Search Results (170)

Underground hydrogen storage (UHS) in carbonate and siliceous formations presents a promising solution for managing intermittent renewable energy. However, experimental data on hydrogen–rock interactions under representative subsurface conditions remain limited. This study systematically investigates mineralogical and petrophysical alterations in dolomite, calcite-rich limestone, and quartz-dominant siliceous cores subjected to high-pressure hydrogen (100 bar, 70 °C, 100 days). Distinct from prior research focused on diffraction peak shifts, our analysis prioritizes quantitative changes in mineral concentration (%) as a direct metric of reactivity and structural integrity, offering more robust insights into long-term storage viability. Hydrogen exposure induced significant dolomite dissolution, evidenced by reduced crystalline content (from 12.20% to 10.53%) and accessory phase loss, indicative of partial decarbonation and ankerite-like formation via cation exchange. Conversely, limestone exhibited more pronounced carbonate reduction (vaterite from 6.05% to 4.82% and calcite from 2.35% to 0%), signaling high reactivity, mineral instability, and potential pore clogging from secondary precipitation. In contrast, quartz-rich cores demonstrated exceptional chemical inertness, maintaining consistent mineral concentrations. Furthermore, Brunauer–Emmett–Teller (BET) surface area and Barrett–Joyner–Halenda (BJH) pore distribution analyses revealed enhanced porosity and permeability in dolomite (pore volume increased >10×), while calcite showed declining properties and quartz showed negligible changes. SEM-EDS supported these trends, detailing Fe migration and textural evolution in dolomite, microfissuring in calcite, and structural preservation in quartz. This research establishes a unique experimental framework for understanding hydrogen–rock interactions under reservoir-relevant conditions. It provides crucial insights into mineralogical compatibility and structural resilience for UHS, identifying dolomite as a highly promising host and highlighting calcitic rocks’ limitations for long-term hydrogen containment. Full article

Based on drilling, core and seismic data, combined with the regional tectonic sedimentary evolution background, the sedimentary environment of the Triassic carbonate rocks in the Mangeshlak Basin was studied. A sedimentary facies model of this set of carbonate rocks was established. Research has shown that the Mangeshlak Basin underwent a complete large-scale marine transgression–regression sedimentary evolution process during the Triassic. During the early to middle Triassic, seawater gradually invaded the northwest region of the basin from northwest to southeast and gradually regressed in the late Middle Triassic. In the lower part of the Triassic carbonate rocks, the primary components are developed granular limestone or dolomite with oolitic structures, interspersed with a small amount of thin mudstone, which is a good reservoir; the upper part of the Triassic is mainly composed of sedimentary mudstone and mudstone, which can form good sealings. The hill-shaped reflections of the platform edge facies, along with the high-frequency, strong-amplitude, and moderately continuous reflections within the restricted platform interior, are clearly visible on the seismic profile. These features are consistent with the sedimentary environment and lithofacies characteristics revealed by drilling data along the profile. Drilling and seismic data revealed that the sedimentary environment of the early and middle Triassic in the basin is mainly composed of shallow water platform edges and restricted platforms, as well as carbonate rock slopes and open non-marine shelves in deep water areas. A sedimentary facies model of the Triassic carbonate rock segment in the basin was established, comprising restricted platforms, platform edges, carbonate rock slopes, and non-marine shelves. Unlike the modified Wilson marginal carbonate rock platform model, the carbonate rock platform edge in the Mangeshlak Basin does not develop reef facies. Instead, it is mainly composed of oolitic beach (dam) sediments, making it the most favorable sedimentary facies zone for the Triassic reservoir development in the basin. Full article

