Search Results (24)

Mediterranean landscapes are shaped by natural disturbances such as herbivory and fire that regulate vegetation structure and fuel loads. As a result of the cessation of traditional agricultural practices, land abandonment is a widespread phenomenon in these landscapes, leading to shrub encroachment and heightened fire hazard. This study reports the effects of grazing by domestic herbivores on vegetation structure in transitional woodland–shrubland systems across three case study areas in Portugal. The effects of low and moderate grazing intensity by cattle and horses on vegetation structure were assessed on three vegetation strata—canopy, shrubs, and grasses—using indicators to evaluate the influence of grazing on both horizontal and vertical vegetation structure. Moderate grazing shaped vertical vegetation structure by reducing shrub and grass height and by browsing and thinning the lower branches, creating a discontinuity between understorey and canopy layers. These effects on vertical fuel continuity are anticipated to limit the upward spread of flames and reduce the potential for crown fires. In contrast, low-intensity grazing showed limited effects on both vertical and horizontal vegetation structure. This work highlights the potential of using domestic herbivores as a tool to manage vegetation structure and its contribution to mitigating local wildfire hazards. Full article

Prescribed burning is a cost-effective method for reducing hazardous fuels in pine- and oak-dominated forests, but smoke emissions contribute to atmospheric pollutant loads, and the potential exists for exceeding federal air quality standards designed to protect human health. Fire behavior during prescribed burns influences above-canopy sensible heat flux and turbulent kinetic energy (TKE) in buoyant plumes, affecting the lofting and dispersion of smoke. A more comprehensive understanding of how enhanced energy fluxes and turbulence are related during the passage of flame fronts could improve efforts to mitigate the impacts of smoke emissions. Pre- and post-fire fuel loading measurements taken during 48 operational prescribed burns were used to estimate the combustion completeness factors (CC) and emissions of fine particulates (PM_2.5), carbon dioxide (CO₂), and carbon monoxide (CO) in pine- and oak-dominated stands in the Pinelands National Reserve of southern New Jersey. During 11 of the prescribed burns, sensible heat flux and turbulence statistics were measured by tower networks above the forest canopy. Fire behavior when fire fronts passed the towers ranged from low-intensity backing fires to high-intensity head fires with some crown torching. Consumption of forest-floor and understory vegetation was a near-linear function of pre-burn loading, and combustion of fine litter on the forest floor was the predominant source of emissions, even during head fires with some crowning activity. Tower measurements indicated that above-canopy sensible heat flux and TKE calculated at 1 min intervals during the passage of fire fronts were strongly influenced by fire behavior. Low-intensity backing fires, regardless of forest type, had weaker enhancement of above-canopy air temperature, vertical and horizontal wind velocities, sensible heat fluxes, and TKE compared to higher-intensity head and flanking fires. Sensible heat flux and TKE in buoyant plumes were unrelated during low-intensity burns but more tightly coupled during higher-intensity burns. The weak coupling during low-intensity backing fires resulted in reduced rates of smoke transport and dispersion, and likely in more prolonged periods of elevated surface concentrations. This research facilitates more accurate estimates of PM_2.5, CO, and CO₂ emissions from prescribed burns in the Pinelands, and it provides a better understanding of the relationships among fire behavior, sensible heat fluxes and turbulence, and smoke dispersion in pine- and oak-dominated forests. Full article

Carbon stocks provide information that is essential for analyzing the role of forests in global climate mitigation, yet they are highly vulnerable to wildfires in Mediterranean ecosystems. These carbon stocks’ exposure to fire is usually estimated from specific allometric equations relating tree height and diameter to the overall amount of aboveground carbon storage. Assessments of vulnerability to fire additionally allow for specific fire resistance (bark thickness, crown basal height) and post-fire recovery traits (cone mass for regeneration, and fine branches or leaves mass for flammability) to be accounted for. These traits are usually considered as static, and their temporal dynamic is rarely assessed, thus preventing a full assessment of carbon stocks’ vulnerability and subsequent cascading effects. This study aimed to measure the pools of carbon stocks of individual trees varying between 30 and 96 years old in the Djbel Mansour Aleppo pine (Pinus halepensis) forest in semi-arid central Tunisia in the southern range of its distribution to fit a sigmoid equation of the carbon pools and traits recovery according to age as a vulnerability framework. Allometric equations were then developed to establish the relationships between fire vulnerability traits and dendrometric independent variables (diameter at breast height, height, and live crown length) for further use in regional vulnerability assessments. The total carbon stocks in trees varied from 29.05 Mg C ha⁻¹ to 92.47 Mg C ha⁻¹. The soil organic carbon stock (SOC) at a maximum soil depth of 0–40 cm varied from 31.67 Mg C ha⁻¹ to 115.67 Mg C ha⁻¹ at a soil depth of 0–70 cm. We could identify an increasing resistance related to increasing bark thickness and basal crown height with age, and enhanced regeneration capacity after 25 years of age with increasing cone biomass, converging toward increasing vulnerability and potential cascading effects under shorter interval fires. These results should be considered for rigorous forest carbon sequestration assessment under increasing fire hazards due to climate and social changes in the region. Full article

