Search Results (1,534)

The oxygen evolution reaction (OER), a key half-reaction in electrochemical water splitting, is limited by sluggish multi-electron transfer kinetics, starting extensive research into efficient, low-cost nanoscale electrocatalysts, particularly those based on nickel, cobalt, and iron, as well as mixed-metal, hybrid, and heteroatom-doped carbon-based metal-free systems, as presented here. Ni- and Co-based electrocatalysts show high efficiency for alkaline OER due to optimized nanostructures, surface modifications, heterostructure design, and multi-metal doping, which enhance activity, stability, and electronic properties. Their performance relies on precise atomic-level control of structure and synergistic interactions, enabling them to approach or rival noble-metal catalysts. Iron-based electrocatalysts are also promising due to their abundance, low cost, and flexible redox chemistry, forming active iron oxyhydroxide species during operation; however, their low conductivity requires structural and electronic optimization. Beyond Fe, Ni, and Co, copper-based compounds, zeolitic imidazolate framework-derived structures, and manganese phosphide–cerium oxide composites offer enhanced oxygen vacancies, tunable structures, and strong interfacial synergy. Furthermore, heteroatom-doped carbon materials incorporating nitrogen, phosphorus, or sulfur improve catalytic activity by modifying electronic structure, creating active sites, and enhancing charge transfer. Overall, careful control of composition, structure, and electronic properties enables the development of efficient, durable, and scalable noble-metal-free catalysts for OER. Full article

Cu₂ZnSn(S,Se)₄ (CZTSSe) is a candidate thin-film photovoltaic material; however, its performance is restricted by innate defect-induced nonradiative recombination. Low-concentration Ge doping has been identified as an efficient way to mitigate these defects, but the selenization temperature remains an important process parameter that governs the structure and optoelectronic characteristics of CZTSSe absorbers. In the present work, low-concentration Ge-doped Cu₂ZnSn_0.95Ge_0.05S₄ (CZTGS) precursor films were synthesized through a green, n-butylammonium butyrate-based solution approach. The effects of the selenization temperature (530–570 °C) on the microstructure, composition, and photovoltaic performance of Cu₂ZnSn_0.95Ge_0.05(S,Se)₄ (CZTGSSe) films and devices were comprehensively investigated. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectrometer (EDS), atomic force microscopy (AFM) were performed to comprehensively characterize the synthesized samples, and the results suggested that the selenization temperature dramatically altered the film grain growth, crystallinity, elemental retention and surface roughness. Specifically, the film that underwent selenization at 550 °C presented the best crystallinity, which was accompanied by large-scale even grains, efficient Ge⁴⁺ addition to the kesterite lattice and the lowest surface roughness. These better properties in terms of structure and composition resulted in the lowest carrier transport resistance (R_s = 8.6 Ω∙cm²), improved recombination resistance (R_j = 5.9 kΩ∙cm²), inhibited nonradiative recombination, and prolonged carrier lifetime (τ_EIS = 35.8 μs). Therefore, the resulting CZTGSSe thin-film solar cell had an 8.69% better power conversion efficiency (PCE), while its open-circuit voltage (V_OC) was 0.42 V, the fill factor (FF) was 55.51%, and the short-circuit current density (J_SC) was 37.71 mA·cm^–2. Our results elucidate the mechanism by which the selenization temperature regulates low-concentration Ge-doped kesterite devices and provide more insights into the optimization of processes for cost-effective, high-performance, and green thin-film solar cells. Full article

Phytoecdysteroids have garnered increasing interest due to their broad biological and pharmacological properties. The present study reports on the development and validation of a reliable liquid chromatography–mass spectrometry method for the detection and quantification of 20-hydroxyecdysone, turkesterone, and ponasterone. The optimized procedure improved ionization efficiency and chromatographic resolution through gradient elution using 0.1% formic acid in water and acetonitrile. Data acquisition in selective ion monitoring modes ensured high analytical precision, reproducibility, and sensitivity. The method demonstrated excellent linearity, accuracy, repeatability, and low detection limits, making it suitable for routine phytochemical and quality control applications. Application of the method to extracts from nutrient-rich superfoods, including kaniwa, spinach, quinoa, and asparagus, confirmed these plants as natural sources of phytoecdysteroids. Additionally, thirteen commercially available dietary supplements labeled as containing extracts of Rhaponticum carthamoides, Cyanotis arachnoidea, Ajuga turkestanica, or ecdysteroids were analyzed. Several products standardized to 80–95% ecdysterone contained substantially lower amounts than declared, with measured 20-hydroxyecdysone levels ranging from below the limit of detection to approximately 50 mg per capsule, whereas some non-standardized products exhibited moderate to high levels, reaching up to approximately 105 mg per capsule. Variability in turkesterone content was also observed among products marketed as standardized extracts. The method provides a simple, reliable, and accessible approach for the quantitative analysis of major phytoecdysteroids in complex plant matrices and dietary supplements. Its implementation may support phytochemical research, routine quality control, and anti-doping monitoring of ecdysteroid-containing products. Full article

