a 96.6% elastic recovery in PA-GF A-A structures. In flexure, the base polymer governed stiffness, with ABS structures measuring 68% stiffer than PA-GF. Unreinforced ABS achieved 34% higher specific energy absorption (SEA) than PA-GF under compression, with the A-H topology maximizing SEA. Under dynamic impact, PA-GF absorbed an average of 70% more energy than ABS, and the H-A configuration recorded the highest impact resistance. The addition of polyurea shifted the failure mode from brittle fragmentation to stable elastomeric deformation, increasing absorbed impact energy by 52% for ABS and over 30% for PA-GF, preventing catastrophic structural failure. Integrating topological sequencing with elastomeric confinement provides a direct method to control energy dissipation and damage tolerance in 3D-printed cellular composites. Full article

Conventional formwork systems are limited in their ability to efficiently realize complex and free-form concrete geometries, while additive manufacturing (AM)-based formwork faces constraints in casting-stage structural stability and cost-effectiveness, particularly at construction scale. To address these limitations, a hybrid formwork system integrating a structural steel frame with 3D-printed modules is proposed, in which the steel frame resists casting-induced lateral pressure while the printed components define complex mold geometries. The system was fabricated and validated through a full-scale case study structure measuring 3.0 m × 1.7 m × 2.2 m, produced using a large-scale fused deposition modeling (FDM) process with carbon-fiber-reinforced ABS (ABS-CF20). Geometric accuracy was evaluated by comparing design dimensions with as-built measurements across planar, edge, curved, and inclined regions. Construction efficiency and cost performance were assessed through process-based and cost-based comparisons with conventional steel formwork and fully 3D-printed formwork alternatives. The constructed structure reproduced the intended geometry with an average deviation of approximately 3.2 mm and a maximum deviation within ±4 mm, and no notable formwork deformation or damage was observed during concrete casting. Relative to conventional steel formwork, the hybrid system reduced total fabrication duration by about 50% and fabrication cost by about 60% based on a normalized cost index, while also outperforming fully 3D-printed formwork in cost efficiency by about 45%. The modular configuration and bolted connection system further improved transportability, on-site assembly efficiency, and component reusability. These findings demonstrate that the proposed hybrid formwork system provides a practical and resource-efficient pathway for fabricating complex concrete structures, supporting the broader adoption of digital fabrication in sustainable construction practice. Full article

Three-dimensional scaffolds based on triply periodic minimal surfaces (TPMSs) have attracted growing interest in bone tissue engineering because of their high interconnectivity and ability to combine high porosity with mechanical integrity. However, in fused deposition modeling (FDM), printed architecture may systematically deviate from the nominal design, thereby affecting structural fidelity and mechanical performance. This study investigated the influence of FDM processing parameters and nozzle diameter on the effective microarchitecture and compressive elastic modulus of polycaprolactone (PCL) gyroid scaffolds. First, a Taguchi L18 design was used to evaluate the effects of extrusion temperature, printing speed, and flow rate on pore size for two nozzle diameters (0.4 and 0.3 mm). In a second experimental stage, prismatic specimens fabricated at three nominal porosity levels were compression-tested to determine the elastic modulus (E), and measured porosity (ϕ) was quantified by densimetric measurements. A systematic mismatch was observed between the nominal design and the printed scaffold architecture, with both pore size and measured porosity consistently lower than their intended values. The dominant process parameter associated with pore-size variability was nozzle-specific: extrusion temperature contributed most for the 0.4 mm nozzle, whereas printing speed contributed most for the 0.3 mm nozzle. In compression, E decreased with increasing measured porosity, and statistical analysis showed that the E–ϕ relationship was nozzle-dependent. Overall, these findings support a process–structure–property interpretation based on the effective printed microarchitecture rather than on nominal design parameters alone. The experimental stiffness ranges obtained here also provide an exploratory mechanical contextualization relative to reported trabecular bone domains, without implying site-specific scaffold selection. Full article

