Search Results (115)

Introduction: Digital planning and evolution of technology is allowing dentistry to be more efficient in time than before. In orthodontics the main purpose is to obtain fewer patient visits and to reduce the bonding time. For that, indirect bonding planned with CAD-CAM softwares is used to obtain a shorter treatment period, in general, and less chair-time. This waste of chair-time should also be reduced in other fields of dentistry such as endodontics, surgery, prosthodontics, and aesthetics. Methods: A total of 504 teeth were embedded into epoxy resin models mounted as a dental arch. Customized lingual multibracket appliances were bonded by a current adhesion protocol. After that, they were debonded, the polishing of cement remnants was performed with three different burs and two drills. The polishing time of each group was recorded by an iPhone 14 chronometer. Results: Descriptive and comparative statistical analyses were performed with the different study groups. Statistical differences (p < 0.005) between diamond bur and tungsten carbide and white stone burs and turbine were obtained, with the first being the slowest of them. Discussion: Enamel roughness was widely studied in orthodontics polishing protocol as the main variable for protocols establishment. However, in lingual orthodontics, due the difficulty of the access to the enamel surfaces, the protocol is not clear and efficiency should be considered. It was observed that the tungsten carbide bur is the safest bur. It was also recommended that a two-step protocol of polishing by tungsten carbide bur be followed by polishers. Conclusions: A tungsten carbide bur mounted in a turbine was the most efficient protocol for polishing after lingual bracket debonding. Full article

This paper presents the development and analysis of a planar microfluidic microwave sensor featuring three circular complementary split-ring resonators (CSRRs) fabricated on an RO3035 substrate. The sensor demonstrates enhanced sensitivity in characterizing liquids contained in a fine glass capillary tube by leveraging a novel configuration: a central 5-split-ring CSRR with a drilled hole to suspend the capillary, flanked by two 2-split-ring CSRRs to improve the band-stop filtering effect. The sensor’s performance is benchmarked against another CSRR-based microwave sensor with a similar configuration. High linearity is observed (R² > 0.99), confirming its capability for precise ethanol concentration prediction. Compared to the replicated square CSRR design from the literature, the proposed sensor achieves a 35.22% improvement in sensitivity, with a frequency shift sensitivity of 567.41 kHz/% ethanol concentration versus 419.62 kHz/% for the reference sensor. The enhanced sensitivity is attributed to several key design strategies: increasing the intrinsic capacitance by enlarging the effective area and radial slot width to amplify edge capacitive effects, adding more split rings to intensify the resonance dip, placing additional CSRRs to improve energy extraction at resonance, and adopting circular CSRRs for superior electric field confinement. Additionally, the proposed design operates at a lower resonant frequency (2.234 GHz), which not only reduces dielectric and radiation losses but also enables the use of more cost-effective and power-efficient RF components. This advantage makes the sensor highly suitable for integration into portable and standalone sensing platforms. Full article

Faults and fracture sets in carbonate reservoirs are key geological features that govern hydrocarbon migration, accumulation, and wellbore stability. Their accurate detection is essential for structural interpretation, reservoir modeling, and drilling risk assessment. In this study, we propose an Optimally Oriented Coherence Attribute (OOCA) method that integrates geological guidance with multi-frequency structural analysis to achieve enhanced sensitivity to faults and fractures across multiple scales. The method is guided by depositional and tectonic principles, constructing model traces along directions with maximal structural variation to amplify responses at geological boundaries. A distance-weighted computation and extended directional model trace strategy are adopted to further enhance the detection of fine-scale discontinuities, overcoming the limitations of traditional attributes in resolving subtle structural features. A Gabor-based multi-frequency fusion framework is employed to simultaneously preserve large-scale continuity and fine-scale detail. Validation using physical modeling and field seismic data confirms the method’s ability to enhance weak fault imaging. Compared to traditional attributes such as C3 coherence, curvature, and instantaneous phase, OOCA delivers significantly improved spatial resolution. In zones with documented lost circulation, the identified structural features align well with drilling observations, demonstrating strong geological adaptability and engineering relevance. Overall, the OOCA method offers a geologically consistent and computationally efficient solution for high-resolution fault interpretation and drilling risk prediction in structurally complex carbonate reservoirs. Full article

