Search Results (3,395)

The electrodeposition of rare earth metal alloys has attracted considerable interest, not only due to the challenges associated with the reduction in metal ions, but also because of their unique material properties and promising technological applications. This review presents a comprehensive analysis of the state-of-the-art in the electrochemical deposition of these alloys, focusing on various electrolytic systems, including aqueous solutions, organic molecular solvents, ionic liquids, and deep eutectic solvents. Despite inherent problematic factors such as low reduction potentials, competing hydrogen evolution reactions, and difficulties in controlling metal formation, recent advancements have enabled improved control over film formation, typically through the induced codeposition of lanthanides with iron-group metals. The influence of key factors, such as electrolyte composition and current/potential modes, on alloy codeposition, elemental and phase composition, structure, and deposition efficiency is discussed. The magnetic properties, electrocatalytic behavior, and corrosion resistance of the deposited films are also shown, highlighting their relevance for high-performance applications. Full article

Extended-solvent steam-assisted gravity drainage (ES-SAGD) has emerged as a promising advancement over conventional SAGD for improving the efficiency and sustainability of in situ heavy oil and bitumen recovery. By co-injecting light hydrocarbon or alternative solvents with steam, ES-SAGD integrates thermal and compositional mechanisms to reduce viscosity, accelerate chamber development, and reduce steam–oil ratios. This review synthesizes the current state of knowledge on ES-SAGD, encompassing fundamental transport mechanisms, solvent selection and phase behavior, mass transfer dynamics, laboratory and physical modeling studies, numerical simulation approaches, and field-scale operational experiences. Experimental evidence consistently demonstrates substantial mobility enhancement through solvent-induced dilution, while compositional thermal simulations highlight an improved sweep efficiency and reduced energy intensity relative to steam-only processes. Field pilots further validate accelerated early-time production and significant steam savings, though challenges related to solvent retention, asphaltene stability, and reservoir heterogeneity persist. Key research gaps are identified in solvent transport prediction, formation damage risk, long-term solvent recovery, and integrated economic–environmental optimization. Overall, ES-SAGD offers a viable pathway toward lower-emission, higher-efficiency bitumen production, provided that solvent chemistry, reservoir complexity, and operational controls are carefully managed through continued research and targeted field deployment. Full article

Hazardous compounds from used batteries pose a great threat to the environment. To prevent pollution and to recover critical materials from battery waste, efficient recycling is required. Until now, battery recycling has focused on the recovery of valuable metals from cathode materials, while organic fractions have often been neglected due to their low material value. New approaches to battery recycling are therefore necessary, where recycling methods based on supercritical carbon dioxide (SC-CO₂) extraction show great potential. In this work, a SC-CO₂ method was implemented to extract electrolyte solvents for the purification and recovery of a separator waste material (SWM) sorted out from lithium-ion battery (LIB)-based black mass. In addition, two other separation routes (ultrasonic washing and thermal treatment) were used for comparison. Based on the results from the three routes, mass balances revealed the gravimetric composition of the SWM, which includes separator, electrolyte, and electrode powder. The composition of electrolyte solvents was determined via Gas Chromatography-Mass Spectroscopy analysis. Furthermore, the polymeric separator was analyzed using Fourier Transform Infrared Spectroscopy, Thermogravimetric Analysis, and Differential Scanning Calorimetry analysis to evaluate the effects of SC-CO₂ extraction on the physicochemical properties. The recovery of electrolyte by the SC-CO₂ route is more efficient than the others, with extraction yields of 162 mg of electrolyte per gram of SWM. Moreover, no changes are observed in the analyzed properties of the polymeric separator material due to the SC-CO₂ extraction. Thus, the SC-CO₂ process proves to be a promising method for an efficient and sustainable recycling of electrolyte solvent and purifying of separator material from LIB waste. Full article

