Search Results (5,899)

To address the inherent defects in the fabrication of AlCrN titanium alloy coatings and enhance interfacial bonding strength as well as tribological performance, an AlCrN coating was employed as an absorption layer and subjected to laser shock processing to form an AlCrN/TC4 transition layer. Subsequently, a secondary AlCrN coating was deposited to construct a gradient coating architecture. The surface and cross-sectional morphologies and elemental distributions under varying laser energies were systematically investigated, and the influence of laser energy on the adhesion and wear resistance of the gradient coatings was analyzed. The results demonstrate that with increasing laser impact energy, the thickness of the AlCrN/TC4 transition layer gradually decreases from 3.75 μm to 1.32 μm, accompanied by significant changes in elemental distribution across the surface and cross-section. The interfacial bonding strength of the gradient coating increases substantially from 13.6 N to 43.3 N, while the average friction coefficient rises from 0.436 to 0.507. Concurrently, the wear track depth is reduced, and the wear rate decreases from 86.46 × 10⁻⁵ mm³/(N·m) to 7.67 × 10⁻⁵ mm³/(N·m). Laser shock peening promotes elemental diffusion, enabling the formation of a diffusion-aided interlayer. The incorporation of this diffused zone facilitates the successful construction of a high-quality TC4 titanium alloy gradient coating, effectively broadening the film–substrate interface, enhancing surface hardness, and significantly improving both interfacial adhesion and wear resistance. Full article

In this paper, the bond performance of tensile lap-spliced Glass and Basalt Fiber-Reinforced Polymer bars is investigated in high-strength concrete. Eighteen large-scale GFRP-reinforced concrete beams were fabricated and subjected to four-point loading. Key parameters explored included bar diameter and splice length for both GFRP and BFRP reinforcement. The results indicate that the flexural capacity of GFRP-reinforced beams was comparable to that of BFRP-reinforced beams, though BFRP bars exhibited marginally superior bond and strength with concrete. The bond strength of spliced FRP bars was directly proportional to the splice length. This study also determined that characteristics of development lengths necessitate splice lengths that exceed the bar diameter 40 times to mitigate bond stress. Critical splice lengths, derived from experimental findings, were compared with existing models and code-based equations, specifically, Guide for the Design and Construction of Structural Concrete Reinforced with Fiber-Reinforced Polymer Bars (ACI 440.1R-15) and Canadian standard that provides comprehensive guidelines for incorporating Fiber-Reinforced Polymer reinforcement in concrete structures (CSA S806-12). Both codes were conservative in splice length prediction for GFRP and BFRP bars, with ACI 440.1R-15 showing greater accuracy for BFRP bars with a larger diameter. A modification factor, based on hyperbolic functions, is proposed to enhance the accuracy of ACI 440.1R-15 in predicting splice lengths for various FRP bar diameters. Full article

This study explores the effect of cation adsorption on the shear strength and mineralogical characteristics of smectite-rich landslide clay collected from the Nishinotani landslide in Ehime Prefecture, Japan. Laboratory experiments were conducted using aqueous solutions of calcium, magnesium, and potassium chlorides at concentrations of 1000, 6000, and 12,000 mg/L. Ion chromatography, X-ray diffraction (XRD), and ring shear tests were conducted to evaluate the interaction between ion uptake and its influence on the change in shear strength. The results showed that calcium and potassium ion adsorption increased with both concentration and time, leading to enhanced residual shear strength and crystallinity, primarily due to stronger Coulombic interactions and favorable ionic size compatibility with smectite. Conversely, magnesium ions exhibited adverse effects, including reduced strength and mineral ordering, attributed to calcium leaching and weaker interparticle bonding. The findings indicate that selective cation exchange can be an effective, sustainable alternative to conventional landslide stabilization methods, especially in fine-grained, expansive clay systems. This work contributes to the development of geochemically engineered landslide mitigation strategies based on microstructural and mineralogical reinforcement. Full article