Wildfire hazard is a prominent issue in subtropical forests as climate change and extreme drought events increase in frequency. Stand-level fuel load and forest structure are determinants of forest fire occurrence and spread. However, current fuel management often lacks detailed vertical fuel distribution, limiting accurate fire risk assessment and effective fuel policy implementation. In this study, backpack laser scanning (BLS) is used to estimate several 3D structural parameters, including canopy height, crown base height, canopy volume, stand density, vegetation area index (VAI), and vegetation coverage, to characterize the fuel structure characteristics and vertical density distribution variation in different stands of subtropical forests in China. Through standard measurement using BLS point cloud data, we found that canopy height, crown base height, stand density, and VAI in the lower and middle-height strata differed significantly among stand types. Compared to vegetation coverage, the LiDAR-derived VAI can better show significant stratified changes in fuel density in the vertical direction among stand types. Among stand types, conifer-broadleaf mixed forest and C. lanceolata had a higher VAI in surface strata than other stand types, while P. massoniana and conifer-broadleaf mixed forests were particularly unique in having a higher VAI in the lower and middle-height strata, corresponding to the higher surface fuel and ladder fuel in the stand, respectively. To provide more informative support for forest fuel management, BLS LiDAR data combined with other remote sensing data were advocated to facilitate the visualization of fuel density distribution and the development of fire risk assessment. Full article

A deeper understanding of the influence of fine-scale fuel patterns on fire behavior is essential to the design of forest treatments that aim to reduce fire hazard, enhance structural complexity, and increase ecosystem function and resilience. Of particular relevance is the impact of horizontal and vertical forest structure on potential tree torching and large-tree mortality. It may be the case that fire behavior in spatially complex stands differs from predictions based on stand-level descriptors of the fuel distribution and structure. In this work, we used a spatially explicit fire behavior model to evaluate how the vertical and horizontal distribution of fuels influences the potential for fire to travel from the surface into overstory tree crowns. Our results support the understanding that crown fuels (e.g., needles and small-diameter branchwood) close to the surface can aid in this transition; however, we add important nuance by showing the interactive effect of overstory horizontal fuel connectivity. The influence of fuels low in the canopy space was overridden by the effect of horizontal connectivity at surface fire-line intensities greater than 1415 kW/m. For example, tree groups with vertically continuous fuels and limited horizontal connectivity sustained less large-tree consumption than tree groups with a significant vertical gap between the surface and canopy but high-canopy horizontal connectivity. This effect was likely the result of reduced net vertical heat transfer as well as decreased horizontal heat transfer, or crown-to-crown spread, in the upper canopy. These results suggest that the crown fire hazard represented by vertically complex tree groups is strongly mediated by the density, or horizontal connectivity, of the tree crowns within the group, and therefore, managers may be able to mitigate some of the torching hazard associated with vertically heterogenous tree groups. Full article

The hazardousness of Mediterranean landscapes has increased since the second half of the 20th century, and fuel loads of highly flammable vegetation types have increased throughout the region. Moreover, under the context of more severe fire weather, large fires of high intensity may cause losses in ecosystem services. Accordingly, fire prevention tools to monitor when and where a fire will have the most negative effects through increases in fire severity are required. Fuel characterization is key to wildfire prevention as fuel is one of the primary factors affecting wildfire risk and behavior. Here, we characterized the valuable natural vegetation in Cabañeros National Park (Central Spain) (part of the Natura-2000 network), composed of typical Mediterranean ecosystems, by using LiDAR and other auxiliary data. LiDAR data were obtained from the first Spanish National LiDAR flight, carried out over the study area in 2009–2010. LiDAR data were pre-processed and ground returns were classified using the progressive TIN filter algorithm, carrying out a sensitivity analysis using different settings. Later, the height of the points above the ground were normalized and the Canopy Height Model (CHM) was calculated. Fuel models were derived using the Prometheus fuel classification framework, and they were determined using several LiDAR height metrics and some compositional metrics (i.e., percentage covered by different height ranges) [<0.6 m, 0.6–1 m, 1–2 m, 2–4 m and ≥4 m] at 30 m. All these metrics allowed for the estimation of fractional canopy cover, fuel height, and vertical continuity. Moreover, tree-tops and crowns were delimited and standard height metrics, as well as vertical profiles, were obtained. All these data, combined with information about the flammability of dominant species and the vulnerability to fire based on functional traits, allowed for the identification of which resource values were most severely exposed to wildfires. Full article

