Search Results (93)

Although thick electrodes hold significant potential for enhancing battery energy density, their practical application is limited by restricted ion transport kinetics. Constructing porous structures within thick electrodes is a widely adopted strategy to address this limitation, but it often compromises mass retention and mechanical integrity. In this study, a microchannel structure that balances the electrochemical and mechanical properties of the electrode was identified through simulation and precisely fabricated using femtosecond laser technology. Furthermore, the ultra-short pulse duration and high pulse energy of femtosecond lasers introduce oxygen vacancies into the electrode material, thereby enhancing its electrical conductivity. The obtained electrode exhibited excellent electrochemical performance under high-rate charging and discharging conditions, achieving significantly enhanced cycling stability and capacity retention, with a capacity 1.99 times greater than that of the unstructured electrode after 100 cycles. Meanwhile, the mechanical stability of the laser-processed electrode was maintained. This study provides new insights into the structural design and processing of the thick electrode and contributes to advancements in the field of energy storage. Full article

Superhydrophobic surfaces have garnered significant attention due to their pivotal roles in various fields. Femtosecond laser technology provides a feasible means for inducing superhydrophobic microstructures on material surfaces. However, due to the unclear influence mechanisms of process parameters, as well as the high cost and time-consuming nature of experiments, identifying the optimal femtosecond laser processing parameters within the process space remains a significant challenge. To address this issue, a process optimization framework that couples machine learning and genetic algorithms was proposed and successfully applied to the optimization of femtosecond laser-induced groove structures on TC4 alloy surfaces. Firstly, based on 64 sets of experimental data, the effects of the power, scanning speed, and scanning interval on the micro-groove structures and their wetting properties were discussed in detail. Furthermore, by utilizing this small sample dataset, various machine learning algorithms were employed to establish a prediction model for the contact angle, among which support vector regression demonstrated the optimal predictive accuracy. Three additional dimensional variables, i.e., the number of effective pulses, energy deposition rate, and roughness, were also added to the original dataset vectors as extra dimensions to participate in and guide the model training process. The prediction model was further coupled into a genetic algorithm to achieve the quantitative design of femtosecond laser processing. Compared to the best hydrophobicity in the original dataset, the contact angle of the designed process was improved by 5.5%. The proposed method provides an ideal solution for accurately predicting wetting properties and identifying optimal processes, thereby accelerating the development and application of femtosecond laser-induced superhydrophobic microstructures. Full article

Advanced packaging represents a crucial technological evolution aimed at overcoming limitations posed by Moore’s Law, driving the semiconductor industry from two-dimensional toward three-dimensional integrated structures. The increasing complexity and miniaturization of electronic devices have significantly heightened the challenges associated with failure analysis during process development. The focused ion beam–scanning electron microscope (FIB-SEM), characterized by its high processing precision and exceptional imaging resolution, has emerged as a powerful solution for the fabrication, defect localization, and failure analysis of micro- and nano-scale devices. This paper systematically reviews the innovative applications of FIB-SEM in the research of core issues, such as through-silicon-via (TSV) defects, bond interfacial failures, and redistribution layer (RDL) electromigration. Additionally, the paper discusses multimodal integration strategies combining FIB-SEM with advanced analytical techniques, such as high-resolution three-dimensional X-ray microscopy (XRM), electron backscatter diffraction (EBSD), and spectroscopy. Finally, it provides a perspective on the emerging applications and potential of frontier technologies, such as femtosecond-laser-assisted FIB, in the field of advanced packaging analysis. Full article

