Search Results (34)

Sea lice have been a persistent pest of the salmon farming industry for more than 50 years. In this study, we aimed to identify if different strains of Atlantic salmon with discrete long-term lice exposure histories had variable resistance to copepodid attachment and/or different attachment-specific transcriptome patterns. We additionally sought to characterize lice distributions on fins, head, and skin and identify if attachment location influenced transcriptomic profiles of lice. Lice counts were correlated with body size and highest on St. John River (SJR; open ocean-run) relative to Grand Lakes Stream (GLS; 200-year restricted ocean-run) or Sebago Lake (CAS; ~11,000 years landlocked) Atlantic salmon. However, lice density was similar between strains. Skin and fins had expectedly different transcriptomic profiles; however, notable differences were not observed between salmon strains. Variance in lice transcriptomes was minimally affected by attachment location even though lice strongly preferred fins relative to head or body. Attached lice did have different transcriptomic profiles on GLS relative to CAS or SJR. This study cumulatively identified a minimal host evolutionary component for sea lice attachment resistance, although lice behavior post-attachment appeared somewhat affected by strain. Non-uniform settlement distributions and tank-specific variability in lice attachment were observed across populations. Full article

This study numerically examines laminar natural convection within a square cavity that has a horizontally attached adiabatic fin on its heated vertical wall. The analysis employed the finite element method to investigate how fin position, length, thickness, and thermal conductivity affect heat transfer behavior over a broad spectrum of Rayleigh numbers (Ra = 10 to 10⁶) and Prandtl numbers (Pr = 0.1 to 10). The findings indicate that the geometric configuration and the properties of the fluid largely influence the thermal disturbances caused by the fin. At lower Ra values, conduction is the primary mechanism, resulting in minimal impact from the fin. However, as Ra rises, convection becomes increasingly significant, with the fin positioned at mid-height (Y_fin = 0.5), significantly improving thermal mixing and flow symmetry, especially for high-Pr fluids. Extending the fin complicates vortex dynamics, whereas thickening the fin improves conductive heat transfer, thereby enhancing convection to the fluid. A new fluid-focused metric, the normalized Nusselt ratio (NNR), is introduced to evaluate the true thermal contribution of fin geometry beyond area-based scaling. It exhibits a non-monotonic response to geometric changes, with peak enhancement observed at high Ra and Pr. The findings provide practical guidance for designing passive thermal management systems in sealed enclosures, such as electronics housings, battery modules, and solar thermal collectors, where active cooling is infeasible. This study offers a scalable reference for optimizing natural convection performance in laminar regimes by characterizing the interplay between buoyancy, fluid properties, and fin geometry. Full article

Floating breakwaters are widely applied on the ocean water surface to protect human infrastructure from the destructive power of waves. This study designs and investigates the performance of a novel symmetric-pontoon floating breakwater with a symmetric pair of hydrofoils. Based at the Cranfield Ocean Systems Laboratory, the system was constructed and tested in various wave conditions using different fin configurations. The floating structure was anchored using a symmetric four-point mooring system. The tested waves were regular and symmetric perpendicular to the propagating direction. Key parameters, including the attenuated wave amplitude, motions of the breakwater, and the mooring forces, were measured. The wave parameters utilised for testing covered 1.61–5.42 relative wavelength to structural length, with wave heights of 3 $\mathrm{c}\mathrm{m}$ and 5 $\mathrm{c}\mathrm{m}$. Results showed the 90° fin configuration can reduce wave transmission by up to 74$\%$, with the lowest mooring forces at 3.05 relative wavelength, enhancing the performance of wave energy dissipation and structural seakeeping. At 90° setup, the mooring force was lowest at 2.41 relative wavelength. This research can inform novel designs of breakwaters to improve protection abilities for coastal cities and offshore infrastructures, especially renewable energy systems. Full article

This study is the first report of parasite and fungal disease separated from domestically reared Atlantic salmon in Korea; the characteristics of the pathogens were identified, and histopathological analysis was conducted. Fungal and parasitic diseases were detected in Atlantic salmon and were isolated as Saprolegnia parasitica and Neoparamoeba perurans based on morphological and genetic analysis. External symptoms observed in Atlantic salmon infected with S. parasitica include fin ulcers and hemorrhage, abdominal hemorrhage, and necrosis of the gills and gill covers. The histopathological analysis results showed necrosis, hemorrhaging, and inflammatory cell infiltration in the abdominal muscles, while only inflammatory cell infiltration was observed in the gill covers. The clinical symptoms observed in Atlantic salmon infected with N. perurans included excessive mucus secretion in the gills, a dense amoebic presence on the gill filaments, respiratory distress, and opening of the mouth and gill covers after death. Through histopathological analysis, we observed lesions in epithelial cells, characterized by the proliferation of epithelial cells and the fusion of secondary lamellae. Numerous lamellae were observed to be attached or fused with each other. To ensure the successful establishment of the Atlantic salmon aquaculture industry in Korea, it is essential to swiftly quarantine infected fish based on the morphological characteristics of S. parasitica and N. perurans revealed in this study, along with the external symptoms of Atlantic salmon infected with these pathogens. Developing disease control strategies based on the findings of this research is imperative. Full article