Wellbore instability is a major constraint in large-scale shale oil extraction. This study focuses on the shale–sandstone interbedded shale oil reservoirs in the Chang 7 area, delving into the evolutionary principles governing wellbore stability in horizontal drilling operations within these formations. A geological feature analysis of shale–sandstone reservoir characteristics coupled with rigorous mechanical experimentation was undertaken to investigate the micro-mechanisms underpinning wellbore instability. The Mohr–Coulomb failure criterion applicable to sandstone and the multi-weakness planes failure criterion of shale were integrated to analyze the stress distribution of surrounding rocks within horizontal wells, facilitating the computation of collapse pressure and fracture pressure. A finite element model of wellbore stability in shale–sandstone horizontal drilling was established, and then we conducted a comprehensive analysis of the impacts of varying elastic moduli, Poisson’s ratio, and in-situ stress on wellbore stability. The findings reveal that under varying confining pressures, the predominant failure mode observed in most sandstone samples is characterized by inclined shear failure, coupled with a reduced incidence of crack formation. The strength of shale escalates proportionally with increasing confining pressure, resulting in a reduced susceptibility to failure along its inherent weak planes. This transition is characterized by a gradual shift from the prevalent mode of longitudinal splitting towards inclined shear failure. As the elastic modulus of shale rises, the discrepancy between circumferential and radial stresses decreases. In contrast, with the increasing elastic modulus of sandstone, the gap between circumferential and radial stresses widens, potentially inducing potential instabilities in the wellbore. An increase in sandstone’s Poisson’s ratio corresponds to a proportional increase in the difference between circumferential and radial stresses. Under reverse fault stress regimes, wellbore collapse and instability are predisposed to occur. Calculations of collapse pressure and fracture pressure reveal that the safety density window is minimized at the interface between shale and sandstone, rendering it susceptible to wellbore instability. These research findings offer significant insights for the investigation of wellbore stability in interbedded shale–sandstone reservoirs contributing to the academic discourse in this field. Full article

This study examines the distribution of pore pressure (PP) and fracture gradient (FG) within intervals of lost circulation encountered during drilling operations in the Ordovician reservoir (IV-3 unit) of the Tin Fouye Tabankort (TFT) field, located in the Illizi Basin, Algeria. The research further aims to determine an optimized drilling mud weight to mitigate mud losses and enhance overall operational efficiency. PP and FG models for the Ordovician reservoir were developed based on data collected from five vertical development wells. The analysis incorporated multiple datasets, including well logs, mud logging reports, downhole measurements, and Leak-Off Tests (LOTs). The findings revealed an average overburden gradient of 1.03 psi/ft for the TFT field. The generated pore pressure and fracture gradient (PPFG) models indicated a sub-normal pressure regime in the Ordovician sandstone IV-3 reservoir, with PP values ranging from 5.61 to 6.24 ppg and FG values between 7.40 and 9.14 ppg. The analysis identified reservoir depletion due to prolonged hydrocarbon production as the primary factor contributing to the reduction in fracture gradient, which significantly narrowed the mud weight window and increased the likelihood of lost circulation. Further examination of pump on/off cycles over time, coupled with shallow and deep resistivity variations with depth, confirmed that the observed mud losses were predominantly associated with induced fractures resulting from the application of excessive mud weight during drilling operations. Based on the established PP and FG profiles, a narrow mud weight window of 6.24–7.40 ppg was recommended to ensure the safe and efficient drilling of future wells in the TFT field and support the sustainability of drilling operations in the context of a depleted reservoir. Full article

This narrative review explores the significant evolution of sports rehabilitation, tracing its trajectory from basic exercise therapies of the early 20th century to the advanced, neuroplasticity-driven approaches of the 21st century, with a specific focus on anterior cruciate ligament reconstruction (ACLR). The primary aim is to understand how neuroplasticity, motor control, and sensorimotor retraining can optimize recovery, reduce reinjury risk, and enhance long-term athletic performance, and to synthesize current rehabilitation strategies that integrate innovative technologies, such as robotics, virtual reality (VR), and biofeedback systems, to address the neurocognitive deficits that contribute to the alarmingly high reinjury rates (9–29%) observed in young athletes post-ACLR. These deficits include impaired proprioception, motor control, and psychological factors like fear of reinjury. The methodology employed involves a narrative review of peer-reviewed literature from databases including PubMed, Scopus, and Web of Science. The synthesis of findings underscores the importance of holistic rehabilitation approaches, including targeted proprioceptive exercises, dual-task drills, and immersive VR training, in enhancing sensorimotor integration, decision-making, and athlete confidence. Furthermore, this review highlights the critical need for long-term monitoring and interdisciplinary collaboration between neuroscientists, physiotherapists, and engineers to refine rehabilitation protocols and ensure sustained recovery. By leveraging neuroplasticity and advanced technologies, the field can shift from a focus on purely physical restoration to comprehensive recovery models that significantly reduce reinjury risks and optimize athletic performance. Full article