The mild climate and, in recent decades, the increased demand for timber have favoured the establishment of extensive plantations of fast-growing species such as Pinus radiata in Galicia (a fire-prone region in northwestern Spain). This species is characterised by very poor self-pruning; unmanaged pine stands have a worrying vertical continuity of fuels after crown closure because the dead lower branches accumulate large amounts of fine dead biomass including twigs and suspended needles. Despite the important contribution of these dead ladder fuels to the overall canopy biomass and to crown-fire hazards, equations for estimating these fuels have not yet been developed. In this study, two systems of equations for estimating dead ladder fuel according to size class and the vertical distribution in the first 6 m of the crown were fitted: a tree-level system based on individual tree and stand variables and a stand-level system based only on stand variables. The goodness-of-fit statistics for both model systems indicated that the estimates were robust and accurate. At the tree level, fuel biomass models explained between 35% and 59% of the observed variability, whereas cumulative fuel biomass models explained between 62% and 81% of the observed variability. On the other hand, at the stand level, fuel-load models explained between 88% and 98% of the observed variability, whereas cumulative fuel-load models explained more than 98% of the total observed variability. These systems will therefore allow managers to adequately quantify the dead ladder fuels in pure Pinus radiata stands and to identify the treatments required to reduce crown-fire hazard. Full article

Climate change causes more extreme droughts and heat waves in Central Europe, affecting vegetative fuels and altering the local fire regime. Wildfire is projected to expand into the temperate zone, a region traditionally not concerned by fire. To mitigate this new threat, local forest management will require spatial fire hazard information. We present a holistic and comprehensible workflow for quantifying fuels and wildfire hazard through fire spread simulations. Surface and canopy fuels characteristics were sampled in a small managed temperate forest in Northern Germany. Custom fuel models were created for each dominant species (Pinus sylvestris, Fagus sylvatica, and Quercus rubra). Canopy cover, canopy height, and crown base height were directly derived from airborne LiDAR point clouds. Surface fuel types and crown bulk density (CBD) were predicted using random forest and ridge regression, respectively. Modeling was supported by 119 predictors extracted from LiDAR, Sentinel-1, and Sentinel-2 data. We simulated fire spread from random ignitions, considering eight environmental scenarios to calculate fire behavior and hazard. Fuel type classification scored an overall accuracy of 0.971 (Kappa = 0.967), whereas CBD regression performed notably weaker (RMSE = 0.069; R² = 0.73). Higher fire hazard was identified for strong winds, low fuel moisture, and on slopes. Fires burned fastest and most frequently on slopes in large homogeneous pine stands. These should be the focus of preventive management actions. Full article

Landslide trails are important elements of landslide inventory maps, providing valuable information for landslide risk and hazard assessment. Compared with traditional manual mapping, skeletonization methods offer a more cost-efficient way to map landslide trails, by automatically generating centerlines from landslide polygons. However, a challenge to existing skeletonization methods is that expert knowledge and manual intervention are required to obtain a branchless skeleton, which limits the applicability of these methods. To address this problem, a new workflow for landslide trail extraction (LTE) is proposed in this study. To avoid generating redundant branches and to improve the degree of automation, two endpoints, i.e., the crown point and the toe point, of the trail were determined first, with reference to the digital elevation model. Thus, a fire extinguishing model (FEM) is proposed to generate skeletons without redundant branches. Finally, the effectiveness of the proposed method is verified, by extracting landslide trails from landslide polygons of various shapes and sizes, in two study areas. Experimental results show that, compared with the traditional grassfire model-based skeletonization method, the proposed FEM is capable of obtaining landslide trails without spurious branches. More importantly, compared with the baseline method in our previous work, the proposed LTE workflow can avoid problems including incompleteness, low centrality, and direction errors. This method requires no parameter tuning and yields excellent performance, and is thus highly valuable for practical landslide mapping. Full article

