Search Results (143)

We report the experimental observation of dissipative solitons (DS) in an erbium-doped fiber laser mode-locked with ethylene glycol. Stable individual dissipative solitons with the fundamental repetition frequency of 35.17 MHz are obtained. The spectral profiles exhibit dynamic variation, adopting either a parabolic-like or an M-like shape at varying pump levels. Moreover, through increasing the pump power and/or appropriately regulating the polarization controller, multiple dissipative solitons, including soliton pairs and soliton triplet states have also been achieved. The generation mechanism is attributed to the phenomenon of peak clamping effect. This is the first demonstration of a dissipative soliton laser utilizing ethylene glycol as a saturable absorber. It is anticipated that this demonstration will spur further attention on organic liquid SAs and potentially extend significant influence for the application of ultrafast lasers. Full article

We propose a novel mathematical model of a multistable erbium-doped fiber laser based on Caputo fractional derivative equations. The model is used to investigate how the laser dynamics evolve as the derivative order is varied. Our results demonstrate that the fractional-order formulation provides a more accurate description of the experimentally observed laser dynamics compared to conventional integer-order models. This study highlights the importance of fractional calculus in modeling complex nonlinear photonic systems and offers new insights into the dynamics of multistable lasers. Full article

We report the simultaneous generation of conventional solitons (CSs) and dissipative solitons (DSs) in an erbium-doped mode-locked fiber laser with a dual-branch cavity configuration based on the nonlinear polarization rotation (NPR) technique. By incorporating fibers with different dispersion properties in two propagation branches, the laser can establish simultaneous operation in the normal and anomalous dispersion regimes within the respective loops, enabling the generation of two distinct soliton types. The CSs exhibit a 3 dB spectral bandwidth of 9.7750 nm and a pulse duration of 273 fs, while the DSs have a quasi-rectangular spectrum spanning 18.7074 nm and a pulse duration of 2.2 ps, which can be externally compressed to 384 fs. The fundamental repetition rate is approximately 21 MHz, with a repetition rate difference of 216 Hz for the two pulse trains. Stable second-order, third-order, and fourth-order harmonic mode-locking (HML) can be achieved through optimization of pump power and intracavity polarization states. The laser we build in this work has significant potential for applications in high-precision spectroscopy and asynchronous optical sampling. Full article

We present an all-fiber erbium-doped mode-locked laser capable of switching among continuously tunable single-pulse mode-locking, wavelength-multiplexing asynchronous-pulse mode-locking, and polarization-multiplexing asynchronous-pulse mode-locking states. The multiplexing mechanisms under different conditions are confirmed by separating the asynchronous-pulse sequences. Experimental results and numerical simulations indicate that the adjustment of the polarization controller within the Sagnac loop is the key factor for switching between wavelength- and polarization-multiplexing asynchronous-pulse mode-locking. The multiple output characteristics of the same laser can support diverse application scenarios, offering significant cost reduction in practical applications. To the best of our knowledge, this is the first demonstration of switching between wavelength- and polarization-multiplexing asynchronous-pulse mode-locking states in a noise-like laser. Compared to previous related work, the proposed laser not only enables tunable mode-locking wavelengths but also achieves higher pulse energy. This work provides a light source solution with a simple structure and high switchability for dual-comb applications. Full article

This paper presents the implementation of a real-time nonlinear state observer applied to an erbium-doped fiber laser system. The observer is designed to estimate population inversion, a state variable that cannot be measured directly due to the physical limitations of measurement devices. Taking advantage of the fact that the laser intensity can be measured in real time, an observer was developed to reconstruct the dynamics of population inversion from this measurable variable. To validate and strengthen the estimate obtained by the observer, a Recurrent Wavelet First-Order Neural Network (RWFONN) was implemented and trained to identify both state variables: the laser intensity and the population inversion. This network efficiently captures the system’s nonlinear dynamic properties and complements the observer’s performance. Two metrics were applied to evaluate the accuracy and reliability of the results: the Euclidean distance and the mean square error (MSE), both of which confirm the consistency between the estimated and expected values. The ultimate goal of this research is to develop a neural control architecture that combines the estimation capabilities of state observers with the generalization and modeling power of artificial neural networks. This hybrid approach opens up the possibility of developing more robust and adaptive control systems for highly dynamic, complex laser systems. Full article