Hydraulic fracturing is a crucial technology for resource development, such as shale gas, and its optimization is necessary to enhance development efficiency. However, evaluating fracture shapes involves technical uncertainties. Japan Organization for Metals and Energy Security (JOGMEC) and Kyoto University have conducted laboratory-scale hydraulic fracturing experiments using coagulable fluorescent resin as the injection fluid (resin fracturing test) to visualize hydraulic fractures and investigate their relationship with acoustic emissions (AEs) generated during fracturing. Since lab-scale experiments can only examine the phenomena near the injection hole owing to size limitations, we designed an experiment to apply the visualization method to the outcrop scale. This paper presents the results from an in situ, outcrop-scale hydraulic fracturing experiment conducted at the Kamioka Mine, Gifu Prefecture, Japan, from 2022 to 2023, with goals similar to those of the laboratory experiments. A resin fracturing borehole (RF1) with a diameter of 76 mm was core-drilled to a depth of approximately 10 m for the resin fracturing tests. AEs were observed in five boreholes drilled around RF1 at the same depth. Resin fracturing tests were performed at two different depths, with breakdown confirmed at both. A core of a larger diameter (205 mm) was recovered by coaxial overcoring around RF1, and resin-filled fractures were observed under black light on the core surfaces. After the resin fracturing experiment, two analyses were performed using the acquired core and AE data to predict the fracture extension and the mechanism of AE occurrence. We compared the distribution of AE events and visualized fractures in the core. Additionally, we compared the stress direction estimated from failure mechanism analysis using AE data with the maximum stress direction estimated from hydraulic fracturing. Our analysis provided several insights into fracture extension. The distribution of AE hypocenters was consistent with the direction of the hydraulic fractures confirmed by coring after the resin fracturing test. The failure mechanisms are classified based on the polarity of the first P-wave motion of the AE waveform. However, the actual scale of oil fields is significantly larger than that considered in this study. Discussing visible fractures created by hydraulic fracturing is deemed meaningful. We expect that the results of this study will provide valuable information for the precise estimation of hydraulic fractures. Full article

A combination of theoretical analysis, numerical simulation and physical model experiments is used to explore the mechanism of pressure relief and roof blasting effects along the gob-side roadway. The stress and displacement along the gob-side roadway before and after blasting were investigated using discrete unit code (UDEC) software. The results demonstrated that blasting can effectively decrease the peak stress of the coal seam along the gob-side roadway and transfer it to the depth. The maximum displacement of the roof of the gob-side roadway, the coal pillar and the solid coal was reduced from 9.5, 10.8 and 4 cm to 6.5, 2 and 3 cm, respectively, after roof blasting. The experimental results showed that the movement of the overburden strata showed obvious regional characteristics after blasting which included the height of the caving zone on the broken side being 3.3 times higher than that observed on the unbroken side, while the height of the fractured zone was 0.52 times higher. The field application of roof blasting was controlled by a drilling method, micro-seismic monitoring and stress monitoring. The results showed good application effects. This research provides valuable insights for managing the stability of gob-side entries. Full article

Three-dimensional (3-D) magnetic inversion is an essential technique for revealing the distribution of subsurface magnetization structures. Conventional methods are often time-consuming and suffer from ambiguity due to limited observations and non-uniqueness. To address these limitations, we propose a novel inversion method under the machine learning framework. First, we design a training sample generation space by extracting the horizontal positions of magnetic sources from the analytic signal amplitude and the reduced-to-the-pole anomalies of magnetic field data. We then employ coordinate transformation to achieve data augmentation within the designed space. Subsequently, we utilize a broad learning network to map the magnetic anomalies to 3-D magnetization structures, reducing the magnetic inversion time. The efficiency of the proposed method is validated through both synthetic and field data. Synthetic examples indicate that compared to the traditional inversion method, the proposed method approximates the true model more closely. It also outperforms traditional and deep learning methods in terms of computational efficiency. In the field example of the Danzhukeng Pb-Zn-Ag deposit in South China, the inversion result is consistent with drilling and controlled-source audio frequency magnetotelluric survey data, providing valuable insights for subsequent exploration. This study provides a new practical tool for processing and interpreting magnetic anomaly data. Full article

