Search Results (25)

This study investigated the sustainability aspects of implementing a small-scale biogas digester project at the EARTH Centre, a horse-riding facility for the disabled, in South Africa. Firstly, an energy audit of the facility was conducted. From this exercise, energy-saving opportunities through anaerobic digestion of horse manure were identified. Biomethane potential tests (BMPs) were then performed using the Automatic Methane potential test system II (AMPTS II) of BioProcess Control (Lund, Sweden). The horse manure BMP result was 106 L/kg.VS with the biogas averaging a methane content of 40%. This BMP was lower than that of common substrates such as cow manure which can range from 150–210 L/kg.VS. The gas production rate was almost constant in the first 13 days indicating a long hydrolysis period for horse manure. The microbial species in the digester did not change much during the incubation period although small changes were visible in the proportions of each species as the reaction progressed from start to finish. The energy audit showed that 47% of the EARTH Centre’s energy requirements, which equated to 14,372 kWh/year, could be secured from biogas or solar instead of obtaining it from the national grid which is powered mainly by unsustainable coal-fired systems. As a starting point, a 10 cubic meter biogas digester was installed to produce 5512 kWh of energy per year in the form of biogas. To boost biogas production and continue running the system smoothly, it was evident that the horse manure-fed digester would require regular spiking with cow manure as a bioaugmentation strategy. The digester also produced bio-fertiliser and several sustainable development goals were fulfilled by this project. Current efforts are focused on process optimization of this technology at the Earth Centre to further improve the sustainability of the whole business. Full article

The rapid growth of the world population led to an exponential growth in industrial activity all around the world. Consequently, CO₂ emissions have risen almost 400% since 1950 due to human activities. In this context, microalgae biomass has emerged as a renewable and sustainable feedstock for producing third-generation biofuels. This study explores the laboratory-scale production of bioethanol and biomethane from dried algal biomass. The first step was to evaluate and optimize the production of glucose from the biomass. Thus, three different techniques with three different solvents were tested to identify the most effective and efficient in terms of saccharification yield. With the assistance of an autoclave or a high-temperature water bath and 0.2 M NaOH as a solvent, yields of 79.16 ± 3.03% and 85.73 ± 3.23% were achieved which correspond to 9.24 and 9.80 g/L of glucose, respectively. Furthermore, the most efficient method from the pretreatment step was chosen to carry out a factorial design to produce bioethanol. The experiments showed that the loading of cellulase was of crucial importance to the optimization of the process. Optimized ethanolic fermentation yielded ethanol concentrations up to 4.40 ± 0.28 g/L (76.12 ± 4.90%) (0.3 Μ NaOH, 750 μL/g_cellulose and 65 μL/g_starch), demonstrating the critical role of cellulase loading. Biomethane potential (BMP) assays on fermentation residues showed increased yields compared to untreated feedstock, with a maximum methane yield of 217.88 ± 10.40 mL/gVS. Combined energy production from bioethanol and biomethane was calculated at up to 1044.48 kWh/tn of algae feedstock, with biomethane contributing 75.26% to the total output. These findings highlight the potential of integrated algae-based biorefineries to provide scalable and sustainable biofuel solutions, aligning with circular economy principles. Full article

The collection and use of Sargassum spp. as feedstock for the production of valuable products such as biomethane by anaerobic digestion (AD) would mitigate the negative impact of the blooms and the costs related to waste management in the Dominican Republic. In this work, the effect of the particle size of pelagic Sargassum spp. biomass, as a result of mechanical pretreatments, on the biomethanation was determined. The granulometric analysis of the mechanically pre-treated biomass was carried out using a Mastersize2000. The Biochemical Methane Potential (BMP) of the samples was determined using an Automatic Potential System Test II (AMPTS^® II). The kinetic parameters of the reaction were scientifically evaluated by using First order kinetic Model and modified Gompertz Model. The granulometric analysis showed a monomodal distribution on crushed biomass (505 µm) and a bimodal distribution on the milling sample (107 µm). The bimodal biomass means the biomass is characterized by the presence of fine and large particles. We observed that BMP increased by 78.85% when particles were reduced from 50,000 µm to 505 µm and by 73.61% when particles were reduced from 50,000 µm to 107 µm. A low methane yield from the milling biomass (107 µm) compared to the crushed biomass (505 µm) could be related to the excessive reduction of particle size. The fine particles are subject to the formation of aggregates and consequently, the contact area between the algae cells and the microorganisms that operate the anaerobic digestion process decreases. Full article

