Search Results (34)

Background: This study aimed to assess the impact of methacrylate-functionalized polyhedral oligomeric silsesquioxanes dispersed in nanosilica (MA/Ns-POSS) on the mechanical properties of light-curable dental resins and composites. The primary goal was to evaluate how different concentrations of MA/Ns-POSS (0.5–20 wt.%) affect the hardness, flexural strength, modulus, diametral tensile strength, polymerization shrinkage stress, and degree of conversion of these materials. Methods: A mixture of Bis-GMA, UDMA, TEGDMA, HEMA, and camphorquinone, with a tertiary amine as the photoinitiator, was used to create resin and composite samples, incorporating 45 wt.% silanized silica for the composites. Hardness (Vickers method, HV), flexural strength (FS), and flexural modulus (E_f) were assessed using three-point bending tests, while diametral tensile strength (DTS) polymerization shrinkage stresses (PSS), and degree of conversion (DC) analysis were analyzed for the composites. Results: The results showed that resins with 10 wt.% MA/Ns-POSS exhibited the highest E_f and FS values. Composite hardness peaked at 20 wt.% MA/Ns-POSS, while DTS increased up to 2.5 wt.% MA/Ns-POSS but declined at higher concentrations. PSS values decreased with increasing MA/Ns-POSS concentration, with the lowest values recorded at 15–20 wt.%. DC analysis also showed substantial improvement for 15–20 wt.% Conclusion: Incorporating MA/Ns-POSS improves the mechanical properties of both resins and composites, with 20 wt.% showing the best results. Further studies are needed to explore the influence of higher additive concentrations. Full article

The demand for polymer composite materials in the dental market is increasing every year. This rise is due to their excellent properties and ongoing technological advancements. The goal of this study was to develop new photoinitiators included in the liquid organic matrix, which is one of the main components of dental composites. Therefore, a series of compounds based on the indenoquinoxaline skeleton was synthesized, differing in the substituent. The spectroscopic properties of these compounds allowed their use as visible-light photoinitiators of radical polymerization in combination with (phenylthio)acetic acid. In addition to the polymerization kinetics, the lifetime and quantum yield of the triplet-state formation and the rate constants of its quenching by (phenylthio)acetic acid were determined. The durability of the designed composites was also assessed. Ageing tests included hydrothermal ageing, allowing for the determination of sorption, solubility, and mass change. Solutions imitating the oral cavity environment—distilled water, artificial saliva, n-heptane, and 3% acetic acid—as well as solutions containing pigments were used for these studies. Determination of the mass change and colour stability allowed for the assessment of how these materials react to long-term exposure in the oral environment. It was found that the solution simulating the natural oral environment has a significant impact on the hydrolytic stability and colour stability of the materials. Full article

Objective: The aim of this study was to evaluate the cure efficiency and biocompatibility of a novel iron-based coordination complex used as a photoinitiator in comparison to conventional ethyl (2,4,6-trimethylbenzoyl) phenylphosphinate (TPO-L) and camphorquinone (CQ) as photoinitiators in dental 3D-printed resins. Materials and Methods: Experimental dental resin formulations were prepared by blending 1:1 ratio of Bis-GMA and TEGDMA, to which 0.2 wt% of either the iron-based coordination complex or CQ were added, along with 0.2 wt% EDAB and 0.4 wt% IOD, and the TPO-L. The degree of conversion (DC) was measured using Fourier transform infrared spectroscopy (FTIR). Biocompatibility was assessed by evaluating the viability of L929 fibroblast-like cells using the MTT assay 24 h post-exposure. Statistical analyses included a two-way ANOVA followed by Tukey’s test for post hoc comparisons, with significance at p < 0.05. Results: The degree of conversion for the iron-based coordination complex (84.54% ± 1.69%) was significantly higher than that for the TPO-L (78.77% ± 1.25%) and CQ-based resins (73.21% ± 0.47%) (p < 0.001). The iron-based coordination complex and TPO-L resins exhibited significantly higher conversion than CQ-based resins (p < 0.001). Regarding biocompatibility, the cell viability test revealed that the iron-based coordination complex demonstrated the highest cell viability at 86.5% ± 10.24%, followed by TPO-L with 80.03% ± 11.07%. CQ showed the lowest cell viability of 51.29% ± 8.44% (p < 0.05). Tukey’s test confirmed significant differences between CQ and other photointiators (p < 0.05), while no significant difference was found between TPO-L and the iron-based coordination complex. Conclusions: This study introduces a novel iron-based coordination complex photoinitiator that demonstrates enhanced cure efficiency and comparable biocompatibility to TPO-L, while significantly reducing the cytotoxicity associated with CQ. Its longer absorption wavelength supports deeper layer curing, making it a promising alternative for dental 3D printing, particularly in bioactive scaffold applications requiring minimized cytotoxicity. Full article

