Search Results (69)

Fiber Bragg Grating (FBG) sensors are widely used for strain and temperature monitoring due to their high sensitivity, compact size, electromagnetic immunity, and multiplexing capability. While conventional FBG interrogators remain bulky and costly, Photonic Integrated Circuit (PIC) platforms provide a promising route toward compact, scalable, and low-power FBG interrogation. However, the choice of architecture strongly determines the achievable resolution, bandwidth, multiplexing capacity, and robustness. This review compares on-chip demodulation architectures, evaluating their performance in resolution, bandwidth, and interrogation speed. We show that the optimal architecture depends strongly on the application: AWG-based schemes excel in compact, multi-FBG readout; ring-resonator systems are highly effective for tunable filtering; and interferometric phase-domain schemes offer the highest sensitivity for dynamic strain sensing. Despite these architectural advances, practical deployment remains constrained by system-level bottlenecks. These challenges primarily include source/detector integration, fiber–chip coupling, packaging robustness, and thermal drift. Overcoming these barriers requires a shift in future development from isolated photonic-device optimization toward comprehensive, system-level co-design. Full article

To address the need for high electrical insulation, strong immunity to electromagnetic interference, and miniaturized AC electrical-signal detection in complex electromagnetic environments, we propose and experimentally demonstrate a fiber-optic sensor based on a piezoelectric ceramic (PZT)-driven ring tapered-fiber resonator. The applied AC excitation is converted into periodic mechanical deformation through the inverse piezoelectric effect of the PZT, and the resulting strain modulates the resonator response, enabling optical demodulation of the input frequency and amplitude. A comprehensive figure of merit was introduced to optimize the tapered-fiber geometry, yielding an optimal waist diameter of approximately 10 μm. The sensor can effectively distinguish both single- and dual-frequency AC signals. Over the range of 50–500 Hz, the demodulated frequency agrees closely with the input frequency, with a linear fitting coefficient of 0.9999. At a fixed driving frequency of 250 Hz, the amplitude of the characteristic spectral peak increases nearly linearly with the input voltage amplitude, with a fitting coefficient of 0.9945. The device also exhibits good stability over 30–150 °C and during 70 h of continuous operation. With its simple structure, low cost, and strong immunity to electromagnetic interference, this sensor provides a practical solution for AC electrical-signal detection in complex environments. Full article

This paper provides a comprehensive overview of the progress in fiber-optic gyroscope technology, covering 260 key studies of the last ten years. A critical comparative analysis of fiber-optic gyroscope with alternative inertial sensors (Micro-Electro-Mechanical Systems, Hemispherical Resonator Gyroscope, Ring Laser Gyroscope) has been carried out. Confirming the unique advantages of fiber-optic gyroscope for autonomous navigation. Fundamental limitations of accuracy are considered in detail: temperature drifts, polarization noise, and Rayleigh backscattering. Modern hardware methods for suppressing these errors, including the use of photonic crystal and hollow fibers (Air-Core/Hollow-Core), are also considered in this work. The central place in the review is occupied by the analysis of the technological paradigm shift from bulky discrete circuits to hybrid integrated photonics (Indium Phosphide, Silicon Nitride, Lithium Niobate) and hybrid architectures to reduce weight and size characteristics. The role of artificial intelligence (Deep Learning, Long Short-Term Memory) methods in nonlinear drift compensation and calibration is discussed. The usage of the Brillouin effect and optomechanics promising areas are outlined, necessary to create a new generation of navigation systems operating in the absence of Global Navigation Satellite Systems signals. Full article

