Search Results (84)

Steam is widely used in industry as a heat carrier for thermal processes and is primarily generated by gas-fired steam boilers. The decarbonization of industrial thermal demand relies on the capability of clean and renewable technologies to provide steam through reliable and cost-effective systems. Concentrating solar thermal technologies are attracting attention as a heat source for industrial steam generation. In addition, electricity-driven high-temperature heat pumps can provide heat using either renewable or grid electricity by upgrading ambient or waste heat to the required temperature level. In this study, linear Fresnel solar collectors and high-temperature heat pumps driven by photovoltaics are considered heat sources for steam generation in industrial processes. Energetic and economic analyses are performed across the European countries to assess and compare their performances. The results demonstrate that for a given available area for the solar field, solar thermal systems provide a higher annual energy yield in southern countries and at lower costs than heat pumps. On the other hand, heat pumps driven by photovoltaics provide higher annual energy for decreasing solar radiation conditions (central and northern Europe), although it leads to higher costs than solar thermal systems. A hybrid scheme combining the two technologies is the favorable option in central Europe, allowing a trade-off between the costs and the energy yield per unit area. Full article

The critical consequence of climate change resulting from global warming is the increase in temperature. In combined cycle power plants (CCPPs), the Electric Power Output (PE) is affected by changes in both Ambient Temperature (AT) and Sea Surface Temperature (SST), particularly in plants utilizing seawater cooling systems. As AT increases, air density decreases, leading to a reduction in the mass of air absorbed by the gas turbine. This change alters the fuel–air mixture in the combustion chamber, resulting in decreased turbine power. Similarly, as SST increases, cooling efficiency declines, causing a loss of vacuum in the condenser. A lower vacuum reduces the steam expansion ratio, thereby decreasing the Steam Turbine Power Output. In this study, the effects of increases in these two parameters (AT and SST) due to global warming on the PE of CCPPs are investigated using various regression analysis techniques, Artificial Neural Networks (ANNs) and a hybrid model. The target variables are condenser vacuum (V), Steam Turbine Power Output (ST Power Output), and PE. The relationship of V with three input variables—SST, AT, and ST Power Output—was examined. ST Power Output was analyzed with four input variables: V, SST, AT, and relative humidity (RH). PE was analyzed with five input variables: V, SST, AT, RH, and atmospheric pressure (AP) using regression methods on an hourly basis. These models were compared based on the Coefficient of Determination (R²), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE), Mean Square Error (MSE), and Root Mean Square Error (RMSE). The best results for V, ST Power Output, and PE were obtained using the hybrid (LightGBM + DNN) model, with MAE values of 0.00051, 1.0490, and 2.1942, respectively. As a result, a 1 °C increase in AT leads to a decrease of 4.04681 MWh in the total electricity production of the plant. Furthermore, it was determined that a 1 °C increase in SST leads to a vacuum loss of up to 0.001836 bar_a. Due to this vacuum loss, the steam turbine experiences a power loss of 0.6426 MWh. Considering other associated losses (such as generator efficiency loss due to cooling), the decreases in ST Power Output and PE are calculated as 0.7269 MWh and 0.7642 MWh, respectively. Consequently, the combined effect of a 1 °C increase in both AT and SST results in a 4.8110 MWh production loss in the CCPP. As a result of a 1 °C increase in both AT and SST due to global warming, if the lost energy is to be compensated by an average-efficiency natural gas power plant, an imported coal power plant, or a lignite power plant, then an additional 610 tCO₂e, 11,184 tCO₂e, and 19,913 tCO₂e of greenhouse gases, respectively, would be released into the atmosphere. Full article