Türkiye hosts a wide variety of barite deposits that can be broadly classified into two major groups based on their tectonic settings: magmatism-associated and passive margin-hosted deposits. The magmatism-associated deposits include Kızılcaören (F + Ba + REE + Th, Beylikova–Eskişehir), Kirazören (Bulancak–Giresun), and Karacaören (Mesudiye–Ordu). The Kızılcaören deposit formed in relation to the emplacement of a late Oligocene carbonatitic sill, while the Kirazören and Karacaören deposits are associated with the Cretaceous Pontide magmatic arc. Passive margin-hosted deposits occur within various Paleozoic sedimentary lithologies—such as metasandstone, shale, schist, and limestone—and are found in the Taurides and the Arabian Platform. These deposits occur as either concordant or discordant veins. This barite belt extends from Şarkikaraağaç (Isparta), through Hüyük (Konya) and Alanya (Antalya), to Silifke (Mersin), Tordere (Adana), Önsen, Şekeroba (Kahramanmaraş), and Hasköy (Muş). The Paleozoic deposits represent the major barite resources of Türkiye, with an annual production of approximately 300,000 metric tons. Smaller deposits around Gazipaşa (Antalya) contain minor Pb-Zn sulfides. Mesozoic barite deposits are hosted in Triassic dolomites and are associated with Pb-Zn mineralization in the Hakkari region of the Arabian Platform. Pb and Sr isotope data indicate that the barium in these deposits was derived from ancient continental crust. The isotopic compositions of both concordant (stratabound) and discordant (vein-type) barites are generally homogeneous. In northwestern Türkiye, the Sr isotope compositions of the barite deposits align well with those of the Oligocene carbonatite host complex. The ⁸⁷Sr/⁸⁶Sr isotope ratio of the Kızılcaören deposit (0.706‰) is the least radiogenic among Turkish barite deposits, suggesting a mantle contribution. The Kirazören deposit in the Pontide magmatic arc follows with a slightly higher ratio (0.707‰). Triassic barites from the Hakkari region yield ⁸⁷Sr/⁸⁶Sr values around 0.709‰, slightly more radiogenic than coeval seawater. Paleozoic barite deposits show the most radiogenic ⁸⁷Sr/⁸⁶Sr values, including Aydıncık (0.718‰), Şarkikaraağaç (0.714‰), Hasköy (0.713‰), Kahramanmaraş (0.712‰), Tordere, and Hüyük (both 0.711‰), consistent with their respective host rocks. The elevated radiogenic Pb and Sr isotope values in the passive margin-hosted deposits suggest that the barium originated from deeper, barium-enriched rocks, whereas stable sulfur isotope data point to a marine sulfur source. Moreover, Sr and S isotopic signatures indicate that the Paleozoic sediment-hosted deposits formed in association with cold seeps on the seafloor, resembling modern analogs. In contrast, the Mesozoic Karakaya deposit (Hakkari) represents a typical vent-proximal, sediment-hosted deposit with no magmatic signature. Full article

It has been found in engineering practice that the degree of rockburst risk increases when roadway excavation occurs near the stratigraphical boundary of different lithologies. This study uses the 1276 m deep-buried roadway of a lead–zinc mine in Yunnan, China, as its engineering background. Based on a numerical analysis of this case, it investigates the mechanical behavior of surrounding rocks in different lithological formations and explores the causes of excavation-induced rockburst. Additionally, by changing the excavation strategy in a numerical simulation, the influence of the direction of roadway excavation on the degree of rockburst risk in the construction of different lithological formations is assessed. The results are summarized as follows: (1) When the tunnel passes from the C₁b stratum (limestone) to the D₃zg stratum (dolomite), an abnormal stress zone forms in the roof rock strata of the D₃zg stratum (the lower plate of the stratum boundary). The rockburst risk level was evaluated by introducing the numerical rockburst index in this abnormal stress zone, which aligns closely with on-site rockburst investigation results. The rockburst risk is the greatest in the abnormal stress zone, which provides an external energy storage environment for the development of rockburst disasters. (2) Near the stratum boundary, the rockburst risk level when excavating from the D₃zg stratum to the C₁b stratum is greater than that when excavating from the C₁b stratum to the D₃zg stratum. The direction of tunnel excavation significantly affects the rockburst risk level during construction that crosses different lithological strata. These findings can provide a theoretical basis for the construction design of similar underground projects. Full article

This study presents a chemical and mineralogical analysis of stone samples from Jošanica quarry collected from three different locations—Field A, Field B, and Field C. Mineralogical analyses were conducted using XRD analysis. The analyses showed that calcite was the dominant mineral in most of the samples, while dolomite was significantly present in some of the samples. Chemical analysis revealed that calcium was dominant in samples 2 (Field B), 3a, and 3b (Field C), with only negligible amounts of magnesium. In contrast, samples 1a, 1b, and 1c (Field A) contained a significant amount of magnesium. Based on the MgCO₃ content, the amount of dolomite in the stone samples was calculated. The content of CaCO₃ in its bound form in dolomite was lower than that in the stone samples, indicating that CaCO₃ was present in another form. According to the dolomite content, samples 1a, 1b, and 1c (Field A) are classified as limestone–dolomite, while samples 2 (Field B), 3a, and 3b (Field C) are classified as limestone due to their high calcium carbonate content. The results of a mineralogical analysis confirmed the results of the chemical analysis. Full article

