Search Results (3,869)

Semi-circular bending tests were conducted on high-elasticity asphalt concrete under different aging conditions to investigate the effects of rubber particles and polyester fiber contents on its fracture properties. Results showed that the incorporation of approximately 3% rubber particles increased the fracture energy by 15%, whereas the addition of 1.2% polyester fibers increased the fracture toughness and fracture energy by 4% and 19%, respectively. Aging-induced oxidative hardening enhanced the overall elastic modulus and interfacial constraint effect of the asphalt mixture, thereby improving the stress transfer efficiency among the rubber particles, polyester fibers, and the surrounding matrix. As a result, both the peak load and fracture toughness increased. However, compared with the unaged state, aged asphalt concrete became more susceptible to brittle fracture, with a decrease in fracture energy and a change in the crack propagation path from a curved to a straight trajectory. Full article

Tree mechanical stability is essential for forest management and urban safety. Although static pulling tests are currently the standard for non-destructive advanced risk assessments, these tests have significant methodological limitations. Large trees require high applied forces to produce measurable signals, which poses safety risks and causes equipment wear. Conversely, structurally compromised ancient, veteran, or dead trees (snags) may yield poor signal-to-noise ratios at low loads, leading to unstable model fits and unreliable safety factor extrapolations. Additionally, standard inclinometers often experience interference from motion-induced accelerations. This study introduces a high-resolution, low-noise measurement approach that resolves small basal inclinations and stem bending responses. This method uses laser-based tracking to monitor stem bending, torsion, and inclination under mechanical load. Experimental data were collected by combining traditional pulling tests with this novel system, as well as by conducting a pilot study that monitored tree movement during low-strength wind gusts. The proposed method enables more precise characterization of the initial load-response curve. Improving the signal-to-noise ratio at lower force levels allows for more robust safety extrapolations. When combined with a 3D LiDAR scan, the method can reveal deviations from the theoretical bending line in order to locate internal defects and variations in wood properties. These findings bridge a critical gap in tree risk assessment by improving the applicability of static testing to massive trees, as well as ecologically valuable yet structurally vulnerable snags and ancient and veteran trees. Full article

The focus of this work was to investigate the mechanical properties of additively manufactured (AM) discontinuous carbon fibre-reinforced polymer (DCFRP) composites. Towards the specimen’s fabrication, the Fused Filament Fabrication (FFF) additive manufacturing technique was employed. A number of input printing parameters were varied, such as the infill pattern, infill density, layer height, shell configuration, and raster orientation, in a systematic way. The role of these paraments on the mechanical properties, such as tensile, flexural, and impact strength were investigated. The data was analysed in-depth and the “main effect method” was employed for their comparative ranking. The results of this study showed that tensile and bending strengths were strongly correlated with material content and structural reinforcement. The specimens attained up to 76.7 MPa of tensile strength, while the flexural strength was up to 159.4 MPa, with a deflection of up to 8 mm and 16 mm, respectively. Solid infills, higher densities, finer layer heights, and added shells significantly improved the strength and stiffness. Grid-patterned and low-density specimens caused poor load-bearing capacities, while hexagonal and gyroid infills offered a more balanced performance. Full article

Piezo-enhanced photocatalysis is progressively considered an eco-friendly technology for contaminant removal, harvesting not only solar energy but also mechanical vibrations found in nature. Multiferroic materials present a coupled effect of various properties and can potentially increase the applicability of this process. In this study, Cr- doped bismuth ferrite thin film was deposited on SrTiO₃ substrate by HiPIMS, and its photo-, piezo-, and piezo-photocatalytic efficiencies in Rhodamine B (RhB) degradation were analyzed. The highest removal percentage was found under the simultaneous exposure of visible light and mechanical vibrations, reaching 86.2% after 180 min. The calculated efficiencies for photo- and piezocatalysis were 12.2% and 83.7%, respectively. The rate constant (k) for piezo-photocatalysis was 16.1 times higher than that found during photocatalytic experiments. To assess the contribution of each reactive species to the decomposition process, different reagents were added to the Rhodamine B contaminated solution. The results revealed that when p-benzoquinone was used, the degradation efficiency declined significantly from 86.2% to 37.6%, suggesting that superoxide radicals (O₂^•−) play a key role in decomposing RhB molecules. The structural, chemical, optical, and ferroelectric changes caused by the catalytic processes were analyzed and linked to the proposed degradation mechanisms. The poor photocatalytic efficiency was linked to an improper band structure and an improper polarization orientation of the ferroelectric domains in the as-deposited film. The degradation mechanisms in piezo-photocatalysis were driven partly by the band bending caused by mechanical vibrations and partly by the reorientation of the induced polarization of the domains in the unstrained film. Full article

The production of fiber-reinforced polymer composites using 3D printing technology offers significant potential and opportunities for industrial applications. However, current dimensional limitations in 3D printing necessitate the use of joining techniques to obtain larger components. Recently, innovative strategies such as friction stir spot welding (FSSW) have attracted considerable attention for joining polymer composites due to their ability to produce strong joints with relatively low heat input (solid-state welding). Nevertheless, it is important to understand how the fibers present in fiber-reinforced polymer composites influence material flow and welding performance during the FSSW process. In this study, glass fiber-reinforced polylactic acid (PLA-GF) composite samples produced using a 3D printer were joined by means of FSSW. Five different tool rotational speeds (900, 1200, 1500, 1800, and 2100 rpm) and three different plunge rates (10, 20, and 30 mm/min) were employed during the welding process. Mechanical tests were performed on the welded joints to investigate the relationship between the welding parameters and the resulting mechanical properties. In addition, microstructural analyses were conducted to examine the formation of welding defects. The results revealed that three distinct zones were formed in the material after the FSSW process: the stir zone, mixed zone, and shoulder zone. Defects were observed in the mixed zone of the samples exhibiting relatively lower mechanical properties. The highest tensile force was achieved at a plunge rate of 20 mm/min and a rotational speed of 900 rpm. The highest bending force, on the other hand, was obtained at a plunge rate of 30 mm/min and a tool rotational speed of 2100 rpm. Full article

