Search Results (28)

This paper investigates the microstructural evolution and mechanical performance of dissimilar friction stir-welded (FSW) T-joints produced from AA5083-H111 and AA7020-T651 aluminium alloys. The study focuses on the effects of tool rotational speed, traverse speed, and tool pin length on joint quality and mechanical strength. Welding experiments were conducted at two rotational speeds (400 and 700 rpm) and three traverse speeds (50, 100, and 200 mm/min) using two Triflute tools with pin lengths of 4.8 mm and 6.8 mm. The welded joints were examined by macro- and microstructural observations, microhardness measurements, and bending tests performed under pull-out loading conditions. The results showed that the use of the longer pin significantly improved material mixing and reduced the extent of internal defects, resulting in higher bending strength. Increasing the traverse speed improved the mechanical performance, whereas an excessively high rotational speed reduced joint strength due to increased heat input and unfavourable microstructural changes. Microhardness profiles showed no reduction in hardness within the heat-affected zones relative to the base materials and indicated localised hardening in the stir zone. For the investigated material configuration and tool geometries, the highest joint strength was obtained at a rotational speed of 400 rpm and a traverse speed of 200 mm/min using the longer-pin tool. The study confirms the critical role of process parameter optimisation and tool geometry in producing high-quality dissimilar FSW T-joints suitable for lightweight structural applications. Full article

Friction stir welding (FSW) of dissimilar aluminium alloys often results in non-uniform microstructure and hardness distributions due to asymmetric temperature fields and material flow. The objective of this study is to establish a quantitative relationship between thermal history, microstructural evolution, and hardness distribution in dissimilar AA5052-H32/AA6061-T6 FSW joints by combining experimental characterisation with validated thermal modelling. AA5052-H32 and AA6061-T6 plates were welded under five different parameter sets. A thermal finite element model was developed in COMSOL Multiphysics to simulate temperature evolution during welding and was validated using embedded thermocouple measurements, with predicted peak temperatures ranging from 455 °C to 641 °C. Optical microscopy, scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD) were employed to characterise grain structure and dynamic recrystallisation (DRX) behaviour, while Vickers microhardness mapping was used to evaluate the local mechanical response. The results show that DRX occurred in the nugget zone (NZ), leading to significant grain refinement, with a minimum grain diameter of 6.07 µm, representing an approximately eightfold reduction compared with the base material AA5052-H32. In contrast, the thermo-mechanically affected zone (TMAZ) experienced limited recrystallisation due to insufficient plastic deformation and temperature. The lowest hardness was observed in the TMAZ on the AA5052-H32 side, with the hardness reduction of 22% primarily caused by work hardening loss. Hardness was also reduced by 34% on the AA6061-T6 side due to decreased precipitation strengthening caused by high temperatures. This combined experimental–numerical study provides a systematic thermal–microstructure–hardness framework for understanding and predicting local property variations in dissimilar FSW joints. Full article

Shipbuilding and offshore structures employ a wide range of metallic materials, from standard and high-strength steels to non-ferrous aluminium and titanium alloys. While welding remains the dominant joining method, the reliable joining of dissimilar metals still presents significant challenges. The explosion welding (EXW) technique has been increasingly adopted over traditional methods for joining dissimilar metallic materials, due to the advantage of avoiding constraints related to metallurgical incompatibility. The EXW is a solid-state joining process in which an explosive detonation provides the energy required to drive two metal surfaces into high-velocity collision, producing a metallurgical bond. This process results in partial melting at the wavy interface and the formation of intermetallic properties, which can lead to cracking when exposed to dynamic loading. A well-established application in shipbuilding is the connection of an aluminium superstructure to steel decks. This study evaluates the mechanical behaviour of aluminium–steel explosion-welded joints for ship structures. The examined joints comprise ASTM A516 Gr55 structural steel, clad by explosion welding with AA5086 aluminium alloy using an intermediate layer of AA1050 commercially pure aluminium. Tensile tests were carried out using full-field techniques, such as digital image correlation (DIC) and infrared thermography (IRT). Full article