This paper examines how best to use forest wood for energy application, considering that it is a limited natural resource. Eight systems are considered, including wood stoves, steam systems (boiler, power plant, and combined heat and power (CHP)), and gasification combined systems (gas turbine and combined cycle power plant, CHP, and Fischer–Tropsch). The methodology uses energy analysis and modelling and environmental/sustainability considerations to compare the energy systems. In terms of energy conversion efficiency, steam boilers and high-efficiency wood stoves for heating applications provide the highest efficiencies (~80 to 90%) and should be considered. Steam CHP systems provide lower overall energy conversion efficiencies (~75 to 80%) but do provide some electrical energy, and thus should be considered. The use of wood for the production of electricity on its own should not be considered due to low efficiencies (~20 to 30%). Particulate emissions hinder the application of high-efficiency stoves, especially in urban areas, whereas for industrial-scale steam boilers and CHP systems, particle separators can negate this problem. Gasification/Fischer–Tropsch systems have a lower energy efficiency (~30 to 50%); however, a sustainability argument could be made for liquid fuels that have few sustainable alternatives. Full article

Modern power generation aims to maximize the extraction of thermal energy from fossil fuels to produce electricity. Combined cycle power plants, leaders in efficiency, sometimes require an additional steam generator to compensate for insufficient exhaust gas energy in the heat recovery steam generator (HRSG), leading to hybrid combined cycles. This study presents a comprehensive thermodynamic analysis of the hybrid combined cycle power plant located in the Valley of Mexico, operating under both full-load and partial-load conditions. The investigation begins with an energy analysis evaluating key performance parameters under real operating conditions, including the power generation, heat flow supply, thermal efficiency, fuel consumption rates, steam flow, and specific fuel consumption. Subsequently, the analysis examines the performance of the steam cycle using the β factor, which quantifies the relationship between heat flows in the steam generator and the HRSG, to maintain a constant steam flow. This evaluation aims to determine the potential utilization of exhaust gas residual energy for partial steam flow generation in the steam turbine. The study concludes with an exergy analysis to quantify the internal irreversibility flows within the system components and determine the overall exergy efficiency of the power plant. The results demonstrate that, under 100% load conditions, the enhanced utilization of exhaust gases from the HRSG leads to fuel savings of 33,903.36 tons annually and increases the exergy efficiency of the hybrid combined cycle power plant to 54.08%. Full article

With the increase in the amount of new energy in new power systems, the response speed of power demand changes in combined cycle gas turbines (CCGTs) is facing new challenges. This paper studies an integrated operation strategy for the coupled molten salt energy storage of CCGT systems, and analyzes the system through simulation calculation. The advantages of the coupled system are determined by comparing the electrical output regulation capability, thermoelectric ratio, gas consumption rate, and peaking capacity ratio. In addition, using stored energy to maintain the temperature of the heat recovery steam generator (HRSG) can shorten the system’s restart time, improve the unit’s operating efficiency, and reduce the start-up cost. Our findings can be used as a reference for accelerating the performance improvement of CCGT systems, which is also crucial in technologies for waste heat recovery, molten salt energy storage technology, and promoting the sustainable development of energy systems. Full article

This work presents a novel trigeneration system for the simultaneous production of desalinated water, electrical energy, and cooling, addressing the challenges of water scarcity and climate change through an integrated and efficient approach. The proposed system combines an 8-stage Multi Stage Flash Distillation (MSF) process with a 6-effect Multiple Effect Distillation (MED) process, complemented by an expander-generator to optimize steam utilization. Cooling production is achieved through a dual ejectocondensation mechanism, which enhances energy recovery and expands operational flexibility. The system’s performance was analyzed using Aspen Plus simulations, demonstrating technical feasibility across a broad operating range: 28.3 to 0.8 kPa and 68 to 4 °C. In cogeneration mode, the system achieves a Performance Ratio (PR) of 12.06 and a Recovery Ratio (RR) of 54%, producing 67,219.2 L/day of desalinated water and reducing electrical consumption by 12.03%. In trigeneration mode, it achieves a PR of 17.81 and an RR of 80%, with a cooling capacity of 1225 kW, generating 99,273.6 L/day of desalinated water while reducing electrical consumption by 3.69%. These results underscore the system’s capability to significantly enhance the efficiency and capacity of thermal desalination technologies, offering a sustainable and high-performing solution for coastal communities worldwide. Full article