Aircraft structures are highly susceptible to fatigue damage, particularly in thin-walled aluminum alloy components such as skin panels. Damage in the form of holes or material loss drastically reduces fatigue life and compromises structural safety, which makes effective repair strategies essential. This study presents an experimental investigation into the fatigue performance of EN AW-2024-T3 aluminum alloy plates with central openings subjected to uniform shear. Repair nodes were applied using two approaches: conventional riveted metal patches and adhesively bonded composite patches. Variants of patch geometry, thickness, and diameter were evaluated to determine their influence on load transfer, buckling response, and fatigue life. The results show that central holes significantly shorten fatigue life, with a 20 mm hole causing a 67% reduction and a 50 mm hole causing a 95% reduction when compared with undamaged plates. Riveted metal patches restored only part of the lost performance, as stress concentrators introduced by fastener holes initiated new fatigue cracks. In contrast, adhesively bonded composite patches provided a substantial improvement, extending fatigue life beyond that of the riveted solutions, improving buckling shape, and delaying crack initiation. Larger patches, particularly those combined with metallic inserts, proved most effective in restoring structural functionality. The findings confirm the effectiveness of bonded composite repairs as a lightweight and reliable method for extending fatigue life and enhancing the safety of damaged aircraft structures. The study highlights the importance of patch geometry and stiffness in the design of repair nodes. Full article

Bio-inspired flow-sensing and actuation mechanisms offer a promising path for enhancing the stability of flapping-wing flying robots (FWFRs) operating in dynamic and noisy environments. This study introduces a bio-inspired sensing and actuation feather unit (SAFU) that mimics the covert feathers of falcons and serves simultaneously as a distributed flow sensor and an adaptive actuation element. Each electromechanical feather (EF) passively detects airflow disturbances through deflection and actively modulates its flaps through an embedded actuator, enabling real-time aerodynamic adaptation. A reduced-order bond-graph model capturing the coupled aero-electromechanical dynamics of the FWFR wing and SAFU is developed to provide a physics-based training environment for a proximal policy optimization (PPO) based reinforcement learning controller. Through closed-loop interaction with this environment, the PPO policy autonomously learns control actions that regulate feather displacement, reduce airflow-induced loads, and improve dynamic stability without predefined control laws. Simulation results show that the PPO-driven SAFU achieves fast, well-damped responses with rise times below 0.5 s, settling times under 1.4 s, near-zero steady-state error across varying gust conditions and up to 50% alleviation of airflow-induced disturbance effects. Overall, this work highlights the potential of bio-inspired sensing-actuation architectures, combined with reinforcement learning, to serve as a promising solution for future flapping-wing drone designs, enabling enhanced resilience, autonomous flow adaptation, and intelligent aerodynamic control during operations in gusts. Full article

Type 2 diabetes mellitus (T2DM) is a globally prevalent chronic metabolic disorder that poses severe public health risks. Synthetic hypoglycemic agents are susceptible to inducing adverse reactions, thus driving the development of natural, safe and highly effective plant-derived hypoglycemic active compounds as a research hotspot. Inhibiting the activity of α-glucosidase and α-amylase represents an effective strategy to regulate postprandial blood glucose levels. This study investigated the synergistic hypoglycemic activity of a composite (PS-PP) formed by polysaccharide (PS) and polyphenols (PP) from Ziziphus jujuba Mill. cv. Muzao and elucidated the structural basis underlying this synergistic effect. First, MPS and MPP were isolated and purified, followed by the in vitro assembly to prepare PS-PP. The hypoglycemic activities of MPS, MPP and MPS-PP were evaluated via in vitro enzyme inhibition assays, while structural characterization was conducted using GPC-MALLS, FT-IR and SEM techniques. Results demonstrated that PS-PP exerted the strongest activity under optimal conditions (0.75 mg/mL concentration, pH 4.0, 1:2 mass ratio), with IC₅₀ values of 1.14 μg/mL and 0.82 μg/mL against the two enzymes, which were superior to those of polysaccharides (15.10 and 36.06 μg/mL) and polyphenols (1.18 and 46.24 μg/mL). Structural analysis revealed that the interaction between PS and PP was primarily mediated by hydrogen bonds. PS-PP exhibited significant differences from single-component compounds in molecular weight distribution, functional group binding and surface morphology. These structural alterations were identified as the key factors contributing to its enhanced hypoglycemic efficacy. This study clarifies the synergistic hypoglycemic mechanism of MPP-PS and lays a scientific foundation for the development of natural hypoglycemic preparations and functional foods. Full article