Biogas from lignocellulosic feedstock is a promising energy source for decentralized renewable electricity, heat, and/or vehicle fuel generation. However, the selection of a suitable energy crop should be based on several factors such as biomass yields and characteristics or biogas yields and economic returns if used in biorefineries. Furthermore, the food-to-fuel conflict for the use of a specific energy crop must be mitigated through smart cropping techniques. In this study, the potential use of sweet sorghum as an energy crop grown during the fallow periods of sugarcane cultivation was evaluated. Nine sweet sorghum cultivars were grown on sandy loam soil during September 2020 in North Queensland, Australia. The overall results showed that the crop maturity had a profound influence on chemical composition and biomass yields. Further, the total insoluble and soluble sugar yields varied among the tested cultivars and were dependent on plant height and chemical composition. The biomass yields ranged from 46.9 to 82.3 tonnes/hectare (t/ha) in terms of the wet weight (w/w) of the tested cultivars, with the SE-81 cultivar registering the highest biomass yield per hectare. The gross energy production was determined based on the chemical composition and methane yields. Biochemical methane potential (BMP) studies in batch experiments at 37 °C showed that methane yields of 175 to 227.91 NmL CH₄/gVS_added were obtained from the tested cultivars. The maximum methane yield of 227.91 NmL CH₄/gVS_added was obtained for cultivar SE-35. However, SE-81 produced the highest methane yields on a per hectare basis (3059.18 Nm³ CH₄/ha). This is equivalent to a gross energy value of 761.74 MWh/year or compressed biomethane (BioCNG) as a vehicle fuel sufficient for 95 passenger cars travelling at 10,000 km per annum. Overall, this study demonstrated that sweet sorghum is a potential energy crop for biogas production that could be cultivated during the fallow period of sugarcane cultivation in Queensland. Full article

Bioplastics have emerged as a promising alternative to conventional plastics, marketed as environmentally friendly and sustainable materials. They provide a variety of methods for efficient waste management contributing to the goals of the circular economy. At their end-of-life stage, bioplastics can generate added value through aerobic and anaerobic biological treatments (composting or anaerobic digestion). In this study, biomethane potential (BMP) tests were carried out under mesophilic conditions on eight different catering biodegradable plastics available in the market and certified as being biodegradable under industrial composting conditions. Chemical analysis of the biodegradable plastics included elemental analysis, Fourier-transform infrared spectroscopy, and inductively coupled plasma–optical emission spectrometry. Key differences were observed in total solids (TS) and volatile solids (VS) contents between the studied biopolymer products. TS values ranged between 85.00 ± 0.26% (Product 8) and 99.16 ± 0.23% (Product 4), whereas VS content ranged between 64.57 ± 0.25 %wm (Product 6) and 99.14 ± 0.17 %wm (Product 4). Elemental analysis (elements C, H, N, S, and O) was used to estimate the theoretical methane production (ThBMP) of each product. The highest ThBMP (538.6 ± 8.7 NmL/gVS) was observed in Product 4 correlated with the highest C and H contents, while the lowest ThBMP (431.8 ± 6.1 NmL/gVS) was observed in Product 2. Significant differences were recorded between BMP values according to the chemical composition of the polymers. The average of BMP values ranged between 50.4 ± 2.1 NmL/gVS and 437.5 ± 1.0 NmL/gVS. Despite being characterized by the same composition (cellulose/cellulose derivatives and calcium carbonate), Products 2, 3, and 6 revealed significant differences in terms of TS, VS, ThBMP, and BMP. Furthermore, a significant statistical relationship (p < 0.001) was found between time (days) and BMP values of the eight products (R² = 0.899–0.964) during the initial phase. The study confirmed that cellulose-based materials can convert efficiently under mesophilic conditions into methane, at a relatively short retention time; hence, they can be regarded as a promising material for co-digestion with feedstock in industrial anaerobic biogas plants. In contrast, biodegradation of polylactic acids (PLA) does not occur under mesophilic conditions, and hence, pre-treatment of the polymers is recommended. Moreover, PLA-containing products are highly affected by the presence of other components (e.g., polybutylene adipate terephthalate and cellulose/cellulose derivatives). Full article