Aluminium alloys are known for their high strength-to-weight-ratio offering a wide range of applications in the aerospace and automotive industries. However, challenges exist like porosity, oxidation, solidification shrinkage, hot cracking, etc., in joining aluminium alloys. To address these challenges, there is a necessity to understand the process parameters for the welding/joining of aluminium alloys. The present study aims to investigate the effect of cold metal transfer (CMT) welding process parameters (i.e., welding speed and wire feed rate) on mechanical properties for dissimilar AA6061-AA6082 alloys weld joints. Two different welding conditions viz. CMT1 (speed: 0.5 m/min with feed: 5 m/min) and CMT2 (speed: 0.3 m/min with feed: 3 m/min), were considered. The weldments were deployed for testing different mechanical properties such as tensile, impact, hardness, corrosion tests and bead profile geometries. The results reveal that CMT1 has better mechanical properties (tensile_233 MPa; impact_8 J; corrosion rate_0.01368 mm/year) than CMT2, showing the welding speed and wire feed rate play a significant role in the joint performance. The heat affected zone and fusion zone are narrow for CMT1 when compared with CMT2. The present study provides insights into the CMT process and dissimilar joining of aluminium alloys that might be helpful for additive manufacturing of dissimilar aluminium alloys as future research directions. Full article

In this study, FSW experiments were conducted on a 4 mm-thick A380 aluminium alloy plate and 6061 aluminium alloy using four different needle lengths (2.5 mm, 2.8 mm, 3.0 mm, and 3.5 mm) of H13 steel. The experiments were conducted at the same welding parameters (1000 rpm and 120 mm/min) to explore the effects of different stirring needle lengths on the microstructures and properties of the FSW joints. The experimental results show that FSW joints with varying lengths of needles have a significant effect on the microstructures and properties of welded joints, and the tensile strength increases and then decreases with increases in the needle length. A 2.8 mm needle length can achieve the maximum tensile strength of 203 MPa, about 85.3% of the base material. Too long or too short a needle leads to a decrease in joint performance. Furthermore, different needle lengths have a significant influence on the flowability of the weld core zone, and a suitable needle length will lead to better flowability in the weld core zone. With increases in the needle length, the heat production also increases, and the area of the RS-HAZ will increase with the heat production. When the joints achieve appropriate heat production, the weld core zone will experience grain refinement. At the same time, the grain will grow in the RS-HAZ; the hardness cloud diagram shows that, in the RS-HAZ, the material properties are weaker, and the tensile specimens are mainly fractured in the RS-HAZ. Finally, the tensile specimens exhibit mixed fracture. Full article

This paper presents a numerical analysis of dimple spot welding (DSW) as an innovative joining technique for dissimilar materials, namely steel and aluminium alloys. Employing a finite element (FE) model, the study simulates the fatigue performance of DSW joints, considering crucial factors such as contact friction and cyclic loading conditions. While various numerical models are proposed, the simulation incorporating friction and fatigue loading appears to offer the highest accuracy. The research highlights that the fatigue behaviour of DSW joints can be effectively investigated through the non-local theory of the implicit gradient approach by utilising the fatigue curve of arc-welded structures composed of steel or aluminium alloys. Specifically, simulations incorporating friction and fatigue loading demonstrate that the steel spot weld does not represent the weakest point within the joints. Full article

This study aims to explore the effects of various pre- and post-weld heat treatments (PWHTs) on the microstructural and mechanical properties of dissimilar aluminium alloys, namely AA7075 and AA2024, joined through rotary friction welding. The joints were rigorously evaluated through multiple characterization methods, revealing no signs of cracking or incomplete bonding. This study observed that dissimilar joints between AA7075 and AA2024 alloys showed increased flash formation on the AA7075 side due to its lower melting point relative to the AA2024 alloy. Various zones within the weld region were identified, such as the dynamic recrystallized zone (DRZ), the thermo-mechanically affected zone (TMAZ)—which includes TMAZ-1 with elongated grains and TMAZ-2 with compressed or distorted grains—the heat-affected zone (HAZ), and the base metal (BM) zone. Of all the welding conditions examined, the post-weld heat-treated (PWHT) AA2024/AA7075 joint produced by rotary friction welding showed the highest strength, with a yield strength (YS) of 305 ± 2 MPa and an ultimate tensile strength (UTS) of 477 ± 3 MPa. This improvement in strength can be attributed to the significant strengthening precipitates of MgZn₂ (found on the AA7075 side), θ-Al₂Cu, and S-Al₂CuMg (found on the AA2204 side) formed during post-weld ageing. Notably, all dissimilar welds failed in the HAZ region on the AA2024 side due to coarse grain formation, identifying this as the weakest area. Full article