This study analyzes the thermodynamic and economic viability of modified high-temperature gas-cooled reactor (HTGR) gas-steam combined heat and power (CHP) systems compared to conventional CHP plants. The research addresses the critical need for efficient and sustainable energy production methods. Using comprehensive thermodynamic modeling and economic analysis, the study evaluates system performance under various operating conditions. Key findings reveal that modified CHP plants with HTGR and turboexpanders (TEs) demonstrate significantly higher efficiency and lower heat generation costs compared to conventional gas turbine (GT) CHP plants, despite higher initial capital investments. The modified systems achieve electricity generation efficiencies up to 48%, surpassing traditional nuclear power plants. The absence of CO₂ emissions and lower fuel costs in HTGR systems contribute to their economic advantage. This research provides novel insights into the potential of HTGR technology in CHP applications, offering a promising solution for future energy systems. The study’s originality lies in its comprehensive comparison of conventional and modified CHP systems, considering both thermodynamic and economic aspects, which has not been extensively explored in existing literature. Full article

Today, most of the world’s electric energy is generated by burning hydrocarbon fuels, which causes significant emissions of harmful substances into the atmosphere by thermal power plants. In world practice, flue gas cleaning systems for removing nitrogen oxides, sulfur, and ash are successfully used at power facilities but reducing carbon dioxide emissions at thermal power plants is still difficult for technical and economic reasons. Thus, the introduction of carbon dioxide capture systems at modern power plants is accompanied by a decrease in net efficiency by 8–12%, which determines the high relevance of developing methods for increasing the energy efficiency of modern environmentally friendly power units. This paper presents the results of the development and study of the process flow charts of binary and trinary combined-cycle gas turbines with minimal emissions of harmful substances into the atmosphere. This research revealed that the net efficiency rate of a binary CCGT with integrated post-combustion technology capture is 39.10%; for a binary CCGT with integrated pre-combustion technology capture it is 40.26%; a trinary CCGT with integrated post-combustion technology capture is 40.35%; and for a trinary combined-cycle gas turbine with integrated pre-combustion technology capture it is 41.62%. The highest efficiency of a trinary CCGT with integrated pre-combustion technology capture is due to a reduction in the energy costs for carbon dioxide capture by 5.67 MW—compared to combined-cycle plants with integrated post-combustion technology capture—as well as an increase in the efficiency of the steam–water circuit of the combined-cycle plant by 3.09% relative to binary cycles. Full article

Growing environmental concerns have driven the installation of renewable systems. Meanwhile, the continuous decline in the levelized cost of energy (LCOE), alongside the decreasing cost of photovoltaics (PVs), is compelling the power sector to accurately forecast the performance of energy plants to maximize plant profitability. This paper presents a comprehensive analysis and optimization of a hybrid power generation system for a remote community in the Middle East and North Africa (MENA) region, with a 10 MW peak power demand. The goal is to achieve 90 percent of annual load coverage from renewable energy. This study introduces a novel comparison between three different configurations: (i) concentrated solar power (parabolic troughs + thermal energy storage + steam Rankine cycle); (ii) fully electric (PVs + wind + batteries); and (iii) an energy mix that combines both solutions. The research demonstrates that the hybrid mix achieves the lowest levelized cost of energy (LCOE) at 0.1364 USD/kWh through the use of advanced transient simulation and load-following control strategies. The single-technology solutions were found to be oversized, resulting in higher costs and overproduction. This paper also explores a reduction in the economic scenario and provides insights into cost-effective renewable systems for isolated communities. The new minimum cost of 0.1153 USD/kWh underscores the importance of integrating CSP and PV technologies to meet the very stringent conditions of high renewable penetration and improved grid stability. Full article