This opinion piece presents empirical evidence to examine possible negative consequences of the use of penetrative tagging as used on the great white shark (GWS). Tagging programs currently using this method attach SPOT (Spatial Positioning Only Tags) using corrodible bolts inserted through the dorsal fin while the shark is taken out of water. Such methods can cause harm to the tagged individual. Possible adverse effects include impacts on growth, tag biofouling, wounds, heightened stress, and hemorrhaging. This method may adversely impact dorsal fin structure and the shark’s hydrodynamics. As a result, data collected may not be reflective of natural behavior. Bolted SPOT are semi-permanently affixed to the shark but can have a battery life of approximately 3.5 years. Most of these tags (69%) ceased transmitting in less than 2 years. Alternative tagging technologies exist as more humane options. Full article

Virulent Aeromonas hydrophila (vAh) strains that cause motile Aeromonas septicemia (MAS) in farmed channel catfish (Ictalurus punctatus) have been an important problem for more than a decade. However, the routes of infection of vAh in catfish are not well understood. Therefore, it is critical to study the pathogenicity of vAh in catfish. To this goal, a new bioluminescence expression plasmid (pAKgfplux3) with the chloramphenicol acetyltransferase (cat) gene was constructed and mobilized into vAh strain ML09-119, yielding bioluminescent vAh (BvAh). After determining optimal chloramphenicol concentration, plasmid stability, bacteria number–bioluminescence relationship, and growth kinetics, the catfish were challenged with BvAh, and bioluminescent imaging (BLI) was conducted. Results showed that 5 to 10 µg/mL chloramphenicol was suitable for stable bioluminescence expression in vAh, with some growth reduction. In the absence of chloramphenicol, vAh could not maintain pAKgfplux3 stably, with the half-life being 16 h. Intraperitoneal injection, immersion, and modified immersion (adipose fin clipping) challenges of catfish with BvAh and BLI showed that MAS progressed faster in the injection group, followed by the modified immersion and immersion groups. BvAh was detected around the anterior mouth, barbels, fin bases, fin epithelia, injured skin areas, and gills after experimental challenges. BLI revealed that skin breaks and gills are potential attachment and entry portals for vAh. Once vAh breaches the skin or epithelial surfaces, it can cause a systemic infection rapidly, spreading to all internal organs. To our best knowledge, this is the first study that reports the development of a bioluminescent vAh and provides visual evidence for catfish–vAh interactions. Findings are expected to provide a better understanding of vAh pathogenicity in catfish. Full article

This study discussed the effect of ribbed fin, which was suggested by the authors, on the enhancement of heat transfer and flow characteristics of fluid in a solar air heater. The ribbed fin has a rectangular rib at the base and side surfaces of the fin. Thus, it can increase the heat transfer coefficient in the fluid field of a solar air heater as well as extend the heat transfer area. The simulation was performed with various Reynolds numbers, relative heights, and pitches of the rib. The presence of the rib enhances the heat transfer performance by 3.497 times over a smooth fin. However, the addition of the rib also increases pressure drop. Thus, the thermo-hydraulic performance, which considers both heat transfer enhancement and pressure drop increase, was also discussed. Furthermore, this study developed correlations for the Nusselt number and friction factor as a function of geometric condition of the rib and Reynolds number. The correlations accurately predicted the Nusselt number for the base and side surfaces of the fin and friction factor with mean absolute percent errors of 4.24%, 4.53%, and 7.33%, respectively. Full article

Compared to traditional one-sun solar cells, multijunction concentrator cells operating under concentrated solar radiation are advantageous because of their high output and low cooling costs. Such a concentrator PV requires a cooling technique to maintain its performance and efficiency. The performance of a multi-junction concentrator photovoltaic cell of efficiency around 33%, operating under concentrated solar radiation (160–250 sun), has been tested. Heat pipes were used in this study as a fast and efficient way of rejecting heat accumulated in the cells. In this work, the evaporator side of the heat pipe was set in thermal contact with the back side of the solar cell such that the excess heat was transferred efficiently to the other side (condenser side). To positively utilize such excessive heat, two thermoelectric generators were thermally attached to either side of the condenser of the heat pipe, and each was attached to a fin-shaped heat sink. Four different cooling configurations were tested and compared. The net power obtained by this concentrator solar cell employing two types of TEG with different lengths as a cooling alongside two thermoelectric generators for heat-to-electricity conversion was 20% and 17%, corresponding to the long and short heat pipe configurations, respectively, compared to traditional a heat sink only configured at an optical concentration of 230 suns. Full article