Collision welding is a promising approach for joining conventional materials in identical or dissimilar combinations without heat-related strength loss, thereby opening up new lightweight potential. Widespread application of this technology is still limited by an insufficient state of knowledge with respect to the underlying joining mechanisms. This paper applies collision welding to a material combination of DC04 steel and EN AW 6016 aluminium alloy. Firstly, the welding process window for the combination is determined by varying the collision speed and the collision angle, the two main influencing variables in collision welding, using a special model test rig. The process window area with the highest shear tensile strength of the welded joint is then determined using shear tensile tests and SEM images of the weld zone. The SEM investigations reveal four distinct metallographic structures in the weld zones, the area fractions of which are determined and correlated with collision angle and shear tensile strength. Full article

Dissimilar joining through solid-state welding is an important engineering tool to address the transportation industry’s sustainable goals. The dissimilar friction stir lap welding (FSLW) of two different aluminium alloys (AA5182 and AA5052 with two different thicknesses) to steels AISI1010 and DP1000 was performed in this work, in order to analyse the effect of the mismatch in base material properties and plate thickness on the joint strength and fracture location. The mechanical behaviour and the strength of the welds were assessed using transverse tensile–shear testing and hardness measurements. Strain data acquisition through Digital Image Correlation (DIC) was used. The differences in fracture location registered for the different joints are explained based on the alloy’s plastic properties and on the mismatch in thickness between the plates. Local stress–strain curves were plotted, using the strain data acquired through DIC, to highlight the mechanisms resulting in the differences in tensile behaviour among the joints. It is concluded that despite the differences in failure location and tensile behaviour, the strength of the joints was very similar, irrespective of the base material combinations. Full article

To fabricate joints of dissimilar materials such as alumnium and titanium with excellent joint properties with limited defects, there is a need to use effective joining techniques. Friction stir welding (FSW) and friction stir spot welding (FSSW) are solid-state welding techniques considered environmentally friendly joining techniques. The two techniques have been used to join numerous materials including aluminium, copper, and titanium. Joining dissimilar materials has seen a signifcant expansion worldwide due to the high demand for dissimilar joining exhibiting specific properties to be used for specific applications. This short review presents the resulting properties of joints made with aluminium and titanium using friction stir welding and friction stir spot welding. Microstructure evolution, mechanical properties, and other properties are presented and critically reviewed. Many aluminium and titanium alloys have been welded using several process parameters and tool geometries. In FSW, it has been seen that aluminium/titanium exhibited high strength when the rotational speed is well controlled. From the gathered information, it was concluded that the tool rotational speed was associated with heat input and low speed resulting in low heat input. This produced fine recrystallized grains, especially at the joint interface. On the other hand, FSSW has also been utilized to weld Al to Ti. The results showed that parameters such as rotational speed and dwell time had an impact on the formation of intermetallic compounds (IMCs) including Ti₃Al and mechanical properties were achieved. It was observed that FSSW between aluminium and titanium has not been well researched; therefore, there is a need to further study the behavior of the two materials when spot welded. It is expected that the augmentation of knowledge on the fabricated joint behavior will lead to the expansion of these techniques for specific applications and to the optimization of FSW and FSSW between alumnium and titanium alloys. Full article

This research focuses on the computational modelling and comparative analysis of friction stir welding (FSW) and stationary shoulder friction stir welding (SSFSW) applied to AA6061-T6 aluminium alloy. SSFSW, an FSW variant, employs a stationary shoulder and a rotating pin. This study introduces a numerical model for both processes, using the innovative Smoothed Particle Hydrodynamics (SPH) technique to capture their distinct thermo-mechanical characteristics. The aim is to unravel its mechanics and multi-physics in SSFSW and compare it with conventional FSW. The temperatures predicted by the model exhibited a close agreement between the advancing side (AS) and retreating side (RS). Plastic strain patterns show that regular FSW is different from SSFSW. In SSFSW, the strain is less, and the plastic area is comparatively slightly narrower. The distinct “ironing effect” resulting from the stationary shoulder in SSFSW reduces the heat-affected zone (HAZ). Yet, it maintains efficient plasticisation and material flow within the pin-affected zone (PAZ). This research emphasises the significant impact of temperature, strain, material flow, and thermo-mechanical characteristics on the quality of joints. Future suggestions include exploring process parameters more broadly, examining dissimilar welding techniques and hybrid approaches, and comprehensively investigating the diverse effects of SSFSW under various configurations and joint angles. Full article