Polymer-based composites have emerged as viable alternatives to metals for applications requiring reduced weight, corrosion resistance, and cost-effectiveness; however, their relatively low mechanical strength remains a significant limitation. This study evaluates the flexural performance of unsaturated polyester composites reinforced with coconut shell charcoal (CC) powder at filler contents of 0%, 10%, 20%, and 30% by weight, in accordance with ASTM D790. The incorporation of 20 wt% CC yielded the highest flexural strength of 132.43 MPa, representing a 153% improvement compared to pure polyester (52.10 MPa). Flexural modulus also increased substantially at this composition, indicating enhanced stiffness resulting from improved interfacial bonding and efficient stress transfer. In contrast, increasing the filler content beyond 20 wt% resulted in a reduction of up to 32% in strength, attributed to particle agglomeration and void formation. Overall, the results identify 20 wt% CC as the optimal reinforcement level, significantly improving energy absorption and bending resistance, thereby positioning this composite as a promising candidate for lightweight structural applications. Full article

To address the clinical urgency of simultaneously monitoring multiple biomarkers in chronic wound infections, this study presents the innovative development of an electrochemical sensor based on a MWCNTs/MXene/PVA composite hydrogel. A dual-channel conductive network is constructed via the electrostatic self-assembly of the two-dimensional material MXene and multi-walled carbon nanotubes (MWCNTs). This strategy not only enhances the charge transfer efficiency but also effectively suppresses the aggregation of MWCNTs and exposes the electrocatalytic active sites. Additionally, the thermal annealing process is incorporated to facilitate the ordered arrangement of polyvinyl alcohol (PVA) nanocrystalline domains, strengthening the hydrogen bond-mediated interfacial adhesion and resolving the issues of hydrogel swelling and delamination. The detection limit (LOD) of the optimized sensor (MWCNTs_0.6/MXene_0.4/PVA) for pyocyanin (PCN) within complex biological matrices, including phosphate-buffered saline (PBS), Luria–Bertani (LB) broth, and saliva, was decreased to a range of 0.84~0.98 μM. Leveraging the disparities in the characteristic oxidation potentials (ΔE > 0.3 V) of PCN, uric acid (UA), and histamine (HA) in simulated wound exudate (SWE), the multi-component synchronous detection functionality of the non-specific sensor was expanded for the first time. This study offers a high-precision and multi-parameter integrated approach for point-of-care testing (POCT) of wound infections. Full article

Unsteady atmospheric disturbances significantly compromise the stability of ornithopters, necessitating advanced turbulence-mitigation strategies. In contrast, natural flyers display remarkable aerodynamic adaptability through dynamic flow-control mechanisms such as covert feathers, enabling stability across unsteady flow regimes. Drawing inspiration from this biological phenomenon, this study presents the modeling and hybrid control of a kestrel-based ornithopter equipped with a Nature-Inspired Flow Control Device (NFCD) that replicates the adaptive feather deployment mechanism observed in kestrels. A reduced-order multibody bond-graph model (BGM) of the full ornithopter is developed, incorporating the main body, propulsion system, rigid wings, and the NFCD subsystem. The model captures key fluid-structure-interaction (FSI) effects between morphing feathers and surrounding airflow. A Linear Quadratic Regulator (LQR) ensures optimal performance under nominal gust conditions (≤3 m/s), while an H₂ controller activates during high-intensity gusts (≥4 m/s) to enhance disturbance rejection through electromechanical feather actuation. A gain-scheduled transition is employed in the intermediate gust range (3–4 m/s) to ensure a smooth transition between controllers. Simulations indicate up to 70% reduction in gust-induced oscillations and 32% gust-mitigation efficiency, achieved through feather actuation in the NFCD combined with hybrid control, stabilizing the ornithopter in less than 1.4 s under higher gust conditions. The close correspondence between simulated responses and previously reported findings validates the proposed approach. Overall, by merging biomimetic aerodynamics, nature-inspired flow control, and advanced control design, the LQR-H₂ governed NFCD provides a promising pathway toward gust-tolerant ornithopters capable of resilient and stable flight in unsteady atmospheric environments. Full article