Large freshwater mussels (Unionida) are long-lived, have large bodies, and produce thousands to millions of larvae (glochidia) that usually must attach to host fish tissue to complete their life cycle. This is an obligate parasitic stage of mussel larvae. However, less than one in onemillion find a suitable host and survive. The degree of host specificity varies among unionid species, from specialists that can successfully parasitize only one or a few closely related fish species to generalists that can complete development on a taxonomically broad range of fish species. In addition, freshwater mussels are among the most threatened groups of animals. This is due to habitat destruction, the introduction of non-native species, and the loss of host fish on which their larvae (glochidia) are obligate parasites. Glochidiosis harms fish by affecting their growth; on the other hand, freshwater mussels play an important role in freshwaters by improving water quality and ridding the water of bacteria, algae, and pollutants, they are an indicator species of water quality. During our parasitological survey of fish from the Macedonian part of Lake Prespa in April 2022, many glochidia were found on the gills, skin, and fins of two endemic fishes, Prespa roach (Rutilus prespensis) and Prespa nase (Chondrostoma prespense), in the range of tens to thousands on one host. We thus recorded these two endemic species as new hosts of A. cygnea. Full article

Latent heat thermal energy storage (LHTES) technology can alleviate the mismatch between the supply and demand of solar energy and industrial waste heat, but the low thermal conductivity of phase change materials (PCMs) is an issue that needs to be solved. In this work, the effects of the bifurcated fins on melting and solidification are studied, and local and global entropy generation are discussed. The radial lag time and the circumferential lag time were defined to evaluate thermal penetration and thermal uniformity. Subsequently, a novel arc-shaped fin configuration was proposed to further enhance the heat transfer. The results showed that attaching the bifurcated fins could effectively reduce the global entropy generation. Increasing the trunk fin length was beneficial to enhance the thermal uniformity and promote the melting process, while increasing the branch fin was more effective in the solidification process. Overall, thermal uniformity determined the phase change process. More importantly, the concentric arc-shaped fins significantly reduced the heat transfer hysteresis region, showed better thermal performance than straights fins, and the energy storage and release time were reduced by 52.7% and 51.6%, respectively. Full article

The numerical modeling of the effect of wind direction and velocity over the air cooling of PV panels with heat sinks is realized. During the study, a random PV panel with typical characteristics was analyzed for three different wind directions—towards its back, towards its front and from the side. The analysis was realized on a fixed PV panel, oriented to the south, with an inclination of 45 degrees from the horizontal position. The accuracy of the numerical simulation was achieved by comparison with the experimental studies presented in the literature and by comparing the NOCT conditions. The numerical study is focused on different types of heat sinks attached to a typical PV panel. The fins were distributed both horizontally and vertically. A challenging task consisted in simulation of the real wind conditions around the PV panel by taking into account the entire air domain. The simulations were realized for air velocity v_air from 1 m/s to 5 m/s, solar radiation of G = 1000 W/m² and ambient temperature t_air = 35 °C. The output parameters analyzed were the average temperature of PV panels and their power production. Although the lowest temperatures were achieved for the back wind, the cooling effect was more intense for the side wind. The other direction studied also determined the cooling of PV panels. The passive cooling solutions analyzed introduced a rise of maximum power production between 1.85% and 7.71% above the base case, depending on the wind direction and velocity. Full article

In this research, a numerical analysis is accomplished aiming to investigate the effects of adding a new design fins arrangement to a vertical triplex tube latent heat storage system during the melting mechanism and evaluate the natural convection effect using Ansys Fluent software. In the triplex tube, phase change material (PCM) is included in the middle tube, while the heat transfer fluid (HTF) flows through the interior and exterior pipes. The proposed fins are triangular fins attached to the pipe inside the PCM domain in two different ways: (1) the base of the triangular fins is connected to the pipe, (2) the tip of the triangular fins is attached to the pipe and the base part is directed to the PCM domain. The height of the fins is calculated to have a volume equal to that of the uniform rectangular fins. Three different cases are considered as the final evaluation toward the best case as follows: (1) the uniform fin case (case 3), (2) the reverse triangular fin case with a constant base (case 12), (3) the reverse triangular fin case with a constant height (case 13). The numerical results show that the total melting times for cases 3 and 12 increase by 4.0 and 10.1%, respectively, compared with that for case 13. Since the PCM at the bottom of the heat storage unit melts slower due to the natural convection effect, a flat fin is added to the bottom of the heat storage unit for the best case compared with the uniform fin cases. Furthermore, the heat storage rates for cases 3 and 12 are reduced by 4.5 and 8.5%, respectively, compared with that for case 13, which is selected as the best case due to having the lowest melting time (1978s) and the highest heat storage rate (81.5 W). The general outcome of this research reveals that utilizing the tringle fins enhances the thermal performance and the phase change rate. Full article