The solubility values of polyphenolic compounds in different extraction solvents are crucial for their recovery from natural matrices. Hansen solubility parameters (HSPs) stand out as a predictive tool for evaluating solute-solvent affinity and thus rational solvent selection for extraction processes. In this study, HSPs of trans-resveratrol and hesperetin were calculated using a semi-empirical method to assess the capability to predict the solubility behavior of both polyphenols in organic binary solvent mixtures. Experimental solubility of both polyphenols was determined in up to 21 monosolvents at 298.15 K and 0.1 MPa and used to classify them to iteratively calculate HSPs. Calculated HSPs were compared and discussed with literature values in terms of molecular interactions, demonstrating a fair agreement. Solubility of trans-resveratrol and hesperetin was then determined in methanol + MEK, ethanol + MEK, methanol + MiBK, ethanol + MiBK, and methanol + ethanol binary solvent mixtures. trans-Resveratrol achieved higher mole fraction solubility than hesperetin in all binary mixtures across the whole molar fraction range except in methanol + MiBK. Both compounds exhibited enhanced solubility in all alcohols + ketone binary mixtures, attributed to synergistic solvent effects. HSP analysis revealed a minimum Hansen distance between solute and solvent mixtures at compositions corresponding to the solubility maximum in synergistic systems. Additionally, calculated HSPs proved to effectively estimate the concentration at which this phenomenon occurs in all tested systems, reaching a robust correlation between maximum solubility and minimum Hansen distance. Overall, insights from this study underscore the effectiveness of experimentally derived HSPs in predicting the solubility behavior of polyphenols and seek to provide valuable guidance on solvent selection strategies for the recovery of bioactive compounds. Full article

Background/Objectives: The valorization of bioactive compounds from food industry by-products aligns with sustainable development goals and represents a strategy for obtaining functional ingredients. Hazelnut (Corylus avellana L.) skins are a phenolic-rich residue with high antioxidant potential, but their extraction conditions and cellular mechanisms of action remain insufficiently explored. Methods: Ultrasound-assisted extraction was optimized using a 3³ Full Factorial Design (FFD) by investigating temperature (30–50–70 °C), extraction time (1–2–3 h), and solvent composition (water/ethanol). Antioxidant activity was evaluated using multiple in vitro assays, including Total Phenolic Content (TPC), DPPH, ABTS, FRAP, and β-carotene bleaching (BCB) assays. The optimized extract (OE) was chemically characterized by UHPLC–MS/MS and its activity was evaluated in HepG2 cells for biocompatibility, modulation of intracellular ROS levels, and antioxidant pathway activation. Results: Optimal extraction conditions were identified as 30 °C, 70.86 min (1.181 h), and 21.13% ethanol (v/v), yielding an extract with enhanced antioxidant capacity. UHPLC–MS/MS analysis revealed 25 bioactive compounds, mainly flavonoids and phenolic acids, relevant for oxidative stress modulation. The extract significantly reduced tert-butyl hydroperoxide (TBH)-induced intracellular ROS levels, restoring antioxidant proteins involved in the Nuclear Factor erythroid 2-related factor 2 (NRF-2)-mediated defense pathway. Conclusions: The optimized hazelnut skin extract combines strong antioxidant efficacy with cellular compatibility, supporting its potential application as a functional ingredient for nutraceutical and pharmaceutical strategies targeting oxidative stress-related conditions. Full article

Cocoa pod husk (CPH), a major agro-industrial residue, contains valuable bioactive compounds whose recovery can support sustainable waste valorization. This study evaluated the influence of increasing ethanol concentrations on the ultrasound-assisted extraction (UAE) of bioactive compounds from CPH and their antioxidant, antihypertensive, and antihyperglycemic activity. Dried and milled CPH was extracted using ethanol–water mixtures (0–100% ethanol) under fixed ultrasonic conditions. Cocoa pod husk powder characterization and the resulting extracts were analyzed in terms of chemical composition (lignocellulosic compounds, proximate and elemental composition, and bromatological composition), antioxidant capacity, and in vivo antihypertensive and antihyperglycemic effects in Wistar rats. The results showed that solvent polarity strongly modulated extraction efficiency: absolute ethanol yielded the highest phenolic (171.43 mg GAE/g) and flavonoid (132.05 mg QE/g) content, whereas hydroalcoholic mixtures, particularly 50:50, enhanced overall antioxidant performance, especially in FRAP. The chemical analysis results showed the selective recovery of compounds such as quercetin, hesperidin, and theobromine, and FTIR-PCA results revealed distinct solvent-dependent chemical profiles. In vivo assays indicated modest blood pressure stabilization and a more pronounced antihyperglycemic effect after chronic administration. Overall, UAE proved an effective, rapid, and solvent-efficient method for CPH valorization, highlighting its potential for producing natural antioxidants applicable to food, nutraceutical, and cosmetic formulations. Full article