Prescribed fire is a globally relevant fuel treatment for surface fuel management and wildfire hazard reduction. However, Mediterranean ecosystems are adapted to low and moderate fires; hence, the useful life of prescribed fires is limited. Useful life is defined as the effective rotation length of prescribed fires to mitigate fire spread based on critical surface intensity for crown combustion. In this sense, the useful life of a prescribed fire focuses on surface fuel dynamics and its potential fire behavior. In Pinus pinaster stands, the useful life can be established between 0 and 4 years. Canopy base height, time elapsed from the burning, postfire precipitation, and fine fuel moisture content during the burning were identified as the most important variables in postburn fuel dynamics. Other stand characteristics and postfire precipitation can improve the fine fuel and live fuel dynamics models. Our findings support prescribed fires as an effective fuel treatment in the medium term for forest fire prevention, according to stand characteristics and burning implementation conditions. In this sense, forest managers can use the proposed decision tree to identify the useful life of each prescribed fire based on fine fuel moisture content during burning implementation. Full article

Increasing fire size and severity over the last few decades requires new techniques to accurately assess canopy fuel conditions and change over larger areas. This article presents an analysis on vegetation changes by mapping fuel types (FT) based on conditional rules according to the Prometheus classification system, which typifies the vertical profile of vegetation cover for fuel management and ecological purposes. Using multi-temporal LiDAR from the open-access Spanish national surveying program, we selected a 400 ha area of interest, which was surveyed in 2010 and 2016 with scan densities of 0.5 and 2 pulses·m⁻², respectively. FTs were determined from the distribution of LiDAR heights over an area, using grids with a cell size of 20 × 20 m. To validate the classification method, we used a stratified random sampling without replacement of 15 cells per FT and made an independent visual assessment of FT. The overall accuracy obtained was 81.26% with a Kappa coefficient of 0.73. In addition, the relationships among different stand structures and ecological factors such as topographic aspect and forest vegetation cover types were analyzed. Our classification algorithm revealed that stands lacking understory vegetation usually appeared in shady slopes, which were mainly covered by beech stands, whereas sunny areas were preferentially covered by oak stands, where the understory reached greater height thanks to more light availability. Our analysis on FT changes during that 6 year time span revealed potentially hazardous transitions from cleared forests towards a vertical continuum of canopy fuels, where wildfire events would potentially reach tree crowns, especially in oak forests and southern slopes with higher sun exposure for lower fuel moistures and increased flammability. Accurate methods to characterize forest canopy fuels and change over time can help direct forest management activities to priority areas with greater fire hazard. Multi-date canopy fuel information indicated that while some forest types experienced a growth of the shrub layer, others presented an understory decrease. On the other hand, loss of understory was more frequently detected in beech stands; thus, those forests place lower risk of wildfire spread. Our approach was developed using low-density and publicly available datasets and was based on direct canopy fuel measurements from multi-return LiDAR data that can be accurately translated and mapped according to standard fuel type categories that are familiar to land managers. Full article

Flooded forests are very important ecosystems that are rich in terms of their diverse flora and fauna. However, they are mostly degraded in many parts of the world, and the remaining fragmented areas are in a critical condition. Forest fires are one of the major environmental disasters that cause serious damage to forest ecosystems, and negatively affect the sustainability of forest resources. In order to minimize the potential effects of fires on forest ecosystems, forest fire risk maps should be generated, and thereby the necessary precautionary measures can be taken in these areas, according to fire risk levels. Geographical information system (GIS) techniques, integrated with multi-criteria decision analysis (MCDA) methods, can be effectively used to develop risk maps for natural hazards, such as forest fires, winter storms, floods, etc. In this study, GIS techniques integrated with an AHP (analytic hierarchy process) method were used to generate a forest fire risk map. The study was implemented in the Karacabey flooded forest, located in the city of Bursa in Turkey. In the solution process, the forest fire risk was evaluated considering two major risk factors, including stand structures (tree species, crown closure, and tree stage) and topographic factors (slope and aspect). The vegetation factor under climate control was considered, instead of directly using data of climatic elements such as temperature and humidity. The results indicated that 25.28% of the forest area was of high fire risk, while 53.17% and 21.55% was of medium and low fire risk, respectively. It was found that the most effective criterion was tree species, followed by tree stage. This aspect had the least effective criterion on forest fire risk. It was revealed that GIS techniques integrated with MCDA methods can be used effectively to estimate forest fire risk zones. Full article