The photoelectrochemical splitting (PEC) of water provides a direct route to converting solar energy into storable chemical fuels. When illuminated, a semiconductor photoelectrode can absorb light and generate electron-hole pairs, which participate in interfacial redox reactions at the semiconductor-electrolyte junction. Therefore, to achieve high-performance PEC, photoelectrodes with optimized optical absorption and charge have been explored. This review analyzes recent fabrication strategies used to design photoelectrodes for the PEC dissociation of water. Physical fabrication techniques, including pulsed laser deposition, magnetron sputtering, and physical vapor deposition, allow for precise control of film thickness, crystallinity, and defect density, critical parameters for efficient charge transport. Typically, in physical methods, reported photocurrent densities span from ~10⁻² to 10¹ mAcm⁻², depending on the semiconductor material, nanostructure design, and interfacial engineering strategies. Chemical synthesis methods, such as hydrothermal growth, successive ion layer adsorption and reaction, and microemulsion techniques, provide greater compositional flexibility and enable controlled doping, surface functionalization, and the formation of nanostructured morphologies. Finally, hybrid fabrication strategies integrate physical and chemical processes within a single synthesis framework to combine structural precision with compositional tuning capabilities. These approaches enable the development of advanced architecture such as heterojunctions, core–shell nanostructures, and catalyst-modified interfaces, which enhance light absorption and optimize interfacial transfer. Furthermore, theoretical and computational tools are here analyzed as complementary approaches that guide the rational design and optimization of photoelectrochemical materials and devices. Full article

The increasing demand for higher energy density in lithium-ion batteries has driven significant interest in layered oxide cathode materials. However, their development is hindered by an inherent trade-off between structural stability and ion transport kinetics. This compromise often manifests as a conflict between achieving high capacity, long cycle life, and excellent rate performance. Consequently, mitigating structural degradation and minimizing interfacial side reactions have emerged as core research priorities. Based on this, this review summarizes the crystal chemistry and key challenges of three main types of layered oxide cathode materials, and critically evaluates two main modification strategies: bulk doping, which enhances performance by regulating the electronic structure and suppressing phase transitions; and surface coating, which builds a protective layer at the particle–electrolyte interface to suppress side reactions and metal dissolution. Looking ahead, in terms of modification, the focus should be on multi-scale co-doping to construct a stable bulk phase structure and multi-functional coating to optimize the interface. Integrating artificial intelligence with high-throughput computation will powerfully enable the pursuit of these advanced modification strategies. This integrated approach may resolve the fundamental contradiction between energy density and stability, thereby paving a new pathway for next-generation lithium-ion batteries. Full article