Sabkhas, hypersaline ecosystems along Kuwait’s coastal zone, are extreme environments that harbor diverse halophilic microorganisms with significant biotechnological potential. Despite this, they remain underexplored, particularly in the context of enzymes that can function under high salinity. The aim of this study is to identify bacterial isolates from Kuwait’s sabkhas that produce α-amylase under extreme environmental conditions and to purify and characterize the resulting halotolerant α-amylase. Among the seven α-amylase-producing isolates, Priestia sp. W243, isolated from Mina Abdullah, exhibited the highest enzyme production under optimal growth conditions of pH 9.0, 37 °C, and 7.5% NaCl. A novel halotolerant α-amylase with a remarkably high specific activity (8112.1 U/mg) was purified from this isolate using ultrafiltration, ion-exchange chromatography, and gel-filtration. The purified enzyme, with a molecular weight of 25 kDa, showed optimal activity at 40 °C, pH 8, and 3% NaCl. Notably, the enzyme remained active in the absence of salt and up to 15% NaCl, demonstrating exceptional halotolerance. Metal ion profiling revealed that enzyme activity was significantly enhanced by Co²⁺, whereas Ca²⁺ had a comparatively moderate effect on enzyme activity. When the effects of metal chelators were examined, EDTA, a strong metal chelator, inhibited the enzyme. However, the enzyme remained active when Ca²⁺ was specifically removed using EGTA, suggesting that this α-amylase may be a cobalt-dependent metalloenzyme, which is an unusual characteristic among known α-amylases. Additionally, the enzyme retained its catalytic activity under reducing conditions (e.g., in the presence of DTT and β-mercaptoethanol), indicating structural stability is independent of disulfide bonds. These unique properties distinguish this α-amylase from typical salt- or calcium-dependent counterparts and highlight its potential for industrial applications in high-salt food processing, baking, brewing, and environmental remediation. Full article

Hydrophobic bioactive compounds such as lutein exhibit poor water solubility and are prone to degradation. Liposomal delivery systems can enhance the solubility and physicochemical stability of lutein (LUT). Liposomes are primarily composed of phospholipids and cholesterol. Since phytosterol ester can reduce cholesterol levels and improve the performance of liposomes, this study used phytosterol oleate ester (POE) as a cholesterol substitute in the preparation of liposomes for delivering LUT (LUT-P-Lip). The physicochemical properties, microstructure, storage stability, antioxidant characteristics, and intermolecular interactions of the liposomes at different LUT concentrations were investigated. The results demonstrated that LUT-P-Lip had a size range of 50–100 nm, with intact morphology and uniform distribution. In vitro studies showed that LUT-P-Lip significantly enhanced the storage stability and antioxidant activity of LUT. The analysis of intermolecular interactions revealed that the enhanced stability was mediated by an increased number of hydrogen bonds and modulation of membrane fluidity. In conclusion, replacing cholesterol with POE during liposome formation enhances both the stability and antioxidant activity of the resulting liposomes. Full article

Lignin, an abundant and renewable biopolymer, holds significant potential for asphalt modification owing to its unique aromatic structure and reactive functional groups. This review summarizes the main lignin preparation routes and key physicochemical attributes and assesses its applicability for enhancing asphalt performance. The physical incorporation of lignin strengthens the asphalt matrix, improving its viscoelastic properties and resistance to oxidative degradation. These enhancements are mainly attributed to the cross-linking effect of lignin’s polymer chains and the antioxidant capacity of its phenolic hydroxyl groups, which act as free-radical scavengers. At the mixture level, lignin-modified asphalt (LMA) exhibits improved aggregate bonding, leading to enhanced dynamic stability, fatigue resistance, and moisture resilience. Nevertheless, excessive lignin content can have a negative impact on low-temperature ductility and fatigue resistance at intermediate temperatures. This necessitates careful dosage optimization or composite modification with softeners or flexible fibers. Mechanistically, lignin disperses within the asphalt, where its polar groups adsorb onto lighter components to boost high-temperature performance, while its strong interaction with asphaltenes alleviates water-induced damage. Furthermore, life cycle assessment (LCA) studies indicate that lignin integration can substantially reduce or even offset greenhouse gas emissions through bio-based carbon storage. However, the magnitude of the benefit is highly sensitive to lignin production routes, allocation rules, and recycling scenarios. Although the laboratory research results are encouraging, there is a lack of large-scale road tests on LMA. There is also a lack of systematic research on the specific mechanism of how it interacts with asphalt components and changes the asphalt structure at the molecular level. In the future, long-term service-road engineering tests can be designed and implemented to verify the comprehensive performance of LMA under different climates and traffic grades. By using molecular dynamics simulation technology, a complex molecular model containing the four major components of asphalt and lignin can be constructed to study their interaction mechanism at the microscopic level. Full article