Reducing the phenomenon of food waste and effective management of already wasted food in the form of post-consumer waste, included in the source-separated organic fraction of municipal solid waste (SS-OFMSW) from households and catering facilities, are some of the key challenges of the circular economy (CE), in particular in highly urbanized areas. The basis for the effective use of this waste is the knowledge of its physical and chemical properties. The main objective of the paper is to identify the key technological and organizational parameters for selective collection determining the characteristics of the SS-OFMSW and, consequently, the optimal path for its management. This paper presents the results of qualitative research of SS-OFMSW generated in the capital of Poland—Warsaw—coming from three sources: multi- and single-family housing and catering facilities. The collection efficiency of this waste was determined in the form of quality in container rate (QCR = 92–97%) and variability in terms of impurities and admixtures present in it (CV = 56–87%). High variability indicates that the system of selective waste collection in Warsaw is immature, which may hinder undertaking activities in the field of waste management planning. The study confirmed the suitability of the tested SS-OFMSW for organic recycling, especially using anaerobic digestion (AD), to which it is predisposed by water content, C/N, and biomethane potential (BMP). All tested food waste is characterized by a high yield of biogas in the range of 384–426 m³/Mg VS and an average share of methane in biogas at the level of 52–61%. Fertilizer properties, moisture, and its gas potential show little variability (CV ≤ 16%), which means that these data can be treated as stable data. The obtained results indicate the optimal direction for the collection and processing of SS-OFMSW based on post-consumer food waste in urbanized areas. Full article

Anaerobic digestion (AD) of sewage sludge can be optimised by adding trade wastes (TWs) because of their nutrient content and boost in biogas formation if non-inhibitory. However, some components in TWs might have an inhibitory impact, such as nitrogen compounds, sulphate, heavy metals, metalloids, halogens and organic pollutants (e.g., phenol). This study aimed to understand the impact of TWs on the co-digestion with sewage sludge to identify appropriate TW loads for sustainable AD operation. The composition of 160 TWs was evaluated and the constituents with potential to cause inhibition or toxicity were tested in bio-methane potential (BMP) tests. The compounds studied in BMP tests included ammonia, zinc, copper, aluminium, mercury, arsenic, chloride, sulphate and nitrate. An improvement was observed at concentrations 2–746 mg Zn/L, 1066–2821 mg Cl/L as zinc sulphate and sodium chloride in biogas production, and 2–746 mg Zn/L, 162 mg SO₄/L, 25 mg Hg/L as zinc sulphate, sodium chloride and mercury sulphate in methane production, respectively. Considering the TWs characterised and the results of the BMP tests, a volumetric ratio of 10/90 of TWs and sewage sludge is proposed as a suitable feedstock for co-digestion. Full article