There is a lack of knowledge concerning the interlaminar fracture toughness of 3D-printed composite materials using both commercial filament composites and fused deposition modeling (FDM) technology from Markforged^®. In this investigation, additive manufacturing (AM) continuous fiber-reinforced thermoplastic (cFRT) specimens have been tested to characterize the initiation and propagation of interlaminar fracture toughness in mode I (G_I). Unidirectional glass fiber (GF)-reinforced polyamide 6 (PA) laminates were characterized by means of the double cantilever beam (DCB) test. These specimens were manufactured using a MarkTwo^® printer and tested without doublers, following a laminate configuration selected according to appropriate experimental findings reported in the state of the art, ensuring reliable fracture characterization. The experimental results exhibited repeatability and strong agreement between the modified compliance calibration (MCC) and modified beam theory (MBT) reduction methods. The resistance curve (R-curve) indicated a progressive increase in fracture resistance during crack propagation. To analyze the experienced failure mechanism during testing, the fracture surfaces of representative post-mortem DCB specimens were observed using a scanning electron microscope (SEM), revealing characteristic morphological features at two magnification levels. Moreover, representative cross-sections of the tested DCB specimens were electronically observed to analyze the interlaminar morphologies, showing an irregular and random distribution of the matrix, fiber, and voids between consecutive plies and adjacent deposited rasters. Compared with previously reported Markforged^® continuous fiber-reinforced systems, the GF/PA composite material exhibited intermediate initiation fracture toughness but lower propagation toughness. This study contributes to filling the existing gap in fracture toughness data for glass fiber-reinforced additively manufactured composites. Full article

This paper presents a practical implementation of a 3D-printed spherical Luneburg lens for gain enhancement of a WR-28 open-ended waveguide antenna operating in the Ka-band. The lens is designed based on Luneburg theory and realized using a six-zone discretized gradient-index structure, providing a balance between theoretical performance and fabrication feasibility. The proposed design enables the realization of the required permittivity distribution using a single dielectric material, where the effective permittivity of each zone is controlled through infill variation in a fused deposition modeling (FDM) process. To facilitate fabrication, the lens is divided into two hemispherical parts, enabling reliable manufacturing and assembly while maintaining the intended dielectric profile. The antenna performance is experimentally evaluated through reflection coefficient (S₁₁) measurements and radiation pattern characterization in both the XZ and YZ planes over the frequency range of 26.5–40 GHz, including co-polarized and cross-polarized responses. The proposed antenna achieves a simulated realized gain ranging from 17.6 dBi to 19.83 dBi, while the measured realized gain ranges from 16.42 dBi to 18.43 dBi, with a maximum deviation of 1.47 dB. In comparison, the standalone WR-28 open-ended waveguide exhibits a measured realized gain of 7.22–8.01 dBi. The integration of the six-zone Luneburg lens results in a realized gain enhancement of 9.20–10.97 dB across the operating band. These results confirm that the proposed approach provides a simple, low-cost, and experimentally validated solution for high-gain millimeter-wave antenna applications, while maintaining good agreement between simulation and measurement. Full article

Flexible thermoplastic polyurethane (TPU) materials fabricated using fused deposition modeling (FDM) are increasingly used in engineering and biomedical applications where exposure to moisture is unavoidable. However, the relationship between material hardness, water absorption, diffusion behaviour, and dimensional stability remains insufficiently understood and investigated. In this study, the hygroscopic behaviour of eight commercially available TPU filaments (60A–98A Shore hardness) was systematically investigated. Specimens were produced using an FDM 3D printer under controlled processing conditions and immersed in physiological solution (0.9% NaCl) for up to 96 h. Water absorption, dimensional changes, and diffusion characteristics were analyzed. Diffusion coefficients were determined using the Fickian diffusion model based on the initial stage of water uptake. The results suggest a transition in behaviour between lower- and higher-hardness materials. Softer TPU materials (60A–85A) exhibited higher water absorption (up to ~1.80%) and an apparent linear trend between hardness and absorption within the investigated material group (R² = 0.999). In contrast, higher-hardness materials (89A–98A) showed lower absorption (~1.18–1.42%) and a weaker apparent relationship with hardness (R² = 0.4214). Diffusion coefficients ranged from 1.40 × 10⁻¹³ to 3.40 × 10⁻¹² m² s⁻¹, with no monotonic dependence on hardness. Additionally, no clear correlation between diffusion kinetics and equilibrium absorption or volumetric expansion was observed. These findings indicate that hygroscopic behaviour of FDM-printed TPU materials cannot be reliably predicted based solely on hardness, and that diffusion, absorption, and swelling may be influenced by different mechanisms. The identified transition from hardness-dependent to behaviour potentially influenced by material structure provides new insight for the design and selection of flexible polymer components in moisture-exposed environments, particularly in biomedical applications. Full article