As mining depths increase, the highly metamorphosed anthracite in Southwest China progressively develops into a complex dynamic disaster influenced by both in situ stress and gas pressure. By utilizing characteristic indicators of mining-induced stress and gas dynamic emissions, a grading evaluation method for coal and gas dynamic disasters (CGDDs) based on fuzzy mathematics l theory is proposed and validated at the No. 1 Well of the Yuwang Coal Mine. The results indicate that the acceleration of microseismic wave velocity and the increase in the wave velocity anomaly coefficient are indicative of a more pronounced stress concentration. The working face exhibits distinct gradations of stress concentrations, categorized as weak, moderate, and strong. Moreover, the increase in microseismic wave velocity and the anomaly coefficient further confirm the intensity of the stress concentrations. Gas dynamic emissions show a clear correlation with the drill cuttings gas desorption indicator ($K_1$ value) and drill cuttings volume ($S$ value). Characteristic indicators A, B, and D are suitable for assessing the risk of CGDDs in the working face. For the application of individual indicators for classifying the CGDD risk at different distances from the crosscut (128 m, 247.5 m, 299.4 m, and 435 m) in the 1010201-working face, contradictory classification results were observed. However, the classification results derived from the fuzzy mathematics method were consistent with the findings of field investigations. As the working face advanced through the pre-concentrated stress zone, significant changes were observed in both the source wave velocity and wave velocity anomaly coefficient. Concurrently, gas emissions displayed a distinct pattern of fluctuation characterized by increases and decreases. The consistency between the periodic weighting of the working face, the gas emission, the drill cuttings gas desorption indicator, and the stress field inversion result further validates the classification outcomes. These research results can provide theoretical support for the monitoring of CGDDs. Full article

In the exploitation of deep geothermal energy from hot dry rock (HDR) reservoirs, traditional drilling methodologies exhibit a retarded penetration rate, posing a significant impediment to efficient energy extraction. The fluidic DTH hammer is recognized as a drilling method with potential in hard formations. However, a low energy utilization was observed due to the substantial fluid loss in the fluidic oscillator (the control component of a fluidic hammer). In order to reduce the energy loss and improve the performance of fluidic hammers, a fluidic oscillator with a deflector structure is proposed in this paper. Utilizing Computational Fluid Dynamics (CFD) simulations, the optimal structural parameters for the deflector structure have been delineated, with dimensions specified as follows: a = 13.5 mm; b = 2.0 mm; and c = 2.2 mm. Subsequently, the flow field and the performance were observed. The maximum flow recovery of the output channel of the deflector structure increased by 9.1% in the backward stroke and 3.6% in the forward stroke. Moreover, the locking vortex range is expanded upward, which improves the wall attachment stability of the main jet. Finally, to substantiate the numerical findings and evaluate the practical efficacy of the deflector structure, a series of bench tests were conducted. According to the results, compared with the original structure, the average impact frequency can be increased by 5.8%, the single average impact energy increased by 7.5%, and the output power increased by 13.8%. Full article

Used for soil and weathered rocks, soil nails are rigid reinforcements positioned at certain angles on the ground to provide slope stability. A rigid reinforcement element placed in a well filled with cement grout mix after completing drilling will generate adherence stress between the grout-mixed nail bar and soil. Due to this stress, load is transferred to the soil along the soil–grout interaction surface. In the case discussed herein, the slope at the parcel border needed to be made steeper in order to accommodate the construction of a facility in the Taşkısığı region of Sakarya province. Soil-nailed walls, which are inexpensive and suitable for weathered rocks, were needed as a support system because the slope was too steep to support itself. Support system performance was measured using two inclinometers and two soil nail pull-out tests conducted on different sections observed during and after construction. Contrary to the design-phase prediction, it was determined that the stresses started to dampen in the region closer to the slope-facing zone. Field measurement data and numerical analysis revealed that higher parameters than necessary were selected. In this context, sensitivity and parameter analyses were carried out using the Hoek–Brown constitutive model. The GSI value was re-evaluated and found to be compatible with the observation results obtained from the field performance. Since the retaining wall performance observed was higher than expected, geometric parametric analysis of the structural elements was performed; high safety coefficients were found across variations. The effects of the inclination of the slope, nail length, nail spacing, and nail slope design parameters on the safety coefficient and horizontal displacement were examined. The optimal design suggested nail lengths of 4.00 m, a spacing of 1.60 m, and slopes of 20°. It was discovered that the effect of the inclination degree of the slope on the safety coefficient was lower than expected. The results revealed that a more economical design with a similar safety factor can be obtained by shortening the lengths of the nails. Full article