The Dolomites (European Alps) are a UNESCO World Heritage Site known to harbor distinctive communities of carabid beetles adapted to high-altitude environments, whose composition is shaped mainly by landform and habitat type. We aimed to assess the conservation priority of carabid beetle communities in the Brenta mountain group (Italy). We used the Index of Natural Value (INV), based on the relative frequencies and abundances of highly specialized Alpine species, as a proxy of the sensitivity to disturbance, and, thus, to the vulnerability of the carabid beetle communities to extinction. We used information on Natura 2000 habitat cover to produce a map for identifying areas of the Brenta Dolomites inhabited by the carabid beetle communities most relevant for conservation. We also report on the main differences in terms of species composition between the investigated communities. We found a positive correlation between vulnerability and altitude. Specifically, the most vulnerable communities were recorded in high-altitude habitat types (limestone cliffs and pavements, calcareous and calcschist screes, and alpine calcareous grasslands). Alkaline fens resulted in having the least vulnerable community, while those in all other habitats (bush and forests) were found to have intermediate levels of vulnerability. Full article

With the intensive development of oil and gas resources leading to a rapid increase in abandoned wells, sealing failures may cause oil and gas leakage and environmental pollution. Systematically investigating the temperature distribution patterns of thermite melting in open-hole abandoned wells under various factors is critical for effective plugging. This study overcomes the limitations of traditional single heat conduction models by integrating thermite reaction kinetics, phase change latent heat, and thermal–fluid–solid multi-field coupling effects, establishing a thermal–fluid–solid coupling model for thermite melting in open-hole abandoned wells. This model provides theoretical guidance for the effectiveness of plugging operations and temperature control during operations. The model was validated through thermite melting experiments: the simulated expansion of the sandstone borehole diameter was 9.8 mm, with a 5.5% error compared to the experimental value of 9.29 mm; and the simulated axial extension at the well bottom was 18.9 mm, with a 4.7% error compared to the experimental value of 17.19 mm, confirming the model’s accuracy. The influence of different lithologies and initial downhole temperatures on the temperature distribution in the open-hole section of abandoned wells under identical conditions was analyzed. The results show that the ultimate melting thicknesses of dolomite, limestone, and granite are 0.0354 m, 0.0350 m, and 0.0234 m, respectively, indicating superior plugging effects in dolomite and limestone. In the initial reaction stage (stage a), the phase change thickness of limestone exceeded that of dolomite by 59.78%, demonstrating better thermite melting and sealing efficacy in limestone. Additionally, model analysis reveals that the initial downhole temperature has a minimal impact on the temperature distribution of thermite melting in open-hole abandoned wells. Full article

The Dolomite reservoir of the Maokou Formation is rich in gas resources in the central Sichuan Basin. Acid fracturing is an important technical means to improve reservoir permeability and productivity. The interaction mode of the dolomite and limestone acid system will affect the effect of reservoir reconstruction. In order to clarify the influence of complex structure on fracture morphology, we explore the fracturing effect of different acid systems. Physical simulation experiments of true triaxial acid fracturing were carried out with two acid systems and downhole full-diameter cores. The experimental results show: (1) After the carbonate rock is subjected to acid fracturing using a “self-generated acid + gel acid” system, the fracture pressure drops significantly by up to 60%. The morphology of the acid-eroded fractures becomes more complex, with an increase in geometric complexity of about 28% compared to a single acid solution system. It is prone to form three-dimensional “spoon” shaped fractures, and the surface of the acid-eroded fractures shows light yellow acid erosion marks. Analysis of the acid erosion marks indicates that the erosion depth on the fracture surface reaches 0.8–1.2 mm, which is deeper than the 0.2 mm erosion depth achieved with a single system. (2) Acid solution is difficult to penetrate randomly distributed calcite veins with a low porosity and permeability structure. When the fracture meets the calcite vein, the penetration rate of acid solution drops sharply to 15–20% of the initial value, resulting in a reduction of about 62% of the acid erosion area in the limestone section behind. And the acid erosion traces in the limestone behind the calcite vein are significantly reduced. The acid erosion cracks are easy to open on the weak surface between dolomite and limestone, causing the fracture to turn. (3) The results of field engineering and experiment are consistent, and injecting authigenic acid first in the process of reservoir reconstruction is helpful to remove pollution. The recovery rate of near-well permeability is more than 85% with pre-generated acid. Reinjection of gelled acid can effectively communicate the natural weak surface and increase the complexity of cracks. The average daily oil production of the completed well was increased from 7.8 m³ to 22.5 m³, and the increase factor reached 2.88. Full article