Background/Objectives: Diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide (TPO) is widely used in the dental industry as a photoinitiator for resin-based materials, while its use may be further limited given its toxicological risks. The aim of this study was, therefore, to analyze the residual TPO content of 3D-printed resin-based dental splint materials. Methods: Six resin-based splint materials were analyzed: LuxaPrint Ortho Plus (DMG), FREEPRINT splint 2.0 (Detax), optiprint splint (Dentona), KeySplint Soft (KeyPrint), FREEPRINT ortho (Detax), V-Print splint comfort (Voco). Grid-shaped specimens were fabricated using the recommended workflow of each manufacturer (n = 18). TPO extraction was conducted using a maximum of eight extraction cycles of 72 h at a temperature of 37 °C until no more TPO eluates were detected by high-performance liquid chromatography (HPLC). The margin of safety (MoS) was calculated as the ratio between the Derived No-Effect Level (DNEL) and the estimated exposure based on the amount of TPO extracted. Results: The total amount of extracted TPO was the lowest for LuxaPrint Ortho Plus (Mean ± SD; 44.0 ± 17.1 ng/mL), followed by optiprint splint (80.6 ± 21.1 ng/mL), FREEPRINT splint 2.0 (127.4 ± 25.3 ng/mL), FREEPRINT ortho (2813.2 ± 348.0 ng/mL), V-Print splint comfort (33,424.6 ± 8357.9 ng/mL) and KeySplint Soft (42,083.5 ± 3175.2 ng/mL). For all tested materials, the calculated MoS was above the critical value of 1, demonstrating toxicological safety in the cured, clinically relevant state. Conclusions: Large differences in the residual TPO content were observed between the materials. Although the TPO content in the uncured state may exceed toxicological safety limits, appropriate curing of the investigated materials resulted in a significant reduction in TPO elution and, thus, in products with a very low toxicological risk for the patient. Full article

This project intends to develop restorative dental nanomaterial composites that are light-curable and show minimal shrinkage. Such nanocomposites are improved via employing 2,2-bis[4(2-hydroxy-3-methacryloylpropyloxy) phenyl] propane (Bis-GMA) with the unsaturated monomers bisphenol A dimethacrylate, N,N-dimethylacetamide (DMA), ethylene glycol (EG), and methacrylic acid (MAA) and loading them with SiO₂, ZrO₂, or hydroxyapatite (HA) as nanofillers of 10–30 nm. The first step was to create and characterize these novel dental materials. 1,6-hexanediol methacrylate (HDOMA) was used as a cross-linking agent. The composites based on Bis-GMA and HDOMA with a mass ratio of 40/20 were loaded with 2.5, 5.0, 7.5, 10.0, 12.5, and 15.0 wt.% of the fillers mentioned above. Photopolymerization was induced by a system of photoinitiation based on Camphorquinone/2- (Diethyl amino) ethyl acrylate (CQ/DMAEMA). The nanofillers were treated with 3-(methacryloyloxy) propyltrimethoxysilane (MPTMS) at a ratio of 1.5, 2.5, as well as 3.5%wt. compared to the filler) and a silane coupling agent to increase bonding between the phases and reduce the tendency of agglomerations. SEM images displayed the adhesion between the matrix and the three functionalized nanofillers. FTIR was used to prove the functionalization of the nanofillers by silanization with MPTMS. According to the polymer matrix, two different series of dental nanocomposites were obtained. The compressive strength of dental nanocomposites treated with 2.5 wt.% MPTMS was considerably more significant than those treated with 1.5 and 3.5%wt. MPTMS. Compressive strength (CS) and volumetric shrinkage (VS) were examined as examples of physicochemical properties. This improved nanocomposite was tested for its suitability as a dental restorative material and found to have low shrinkage and high strength. Full article