Natural deep eutectic solvents (NADES) offer sustainable alternatives to conventional solvents for plant extraction, yet their influence on extract composition and bioactivity preservation requires further study. Here, choline chloride-based NADES with lactic acid or propylene glycol were evaluated for ultrasound-assisted extraction (60 °C, 30 min, 1:20 w/v) of polyphenol-rich fractions from Sanguisorba officinalis and Symphytum officinale. Spectrophotometric analysis yielded total phenolic contents of 6.49–9.67 mg GAE g⁻¹ and total flavonoids of 0.08–0.52 mg g⁻¹, with values dependent on the plant matrix and the NADES formulation. Targeted HPLC-MS/MS enabled identification of representative phenolic acids (chlorogenic, caffeic, ferulic, rosmarinic) and flavonoid markers (rutin, quercetin derivatives), showing qualitative differences in the detected marker profiles between solvents and matrices. Functional assays demonstrated pronounced antioxidant-related effects, including DPPH radical scavenging at 0.5–25 µg mL⁻¹ (polyphenols), inhibition of lipid peroxidation in rat erythrocytes at 0.25–1.20 µg mL⁻¹, and modulation of mitochondrial respiration and permeability transition in isolated rat liver mitochondria. Overall, the results indicate that choline chloride-based NADES can be used to obtain polyphenol-rich plant extracts compatible with the applied analytical workflow while preserving redox-active fractions, supporting their utility in green analytical sample preparation. Full article

This study investigates the antioxidant, enzyme inhibitory, and antimicrobial activities of water (WEHL) and ethanol (EEHL) extracts of hop (Humulus lupulus) cones. Phytochemical analyses revealed higher total phenolic content in EEHL (271.52 ± 0.13 mg GAE/g) than in WEHL (251.84 ± 0.06 mg GAE/g), as well as higher total flavonoid content (182.56 ± 0.45 mg QE/g for EEHL versus 179.39 ± 0.46 mg QE/g for WEHL). Antioxidant activity, determined by DPPH and ABTS assays, showed that EEHL had stronger radical scavenging capacity with IC₅₀ values of 19.13 ± 4.66 μg/mL (DPPH) and 12.66 ± 1.94 μg/mL (ABTS), compared to WEHL (DPPH: 20.90 ± 2.39 μg/mL; ABTS: 32.41 ± 4.29 μg/mL). In reducing assays, EEHL also showed better absorbance values in FRAP (0.77 ± 0.01), CUPRAC (2.09 ± 0.05), and Fe³⁺ reducing (1.95 ± 0.01) tests. EEHL likely outperformed WEHL due to solvent polarity and extraction efficiency. Moderately polar ethanol extracts a broader range of phenolics and flavonoids, including fewer polar bioactive compounds that contribute to antioxidant capacity and enzyme inhibition. This matches higher TPC/TFC in EEHL and explains stronger radical scavenging, reducing power, and multi-enzyme inhibition. Enzyme inhibition studies revealed that EEHL inhibited acetylcholinesterase (IC₅₀: 26.06 μg/mL), butyrylcholinesterase (IC₅₀: 44.00 μg/mL), α-glycosidase (IC₅₀: 119.31 μg/mL), and carbonic anhydrase isoenzymes hCA I (IC₅₀: 59.78 μg/mL) and hCA II (IC₅₀: 21.19 μg/mL). LC–MS/MS analysis identified major phenolic compounds such as isoquercitrin (3.14 ng/mL), rutin (0.60 ng/mL), and hesperidin (0.43 ng/mL) in EEHL. Antimicrobial screening showed selective activity against Staphylococcus aureus with an inhibition zone of 18.50 ± 0.58 mm, while no inhibition was observed against Escherichia coli and Candida albicans. These findings provide a solvent-dependent in vitro profile that can guide extraction strategies, support antioxidant and multi-enzyme screening (including hCA I and II), and identify candidates for selective antimicrobial evaluation and further preclinical investigation. Despite extensive use of hop extracts, comparative solvent-dependent profiling that links LC–MS/MS phenolic composition with a broad multi-enzyme inhibition panel, including the less frequently evaluated hCA I/II isoenzymes, remains limited. Therefore, the objective of this study was to systematically compare WEHL and EEHL in terms of phytochemical content and in vitro antioxidant, enzyme inhibitory, and antimicrobial activities. Overall, these results provide a solvent-dependent, comparative in vitro profile of WEHL vs. EEHL that can support antioxidant, multi-enzyme screening (including hCA I and II), and selective antimicrobial assays. Full article