Carbonate rock slopes in reservoir environments are increasingly exposed to dissolution-induced deterioration due to water level fluctuations. However, the influence of internal structures—particularly calcite veins—on dissolution behavior remains inadequately understood. The acid-induced dissolution of limestone by a sulfuric acid solution leads to the removal of soluble minerals and changes to the rock structure. Natural variation in rock structures—particularly in the presence, density, and morphology of calcite veins—can significantly affect the dissolution process and its outcomes. In this study, we obtained three types of Triassic limestone from the same host rock but with varying vein structures from the Three Gorges Reservoir area. Cylindrical rock specimens were prepared to investigate the acid-induced dissolution behavior of limestone in a sulfuric acid solution. We identified and analyzed the macrostructures on the rock specimens before and after the interaction. Additionally, SEM was employed to observe the microstructures of the specimens before and after the acid-induced dissolution, and fractal dimension analysis was conducted on the SEM images to quantify surface complexity. Furthermore, we used a focused ion beam–scanning electron microscope (FIB-SEM) with an automatic mineral identification and characterization system, as well as mineral roundness calculation, for mineral identification and analysis. Based on the experiments and analyses, we determined the following: The contact surfaces between the host rock and the calcite veins increase the dissolution areas between the limestone and the sulfuric acid solution, intensifying the dissolution reactions, enhancing the connectivity of the original microstructural planes, and generating new, highly extended dissolution fissures. The calcite veins facilitate the entry of sulfuric acid solution into the limestone, intensifying the dissolution of the edges and corners of dolomite and resulting in the gradual rounding of dolomite shapes. Quantitatively, the limestone with dense, fine calcite veins exhibited the most severe dissolution, with water absorption rates nearly twice as high as the non-veined samples (0.13% vs. 0.07%), a 2.2% reduction in fractal dimension, and a 19.53% increase in dolomite roundness with the 1 ≤ R ≤ 3 interval, indicating significantly enhanced surface complexity and mineral reshaping. In summary, the presence of more calcite veins, regardless of their width, leads to more severe rock dissolution. Full article

The Silvermines Pb-Zn-Ag-Ba orebodies comprise vein, replacement, cross-cutting and stratiform mineralization mostly hosted in Lower Carboniferous limestones in the vicinity of a major ENE and E-W trending normal fault array and represent a classic example of Irish-Type Zn-Pb mineralization. Historically the deposits have been exploited at various times, but the major limestone-hosted Zn-Pb-Ba mineralization was not discovered until the 1960s. Structurally controlled crosscutting vein and breccia mineralization represent pathways of hydrothermal fluids escaping from the Silvermines fault at depth that exhaled and replaced shallowly buried Waulsortian limestones creating the larger stratiform orebodies such as the Upper G and B-Zones. The B-Zone, comprising a pre-mining resource of 4.64 Mt of 4.53% Zn, 3.58% Pb, 30 g/t Ag has a locally highly variable host mineralogy dominated by pyrite, barite, siderite, within dolomitic and limestone breccias with local silica-haematite alteration. A small, highly unusual pod of very high-grade Ag-rich mineralization in the B-Zone, the 4611 Pod, discovered in 1978, has not been previously documented. Unpublished records, field notes, and mineralogical and chemical data from consultant reports have been assimilated to document this interesting and unusual occurrence. The pod, representing an irregular lens of mineralization ca 2 m thick and representing 500 t, occurs within the B-Zone orebody and comprises high grade Zn and Pb sulfides with significant patches of proustite-pyrargyrite (ruby silvers) and a host of associated Pb, Ag, Sb, As, Cu, Ge sulfide minerals, including significant argyrodite. Although evidence of any distinct feeder below the pod is lacking, the nature of the pod, its unusual mineralogy and its paragenesis suggests that it represents a small, possibly late source of exotic hydrothermal fluid where it entered the B-Zone stratiform mineralizing system. Full article