Ultrafast lasers operating at 740 nm and 820 nm have attracted widespread attention as two-photon light sources for the detection of biological metabolism. Here, we report on a solid-like quartz-encapsulated femtosecond laser with a repetition rate of 80 MHz, delivering 740 nm and 820 nm femtosecond laser pulses. This home-built laser system was realized by employing an erbium-doped 1560 nm fiber laser as the fundamental laser source. A quartz-encapsulated nonlinear frequency conversion stage, consisting of a second-harmonic generation (SHG) stage and self-phase modulation (SPM)-based nonlinear spectral broadening stage, was utilized to deliver 30 mW, 53.7 fs, 740 nm laser pulses and the 15 mW, 60.8 fs, 820 nm laser pulses. Further imaging capabilities of both wavelengths were validated using a custom-built inverted two-photon microscope. Clear imaging results were obtained from mouse kidney sections and pollen samples by collecting the corresponding fluorescence signals. The achieved results demonstrate the great potential of this laser source for advanced two-photon microscopy in metabolic detection. Full article

To enable the highly sensitive detection of acetylene (C₂H₂) dissolved in transformer oil, a high-power quartz-enhanced photoacoustic spectroscopy (QEPAS) sensing system is proposed. A standard 32.7 kHz quartz tuning fork (QTF) was employed as an acoustic transducer, coupled with an optimized acoustic resonator to enhance the acoustic signal. The laser power was boosted to 150 mW using a C-band erbium-doped fiber amplifier (EDFA), achieving a detection limit of 469 ppb for C₂H₂ with an integration time of 1 s. The headspace degassing method was utilized to extract dissolved gases from the transformer oil, and the equilibrium process for the release of dissolved C₂H₂ was successfully monitored using the developed high-power QEPAS system. This approach provides reliable technical support for the real-time monitoring of the operational safety of power transformers. Full article

The use of analog radio-over-fiber (RoF) systems combined with power-over-fiber (PoF) systems has been proposed in recent years for applications involving remote sensors used in hazardous environments or where electrical wiring may be impractical. This article presents a hybrid architecture topology that combines PoF and RoF, using Raman amplification to obtain RF gain. The first emphasis is placed on the use of two types of high-power laser sources (HPLSs) for the PoF system: a 1480 nm Raman-based HPLS and a 1550 nm HPLS that is based on an erbium-doped fiber amplifier (EDFA). The second emphasis of this paper is on how these two HPLSs simulate Raman scattering (SRS) in the fiber, considering different lengths of SMF 28 for the link. Thus, a comparative analysis is proposed considering the effects induced on the RF signal, mainly focused on its RF power gain ($G_{RF}$), noise figure (NF), and spurious-free dynamic range (SFDR). The obtained results show that the architecture using a PoF system based on the 1550 nm HPLS benefits from a lower noise figure degradation, even when the noise generated by the optical amplification is considered. Full article

In this work, we report the formation of multiple mode-locking states in an Erbium/Ytterbium co-doped fiber laser, such as domain-wall (DW) dark pulses, high-order dark harmonic pulses, dissipative soliton resonance (DSR) pulses, and dual-wavelength h-shaped pulses. By increasing the pump power and adjusting the quarter-wave retarder (QWR) plates, we experimentally achieve 310th-order harmonic dark pulses. DSR pulses emerge at a pump power of 1.01 W and remain stable up to 9.07 W, reaching a maximum pulse width of 676 ns and a pulse energy of 1.608 µJ, while Dual-wavelength h-shaped pulses have a threshold of 1.42 W and maintain stability up to 9.07 W. Using a monochromator, we confirm that these h-shaped pulses result from the superposition of a soliton-like pulse and a DSR-like pulse, emitting at different wavelengths but locked in time. The fundamental repetition rate for dark pulsing, DSR, and h-shaped pulses is 321.34 kHz. This study provides new insights into complex pulse dynamics in fiber lasers and demonstrates the versatile emission regimes achievable through precise pump and polarization control. Full article