Background/Objectives: Nanostructured biomaterials based on natural polymers have gained increasing attention in pharmaceutics due to their biocompatibility, multifunctionality, and diverse biomedical applications. This novel study aimed to biofabricate chitosan-doped zinc oxide nanocomposites (CS-ZnONCs) using Leucas aspera leaf extract and to evaluate their physicochemical properties and in vitro biomedical performance. Methods: CS-ZnONCs were synthesized using L. aspera leaf extract through a green precipitation approach, and the resulting nanocomposites were characterized by various spectroscopic techniques. The in vitro antioxidant, antibacterial, and anti-inflammatory activities were evaluated, while wound-healing potential was assessed using L929 fibroblast cell migration assays. Results: UV–visible analysis confirmed the formation of CS-ZnONCs, with a characteristic absorption peak at 362 nm, and FTIR spectra indicated the presence of various important functional groups. XRD results demonstrated the crystalline nature of ZnO within the chitosan matrix. Well-dispersed, quasi-spherical nanoparticles with an average size of 44 ± 3.1 nm were identified by HR-TEM, and a positive zeta potential (+9 mV) suggested considerable colloidal stability. CS-ZnONCs showed a high swelling capacity (88 ± 2.75% for 2%) and significant phytocompound release (65.38 ± 2.79% at pH 7.4). The CS-ZnONCs showed significant antioxidant activity (ABTS of 88.19 ± 1.59%), notable antibacterial efficacy against Staphylococcus aureus (18.78 ± 0.98 mm) and Escherichia coli (17.14 ± 0.96 mm), and significant anti-inflammatory activity (82.12 ± 1.47% membrane stabilization). In vitro biocompatibility and wound-healing assays revealed significant cytocompatibility in Vero cells, with 98.75 ± 1.17% cell viability observed, whereas the fibroblast migration assay demonstrated near-complete wound closure (96.55 ± 6.46%). Conclusions: The green-synthesized CS-ZnONCs exhibit favorable physicochemical properties, biocompatibility, and multifunctional biological activities, supporting their potential as a promising sustainable biomaterial nanomedicine for pharmaceutical formulations, wound healing, and regenerative medicine applications. Full article

To address the capacity decay of NCM811 caused by microcracks and cation disorder during cycling, La, Al, and F tri-doped micron-sized single-crystal NCM811 material with a LiNbO₃ coating was synthesized via a facile co-solvent method. Using a mixed glucose–urea thermal solution as the reaction medium, metal salts were incorporated, followed by step-wise sintering, ball-milling, heat treatment, and wet-chemical coating. This approach enables atomic-level precursor mixing and ensures homogeneous element distribution. La³⁺ enlarges the lithium layer spacing to enhance ion diffusion and Al³⁺ suppresses Ni³⁺ reduction to Ni²⁺, mitigating cation mixing and improving conductivity, while F⁻ stabilizes the crystal structure via its strong electronegativity. The LiNbO₃ coating protects the interface from electrolyte attack, and the single-crystal morphology effectively suppresses microcracking. Compared to unmodified single-crystal NCM811 prepared identically, the modified material exhibits reduced cation disorder, improved crystallinity, and superior thermal stability. Electrochemical tests in half-cells with 1 M LiPF₆/(EC/EMC/DMC) electrolyte (2.8–4.3 V) show an initial discharge capacity of 208.32 mAh/g at 0.1 C and 194.05 mAh/g at 1 C. After 200 cycles at 1 C, the capacity retention remains at 92.21%, exceeding the market average. Rate performance is also notably enhanced, with the 5 C discharge capacity increasing from 141.12 mAh/g (unmodified) to 166.81 mAh/g, demonstrating improved kinetics and structural stability. Full article

This work investigates the influence of hybrid NiO–SiO₂ nanoparticles on the engine behavior of biodiesel derived from waste sunflower oil and evaluates the experimental outcomes using a data-driven modeling approach. Biodiesel was produced via transesterification and doped with nanoparticles at concentrations of 50, 75, and 100 ppm. Performance and emission tests were conducted on a single-cylinder diesel engine operating at constant speed under varying loads. Specific fuel consumption, brake thermal efficiency, CO, HC, NO_x, smoke opacity, and exhaust gas temperature were recorded and analyzed. The incorporation of nanoparticles improved combustion quality and contributed to substantial reductions in harmful emissions. The WSOB20 blend containing 100 ppm NiO–SiO₂ provided the most balanced results, decreasing CO, HC, and smoke emissions by 39.50%, 39.40%, and 35.20%, respectively, relative to diesel fuel, while preserving competitive thermal efficiency. A linear regression model developed for CO prediction produced a low mean squared error (1.08 × 10⁻⁵), indicating strong predictive capability. The findings confirm that hybrid nanoparticle additives can enhance biodiesel performance while supporting accurate emission forecasting. Full article