The transition zone between a shallow-water delta and tidal flat is characterized by a high degree of mixed siliciclastic–carbonate sedimentation. There are frequent lateral and vertical variations in sandstone, dolostone, limestone, and mixed siliciclastic–carbonate rock (MSR); however, their influence on reservoir quality remains uncertain. Member B of the Asmari Formation (Asmari B) in Iraq’s C Oilfield was deposited in a remnant ocean basin formed by the closure of the Neo-Tethys Ocean. During the Oligocene–Miocene, frequent exposure of the Arabian Shield provided intermittent sediment sources to the study area. Under shallow water and relatively arid conditions, widespread mixed sedimentation of siliciclastic sand and dolomitic components occurred. Taking Asmari B as a case study, this research employs core and thin-section observations, trace element analyses, and quantitative mineralogical interpretations of logging data to investigate the characteristics of mixed sedimentation and to evaluate its impact on reservoir quality. Four key aspects were identified: (1) Four main types of mixed lithofacies developed in Member B of the Asmari Formation, namely sandstone-bearing dolomite, dolomitic sandstone, dolostone-bearing sand, and sandy dolostone. These lithofacies were deposited in the transition zone between distributary channels and intertidal zone with different water depths. As the terrigenous input decreased, the water depth for sand-bearing facies increased. In particular, sandy dolostone was predominantly formed in subtidal settings under the influence of storm events. (2) MSRs are categorized based on the proportion of the minor component into high and low mixing degrees. Based on mineral compositions interpreted from well logging data, the mixing degree of MSRs was characterized by the thickness ratio, using the thickness of high- and low-mixing-degree MSRs relative to the total thickness of the formation. The MSRs mainly developed in the B1, B2, B3-1, B3-2, and B4 sublayers, where moderate provenance supply facilitated the high mixing of terrigenous clastic and carbonate components. (3) The pore and throat patterns of MSR reservoirs change with the mixing degree index. When the dolomite content in sandstone exceeds 25%, the pore–throat structure changes significantly. A small amount of sand in dolostone has little effect on the pore and throat. Sandy dolostone exhibits the poorest reservoir quality. (4) Mixed sandstone reservoirs are distributed on both sides of the distributary channels and mouth bar. The dolostone-bearing sand reservoirs are distributed in the transition zone between the sandy flat and dolomite flat. Sandy dolostone is mainly thin and isolated due to the influence of storm events. This study provides guidance for understanding the development patterns of MSR reservoirs under similar geological settings, facilitating the next step of oil and gas exploration in these special reservoirs. Full article

The effects of climate change are particularly pronounced in cities, where urban green infrastructure—such as trees, parks, and green spaces—plays a vital role in both climate adaptation and mitigation. This study assesses the carbon sequestration potential of urban forests in Budapest, the capital city of Hungary, which lies at the intersection of the Great Hungarian Plain and the Buda Hills, and is traversed by the Danube River. The city is characterized by a temperate climate with hot summers and cold winters, and a diverse range of soil types, including shallow Leptosols and Cambisols in the limestone and dolomite hills of Buda, well-developed Luvisols and Regosols in the valleys, Fluvisols and Arenosols in the flood-affected areas of Pest, and Technosols found on both sides of the city. The assessment utilizes data from the National Forestry Database and the Copernicus Land Monitoring Service High Resolution Layer Tree Cover Density. The results show that Budapest’s urban forests and trees contribute an estimated annual carbon offset of −41,338 tCO₂, approximately 1% of the city’s total emissions. The urban forests on the Buda and Pest sides of the city exhibit notable differences in carbon sequestration and storage, age class structure, tree species composition, and naturalness. On the Buda side, older semi-natural forests dominated by native species primarily act as in situ carbon reservoirs, with limited additional sequestration capacity due to their older age, slower growth, and longer rotation periods. In contrast, the Pest-side forests, which are primarily extensively managed introduced forests and tree plantations, contain a higher proportion of non-native species such as black locust (Robinia pseudoacacia) and hybrid poplars (Populus × euramericana). Despite harsher climatic conditions, Pest-side forests perform better in carbon sink capacity compared to those on the Buda side, as they are younger, with lower carbon stocks but higher sequestration rates. Our findings provide valuable insights for the development of climate-resilient urban forestry and planning strategies, emphasizing the importance of enhancing the long-term carbon sequestration potential of urban forests. Full article