This study presents the synthesis of manganese molybdenum tetraoxide (MnMoO₄)-based nanoparticles and then their experimental demonstration as saturable absorbers (SAs) in erbium-doped fiber lasers (EDFLs). The MnMoO₄ nanoparticles were prepared and then embedded between the fiber ferrule to act as an SA to generate Q-switched pulsed operation in EDFLs. For the characterization, scanning electron microscopy (SEM) was employed to confirm the particle size of the prepared MnMoO₄ nanoparticles, and the SA optical properties were further investigated by measuring their modulation depth and saturation intensity. By implementing the prepared SA within the cavity, the measured results revealed that under pump power ranging from 28 to 312.5 mW, the laser exhibited Q-switched pulse durations varying from 15.22 to 2.35 µs and repetition rates spanning from 24.98 to 88.11 kHz. The proposed EDFL system delivered an average output power between 0.128 and 2.95 mW, pulse energies ranging from 5.12 to 33.49 nJ, and peak power from 0.281 to 6.26 mW. The laser stability was also confirmed by continuously noticing the pulse duration, emission wavelengths, and pulse repetition rates for 4 h. Finally, a numerical model based on a nonlinear Schrödinger equation (NLSE) was employed to validate both experimental and theoretical results of the passive Q-switched EDFL. These findings highlight the potential of EDFLs utilizing MnMoO₄-based SAs for potential applications in pulsed laser sources. Full article

Random lasers (RLs) based on glasses and glass-ceramics doped with rare-earth ions (REI) deserve great attention because of their specific physical properties such as large thermal stability, possibility to operate at high intensities, optical wavelength tunability, and prospects to operate Fiber-RLs, among other characteristics of interest for photonic applications. In this article, we present a brief review of experiments with RLs based on tellurite and germanate glasses and glass-ceramics doped with neodymium (Nd³⁺), erbium (Er³⁺), and ytterbium (Yb³⁺) ions. The glass samples were fabricated using the melt-quenching technique followed by controlled crystallization to achieve the glass-ceramics. Afterwards, the samples were crushed to obtain the powder samples for the RLs experiments. The experiments demonstrated RLs emissions at various wavelengths, with feedback mechanisms due to light scattering at grain/air and crystalline/glass interfaces. The phenomenon of replica symmetry breaking was verified through statistical analysis of the RLs intensity fluctuations, indicating a photonic phase-transition (corresponding to the RL threshold) analogous to the paramagnetic-to-spin glass transition in magnetic materials. The various results reported here highlight the potential of glasses and glass-ceramics for the development of RLs with improved performance in terms of reduction of laser threshold and large lifetime of the active media in comparison with organic materials. Full article

We propose and demonstrate a tunable femtosecond electro-optic optical frequency comb by shaping a continuous-wave seed laser in an all-fiber configuration. The seed laser, operating at 1.5 μm, is first cascade-phase-modulated and subsequently de-chirped to generate low-contrast pulses of approximately 8 ps at a repetition rate of 5.95 GHz. These pulses are then refined into clean, high-quality picosecond pulses using a Mamyshev regenerator. The generated source is further amplified using an erbium–ytterbium-doped fiber amplifier operating in a highly nonlinear regime, yielding output pulses compressed to around 470 fs. Tunable continuously across a 5.7~6 GHz range with a 1 MHz resolution, the picosecond pulses undergo nonlinear propagation in the final amplification stage, leading to output pulses that can be further compressed to a few hundred femtoseconds. By using a tunable bandpass filter, the center wavelength and spectral bandwidth can be flexibly tuned. This system eliminates the need for mode-locked cavities, simplifying conventional ultrafast electro-optic combs by relying solely on phase modulation, while delivering femtosecond pulses at multiple-gigahertz repetition rates. Full article