This research study investigates the influence of sampling direction on the microstructure and mechanical properties of dissimilar joints formed by friction stir welding (FSW). The specimens were cut in two directions: perpendicular (transverse) and parallel (longitudinal) to the FSW joint. The tests conducted included X-ray diffraction (XRD), macrostructure, microstructure, tensile, microhardness, and fractography analysis. Different phases were noted in the XRD patterns and explained, with the aluminum phase being the dominating one. The results further showed that the transverse dissimilar joint exhibited higher microhardness compared to the longitudinal dissimilar joint, which is consistent with the respective grain sizes. Moreover, the ultimate tensile strength of the longitudinal joint exceeded that of the transverse joints, showing a substantial 47% increase. Similarly, the elongation of the joints followed a similar trend, with the longitudinal joint displaying a significant 41% increase in elongation compared to the transverse joint. Fractographic analysis revealed ductile fracture behaviour in all joints. Full article

The aim of this work was to investigate the challenges associated with bonding Al-Mg alloys and develop a new method for bonding these alloys to steels. During an extensive R&D project, over 80 attempts, using 11 methods, were made to bond Al-6 wt.% Mg alloy (Al-5056/Al-5A06) to two types of stainless steels (heat-resistant 1Cr18Ni9Ti and conventional 316). Wide ranges of temperature (500 °C to 580 °C), pressure (0.5 MPa to 10 MPa) and time (1 min to 2 h) were used when direct diffusion bonding of these alloys. Then, effects of using various interlayers and brazing foils were investigated. The interlayers used in this work were gallium, pure titanium, copper and aluminium foils, aluminium 6061 alloy sheets, aluminium-silicon brazing foils, zinc and zinc alloy foils as well as an active brazing foil (known as Incusil-ABA containing silver, copper, indium and titanium). Several complex and multi-stage processes, using up to 3 different interlayers in the same joint, were also developed and assessed. Examination and assessment of the bonded samples, including failed attempts, paved the way of developing new methods for bonding these dissimilar materials. A number of samples with tensile strengths from 200 MPa to 226 MPa were made by using complex combinations of 2 or 3 interlayers and triple-stage bonding cycles. The highest recorded bond strength was 226 MPa in the as-bonded condition. This value is above the measured yield strength (134 MPa) and about 93% of the measured ultimate strength (243 MPa) of the parent Al-Mg alloy after it was subjected to the same bonding cycle. Since the use of complex processes was not feasible for bonding large components, a simpler and more practical bonding cycle was also developed in the project. Using the simpler process, joints with tensile strengths around 90 MPa could be made. This article also sheds light on the difficulties associated with brazing and soldering aluminium alloys with a high magnesium content. Full article

In this work, rotary friction welding processes of dissimilar AA7075/AA5083 aluminium alloy rods with the diameter of 15 mm were performed at varying rotational speeds, typically 370 to 2500 rpm. The aim of this research is to improve mechanical properties, in particular, strength and fatigue performance of the weld joints. Several experiments including macro and microstructural examinations, Vickers microhardness measurements, tensile tests, fatigue tests and residual stress measurements were carried out. Results showed that at higher rotational speeds, typically 540 rpm or above, the dissimilar AA7075/AA5083 rotary friction weld joints revealed a static fracture in the AA5083 base metal side, indicating that the joint efficiency is more than 100%. It seemed that the best weld joint was achieved at the rotational speed of 1200 rpm, in which the friction heat was sufficient to form metallurgical bonding without causing excessive flash and burn-off. In such a condition, the fatigue strength of the weld joint was slightly higher than AA5083 base metal, but it was lower than AA7075 base metal. It was confirmed that the crack origin is observed at the interface followed by fatigue crack growth towards AA5083 side, and the growth of crack seemed to be controlled by microstructure and residual stress. Full article

In the current investigation, the influence of the tool geometry, the position of the materials in the joint, the welding speed on the temperature and torque developed, and on the quality of the welds in dissimilar and tri-dissimilar T joints were analysed. The aluminium alloys used were AA2017-T4, AA6082-T6, and AA5083-H111 and the friction stir welds were performed with identical shoulder tools, but with either a pin with simple geometry or a pin with progressive geometry. Progressive pin tools proved to be a viable alternative in the production of dissimilar and tri-dissimilar welds, as they provide a larger tool/material friction area and a larger volume of dragged material, which promotes an increase in the heat generated and a good mixing of the materials in the stir zone, although they require a higher torque. Placing a stronger material on the advancing side also results in a higher temperature in the stir zone but requires higher torque too. The combination of these factors showed that tools with a progressive pin provide sound dissimilar and tri-dissimilar welds, unlike single-pin tools. The increase in the welding speed causes the formation of defects in the stir zone, even in tri-dissimilar welds carried out with a tool with a progressive pin, which impairs the fatigue strength of the welds. Full article