This study highlighted the influence of molasses residue (MR) on the anaerobic treatment of cow manure (CM) at various organic loading and mixing ratios of these two substrates. Further investigation was conducted on a model-fitting comparison between a kinetic study and an artificial neural network (ANN) using biomethane potential (BMP) test data. A continuous stirred tank reactor (CSTR) and an anaerobic filter with a perforated membrane (AF) were fed with similar substrate at the organic loading rates of (OLR) 1 to OLR 7 g/L/day. Following the inhibition signs at OLR 7 (50:50 mixing ratio), 30:70 and 70:30 ratios were applied. Both the CSTR and the AF with the co-digestion substrate (CM + MR) successfully enhanced the performance, where the CSTR resulted in higher biogas production (29 L/d), SMP (1.24 LCH₄/gVS_added), and VS removal (>80%) at the optimum OLR 5 g/L/day. Likewise, the AF showed an increment of 69% for biogas production at OLR 4 g/L/day. The modified Gompertz (MG), logistic (LG), and first order (FO) were the applied kinetic models. Meanwhile, two sets of ANN models were developed, using feedforward back propagation. The FO model provided the best fit with Root Mean Square Error (RMSE) (57.204) and correlation coefficient (R²) 0.94035. Moreover, implementing the ANN algorithms resulted in 0.164 and 0.97164 for RMSE and R², respectively. This reveals that the ANN model exhibited higher predictive accuracy, and was proven as a more robust system to control the performance and to function as a precursor in commercial applications as compared to the kinetic models. The highest projection electrical energy produced from the on-farm scale (OFS) for the AF and the CSTR was 101 kWh and 425 kWh, respectively. This investigation indicates the high potential of MR as the most suitable co-substrate in CM treatment for the enhancement of energy production and the betterment of waste management in a large-scale application. Full article

Slaughterhouse wastewater (SHWW) has a great potential to generate biomethane energy when subjected to anaerobic digestion (AD). Nonetheless, the process is susceptible and prone to failure because of slow hydrolysis and the production of inhibitory compounds. Accordingly, to address this deficiency, anaerobic co-digestion (ACoD) is used to improve the treatment efficiency of the monodigestion of this high-strength waste and thereby increase methane production. The current investigation utilized the biochemical methane potential (BMP) test to assess the treatment performance of co-digested SHWW with sugar press mud (SPM) for improving biomethane energy recovery. It was established that the ACoD of SHWW with SPM increased methane (CH₄) yield, enhanced organic matter removal efficiency and improved process stability, while also presenting synergistic effects. The anaerobic monodigestion (AMoD) of SHWW (100SHWW: 0SPM) showed a higher CH₄ yield (348.40 CH₄/g VS) compared with SPM (198.2 mL CH₄/g VS). The 80% SPM: 20% SHWW mix ratio showed the optimum results with regard to organic matter removal efficiency (67%) and CH₄ yield (478.40 mL CH₄/g VS), with increments of 27% and 59% compared with AMoD of SHWW and SPM, respectively. However, it is also possible to achieve 5% and 46% CH₄ yield increases under a 40% SPM: 60% SHWW mix proportion in comparison to the AMoD of SHWW and SPM, respectively. Furthermore, kinetic analysis of the study using a modified Gompertz model revealed that the CH₄ production rate increased while the lag time decreased. The synergistic effects observed in this study demonstrate that incorporating SPM into the substrate ratios investigated can improve the AD of the SHWW. In fact, this represents the environmental and economic benefits of successfully implementing this alternative solution. Bioenergy recovery could also be used to supplement the country’s energy supply. This would help to increase the use of cleaner energy sources in electricity generation and heating applications, reducing the greenhouse gas effect. Full article