Femtosecond fiber lasers are widely utilized across various fields and also serve as an ideal platform for studying soliton dynamics. Bound-state solitons, as a significant soliton dynamic phenomenon, attract widespread attention and research interest because of their potential applications in high-speed optical communication, all-optical information storage, quantum computing, optical switching, and high-resolution spectroscopy. We investigate the effects of pump power variations on the formation of mode-locked solitons and bound-state solitons in a femtosecond fiber laser with a Cr₂S₃ saturable absorber (SA) through numerical simulations while observing the transition, formation, and break-up process of bound soliton pulses. By optimizing the cavity structure and adjusting the net dispersion, the mode-locked soliton is obtained based on this SA. This is the narrowest solitons produced by this SA to date, exhibiting the smallest time-bandwidth product. Moreover, stable double-bound solitons and unique (2 + 1) triple-bound solitons are successfully obtained. The diverse bound-state solitons not only demonstrate the excellent nonlinear absorption properties of Cr₂S₃ as a saturable absorber but also expand the scope of applications for Cr₂S₃ saturable absorbers in fiber lasers. Full article

This study presents the liquid crystal Fabry–Pérot etalon (LC-FP) as the preferred laser wavelength tuning solution within a erbium-doped fiber ring laser architecture. The laser cavity wavelength can be adjusted by applying varying voltages to the LC-FP. Furthermore, tuning the laser wavelength can be facilitated by modifying the incident light through changes in the steering angle of the LC-FP, which is attributed to the angular dispersion characteristics of the device. The operational range for the steering angle of the LC-FP is ± 4 to 18 degrees. This architectural framework is adept at facilitating the generation of single-wavelength and dual-wavelength lasers within the C band. The tunable range for a single wavelength is approximately 13 nm, while the tunable range for dual wavelengths is around 14 nm, with a wavelength spacing of approximately 17.5 nm. These capabilities are primarily influenced by the operational wavelength of the erbium-doped fiber amplifier (EDFA), the operating wavelength of the collimator that directs the fiber optic beam into the LC-FP, and the fixed thickness of the LC-FP. Full article

Graphene oxide (GO) and reduced graphene oxide (rGO) have emerged as robust materials in the development of SAs for erbium-doped fiber lasers (EDFLs). Their exceptional optical properties, such as broadband absorption and fast recovery times, make them ideal candidates for achieving ultrashort pulse operation in EDFLs. With its higher oxygen content, GO offers greater nonlinearity and a tunable absorption spectrum, while rGO, yielded through chemical reduction, exhibits enhanced electrical conductivity and higher saturable absorption. These properties facilitate the generation of ultrashort pulses in EDFLs, which are highly desired for various medical imaging, telecommunications, and material processing applications. This review paper comprehensively analyzes the advancements in GO and rGO SAs in the context of EDFLs for mode-locking and Q-switching applications. The performance of EDFLs utilizing GO and rGO SAs is critically evaluated, focusing on key parameters, such as modulation depth, pulse duration, repetition rate, average power, pulse energy, peak power, and signal-to-noise ratio. Additionally, this review delves into the various synthesis methods of GO and rGO thin film, highlighting their impact on the optical properties and performance of SAs. The discussion on techniques to integrate the SAs into laser cavities includes direct deposition of nanoparticles/thin-film-based SAs, tapered-fiber-based SAs, and D-shaped SAs. Furthermore, the paper explores the challenges encountered during the fabrication of ideal GO and rGO SAs, with issues related to uniformity, stability, and tunability, along with proposed solutions to address these challenges. The insights provided offer valuable guidance for future research aimed at enhancing the performance of EDFLs using GO/rGO SAs. Full article