Degradable polymers, such as poly(L-lactide) (PLLA), are widely investigated for biomedical applications, including drug delivery systems and temporary implants. Their functionality can be expanded by incorporating degradable metal microparticles that may influence degradation behaviour and enable additional surface modification strategies. In this study, the feasibility of composites consisting of PLLA and biodegradable iron microparticles was investigated. Composites were fabricated by solvent casting, providing a gentle alternative to thermal processing methods, which often compromise polymer integrity. Composites were evaluated by thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy (SEM), tensile testing, dynamic mechanical analysis, and X-ray photoelectron spectroscopy (XPS). Incorporation of iron altered thermal behaviour and crystallinity of PLLA, indicating interactions between polymer matrix and dispersed metal phase that may affect degradation kinetics and material stability. While iron addition reduced Young’s modulus, tensile strength, and elongation at break, composites maintained sufficient structural integrity for potential biomedical applications. XPS and SEM confirmed the embedding of particles within the polymer matrix, enabling potential post-processing approaches. In vitro direct contact and eluate tests demonstrated good cell viability, whereas exposure to free iron particles resulted in dose- and time-dependent cytotoxic effects. Overall, the results demonstrate the feasibility of solvent-cast PLLA–iron composites for resorbable biomedical applications. Full article

This study investigates how porous structure formation influences the properties and safety characteristics of composite rocket propellants. Particular attention was given to approaches that may support more sustainable propellant formulations and processing methods. The work compares the efficiency of different sample-structuring and foaming methods, including a chemical foaming strategy based on two ammonium salts. Additionally, it evaluates the feasibility of generating porosity in propellants containing glycidyl azide polymer through the retention of a low-boiling solvent, remaining from synthesis. This approach is expected to reduce the number of processing steps and simplify them, translating into lessened environmental impact. Propellants incorporating this polymer were found to exhibit consistent low-level porosity and improved performance compared to other ammonium nitrate-based propellants, constituting a potential sustainable alternative to perchlorate-based propellants. The investigation encompassed decomposition kinetics (including decomposition activation energy), combustion product analysis, and exploratory nitrogen porosimetry. From a sustainability perspective, the investigated approach addresses key limitations of perchlorate-based propellants by eliminating chlorine-containing oxidising agents and reducing the need for auxiliary chemicals. In particular, the physical foaming strategy enables pore formation using residual solvent, which is already present in the system, supporting waste minimisation and inherently safer processing. These aspects are discussed in the context of selected principles of Green Chemistry and fundamental properties–sustainability trade-offs. Overall, the results highlight how foaming method selection affects not only propellant behaviour but also opportunities for more resource-efficient and environmentally conscious manufacturing routes. Full article

Non-covalent molecular self-assembly serves as a distinctive strategy for enhancing the mechanical performance of lignin-based composite hydrogels. Nevertheless, the self-assembly process can be significantly influenced, leading to alterations in the nanostructure of the hydrogel, because of the diverse conformational reorganizations of lignin in different solvents. In this research, a solvent exchange process was employed to generate a phase-separated structure comprising hydrophobic lignin domains and hydrophilic poly(N,N-dimethylacrylamide) (PDMA) domains through the aggregation of lignin, thereby forming tough lignin/PDMA hydrogels. By adjusting the solvent composition, the hydrogels exhibit distinct nanostructural transformations that are precisely correlated with the changes in Hansen Solubility Parameters (HSPs) of the solvent mixtures. Balanced HSPs facilitates the formation of small-scale lignin domains with high-domain density, which act as crosslinking points for the establishment of a reinforced network. Remarkably, lignin/PDMA hydrogels prepared at a boundary solvation condition unexpectedly induced the formation of large and highly condensed lignin domains, which displayed a radius of gyration (Rg) of 7.7 nm and an inter-domain distance (d-spacing) of 98.1 nm within the hydrogel network. These unique nanostructural features further contribute to its superior mechanical performance, including excellent tensile strength of 3.2 MPa, Young’s modulus of 5.7 MPa, and fracture energy of 41.2 kJ m⁻², which outperforms most reported lignin hydrogels. Additionally, it offers a strong adhesion and rapid drying approach, rendering the hydrogel more suitable for applications as hydrogel coatings. Full article

Xanthoceras sorbifolium (Yellowhorn) is an underutilized, multipurpose, climate-resilient oilseed with emerging food and industrial potential. This review consolidates current knowledge on its botany, agronomy, kernel composition, extraction technologies, protein and bioactive functionality, food uses, regulatory considerations, and sustainability challenges. Yellowhorn offers high-quality oil with ≈94% unsaturated fatty acids (notably 3.5–4% nervonic acid), while defatted kernel meal contains 31–37% protein (w/w). The matrix also carries bioactives such as tocopherols in the oil (70–530 mg/kg), phytosterols (1420–2970 mg/kg), and saponins (up to 11.62%), alongside flavonoid extracts that show promising antioxidant activity (DPPH EC₅₀ ≈ 10.7 µg/mL). Extraction methods, including cold pressing, solvent systems, and supercritical CO₂, present trade-offs in yield (≈87.8%, ≈60.4–98.04%, and ≈56.5–89.63% respectively), bioactive retention, and scalability, while co-product valorization can improve economic and environmental performance. Regulatory acceptance in the U.S. will likely depend on a refined-oil, specification-driven Generally Recognized as Safe (GRAS) pathway supported by compositional and toxicological evidence. Sustainability priorities include breeding improvements and supply-chain development on marginal lands, valorization of co-products, and integration of life cycle assessment (LCA), both of which are currently under-reported for Yellowhorn. Future directions emphasize process optimization for simultaneous oil-protein recovery, selective purification of functional lipids, encapsulation for stability, and human studies to substantiate claims. Collectively, Yellowhorn represents a promising climate-ready ingredient system requiring targeted research to enable safe, scalable, and sustainable adoption. Full article