Billions of patients struggle with dental diseases every year. These mainly comprise caries and related diseases. This results in an extremely high demand for innovative, polymer composite filling materials that meet a number of dental requirements. The aim of the study was to modify the light-cured composition of permanent dental fillings by changing the composition of the liquid organic matrix. New photoinitiators (DQ1-DQ5) based on a quinoline or quinoxaline skeleton and a co-initiator-(phenylthio)acetic acid (PhTAA) were used. In addition, monomers that have been traditionally used in dental materials were replaced by trimethylolpropane triacrylate (TMPTA). The neutral dental glass IDG functioned as an inorganic filler. The influence of the storage conditions of the developed composites in solutions simulating the natural oral environment during the consumption of different meals on sorption, solubility, and mass changes was assessed. For the tests, fifty-four cylindrical composite samples were prepared according to ISO 4049 guidelines and stored in different solutions. Distilled water, artificial saliva, heptane, 10% ethanol, and 3% acetic acid, as well as solutions containing pigments such as coffee, tea, red wine, and Coca-Cola, were used for the studies. The samples were stored in these solutions for 7, 14, 28, 35, 42, 49, 56, and 63 days at 37 °C. The sorption, solubility, and mass changes in the tested samples were determined, and the trend of these changes as a function of storage time was presented. The results were analyzed considering the nature of the solution used, i.e., aqueous, hydrophobic, and acidic. The properties evaluated changed in a different way, characteristic for each of the abovementioned solution groups. It was found that the type of solution simulating the natural environment of the oral cavity has the greatest influence on the sorption, solubility, and changes in the mass of the tested material. Full article

Aim: Polyurethane-based aligners, created through photoinitiated free-radical polymerization, have been the subject of numerous studies focusing solely on their mechanical properties. In contrast, we investigate their thermomechanical properties, which are crucial for their efficacy. This paper aims to investigate the effects of different UV light exposure durations on the complex modulus of elasticity, tan delta, glass transition temperature, and the degree of conversion (DC). Methods: Aligners were printed using Tera Harz TC-85 and NextDent Ortho Flex resin with specific exposure times (2, 2.4, 3, 4, and 4.5 s for Tera Harz; 5, 6, 7, and 8 s for NextDent) and processed per manufacturer guidelines. The degree of conversion was analyzed using Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) spectroscopy, while Dynamic Mechanical Analysis (DMA) characterized the mechanical properties (complex modulus and tan delta) and the glass transition. Results: Tera Harz TC-85 showed a higher degree of conversion (90.29–94.54%), suggesting fewer residual monomers, which is potentially healthier for patients. However, its lower glass transition temperature (35.60–38.74 °C) might cause it to become rubbery in the mouth. NextDent Orto Flex, with a higher storage modulus (641.85–794.55 MPa) and Tg (49.36–50.98 °C), offers greater rigidity and stability at higher temperatures (greater than temperature in the oral cavity), ideal for orthodontic forces, though its lower degree of conversion raises health concerns. Conclusions: Tera Harz TC 85 generally achieves higher DC and more stable polymerization across different UV exposure times than NextDent Orto Flex. Optimal polymerization times significantly impact both the mechanical and thermal properties of these dental resins, with NextDent showing optimal properties at 7 s and Tera Harz benefiting from both very short and extended exposure times. Full article

Photopolymerization is becoming increasingly popular in industry due to its copious advantages. The vital factor in the entire pre-polymerization formulation is the presence of photoinitiators. Depending on the application, photoinitiators have different features. Hence, scientists are particularly interested in developing new photoinitiators that can expand the scope of applications and be used to create products with the features demanded by current trends. This brief review summarizes the photoinitiators used in dental materials and hydrogels and those obtained from natural and synthetic sources. Full article