Precision micromilling is currently widely used for the fabrication of injection mold inserts for the mass production of microfluidic devices. However, for complex devices with micrometer-scale and high density of structures, micromilling results in high production times and costs for production runs of hundreds or thousands of units. Femtosecond laser (fs-laser) technology has emerged as a promising solution for high-precision micromachining. This study analyzes the potential of fs-laser micromachining for the fabrication of injection mold inserts for the large-scale production of thermoplastic microfluidic devices. For the evaluation of technology, a reference design was defined. The parameters of the fs-laser process were optimized to achieve high resolution of the structures and optimal surface quality, aiming to minimize production times and costs while ensuring the quality of the final part. The microstructures were replicated in two different grades of COC (Cyclic Olefin Copolymer) by injection molding. The dimensional tolerance of the structures and the surface finish achieved both in the insert and the polymer parts were characterized by scanning electron microscopy (SEM) and confocal microscopy. The surface quality of the final parts and its suitability for microfluidic fabrication were also assessed performing chemical bonding tests. The fs-laser machining process has shown great potential for the mass production of microfluidic devices. The developed process has enabled for a reduction of up to 90% in the fabrication times of the insert compared to micromilling. The parts exhibited very smooth surfaces, with roughness values (Sa) of 64.6 nm for the metallic insert and 71.8 nm and 72.9 nm for the COC E-140 and 8007S-04 replicas, respectively. The dimensional tolerance and the surface quality need to be improved to be competitive with the finishes achieved with precision micromilling. Nonetheless, there is still room for improvement considering the significant reduction in the production times through new laser processing strategies. Full article

With the growing demand for high-performance computing (HPC), artificial intelligence (AI), and data communication and storage, new chip technologies have emerged, following Moore’s Law, over the past few decades. As we enter the post-Moore era, transistor dimensions are approaching their physical limits. Advanced packaging technologies, such as 3D chiplets hetero-integration and co-packaged optics (CPO), have become crucial for further improving system performance. Currently, most solutions rely on silicon-based technologies, which alleviate some challenges but still face issues such as warpage, bumps’ reliability, through-silicon vias’ (TSVs) and redistribution layers’ (RDLs) reliability, and thermal dissipation, etc. Glass, with its superior mechanical, thermal, electrical, and optical properties, is emerging as a promising material to address these challenges, particularly with the development of femtosecond laser technology. This paper discusses the evolution of both conventional and advanced packaging technologies and outlines future directions for design, fabrication, and packaging using glass substrates and femtosecond laser processing. Full article

Perovskite quantum dots (PQDs), with their excellent optical properties, have become a leading semiconductor material in the field of optoelectronics. However, to date, it has been a challenge to achieve the three-dimensional high-resolution patterning of perovskite quantum dots. In this paper, an in situ femtosecond laser-direct-writing technology was demonstrated for three-dimensional high-resolution patterned CsPbBr₃ PQDs using a two-photon photoresist nanocomposite doped with the CsPbBr₃ perovskite precursor. By adjusting the laser processing parameters, the minimum line width of the PQDs material was confirmed to be 98.6 nm, achieving a sub-100 nm PQDs nanowire for the first time. In addition, the fluorescence intensity of the laser-processed PQDs can be regulated by the laser power. Our findings provide a new technology for fabricating high-resolution display devices based on laser-direct-writing CsPbBr₃ PQDs materials. Full article

Inspired by the ventral scale structure of the oriental sand boa, this study successfully fabricated multiscale bioinspired alumina (Al₂O₃) ceramics by combining the excellent mechanical properties, high-temperature resistance, and high hardness of ceramic composites with direct ink writing (DIW) 3D printing technology and femtosecond laser processing. A MoS₂ thin film was then deposited on the ceramic surface via radio frequency magnetron sputtering (PVD) to systematically investigate the impact of bioinspired structures on the tribological properties of ceramic composites under both dry and lubricated conditions. Experimental results demonstrated that bioinspired structures at different scales exhibited significant friction-reducing and wear-resistant characteristics compared to blank structures. Specifically, under room-temperature conditions, the friction coefficients of bioinspired ceramic composites with solid lubricants and oil lubrication were 0.3 and 0.148, respectively, indicating excellent tribological performance. These findings confirm the synergistic lubrication effect between bioinspired structures, two-dimensional solid lubricants, and lubricating oil, which significantly enhanced the friction-reducing and wear-resistant properties of ceramic components. Therefore, the synergistic design of multiscale bioinspired structures and solid lubricants provides an innovative strategy for the advanced application of ceramic components. Full article