A Type 22 Broadsword class of frigate uses a combined gas or gas (COGOG) propulsion system that utilizes four different gas turbines, depending on the mode of operation. Its twin ST40M cruise gas turbines are operational most frequently, and an increase in their efficiency would significantly impact fuel usage and ship range. This study evaluates the option to upgrade the cruise gas turbines to a combined gas turbine–electric and steam (COGES) system, which utilizes a steam Rankine cycle to recover energy from the exhaust gases of the gas turbine. An alternative system using hot air is also analyzed for performance comparison. The analysis contains calculations for the energy extraction and dimensions of heat exchangers, for the power extracted from the additional steam or air turbine and for pressure losses of the exhaust gas. Different configurations for the heat exchangers were investigated, as well as various parameters for the steam and hot air. The size and mass of the system were an important aspect of the analysis. It was concluded that an auxiliary system operating at a maximum steam pressure of 20 bar could generate an additional 771 kW of power while adding a mass of 7.4 tons to the frigate. These findings suggest that upgrading to a COGES system could cover the electricity needs of the entire ship and thus reduce the overall fuel consumption, resulting in lower operational costs and less emissions. Full article

The transition towards a sustainable and renewable energy future is essential to mitigate climate change and reduce greenhouse gas emissions. Small–medium combined heat and power (CHP) systems are increasingly popular for distributed energy generation, as they offer improved energy efficiency and reduced emissions compared to traditional power generation systems. This article reviews recent research articles related to small–medium CHP systems, including their role in renewable energy systems, use of biofuels, steam injection, diagnostics, and carbon capture. Throughout the research, the high potential of coastal regions has been observed and studied as a solid base for the later development of CHP systems. Based on the reviewed literature, the highest potential solutions are proposed to be further investigated as an efficient, economical solution for generating electricity and heat for various small-scale applications. Full article

Rising energy demands, the depletion of fossil fuels, and their environmental impact necessitate a shift towards sustainable power generation. Concentrating solar power (CSP) offers a promising solution. This study examines a hybridization of a combined cycle power plant (CCPP) based on solar energy with fossil fuel and energy storage in rock layers to increase Saudi Arabia’s electricity production from renewable energy. The fuel is used to keep the temperature at the inlet of the gas turbine at 1000 °C, ensuring the power produced by the Rankine cycle remains constant. During the summer, the sun is the main source of power generation, whereas in the winter, reliance on fuel increases significantly. The Brayton cycle operates for 10 h during peak solar radiation periods, storing exhaust heat in rock beds. For the remaining 14 h of the day, this stored heat is discharged to operate the Rankine steam cycle. Simulations and optimizations are performed, and the system is evaluated using a comprehensive 4E analysis (energy, exergy, exergoconomic, and environmental) alongside a sustainability assessment. A parametric evaluation examines the effect of key factors on system performance. The rock bed storage system compensates for solar intermittency, enabling power generation even without sunlight. The study reveals that the system generated 12.334 MW in June, achieving an energy efficiency of 37% and an exergy efficiency of 40.35%. The average electricity cost during this period was 0.0303 USD/kWh, and the carbon footprint was 0.108 kg CO₂/kWh. In contrast, during January, the system produced 13.276 MW with an energy efficiency of 37.91% and an exergy efficiency of 44.16%. The average electricity cost in January was 0.045 USD/kWh, and the carbon footprint was 0.1 kg CO₂/kWh. Interestingly, solar energy played a significant role: it contributed 81.42% of the heat in June, while in January, it accounted for 46.77%. The reduced electricity costs during June are primarily attributed to the abundant sunshine, which significantly powered the system. Full article