The sampling and observation of subglacial lakes play a vital role in studying the physical and chemical properties as well as the microbial characteristics of water within these Antarctic subglacial lakes. Compared to existing techniques, such as deep ice core drilling and clean hot water drilling, recoverable autonomous sondes, inspired by the spinning and reeling silk behavior of spiders, offer several advantages, including lightweight design, low power consumption, and minimal external pollution. Over the past six years, Jilin University, with support from the Ministry of Science and Technology of China, has developed an environmentally friendly sampling and observation system for Antarctic subglacial lakes, utilizing a recoverable autonomous sonde. The whole system includes a melting sonde, detection and control unit, scientific load platform, and ice surface auxiliaries. Extensive laboratory and joint system tests were conducted, both on key components and the complete system, including field tests in ice lakes. The results of these tests validated the feasibility of the underlying principles, the long-term reliability of the system operation, and the cleanliness of the drilling process. Ice penetration speed up to 2.14 m/h was reached with 6~6.5 kW melting tip power and a 660 mL lake water sample was collected. The relevant design concepts and technologies of the system are expected to play an important role in the clean detection and sampling of subglacial lakes in Antarctica, Greenland, and other regions. Full article

Shallow gas, with huge resources, has been confirmed using three dimensional (3D) seismic data and more than 20 drilling sites in the deep water of the LS36 gas field, the Qiongdongnan Basin, the South China Sea. The interface of sedimentary facies in the southern boundary of the basin controls the distribution within the basin of clastic sediments coming from the north and west of the land uplifted. In this study, seismic data and geophysical attributes were used to investigate the controlling effect of the interface of sedimentary facies on the distribution of shallow gas within the basin. Our study shows that the shallow gas is mainly distributed in the Quaternary Ledong Formation in the southwest of the Qiongdongnan Basin, which was observed from acoustic impedance, amplitude versus offset (AVO), and seismic interpretations. The channelized submarine fans that onlap the interface of the sedimentary facies are distributed in a vertically stacked manner and are the main reservoirs for the shallow gas. Therefore, these sedimentary studies show that the sand-rich sediments are distributed along the interface of the sedimentary facies from the southwest to the northeast and are limited to the shallow gas within the basin. The Central Canyon provides an important deep gas source, while the flank of the canyon, gas chimney, and normal faults related to basement uplift provide pathways for vertical and lateral gas migration to form the shallow gas. This study shows that shallow gas may be widely distributed in other marginal sea basins, and sedimentary systems should be further studied in the future. Full article

High-density oil-based drilling fluids (OBDFs) are widely used in drilling operations, but during their application, the viscosity of the fluid typically increases due to the enhancement of the solid-phase gel network structure. This can lead to issues such as impaired fluid circulation, increased blowout risks, and accelerated drill bit wear. In this study, a compound (OCD), synthesized from tall oil fatty acids, diethylene triamine, and maleic anhydride, was developed to disrupt the strong gel structure in high-density OBDFs, thereby reducing the viscosity of the OBDFs. Rheological properties, including viscosity, yield point, and gel strength, were tested to evaluate the viscosity-reducing effect of OCD on both laboratory-prepared and field high-density OBDFs. Additionally, the effects of OCD on electrical stability (ES), high-temperature high-pressure (HTHP) filtration loss, and solid-phase settling stability were also tested. Finally, the mechanism of OCD was analyzed through contact angle tests, particle size analysis, and microstructural observations. The experimental results demonstrated that OCD could effectively reduce the viscosity of various high-density OBDFs. Adding 2 wt% of OCD reduced the apparent viscosity of laboratory-prepared OBDFs by 20.4%, and reduced the apparent viscosity of field OBDFs with a density of 1.7 g/cm³ by 29.2%. Furthermore, OCD showed good compatibility with OBDFs, having negligible effects on HTHP filtration loss and ES, and maintained good viscosity-reducing performance even at 180 °C. Mechanistic studies revealed that OCD enhanced the hydrophobicity of the solid phase, reduced the particle size of solids, and prevented the formation of excessive network structures in the oil. Therefore, this study provides significant practical value for controlling the rheological performance of the gel system in OBDFs. Full article