In the western Tarim Basin, Carboniferous granular dolostones deposited on a carbonate platform contain a small amount of terrigenous materials of sand-size fraction, agglomerated clay minerals, or similar phases. However, the role of terrigenous materials on dolomitization is still unclear. The aim of this study was to reveal the dolomitization mechanism. The granular dolomites have small crystal size, earthy yellow color, and fabric-retentive texture, with relatively good order. These features indicate dolomites precipitated during early diagenesis. The ratio of rare earth elements (RREs) abundance of the stable isotopes ⁸⁷Sr/⁸⁶Sr relative to Post-Archean Australian Shale (PAAS) normalized patterns was used to study the source of the dolomitizing fluids. The composition of REEs is characterized by heavy rare earth (HREE) enrichment (average Nd_SN/Yb_SN = 0.83). There is a positive (La/La*)_SN anomaly and slightly positive (Gd/Gd*)_SN and (Y/Y*)_SN anomaly; δ¹⁸O of seawater in fractionation equilibrium with granular dolostones was from −2.8‰ to 1.7‰ PDB, implying the dolomitizing fluid was contemporary, slightly evaporated seawater. The granular dolostones on the relatively thick shoals were subject to subaerial exposure before pervasive dolomitization, with evidence that the input of detrital kaolinite predated the formation of dolomites. Higher ⁸⁷Sr/⁸⁶Sr values and ∑REE in granular dolostones than the values in equivalent limestones indicate that dolomitization was related to terrigenous materials. Within the terrigenous materials, the negative-charged clay minerals may have catalyzed the dolomitization, resulting in dramatically decreased induction time for precipitation of proto-dolomites. A greater amount of terrigenous materials occurred on the shoals at the sea level fall, resulting from enhanced river entrenchment and downcutting. As a result, after subaerial exposure, the penesaline water flow through the limy allochems sediments lead to dolomitization, with the catalysis of illite on relatively thick shoals. Full article

The Zaghouan Fluorite Province (ZFP) encloses F-Ba(Pb-Zn) ores hosted within Jurassic carbonate series, in northeastern Tunisia. Critical breakthroughs on the Jebel Stah fluorite deposits, an MVT-style F-mineralization, have been made within the Lower Jurassic limestones along the Zaghouan Fault, which is a major target for mineralization. This study presents the first REE-Y analyses conducted by LA-ICP-MS on fluorites in Tunisia, and specifically on the fluorites of Jebel Stah deposit. This analytical technique provides highly accurate insights into the geochemical regime of mineralizing fluids and the related scavenging sources. Distinct geochemical characteristics between two fluorite generations (G1 and G2) were revealed. Fluorites (Fl2) from the early generation (G1) showed low ΣREE + Y (36.3 and 39.73 ppm, respectively). When normalized to chondrites, early fluorite G1 displayed a bell-shaped REE + Y pattern with a depletion in LREE relative to HREE and a slight MREE hump. Late fluorite (Fl3) generation (G2) displayed higher ΣREE + Y concentrations (77.43 ppm), but an almost similar REE pattern. Ce/Ce* ratios demonstrated strong negative Ce anomalies in all fluorites, while Eu/Eu* ratios indicated weak negative Eu anomalies. The positive Y anomaly observed in the REE + Y patterns of fluorites G1 and G2 suggests Y-Ho fractionation in the fluid system. Moreover, significant degrees of differentiation between terbium (Tb) and lanthanum (La) have been observed in all fluorite samples. The plot of fluorites from both fluorite generations on the Tb/La–Tb/Ca diagram gives evidence of the sedimentary hydrothermal origin of the ore-forming fluids in the Jebel Stah F-deposit. Sr isotopes show that the mineralizing fluids are radiogenic and deeply sourced basinal brines, whereas the small variation in ⁸⁷Sr/⁸⁶Sr ratios suggests a similar source for Sr in fluorites G1 and G2. These results allow us to conclude that the economic fluorite (G1) ore of Jebel Stah was deposited due to the interaction of the deeply sourced hydrothermal fluid with the carbonated host rocks (dolomitization, an increase in pH, and Ca activity), whereas the late fluorite (G2) is an accessory and could have resulted from the mixing of the hydrothermal fluid with shallow meteoric waters. Full article