While there are software tools available for helping to conduct life cycle assessment (LCA), such as OpenLCA, these tools lack integration with process design, simulation, and optimization software. As LCA has a critical role in sustainable product design, this paper presents a platform called EMSO_OLCA, which integrates the LCA provided by OpenLCA into the Environment for Modeling, Simulation, and Optimization (EMSO). EMSO_OLCA incorporates a database of environmental impact assessment methodologies from OpenLCA and aligns with the principles of LCA outlined in ISO 14040 and ISO 14044. Validation tests were conducted to compare the results obtained by the LCA of sugarcane ethanol using OpenLCA and EMSO_OLCA, revealing a high level of agreement. The average relative error was 0.045%, indicating a negligible discrepancy between the tools. Moreover, it took only 0.3 s for the calculation, which is desirable for use with process system engineering tools. A second case study was applied to combined steam and electricity production from the combustion of sugarcane bagasse and straw in a combined heat and power system. The results show the integration of LCA with simulation and sensitivity analysis tools, thus supporting sustainable decision-making processes. EMSO_OLCA bridges the gap between LCA and process engineering, enabling a holistic approach to the sustainability, design, and implementation of environmentally friendly solutions. Full article

Adopting biomass energy as an alternative to fossil fuels for electricity production presents a viable strategy to address the prevailing energy deficits and environmental concerns, although it faces challenges related to suboptimal energy efficiency levels. This study introduces a novel combined cooling and power (CCP) system, incorporating an externally fired gas turbine (EFGT), steam Rankine cycle (SRC), absorption refrigeration cycle (ARC), and organic Rankine cycle (ORC), aimed at boosting the efficiency of biomass integrated gasification combined cycle systems. Through the development of mathematical models, this research evaluates the system’s performance from both thermodynamic and exergoeconomic perspectives. Results show that the system could achieve the thermal efficiency, exergy efficiency, and levelized cost of exergy (LCOE) of 70.67%, 39.13%, and 11.67 USD/GJ, respectively. The analysis identifies the combustion chamber of the EFGT as the component with the highest rate of exergy destruction. Further analysis on parameters indicates that improvements in thermodynamic performance are achievable with increased air compressor pressure ratio and gas turbine inlet temperature, or reduced pinch point temperature difference, while the LCOE can be minimized through adjustments in these parameters. Optimized operation conditions demonstrate a potential 5.7% reduction in LCOE at the expense of a 2.5% decrease in exergy efficiency when compared to the baseline scenario. Full article

Libya is facing a serious challenge in its sustainable development because of its complete dependence on traditional fuels in meeting its growing energy demand. On the other hand, more intensive energy utilization accommodating multiple energy resources, including renewables, has gained considerable attention. This article is motivated by the obvious need for research on this topic due to the shortage of applications concerning the prospects of the hybridization of energy systems for electric power generation in Libya. The 283 MW single-cycle gas turbine operating at the Sarir power plant located in the Libyan desert is considered a case study for a proposed Integrated Solar Combined Cycle (ISCC) system. By utilizing the common infrastructure of a gas-fired power plant and concentrating solar power (CSP) technology, a triple hybrid system is modeled using the EES programming tool. The triple hybrid system consists of (i) a closed Brayton cycle (BC), (ii) a Rankine cycle (RC), which uses heat derived from a parabolic collector field in addition to the waste heat of the BC, and (iii) an organic Rankine cycle (ORC), which is involved in recovering waste heat from the RC. A thermodynamic analysis of the developed triple combined power plant shows that the global power output ranges between 416 MW (in December) and a maximum of 452.9 MW, which was obtained in July. The highest overall system efficiency of 44.3% was achieved in December at a pressure ratio of 12 and 20% of steam fraction in the RC. The monthly capital investment cost for the ISCC facility varies between 52.59 USD/MWh and 58.19 USD/MWh. From an environmental perspective, the ISCC facility can achieve a carbon footprint of up to 319 kg/MWh on a monthly basis compared to 589 kg/MWh for the base BC plant, which represents a reduction of up to 46%. This study could stimulate decision makers to adopt ISCC power plants in Libya and in other developing oil-producing countries. Full article