In response to the key issues of complex internal structure, significant attenuation of partial discharge (PD) ultrasound signal propagation, and low sensor sensitivity in large oil–immersed power transformers, this paper analyzes the multi–order resonant mode vibration characteristics of the shaft–type fiber optic ultrasound sensor core structure. The displacement distribution patterns of the core structure in both transverse and longitudinal resonant modes are clarified. A strategy using oblique fiber winding rings is proposed to eliminate the problems of strain cancellation and non–accumulation of displacement in transverse and longitudinal resonant modes, which are common in traditional fiber optic ultrasound sensors with parallel fiber windings. Furthermore, design principles are provided to enhance the coverage of the free end and the high–strain regions with semi–high symmetry, as well as the vector–integrated response suitable for multi–order modes. Experimental results show that, in typical PD model detection, the oblique winding sensor exhibits a more prominent response near the high–order resonances of the core, with a detection sensitivity approximately 2.5 times higher than that of the parallel winding structure, and an overall sensitivity at least 7.4 times greater than that of traditional Piezoelectric (PZT) sensors. This demonstrates that the fiber winding method is a key design parameter determining the acoustic–solid coupling efficiency and high sensitivity performance of shaft–type fiber optic interferometric PD sensors, providing a feasible path for high–reliability fiber optic sensing solutions for online monitoring of transformer partial discharges. Full article

We propose an external-cavity laser that combines wide tunability with narrow linewidth. The design utilizes a low-loss Si₃N₄ waveguide and a thermally tuned cascaded triple-ring resonator to enable continuous wavelength tuning. The numerical simulations indicate that the proposed laser exhibits a tuning range of 64 nm with a sub-kHz linewidth, an SMSR of more than 80 dB, an output power of 24 mW and a linewidth of 193 Hz at 1550 nm. Furthermore, we perform comparative system-level simulations using QPSK and 16QAM coherent optical fiber links at 50 Gbaud over 100 km. Under identical conditions, when the laser linewidth is reduced from 1 MHz level to 193 Hz, the BER of 16QAM decreases from 1.5 × 10⁻³ to 5.3 × 10⁻⁵. These results indicate that a narrow linewidth effectively mitigates phase noise degradation in high-order modulation formats. With its narrow linewidth, wide tuning range, high SMSR, and high output power, this laser serves as a promising on-chip light source for high-resolution sensing and coherent optical communications. Full article

Achieving controllable wavelength tuning in optofluidic whispering gallery mode microcavity lasers is crucial for high-throughput, multi-sample, multiplexed biochemical sensing and multifunctional integrated photonic devices. This paper develops a bidirectionally wavelength-tunable optofluidic fiber whispering gallery mode microcavity laser driven by Rhodamine 6G co-doped with different acceptor dyes. Experimentally, a thin-walled silica ring inside a hollow-core anti-resonant fiber served as the optical microcavity, with a fixed 2.5 mM Rhodamine 6G co-doped with other dyes as the gain medium. The results revealed that when co-doped with Rhodamine B or Cy3, the single-longitudinal-mode laser emission wavelength exhibited a red shift with increasing co-dopant concentration. Conversely, when co-doped with Cy5, the laser output wavelength showed a distinct blue shift. This unique bidirectional tuning characteristic originates from the different fluorescence resonance energy transfer efficiencies between the co-dopants and Rhodamine 6G, and their competitive modulation of the system’s effective gain spectrum. The study offers a novel and flexible strategy for achieving wide-range, controllable wavelength tuning on a single laser platform, with significant potential for applications in biochemical sensing and multifunctional integrated photonic devices. Full article

To address the issues of limited orbital angular momentum (OAM) mode count, poor transmission quality, and complex cladding structures in ring-core photonic crystal fibers, a novel OAM-supporting ring-core anti-resonant photonic crystal fiber is designed. This fiber features a high-index-doped ring-core surrounded by a three-layer anti-resonant nested tube cladding. Numerical simulations based on the finite element method indicate that the designed fiber has the ability to reliably transmit up to 90 OAM modes within the wavelength range of 1530–1620 nm. Additionally, this fiber demonstrates outstanding performance characteristics, achieving a peak effective refractive index difference of 0.0041 while maintaining remarkably low confinement loss between 10⁻¹² dB/m and 10⁻⁸ dB/m. The minimum effective mode field area is 101.41 μm², and the maximum nonlinear coefficient is 1.05 W⁻¹·km⁻¹. The dispersion is flat, with a minimum dispersion variation of merely 0.5394 ps/(nm·km). The mode purity is greater than 98.5%, and the numerical aperture ranges from 0.0689 to 0.089. The designed OAM-supporting ring-core anti-resonant photonic crystal fiber has broad application prospects in long-haul optical communication and high-speed data transmission. Full article