Circular economy aims to eliminate organic waste through its transformation, composting and processing into other products or energy. The main aim of the study was to determine the specific methane yield (SMY) of anaerobic digestion (AD) of four different fruit and vegetable residues (FVR). In addition, the reduction in greenhouse gas (GHG) emissions was calculated based on the assumption that maize will be replaced by the FVR as a feedstock for biogas production. The SMY of four residues (apple pomace, cabbage leaves, pumpkin peels and fibrous strands and walnut husks) was measured in the biomethane potential test (BMP) in wet anaerobic digestion technology. The highest SMY (297.81 ± 0.65 NL kg_VS⁻¹) was observed for cabbage leaves while the lowest SMY (131.07 ± 1.30 kg_VS⁻¹) was found for walnut husks. The concentrations of two inhibitory gasses (NH₃ and H₂S) in biogas were low and did not affect the AD process. Only biogas produced from cabbage leaves was characterised by higher NH₃ and H₂S concentrations resulting from the highest protein concentration in this waste. FVR used as feedstock in biogas production may decrease the area of maize cultivation. Therefore, the GHG emissions from maize cultivation will be reduced. In Poland only, the use of four studied FVR as feedstock for biogas production would contribute to the reduction of GHG emissions by 43,682 t CO₂ eq. Full article

The olive alperujo (OA) corresponds to the solid waste generated in the olive oil extraction process using the two-phase centrifugation method. OA is produced in large quantities (800 kg OA/ton olives processed) and is characterized by its high moisture content, organic matter, and low pH. In Chile, the olive oil industry is recent, and one of its main challenges is to be able to manage OA to reduce the impact caused by its disposal. In this sense, its valorization as biogas by means of anaerobic digestion is an economically attractive option. For this, it is previously necessary to evaluate the biomethane potential (BMP) of the raw OA using batch assays. This study was focused on evaluating the factors that most affect the methane yield (MY) when using OA as substrate in BMP tests. First, a sweep analysis (Plackett–Burman) was applied to determine those factors that, according to the literature, would have an influence on the BMP tests. Among the factors studied, the most significant were preincubation, OA concentration, and agitation level. Subsequently, a 2³ factorial experimental design was applied to evaluate the effect of these factors on MY at different levels. Results show that the OA concentration was the most significant factor affecting MY. Full article

Hydrothermal carbonisation (HTC) can be integrated with anaerobic digestion (AD) for the treatment of digestate, resulting in a solid hydrochar or bio-coal and a process water, which can be recirculated back into AD to produce biogas. The properties of digestate-derived hydrochars do not lend themselves to producing high quality bio-coal and blending with lignocellulosic feedstocks can improve its properties. This study investigates the co-processing of sewage sludge (SS) digestate with three lignocellulosic biomass (grass, privet hedge, and woodchip). The calorific value of the resulting bio-coal is increased following co-processing, although feedstock interactions result in non-additive behaviour. The largest increase in calorific value was observed for co-processing with woodchip. There is evidence for non-additive partitioning of metals during co-processing resulting in only moderate improvements in ash chemistry during combustion. Co-processing also effects the composition of process waters, influencing the potential for biogas production. Experimental biomethane potential (BMP) tests indicate that grass clippings are the most suitable co-feedstock for maintaining both calorific value and biogas production. However, above 200 °C, BMP yields appear to decrease, suggesting the process water may become more inhibitory. Co-processing with wood waste and privet hedge produce the higher CV bio-coal but significantly reduced BMP. Full article