Single-Event Burnout (SEB) is one of the most critical failure mechanisms in silicon power MOSFETs operating in radiation environments, particularly under heavy-ion irradiation, and often limits device operation through excessive voltage derating. In this work, SEB robustness of a silicon VDMOS power device is investigated using detailed electro-thermal transient simulations. The study evaluates two complementary device-level modifications: the introduction of a buffer layer between the epitaxial layer and the substrate, which has been reported in the past, and a new approach considering the incorporation of a novel highly doped boron BOX implant within the P-body region. Heavy-ion impacts are simulated using a physically based model implemented in SENTAURUS TCAD, accounting for ion energy deposition, impact position, and thermal effects. The results show that the buffer layer increases the second breakdown voltage and can suppress high-current operating points, while the BOX implant raises the parasitic BJT activation threshold by reducing the P-body resistance. When combined, both modifications lead to a significant reduction in the peak temperature reached during after-impact transients, without introducing measurable degradation of static electrical characteristics. These results demonstrate that combining buffer layer engineering with localized P-body resistance reduction is an effective strategy to improve SEB robustness in silicon VDMOS power devices without relying on excessive derating. Full article

The pursuit of high-energy-density cathode materials has positioned LiNiO₂ as a promising candidate due to its high theoretical capacity. However, its practical application is hindered by structural instability, cation mixing, and sluggish Li-ion mobility. This study presents a strategic co-doping approach to enhance the electrochemical performance of R3m-structured LiNiO₂ by introducing Na at the Li site and Nb/Al/W at the Ni site. First-principles calculations based on density functional theory (DFT), combined with the bond valence sum energy (BVSE) method, were employed to evaluate the structural, electronic, and transport properties of the doped systems. The optimized lattice parameters reveal that co-doping induces lattice expansion and suppresses cation disorder, thereby improving structural integrity. Formation energy validates the thermodynamics of the modified structures. Furthermore, BVSE-based ion migration mapping shows that Na/Nb and Na/Al co-doping significantly broadens Li-ion diffusion pathways and lowers migration barriers compared to pristine LiNiO₂. These results demonstrate that dual-site doping is an effective strategy to overcome intrinsic limitations of Ni-rich layered oxides, offering a rational design route cathode for next-generation Li-ion battery. Full article

Most of the existing carbon dot (CD)-based afterglow materials are limited to a single emission mode of either room-temperature phosphorescence (RTP) or delayed fluorescence (DF), which makes it difficult to meet the application requirements of advanced anti-counterfeiting and multi-level information encryption. Therefore, the development of CD-based composite materials with multi-mode afterglow emission, long lifetime and high stability holds significant research significance and application value. In this study, long-afterglow manganese/nitrogen co-doped CDs@boric acid (BA) composites (Mn, N-CDs @BA) are successfully prepared, and their optical properties and emission mechanism are clarified. The results demonstrate that the Mn, N-CDs @BA composites exhibit wavelength-dependent dual-afterglow emission characteristics of RTP and DF. Under 254 nm ultraviolet (UV) light excitation, they exhibit DF emission with an average lifetime of 903.36 ms. Under 365 nm UV light excitation, RTP emission with an average lifetime of 354.43 ms is observed. Moreover, the afterglow color exhibits time dependence. Based on the triple emission modes (fluorescence, RTP and DF) of the Mn, N-CDs @BA composites, optical patterns were designed and fabricated, and counterfeit-resistant and unclonable anti-counterfeiting and high concealment information encryption were successfully achieved. This work develops a potentially feasible approach for next-generation advanced optical anti-counterfeiting and information encryption systems. Full article

Insulated-gate bipolar transistor (IGBT) power modules suffer efficiency degradation at elevated operating junction temperatures. The thermal sensitivity of the collector–emitter saturation voltage (V_CEsat) induces thermal stress imbalance, constraining system efficiency and reliability. A multi-resistor cascade network model for carrier-storage trench-gate IGBTs (CS-IGBTs) is established. The simulation results agree with the measurements within 10% error. The model decomposes the temperature coefficient contributions of individual structural regions. Analysis reveals that the drift region resistance dominates the V_CEsat temperature coefficient. Based on this finding, a co-doping strategy is proposed through simultaneously increasing the doping concentration in the carrier-storage layer and P⁺ collector. This approach reduces the temperature sensitivity of carrier mobility in the drift region, thereby optimizing V_CEsat’s temperature sensitivity. For the fabricated 1200 V/40 A CS-IGBT, the V_CEsat temperature coefficient decreases from 2.38 mV/K to 1.76 mV/K over 300 K to 450 K, which represents a 25.4% reduction. The total switching loss at 450 K decreases from 9.32 mJ to 8.70 mJ, achieving a 6.7% improvement. This device-level optimization suppresses V_CEsat’s temperature sensitivity and switching losses, enhancing efficiency in high-temperature power module applications. Full article