Currently, the quartz glass–TC4 dissimilar joint has been applied in fields such as radiation environment testing, reactor engineering, and other areas. However, the high brittleness of the quartz glass and thermal mismatch during the welding process limit require further development. Thus, a femtosecond laser was employed to perform the direct joining of these materials under non-optical contact conditions, with the aid of a well-designed clamp and optimized process, and the effect of pulse energy on the microstructure and mechanical properties was analyzed. It was revealed that a lot of welding zones form at the interface through the diffusion of Si, O, and Ti and, thus, consist of a stable joint. Element distribution is related to pulse energy, which can affect the composition of secondary phases in the weld zones. The maximum shear strength of joints was 10.4 MPa with laser pulses of 0.3 mJ, while a further increase in the pulse energy led to more defects and stress unevenness. These findings provide valuable insights into enhancing the reliability of metal–glass welding joints and the promotion of femtosecond laser technology. Full article

Gallium nitride (GaN) exhibits distinctive physical and chemical properties that render it indispensable in a multitude of electronic and optoelectronic devices. Given that GaN is a typical hard and brittle material that is difficult to machine, femtosecond laser technology provides an effective and convenient tool for processing such materials. However, GaN undergoes complex physical and chemical changes during high-power ablation, which poses a challenge to high-precision processing with controllable geometry. In this study, the quantitative relationship between the parameters of a single-pulse femtosecond laser and GaN ablation morphology was investigated using isotherm distribution. A multiphysics model using COMSOL Multiphysics^® was developed to generate the isothermal distributions. Experiments were conducted on the femtosecond laser ablation of GaN at various single-pulse energies, and the resulting ablation morphologies were compared with the predictions from the multiphysics model. The comparison demonstrated that the calculated isotherm distribution accurately predicted not only the ablation diameter and depth but also the crater shape across a broad range of laser fluences. The predicted errors of the ablation diameters and depths were within 4.71% and 10.9%, respectively. The root mean square error (RMSE) and coefficient of determination (R²) were employed to evaluate the prediction errors associated with the crater shapes, which fell within the range of 0.018–0.032 μm and 0.77–0.91, respectively. This study can provide an important reference for utilizing femtosecond lasers in the precise ablation of GaN to achieve desired geometries. Full article

Ultrafast laser welding technology for transparent materials has developed rapidly in recent years; however, high-strength non-optical contact transparent material welding has been a challenge. This work presents a welding method for silica glass using a double-pulse femtosecond (fs) laser and optimizes the laser processing parameters to enhance the welding performance. The welding characteristics of silica glass are analyzed under different time delays by controlling the pulse delay of double pulses. In addition to comprehensively study the influence of various experimental conditions on double-pulse fs laser welding, multi-level tests are designed for five factors, including average laser power, pulse delay, scanning interval, scanning speed, and repetition rate. Finally, by optimizing the parameters, a welding strength of 57.15 MPa is achieved at an average power of 3500 mW, repetition rate of 615 kHz, pulse delay of 66.7 ps, scanning interval of 10 µm, and scanning speed of 1000 µm/s. This work introduces a new approach to glass welding and presents optimal parameters for achieving higher welding strength, which can be widely used in aerospace, microelectronic packaging, microfluidics, and other fields. Full article

In this paper, multifunctional, multilevel phase plates of quartz substrate were efficiently prepared by using a newly developed polygon scanner-based femtosecond laser photolithography system combined with inductively coupled discharge plasma reactive-ion etching (ICP-RIE) technology. The femtosecond laser photolithography system can achieve a scanning speed of 5 m/s and a preparation efficiency of 15 cm²/h while ensuring an overlay alignment accuracy of less than 100 nm and a writing resolution of 500 nm. The ICP-RIE technology can control the etching depth error within ±5 nm and the mask-to-mask edge error is less than 1 μm. An 8-level Fresnel lens phase plate with a focal length of 20 mm and an 8-level Fresnel axicon phase plate with a cone angle of 5° were demonstrated. The diffraction efficiency was greater than 93%, and their performance was tested for focusing and glass cutting, respectively. Combined with the high-speed femtosecond laser photolithography system’s infinite field-of-view (IFOV) processing capability, the one-time direct writing preparation of phase plate masks of different sizes was realized on a 6-inch wafer. This is expected to reduce the production cost of quartz substrate diffractive optical elements and promote their customized mass production. Full article