Narrow-linewidth semiconductor lasers have become indispensable devices in high-precision measurement and detection. Among various available technologies, self-injection locking plays a crucial role due to its significant ability to reduce linewidth and enhance coherence. Here, we demonstrate a hybrid feedback narrow-linewidth laser based on fixed external cavity feedback combined with self-injection locking feedback. The laser consists of a semiconductor gain chip, fiber Bragg grating, and micro-ring resonator, achieving laser mode selection and linewidth compression. Ultimately, a single longitudinal mode narrow-linewidth laser output with a Lorentzian linewidth of 149 Hz and a side-mode suppression ratio of 65 dB was obtained. The demonstrated laser can be applied in applications such as coherent optical communication and high-precision coherent detection. Full article

This study innovatively presents a hollow-core anti-resonant fiber integrating double-tube nesting and a single-layer anti-resonant wall. Featuring an exclusive two-layer cladding configuration along with an outer cladding circular ring, it differs significantly from traditional fibers. After careful parameter optimization, at 1.55 μm wavelength, the fiber shows excellent performance. Its confinement loss drops to 0.00088 dB/km, 1–2 orders lower than traditional ones. The proportion between the loss of the lowest higher-order mode and that of the fundamental mode reaches 19,900, indicating excellent single-mode performance. In the case of a bending radius of 11–14.2 cm, the x-polarization loss is below 0.001 dB/km, showing good bending resistance. Through structural comparisons, this paper quantitatively reveals the effects of the anti-resonant wall, cladding tube, and outer cladding ring on fiber performance. From the practical fiber-drawing process, it thoroughly analyzes the impact of the outer connecting tube’s offset angle on fiber performance. This research provides crucial theoretical support for new hollow-core fiber design, manufacture, and application, and is expected to drive technological innovation in this field. Full article

We propose a simple and innovative configuration consisting of a quantum dot and micro-optical resonator that emits single photons with good directionality in a plane parallel to the substrate. In this device, a single quantum dot is placed as a light source between the slits of a triangular split-ring micro-optical resonator (SRR) supported in an optical polymer film with an air-bridge structure. Although most of the previous single photon emitters in solid-state devices emitted photons upward from the substrate, operation simulations confirmed that this configuration realizes lateral light emission in narrow regions above, below, left, and right in the optical polymer film, despite the absence of a light confinement structure such as an optical waveguide. This device can be fabricated using silica-coated colloidal quantum dots, focused ion beam (FIB) lithography, and wet etching using an oxide layer on a silicon substrate as a sacrificial layer. The device has a large tolerance to the variation in the position of the SRR in the optical polymer film and the height of the air-bridge. We confirmed that Pt-SRRs can be formed on the optical polymer film using FIB lithography. This simple lateral photon emitter is suitable for coupling with optical fibers and for fabricating planar optical quantum solid-state circuits, and is useful for the development of quantum information processing technology. Full article

A Hz level narrow linewidth all-optical microwave oscillator based on the torsional radial acoustic modes (TR_2,m) of a single-mode fiber (SMF) is proposed and validated. The all-optical microwave oscillator consists of a 20 km SMF main ring cavity and a 5 km SMF sub ring cavity. The main ring cavity provides forward stimulated Brillouin scattering gain and utilizes a nonlinear polarization rotation effect to achieve TR_2,7 mode locking. By combining the sub ring cavity with the main ring cavity and utilizing the Vernier effect, the TR_2,7 mode microwave photonic single longitudinal mode (SLM) output can be ensured. Meanwhile, the 6.281 Hz narrow linewidth of the TR_2,7 mode is achieved by reducing the intrinsic linewidth of the passive resonant cavity. The acoustic mode suppression ratio and side mode suppression ratio of the TR_2,7 mode were 43 dB and 54 dB, respectively. The power and frequency fluctuations of within 40 min were approximately ±0.49 dB and ±0.187 kHz, indicating good stability. At a frequency offset of 10 kHz, the TR_2,7 mode had a low phase noise value of −110 dBc/Hz. This solution can be used in various fields, such as high-precision radar detection, long-distance optical communication, and high-performance fiber optic sensing. Full article