Ionic polymer–metal composites consist of an ion-conducting polymer–gel membrane sandwiched between two flexible electrodes, representing a class of soft electroactive materials capable of large deformation under low voltage. The gel membrane, swollen with solvent, facilitates ion migration under an electric field, enabling actuation. Tailoring the interfacial architecture between the electrode and the polymer–gel membrane is pivotal for advancing high-performance IPMC actuators. This study presents a comparative investigation of three core–shell nanocomposite electrodes, fabricated via in situ polymerization, for IPMC applications. Among these, the polyaniline-coated multi-walled carbon nanotube composite exhibits a deliberately designed hierarchical structure, with a specific surface area of 32.345 m²·g⁻¹ and a conductive doped polyaniline shell, as confirmed through XPS analysis. This optimized interface enables superior charge storage and transport, endowing the corresponding electrode with a specific capacitance of 40.28 mF·cm⁻² at 100 mV·s⁻¹—3.2 times greater than that of conventional silver-based electrodes—along with a reduced sheet resistance. When integrated with a Nafion ion–gel membrane, the PANI@MWCNT electrode achieves a 67% increase in force density and a larger displacement output compared to standard devices, directly correlated with its enhanced electrical and electrochemical properties. This work highlights the critical role of core–shell interfacial engineering in governing electromechanical performance at the electrode–gel interface and offers a practical design strategy for developing high-performance, cost-effective IPMC actuators for soft robotics, flexible electronics, and related applications. Full article

The chemical composition of natural products is complex and the investigation of bioactivities of compounds of interest demands their isolation. S. terebinthifolia Raddi is a tree belonging to the Anacardiaceae family and is used in Brazilian folk medicine; its fruit (pink peppers) are used in cooking and its bark in phytomedicine. Extracts of other parts of this plant contain a plethora of components and merit further studies. Countercurrent chromatography (CCC) is frequently employed with natural products due to the high sample recovery rate. The objective of this work was to determine the best solvent system (SS) to fraction the ethanol extracts of leaves, flowers and fruit of Schinus terebinthifolia by CCC and isolate compounds of interest and elucidate their structures through nuclear magnetic resonance (NMR) and mass spectrometry (MS). In addition, antiproliferative, potential cell regeneration and antioxidant activities of the fractions of interest were evaluated. In the present work, three compounds were isolated; two were identified as anacardic acids [(6-(8′, 11′-heptadecadienyl)-salicylic acid and 6-(8′-heptadecenyl)-salicylic acid], as well as (Z)-masticadienoic acid. These compounds showed antiproliferative and potential cell regeneration activities as well as varying degrees of antioxidant capacity. Although these compounds present potential therapeutic activity, more studies are necessary to confirm their safety. Full article

The pods of pea (Pisum sativum L.), an abundant agroindustry by-product, represents a sustainable source of bioactive compounds. To harness these compounds effectively, this study aimed to optimize the ultrasound-assisted extraction (UAE) of polyphenols and plant pigments (chlorophylls and carotenoids) from pea pod waste using response surface methodology, and to evaluate the encapsulation of the resulting extract with a novel pea-based carrier derived from whole pea grain powder. The optimal conditions for the extraction were a time of 45 min, a solid-to-solvent ratio of 1:48 (w/v), and an ethanol concentration of 58.51% (v/v). The extract obtained under these conditions was encapsulated using pea grain powder and compared with a conventional whey protein carrier. The resulting microencapsulates were characterized in terms of process yield, moisture content, particle size distribution, thermal properties, and phenolic composition. Pea grain powder as a carrier provided higher powder yield, lower moisture content, and improved thermal stability, whereas whey protein allowed slightly higher retention of most bioactive compounds, except for coumaric acid and kaempferol. Overall, these findings highlight pea grain powder as a promising plant-based carrier that supports the valorization of pea pod waste, contributing to the development of sustainable ingredients and a circular economy for legume processing by-products. Full article