Currently, the technology of imparting the necessary reflective properties to a surface is becoming increasingly important. Darkening the surface and matting it helps to diffuse the reflected beam and prevent glare. The surface’s reflective properties are determined by its microstructure. Modern pico- and femtosecond lasers make it possible to obtain surfaces with high precision and create various LIPSS (laser-induced periodic surface structure) types. In this article, we describe the process of formation of a complex two-periodic microstructure on the surface of AISI 321 stainless steel under the influence of radiation from femtosecond lasers and describe the process of scattering of a light beam by the resulting surface. Modeling shows that the presence of an additional transparent coating on a flat surface does not improve its scattering properties and does not eliminate glare. In the event that a complex two-periodic structure is formed on the reflective surface and the coating surface, the nature of the reflection has a clearly defined scattered character, regardless of the angle of incidence of the light beam. This study shows the feasibility and effectiveness of forming a two-periodic structure in order to give it stealth characteristics and reduce visibility. Full article

Ultrafast lasers, characterized by femtosecond and picosecond pulse durations, have revolutionized material processing due to their high energy density and minimal thermal diffusion, and have played a transformative role in precision manufacturing. This review first traces the progression from early ruby lasers to modern titanium–sapphire lasers, highlighting breakthroughs like Kerr-lens mode-locking and chirped pulse amplification. It also examines the interaction mechanisms between ultrafast pulses and various materials, including metals, dielectrics, and semiconductors. Applications of ultrafast lasers in microstructure processing techniques are detailed, such as drilling, cutting, surface ablation, and nano welding, demonstrating the versatility and precision of the technology. Additionally, it covers femtosecond laser direct writing for optical waveguides and the significant advancements in imaging and precision measurement. This review concludes by discussing potential future advancements and industrial applications of ultrafast lasers. Full article

Waveguide lasers have the advantages of miniature and compact structure and have broad application prospects in photonic integration and on–chip laboratories. The development of femtosecond laser direct–writing technology makes the processing of transparent materials more flexible and controllable. This paper mainly introduces a waveguide laser based on femtosecond laser direct–writing technology. Firstly, the applications of femtosecond laser direct–writing technology in an optical waveguide are introduced, including the principles of femtosecond laser direct–writing technology, common optical wave scanning methods, and types of optical waveguides. After that, we summarize the development of a waveguide continuous–wave laser, a Q–switched laser and a mode–locked laser from visible to mid–infrared wavebands and analyze some new representative work. Finally, we explain the difficulty of compensating for dispersion in pulse waveguide lasers and summarize some new ideas that have been proposed to solve the problem. Full article

Bismuth germanate (Bi₄Ge₃O₁₂, BGO) is a widely used optical sensing material with a high electro-optic coefficient, ideal for optical electric field sensors. Achieving high precision in electric field sensing requires fabricating optical waveguides on BGO. Traditional waveguide writing methods face challenges with this material. This study explores using femtosecond laser writing technology for preparing waveguides on BGO, leveraging ultrafast optical fields for superior material modification. Our experimental analysis shows that a cladding-type waveguide, written with a femtosecond laser at 200 kHz repetition frequency and 10.15 mW average power (pulse energy of 50.8 nJ), exhibits excellent light-guiding characteristics. Simulations of near-field optical intensity distribution and refractive index variations using the refractive index reconstruction method demonstrate that the refractive index modulation ensures single-mode transmission and effectively confines light to the core layer. In situ refractive index characterization confirms the feasibility of fabricating a waveguide with a refractive index reduction on BGO. The resulting waveguide has a loss per unit length of approximately 1.2 dB/cm, marking a successful fabrication. Additionally, we design an antenna electrode, analyze sensor performance indicators, and integrate a preparation process plan for the antenna electrode. This achievement establishes a solid experimental foundation for future studies on BGO crystal waveguides in electric field measurement applications. Full article