With the rapid advancement of information technology, the data demands in transmission rates, processing speed, and storage capacity have been increasing significantly. However, silicon electro-optic modulators, characterized by their weak electro-optic effect, struggle to balance modulation efficiency and bandwidth. To overcome this limitation, we propose an electro-optic modulator based on an all-fiber micro-ring resonator and a p-Si/n-ITO heterojunction, achieving high modulation efficiency and large bandwidth. ITO is introduced in this design, which exhibits an ε-near-zero (ENZ) effect in the communication band. The real and imaginary parts of the refractive index of ITO undergo significant changes in response to variations in carrier concentration induced by the reverse bias voltage, thereby enabling efficient electro-optic modulation. Additionally, the design of the all-fiber micro-ring eliminates coupling losses associated with spatial optical-waveguide coupling, thereby resolving the high insertion loss of silicon waveguide modulators and the challenges of integrating MZI modulation structures. The results demonstrate that this modulator can achieve significant phase shifts at low voltages, with a modulation efficiency of up to 3.08 nm/V and a bandwidth reaching 82.04 GHz, indicating its potential for high-speed optical chip applications. Full article

In the last decade, substantial progress has been made to improve the performance of optical gyroscopes for inertial navigation applications in terms of critical parameters such as bias stability, scale factor stability, and angular random walk (ARW). Specifically, resonant fiber optic gyroscopes (RFOGs) have emerged as a viable alternative to widely popular interferometric fiber optic gyroscopes (IFOGs). In a conventional RFOG, a single-wavelength laser source is used to generate counter-propagating waves in a ring resonator, for which the phase difference is measured in terms of the resonant frequency shift to obtain the rotation rate. However, the primary limitation of RFOG performance is the bias drift, which can be attributed to nonreciprocal effects such as Rayleigh backscattering, back-reflections, polarization instabilities, Kerr nonlinearity, and environmental fluctuations. In this paper, we review the challenges and opportunities of achieving performance enhancement in RFOGs. Full article

A low-cost, wavelength-tunable single-longitudinal-mode (SLM) thulium–holmium co-doped fiber laser (THDFL) in a 2 μm band with a simple structure is described in the present paper. To obtain a stable SLM and narrow laser linewidth, a five-coupler-based three-ring (FCTR) filter is utilized in the ring cavity of the fiber laser. Tunable SLM wavelength output from THDFLs with kHz linewidths can be achieved by designing the FCTR filter with an effective free-spectral range and a 3 dB bandwidth at the main resonant peak. The measurement results show that the laser is in the SLM lasing state, with a highly stabilized optical spectrum, a linewidth of approximately 9.45 kHz, an optical signal-to-noise ratio as high as 73.6 dB, and a relative intensity noise of less than −142.66 dB/Hz. Furthermore, the wavelength can be tuned in the range of 2.6 nm. The proposed fiber laser has a wide range of applications, including coherence optical communication, optical fiber sensing, and dense wavelength-division-multiplexing. Full article

A multimode fiber-based sensor is proposed and demonstrated for the detection of lead traces in contaminated water. The sensing mechanism involves using a light sheet to excite a specific group of skew rays that optimizes light absorption. The sensing region features an inline microbubble structure that funnels the skew rays into a tight ring, thereby intensifying the evanescent field. The sensitivity is further refined by incorporating gold nanoparticles, which amplify the evanescent field strength through localized surface plasmon resonance. The gold nanoparticles are functionalized with oxalic acid to improve specificity for lead ion detection. Experiment results demonstrated the significantly enhanced absorption sensitivity of the proposed sensing method for large center offsets, achieving a detection limit of 0.1305 ng/mL (the World Health Organization safety limit is 10 ng/mL) for concentrations ranging from 0.1 to 10 ng/mL. Full article