The dinoflagellate Amyloodinium ocellatum is the etiological agent of a parasitic disease named amyloodiniosis. Mortalities of diseased fish are usually attributed to anoxia, osmoregulatory impairment, or opportunistic bacterial infections. Nevertheless, the phylogenetic proximity of A. ocellatum to a group of toxin-producing dinoflagellates from Pfiesteria, Parvodinium and Paulsenella genera suggests that it may produce toxin-like compounds, adding a new dimension to the possible cause of mortalities in A. ocellatum outbreaks. To address this question, extracts prepared from different life stages of the parasite were tested in vitro for cytotoxic effects using two cell lines derived from branchial arches (ABSa15) and the caudal fin (CFSa1) of the gilthead seabream (Sparus aurata), and for hemolytic effects using erythrocytes purified from the blood of gilthead seabream juveniles. Cytotoxicity and a strong hemolytic effect, similar to those observed for Karlodinium toxins, were observed for the less polar extracts of the parasitic stage (trophont). A similar trend was observed for the less polar extracts of the infective stage (dinospores), although cell viability was only affected in the ABSa15 line. These results suggest that A. ocellatum produces tissue-specific toxic compounds that may have a role in the attachment of the dinospores’ and trophonts’ feeding process. Full article

Subjected to continuous wave loading, the responses of pile foundations and seabed develop gradually, severely affecting the serviceability of piled structures. This paper presents the results of a series of flume experiments on pile foundations in fine sandy and silty seabed under regular wave loading. Pile-head displacement and pore water pressure were measured and the effects of pile diameter, cross-section, pile stiffness and wave height were investigated. The experimental results indicate that the pore pressure in fine sandy seabed varied only slightly even under 640 s of wave loading but showed an increase of 15.7–25.9% around a pile. In silty seabed with much lower permeability, pore pressure accumulated quickly due to piles and oscillated impressively at the depth of soil liquefaction. Based on the comparison between the calculated and measured pile-head displacement, we found that the response of smaller-diameter piles in lower-permeability seabed was much more easily magnified by the induced pore pressure. Increasing the pile diameter and attaching fins could lead to a smaller response of piles. Wave height was a major factor in the experiments that affected the development of response. Full article

As the heat dissipation of smart devices increases, cutting-edge cooling solutions are becoming increasingly important. The heat pipe is an efficient device that boosts heat transfer and is recommended to reduce thermal management power. In this study, a concentric annular heat pipe (CAHP) with distilled water as a working fluid is proposed to enhance heat transfer, and experiments and one-dimensional analysis were carried out to predict thermal characteristics and evaluate performance. The CAHP was 90 mm in length, 62 mm in inner diameter, 70 mm in outer diameter, and 0.4 mm in thickness. At the outer surface of the internal CAHP, a two-layer screen mesh wick (500 mesh, Stainless Steel 304) that is 0.34 mm in layer thickness was installed. A ceramic heater (20 mm × 20 mm) was attached to the middle of the outer surface, and the hollow region with 48 fins was cooled by an electric fan. The experiment was carried out with variations in the heat load, the filling ratio of the working fluid, the pitch angle, the roll angle, and the airflow speed, and the one-dimensional analysis was modeled by AMESIM. The experimental results showed that the best thermal resistance of the CAHP was 3.74 °C/W with a supplied heat of 20 W, a pitch angle of −15°, and a V_air of 3 m/s. In addition, the CAHP’s 1-D simulation model using AMESIM was verified through the experimental results. However, although the modeling results according to the inclination angle could not be reflected due to the difficulty of implementing multiple orientation structures in the one-dimensional simulation model, the simulation results were found to be almost consistent with the experimental results. Case studies were conducted to understand the various characteristics of the CAHP using the model, and the optimal volume fraction, the porosity, and the number of layers of the wicks were determined to be 10, 0.345, and 2, respectively. Full article