The organic fraction resulting from the separate collection of municipal solid waste (OFMSW) is an abundant residue exploitable for biofuel production. Anaerobic digestion (AD) is one of the most attractive technologies for the treatment of organic wastes thanks to the generation of biogas with a high methane content. However, because of its complex composition, the direct digestion of OFMSW can be less effective. To overcome these difficulties, many pretreatments are under development. In this work, the efficacy of alkaline hydrogen peroxide (AHP) oxidation was assessed for the first time as a pretreatment of OFMSW to enhance its anaerobic biodegradability. In this regard, many AHP batch tests were executed at pH 9 and by changing the peroxide dosages up to 1 g_H2O2/g_COD, under room temperature and pressure conditions. Afterwards, biomethane potential tests (BMP) were conducted to evaluate the performance of anaerobic digestion both on raw and pretreated OFMSW. The pretreatment tests demonstrated that AHP induces only a weak reduction in the organic load, reaching a maximum COD removal of about 28%. On the other hand, notable productions of volatile fatty acids (VFA) were found. In fact, by applying a peroxide dose of just 0.025 g_H2O2/g_COD, there was a doubling in VFA concentration, which increased by five times with the highest H₂O₂ amount. These results indicate that AHP mainly causes the conversion of complex organic substrates into easily degradable compounds. This conversion made it possible to achieve much better performance during the BMP tests conducted with the pretreated waste compared to that carried out on fresh OFMSW. Indeed, a low methane production of just 37.06 mL_CH4/g_TS was detected on raw OFMSW. The cumulated CH₄ production in the pretreated samples increased in response to the increase in H₂O₂ dosage applied during AHP. Maximum specific productions of about 463.7 mL_CH4/g_TS and 0.31 L_CH4/g_CODremoved were calculated on mixtures subjected to AHP. On these samples, the satisfactory evolution of AD was confirmed by the process parameters calculated by modeling the cumulated CH₄ curves through a new proposed formulation of the Gompertz equation. Full article

The present study evaluates the digestion of cork boiling wastewater (CBW) through a biochemical methane potential (BMP) test. BMP assays were carried out with a working volume of 600 mL at a constant mesophilic temperature (35 °C). The experiment bottles contained CBW and inoculum (digested sludge from a wastewater treatment plant (WWTP)), with a ratio of inoculum/substrate (Ino/CBW) of 1:1 and 2:1 on the basis of volatile solids (VSs); the codigestion with food waste (FW) had a ratio of 2/0.7:0.3 (Ino/CBW:FW) and the codigestion with cow manure (CM) had a ratio of 2/0.5:0.5 (Ino/CBW:CM). Biogas and methane production was proportional to the inoculum substrate ratio (ISR) used. BMP tests have proved to be valuable for inferring the adequacy of anaerobic digestion to treat wastewater from the cork industry. The results indicate that the biomethane potential of CBWs for Ino/CBW ratios 1:1 and 2:1 is very low compared to other organic substrates. For the codigestion tests, the test with the Ino/CBW:CM ratio of 2/0.7:0.3 showed better biomethane yields, being in the expected values. This demonstrated that it is possible to perform the anaerobic digestion (AD) of CBW using a cosubstrate to increase biogas production and biomethane and to improve the quality of the final digestate. Full article

Most biogas plants in the world run under psychrophilic conditions and are operated by small and medium farmers. There is a gap of knowledge on the performance of these systems after several years of operation. The aim of this research is to provide a complete evaluation of a psychrophilic, low-cost, tubular digester operated for eight years. The thermal performance was monitored for 50 days, and parameters such as pH, total volatile fatty acid (tVFA), chemical oxygen demand (COD) and volatile solids (VS) were measured every week for the influent and effluent. The digester operated at a stabilized slurry temperature of around 17.7 °C, with a mean organic load rate (OLR) equal to 0.52 kg VS/m³_digester *d and an estimated hydraulic retention time (HRT) of 25 days. The VS reduction in the digester was around 77.58% and the COD reduction was 67 ± 3%, with a mean value for the effluent of 3.31 ± 1.20 g COD/Lt, while the tVFA decreased by 83.6 ± 15.5% and the presence of coliforms decreased 10.5%. A BioMethane potential test (BMP) for the influent and effluent showed that the digester reached a specific methane production of 0.40 Nm³CH₄/kg VS and a 0.21 Nm³CH₄/m³_digester d with 63.1% CH₄ in the biogas. These results, together with a microbiological analysis, show stabilized anaerobic digestion and a biogas production that was higher than expected for the psychrophilic range and the short HRT; this may have been due to the presence of an anaerobic digestion microorganism consortium which was extremely well-adapted to psychrophilic conditions over the eight-year study period. Full article