Quaking aspen is found in western forests of the United States and is currently at risk of loss due to conifer competition at within-stand scales. Wildfires in these forests are impactful owing to conifer infilling during prolonged fire suppression post-Euro-American settlement. Here, restoration cuttings seek to impact wildfire behavior and aspen growing conditions. In this study, we explored how actual and hypothetical cuttings with a range of conifer removal intensity altered surface fuel and overstory structure at stand and fine scales. We then simulated wildfires, examining fire behavior and effects on post-fire forest structures around aspen trees. We found that conifer removal constrained by lower upper diameter limits (<56 cm) had marginal effects on surface fuel and overstory structure, likely failing to enhance resource conditions sufficiently to sustain aspen. Increasing the diameter limit also led to a higher likelihood of fire spread and a higher rate of spread, owing to greater within-canopy wind speed, though crown fire activity decreased. Our simulations suggest heavier treatments could facilitate reintroduction of fire while also dampening the effects of wildfires on forest structure. Cutting specifications that relax diameter limits and remove a substantial portion of conifer overstory could better promote aspen restoration and mitigate fire hazard. Full article

Research Highlights: This study provides much needed insight into the development of resistance to disturbance and growth dynamics of overstory trees in response to restoration-based fuel reduction, and will be useful to scientists and managers attempting to better grasp the relative merits of restoration treatment types. Background and Objectives: Restoration-based fuel reduction treatments are common in dry, fire-prone forests of the western United States. The primary objective of such treatments is to immediately reduce a stand’s crown fire hazard. However, the impact of these treatments on residual trees is relevant to assess their longevity and resistance to future disturbances. In this study, we evaluate the effects of restoration on retained overstory ponderosa pine (Pinus ponderosa Lawson & C. Lawson) and Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) trees in western Montana, where treatments were experimentally implemented 13 years prior as part of the national Fire and Fire Surrogate study. Materials and Methods: We examined tree attributes in response to the following replicated treatments: thin-only, burn-only, thin + burn, and a no-action control. We analyzed three different tree attributes that confer resistance to common disturbances: height-to-diameter ratio (resistance to wind), bark thickness (resistance to surface fire), and growth efficiency (resistance to bark beetles). Results: Our models suggest that thinning (with or without burning) alters tree attributes relative to the control in a manner that may increase tree resistance to wind and snow breakage, surface fire, and biotic agents such as bark beetles. Further analysis of annual growth of ponderosa pine and Douglas-fir varied by treatment type: thinning-based restoration (thin-only and thin + burn) increased diameter growth for both species, crown length and width in ponderosa pine, and crown length in Douglas-fir relative to unthinned treatments. Burning (burn-only and thin + burn) did not significantly affect tree growth relative to unburned treatments. Conclusions: While low-severity prescribed burning treatments are often used for restoration and have various ecosystem benefits, this study demonstrates that thinning (alone or in addition to burning) produces more measureable, beneficial results to overstory tree disturbance resistance metrics and growth. Full article

Exclusion of natural surface fires in warm/dry mixed-conifer forests of the western U.S. has increased potential for stand-replacing crown fires and reduced resilience of these systems to other disturbances, such as drought and insect attack. Tree thinning and the application of prescribed fire are commonly used to restore more resilient ecological conditions, but currently, there is a lack of long-term data with which to evaluate restoration treatment effectiveness in forest types where resprouting shrubs dominate understory communities. At a mixed-conifer site in southwestern Colorado, we compared forest structure and understory vegetation responses to three restoration treatments (thin/burn, burn, and control) over 10 years in a completely randomized and replicated experiment. Forest density, canopy cover, and crown fuel loads were consistently lower, and crown base height was higher, in thin/burn than burn or controls, but the effects diminished over time. Ten years following treatment, >99% of all plant species within both treatments and the control were native in origin. There were no differences between treatments in understory richness, diversity, cover, or surface fuels, but graminoid cover more than doubled in all treatments over the 15-year monitoring period. Similarly, there was more than a 250% increase post-treatment in shrub density, with the greatest increases in the thin/burn treatment. In addition, we saw an increase in the average shrub height for both treatments and the control, with shrub stems >80 cm becoming the dominant size class in the thin/burn treatment. Conifer seedling density was significantly lower in thin/burn compared with burn and control treatments after 10 years. Taken together, these conditions create challenges for managers aiming to reestablish natural fire patterns and sustain mixed-conifer forests. To limit the dominance of resprouting shrubs and facilitate conifer regeneration after overstory thinning and prescribed fire, managers may need to consider new or more intensive approaches to forest restoration, particularly given current and projected climate change. Full article