Color stability is crucial for dental materials to ensure they perfectly match a patient’s tooth color. This is particularly challenging in photoresist-based additive manufacturing. Although some studies have addressed this issue, the exact causes of discoloration and ways to minimize it remain unclear. In this study, the intrinsic causes of discoloration in materials intended for 3D printing are investigated by examining thin-film samples (1200 µm) of various compositions, which are stored under different conditions. The samples are evaluated by measuring the UV-Vis absorption spectra at regular intervals to monitor changes. The findings reveal that both the composition of the formulations and the storage conditions significantly influence the discoloration behavior. Furthermore, methods have been developed to reduce or completely prevent discoloration. The use of photoinitiators with sterically demanding benzoyl moieties, as well as the addition of stabilizers, effectively decreases the intensity of emerging discoloration. Furthermore, incorporating the oxidizing agent cumene hydroperoxide (CHP) results in materials that maintain color stability. Full article

In this work, photoinitiation systems based on dibenzo[a,c]phenazine sensitivity to visible light were designed for their potential application in dentistry. Modification of the structure of dibenzo[a,c]phenazine consisted of introducing electron-donating and electron-withdrawing substituents and heavy atoms into position 11. The synthesized compounds are able to absorb radiation emitted by dental lamps during photoinitiation of the polymerization process. In the presence of acrylates, dibenzo[a,c]phenazines show excellent photoinitiating abilities in systems containing an electron donor or a hydrogen-atom donor as a second component. The developed systems initiate the polymerization process comparable to a commercial photoinitiator, i.e., camphorquinone. Moreover, the performed studies showed a significant shortening of the polymerization time and a reduction in the amount of light absorber. This indicates that polymeric materials are obtained at a similar rate despite a significant reduction in the concentration of the newly developed two-component photoinitiating systems. Full article

Dyes based on quinoline and quinoxaline skeletons were designed for application as visible light photoinitiators. The obtained compounds absorb electromagnetic radiation on the border between ultraviolet and visible light, which allows the use of dental lamps as light sources during the initiation of the photopolymerization reaction. Their another desirable feature is the ability to create a long-lived excited state, which enables the chain reaction to proceed through the mechanism of intermolecular electron transfer. In two-component photoinitiating systems, in the presence of an electron donor or a hydrogen atom donor, the synthesized compounds show excellent abilities to photoinitiate the polymerization of acrylates. In control tests, the efficiency of photopolymerization using modified quinoline and quinoxaline derivatives is comparable to that obtained using a typical, commercial photoinitiator for dentistry, camphorquinone. Moreover, the use of the tested compounds requires a small amount of photoinitiator (only 0.04% by weight) to initiate the reaction. The research also showed a significant acceleration of the photopolymerization process and shortening of the reaction time. In practice, this means that the new two-component initiating systems can be used in much lower concentrations without slowing down the speed of obtaining polymer materials. It is worth emphasizing that these two features of the new initiating system allow for cost reduction by reducing financial outlays on both materials (photoinitiators) and electricity. Full article

A low ratio of polymerization is a major problem in resin-based composites. In this paper, the plasmonic effect of gold-covered silica nanoparticles on the physicochemical and mechanical properties of bisphenol A diglycidyl dimethacrylate (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) green light-photopolymerizable dental resin was investigated at an intensity of 1.4 mW/cm² for 40 s. Transmission electron microscopy (TEM) showed silica of about 350 nm covered with 12–15 nm gold nanoparticles (Au NPs) at 100% nominal coverage. Five different concentrations of bare and patchy silica particles were used; in the latter composite, the calculated Au wt% were 0.0052 wt%, 0.0104 wt%, 0.0208 wt%, 0.04160 wt%, and 0.0823 wt%. The plasmon peak of patchy silica-filled nanocomposite overlapped with the absorption of Irgacure 784 photoinitiator and green LED light emission peak. The effect of plasmon-enhanced polymerization achieved with green light illumination was analyzed using diametral tensile strength (DTS), differential scanning calorimetry (DSC), surface plasmon resonance imaging (SPRi), and degree of conversion (DC) based on Raman spectroscopy. The values of the Au NP with 0.0208 wt% was found to be maximum in all the measured data. Based on our result, it can be concluded that the application of patchy silica particles in dental resin can improve the polymerization ratio and the mechanical parameters of the composite. Full article