Recent advances in nanotechnology have highlighted the transformative potential of carbon-based nanomaterials, such as carbon nanofibers, carbon nanotubes, and graphene, in cementitious systems. These materials have shown a remarkable ability to enhance the mechanical strength, fracture toughness, and overall functional performance of cementitious composites. Their nanoscale dimensions and exceptional intrinsic properties allow for effective stress bridging, crack arrest, and matrix densification. Despite these promising features, the current understanding remains limited, particularly regarding their application to concrete. Furthermore, literature lacks systematic, parallel evaluations of their respective effectiveness in improving both mechanical performance and long-term durability, as well as their potential to impart true multifunctionality to concrete structures. It is worth noting that significant and statistically significant improvements in fracture behavior were observed at specific nanofiller concentrations, suggesting strong potential for the material system in next-generation innovative infrastructure applications. Experimental results demonstrated that both CNTs and GNPs significantly enhanced the mechanical performance of concrete, with flexural strength increases of approximately 49% and 38%, and compressive strength improvements of 22% and 47%, respectively, at optimum contents of 0.6 wt.% CNTs and 0.8 wt.% GNPs. SEM analyses confirmed improved matrix densification and interfacial bonding at these concentrations, while higher dosages led to agglomeration and reduced performance. This gap highlights the need for targeted experimental studies to elucidate the structure-property relationships governing these advanced materials. Full article

Foam concrete is well-appreciated for its thermal and acoustic benefits and is prepared by introducing foam into cement slurry/mortar. The current research examines the feasibility of Quarry Micro Fines (QMF), a waste generated from the quarries during sand manufacturing, as a substitute for fine aggregate in the preparation of foam concrete. During the preparation of concrete, a portion of cement is replaced with sugarcane bagasse ash (SCBA), while polypropylene (PP) fibers are added to improve the shrinkage resistance and tensile strength of the resulting concrete. A three-factor, three-level Box–Behnken Design (BBD) in Response Surface Methodology (RSM) was used to optimize the compressive strength of foam concrete, considering QMF (0%, 50%, 100%) by weight of fine aggregate, SCBA (0%, 10%, 20%) by weight of cement, and PP fiber (0.2%, 0.4%, 0.6%) by volume of foam concrete as variables. The three mixtures, including control (FC), mix with 50% QMF, 10% SCBA, and 0.4% PP fiber (F50S10F0.4), and mix with 100% QMF, 10% SCBA, and 0.4% PP fiber (F100S10F0.4), were chosen for a more in-depth investigation based on the test results. While Q50S10F0.4 achieved the highest compressive strength (6.18 MPa), Q100S10F0.4 showed the best overall performance, with low water absorption of 14.10%, porosity of 20.17%, UPV 2388 m/s, and RCPT values of 1407.96 Coulombs. The modified mixtures exhibited enhanced bonding and pore enhancement as demonstrated by scanning electron microscopy and mercury intrusion porosimetry analyses. The study highlights the effective use of QMF, SCBA, and PP fibers in producing high-performance, sustainable foam concrete. Full article

The continuous emission of persistent and bioaccumulative pollutants into aquatic environments has become a critical global issue. Among these, per- and polyfluoroalkyl substances (PFASs) are of particular concern due to their exceptional stability, extensive industrial use, and adverse impacts on ecosystems and human health. Their resistance to conventional physical, chemical, and biological treatments stems from the strength of the carbon–fluorine bond, which prevents efficient degradation under standard conditions. This review provides a concise and updated assessment of emerging advanced oxidation processes (AOPs) for PFAS remediation, with emphasis on heterogeneous photocatalysis and electrochemical oxidation. Photocatalytic systems based on In₂O₃, Bi-based oxyhalides, and Ga₂O₃ exhibit high PFAS degradation under UV light, while heterojunctions and MOF-derived catalysts improve defluorination under solar irradiation. Electrochemical oxidation—particularly using Ti₄O₇ reactive electrochemical membranes and BDD anodes—achieves near-complete mineralization with comparatively low specific energy demand. Energy consumption (E_EO) was calculated from literature data for UV- and simulated-solar-driven photocatalytic systems, enabling a direct comparison of their energy performance. Although solar-driven processes offer clear environmental advantages, they generally exhibit higher E_EO values, mainly due to lower apparent quantum yields and less efficient utilization of the incident solar photons compared to UV-driven systems. Hybrid systems coupling photocatalysis and electro-oxidation emerge as promising strategies to enhance degradation efficiency and reduce energy requirements. Overall, the review highlights key advances and future research directions toward scalable, energy-efficient, and environmentally sustainable AOP-based technologies for PFAS removal. Full article