To enhance the electrochemical performance of NiMn layered double hydroxides (LDH), this study explores the Ce-doped NiMn-LDH (CeNiMn-LDH) as a cathode material for supercapacitors. In the CeNiMn-LDH structure, partial substitution of Ni/Mn ions by Ce increases the number of active sites, facilitates electron transfer, and improves current density, leading to a significant enhancement in the electrochemical properties compared with NiMn-LDH. Experimental results show that the 0.3CeNiMn-LDH electrode delivers excellent electrochemical performance, achieving a specific capacitance of 1928.16 F/g at a current density of 1 A/g. Furthermore, an assembled CeNiMn-LDH//AC asymmetric supercapacitor exhibits an energy density of 36.36 Wh/kg and a power density of 850 W/kg at 1 A/g. Therefore, the strategy of employing CeNiMn-LDH offers an effective technical approach for improving the electrochemical performance of supercapacitor cathode materials, demonstrating considerable potential for practical applications. Full article

A high-entropy strategy has emerged as a promising approach to enhance the functional properties of piezoelectric ceramics for biomedical applications. For this reason, we have designed two novel high-entropy ceramics, (Bi_1/2Na_1/2)(Zr_1/3Sn_1/3Ti_1/3)O₃(BNZST) and (Bi_1/2Na_1/2)(Zr_1/4Sn_1/4Hf_1/4Ti_1/4)O₃(BNZSHT), which were synthesized via a two-step solid-state reaction. The phase structure, surface morphology, biocompatibility, and in vitro bioactivity were assessed. The results showed both ceramics adopted perovskite structures. BNZST and BNZSHT ceramics had relatively even crystallite sizes and element distribution, as well as achieving piezoelectric (d₃₃ ≥ 78 pC/N) properties. In vitro tests confirmed a high relative cell growth rate (RSG, >80%) after co-culturing BNZST or BNZSHT ceramic with murine fibroblasts L929 for more than 3 days. In particular, the surface with electric charge enhanced L929 with more extensive, widespread, and dense proliferation for the BNZST ceramic compared to ceramics without BNZST or unpolarized BNZST. The above indicated that multi-element doping and entropy stabilization established a novel pathway for developing a high-entropy bio-piezoelectric ceramics with high biocompatibility and bioactivity, providing the possibility for their use in bone repair materials. Full article

Sulfonamide antibiotics (SAs) are ubiquitous and persistent organic contaminants in aquatic and soil ecosystems due to their extensive application and high structural stability, causing rising environmental hazards. Conventional treatment approaches, generally based on physical adsorption or biological processes, remain limited in achieving efficient and stable removal as well as deep molecular modification of SAs. In recent years, modified biochar has developed as a flexible environmental functional material incorporating adsorption and reaction regulation capabilities, owing to its customizable pore structure, surface chemistry, and electronic characteristics. This study comprehensively highlights current achievements in the adsorption and degradation of sulfonamide antibiotics by modified biochar, with specific emphasis on modification techniques, structural modulation, structure–performance connections, and interfacial reaction processes. Through physical activation, heteroatom doping, defect engineering, and metal integration, biochar has developed from a traditional adsorbent into a carbon-based interfacial reactor capable of pollutant adsorption, molecular activation, and directed transformation. Surface-confined reaction interfaces, where π–π interactions, hydrogen bonding, electrostatic interactions, and metal coordination cooperatively control adsorption and transformation processes, are primarily responsible for the elimination of SAs. Moreover, the dual functions of modified biochar in driving both radical and non-radical pathways are explored, showing the vital importance of interfacial electronic structure modulation and electron-transfer mechanisms in influencing reaction efficiency and selectivity. The impact of sulfonamide molecular configurations, ambient circumstances, and concomitant chemicals on removal performance are also explored. Unlike previous reviews that mainly summarize adsorption efficiency or oxidant activation systems separately, this work integrates structural modulation, interfacial electronic regulation, and bond-selective transformation mechanisms into a unified structure–chemistry–reactivity framework. By correlating sulfonamide molecular configuration with biochar electronic structure, this review provides a mechanistic roadmap for the rational design of next-generation catalytic biochar systems. Finally, key challenges related to structural controllability, long-term stability, and engineering scalability are identified, and future research directions are proposed to support the rational design of high-performance biochar materials and the practical control of sulfonamide antibiotic pollution. Full article