There is a dearth of adhesive systems capable of forming stable bonds between restorative materials and tooth surfaces. To address the concern, this study determined the effects of using methacrylate-functionalized boron nitride nanosheets (BNNSs) in a polymeric dental adhesive system. The bisphenol A glycidyl dimethacrylate (BisGMA):2 hydroxyethyl methacrylate (HEMA) (60:40) adhesive monomer blend with a photoinitiator was filled with 0 wt% (control), 0.1 wt%, and 1 wt% BNNSs and light cured. Fourier transform infrared spectroscopy was performed to determine the conversion degree of monomer double bonds (DoC). Water absorption and solubility were measured. Flexural strength and Youngs’s modulus were evaluated to determine the mechanical properties of the composite adhesive system. Finally, dentin bond strength degradation and fracture mode were quantified with a microtensile bond test to confirm the bonding ability of the developed adhesive system. Results showed that the incorporation of BNNSs increased DoC (9.8% and 5.4% for 0.1 and 1 wt%, respectively), but it did not affect water sorption (101.9–119.72 (µg/mm³)), solubility (2.62–5.54 (µg/mm³)), Young’s modulus (529.1–1716.1 MPa), or microtensile bond strength (46.66–54.72 MPa). Further studies are needed with varying BNNS loading percentages from 0.1 wt% to 1 wt% in order to more comprehensively determine the effect of BNNSs on dental adhesives. Full article

The goal of this study was to compare the mechanical properties of experimental resin dental composites containing a conventional photoinitiating system (camphorquinone CQ and 2-(dimethylami-no)ethyl methacrylate (DMAEMA)) to a photoinitiator system containing 1-phenyl-1,2 propanedione (PPD) with 2-(dimethylami-no)ethyl methacrylate) or acting alone phenylbis(2,4,6-trimethylbenzoyl)-phosphine oxide (BAPO). The manually produced composites consisted of an organic matrix: bis-GMA (60 wt. %), TEGDMA (40 wt. %), and silanized silica filler (45 wt. %). The composites contained 0.4/0.8 wt. %, 0.8/1.6 wt. %, and 1/2 wt. % of PPD/DMAEMA and another group included 0.25, 0.5, or 1 wt. % of BAPO. Vickers hardness, microhardness (in the nanoindentation test), diametral tensile strength, and flexural strength were assessed, and CIE L* a* b* colorimetric analysis was conducted for each composite produced. The highest average Vickers hardness values were obtained for the composite containing 1 wt. % BAPO (43.73 ± 3.52 HV). There was no statistical difference in the results of diametral tensile strength for the experimental composites tested. The results of 3-point bending tests were the highest for composites containing CQ (77.3 ± 8.84 MPa). Despite the higher hardness of experimental composites including PPD or BAPO, compared with composites with CQ, the overall results indicate that the composite with CQ still represents a better solution when used as a photoinitiator system. Moreover, the composites containing PPD and DMAEMA are not promising in terms of color or mechanical properties, especially as they require significantly longer irradiation times. Full article

Modern dentistry places great demands on the dental composites used for filling tooth cavities or treating cavitated tooth decay. The aim of the work was to modify the properties of composites by changing the initiators and co-initiators. This was achieved by using initiators based on a quinoxaline skeleton and co-initiators that are derivatives of acetic acid, which is an advantage of these photoinitiating systems due to the elimination of aromatic amines from the photocurable composition. The composites also differed in dental fillers. The effect of the compounds on the exothermicity of the photopolymerization process, the surface morphology of the obtained materials and the maximum compressive strength were determined. The photoinitiating capacity of the two-component systems was tested by the microcalorimetric method using the multifunctional monomer TMPTA, typical for dental filler compositions. The new photoinitiating systems show particularly good efficiency of free radical polymerization initiation, which occurs by the photoinduced intermolecular electron transfer (PET) mechanism. The comparison of the tested systems with camphorquinone, a photoinitiator traditionally used in dentistry, made it possible to observe a decrease in temperature during photopolymerization without a significant decrease in the polymerization rate or increase in photocuring time, as well as a better homogeneity of the surface of the obtained polymeric materials. This indicates that dye–acetic acid derivative systems may be useful in dental applications. Full article