Honeycomb composites are extensively utilized in critical applications where weight is a concern in a structure, due to their high efficiency in stiffness-to-weight ratio. In this study, the effective elastic orthotropic behavior of honeycomb composites is analytically expressed as a function of the elastic properties of the constituent sheet material and the geometric parameters of the representative unit cell. Closed-form expressions based on classical beam theory and plate theory are evaluated and systematically validated against a high-fidelity finite element analysis FE-based homogenization benchmark constructed from a representative unit cell with in-plane periodic kinematic constraints. The analytical predictions exhibit generally good agreement with the FE results, with plate-theory-based formulations capturing most elastic constants with higher accuracy. To further support the fidelity of the numerical benchmark, the predicted normalized in-plane moduli are additionally compared with published experimental measurements for aluminum honeycombs, demonstrating close agreement for representative specimens. To quantify the influence of the geometric parameters, a Taguchi-style design-of-experiments (DOE) study reveals that relative density and internal cell angle jointly govern the majority of elastic moduli and Poisson’s ratios, while cell height plays a minor role. Furthermore, dedicated parametric studies confirm the cubic thickness-scaling of in-plane moduli (E₁, E₂, G₁₂), demonstrating the dominant role of bending-controlled deformation. Together, these results establish a validated, high-fidelity FE homogenization benchmark for assessing analytical formulations and providing design-level constitutive data for optimizing honeycomb core sandwich structures. Full article

Polypropylene (PP) biocomposites reinforced with Cornus sanguinea L. (CS) pruning-waste particles were investigated using a combined experimental mechanics and finite element (FE) validation framework to support model-based design with an under-utilized lignocellulosic feedstock. Two particle-size fractions (<100 µm, LF1; 100–250 µm, LF2) were produced by grinding and sieving and incorporated into PP at 5–20 wt% via melt compounding and compression molding. Tensile and three-point bending properties were measured in accordance with ASTM D638 and ASTM D790. PP exhibited a tensile strength of 23.63 ± 0.51 MPa and a tensile modulus of 868 ± 21 MPa. Incorporation of LF1 particles increased tensile modulus monotonically, reaching 1020 ± 137 MPa at 20 wt%, while tensile strength decreased with filler content; by contrast, the 20 wt% LF2 formulation showed a pronounced strength reduction to 16.30 ± 0.25 MPa, indicating a disadvantageous size–loading interaction. In flexure, strength was comparatively insensitive to reinforcement (PP: 39.5 ± 0.34 MPa; reductions typically ≤7%), whereas flexural modulus increased to 2152 ± 27 MPa (LF1) and 2110 ± 34 MPa (LF2). FE models calibrated using true stress–true plastic strain data accurately reproduced tensile responses across the full strain range and flexural behavior within the pre-contact-dominated regime, demonstrating the suitability of PP/CS biocomposites for stiffness-driven applications. Full article

Engineered wood products manufactured with the durability and density of a Pinus radiata D. Don species usually do not achieve the mechanical properties of a structural material for construction; hence, the reinforcement of this kind of product is recommended, but the use of commonly used hazardous adhesives is a problem. Therefore, the primary objective of this research was to investigate the enhancement of various properties of glulam beams made from radiata pine through the application of a high-performance reinforcing composite, based on carbon fiber, polyvinyl alcohol, and other nanomaterials, at a laboratory scale. For this purpose, thermal and mechanical tests were performed in different composite formulations to choose the best ones and to manufacture the glulam beams, in which bending properties were measured. Based on the results, the samples reinforced with graphene stood out, and the samples mixed with epoxy resin presented statistically the same values of flexural stiffness and strength as the control samples elaborated with commercial wood adhesives. It is also important to highlight the performance of the samples M7 (PVA (7.5%) + NL (0.01%) + GP (0.01%) + NSiO₂ (0.01%)) and M8 (PVA (7.5%) + NL (0.01%) + GP (0.01%) + NTiO₂ (0.01%)), which are not mixed with epoxy resin and showed statistically the same flexural performance as epoxy resin, in terms of maximum load and displacement. As a conclusion, it could be said that this new high-performance composite could be a comparable alternative to hazardous commercial adhesives, by obtaining lower values, but close to those of the control sample, which are the most used when reinforcing wood products with engineering fibers. Full article

Self-sensing refers to structural material sensing by auxiliary devices without intelligent features. The analysis of the electrical parameters of a single carbon fiber is the foundation of CFRP self-sensing. Focusing on electrical-resistance-based strain, this study conducts a theoretical analysis of the electrical parameters of a single carbon fiber. The relationship between stress-induced strain and resistance is established, yielding the gage factor (GF) under the load effect. Drawing upon the impurity scattering mechanism, the relationship between thermal-induced strain and resistance is formulated, leading to the GF under thermal effects. According to the quasi-static equivalent superposition principle, strain vs. resistance in the effect of thermal–mechanical coupling was established, and a GF model is proposed. The analysis of a single carbon fiber demonstrates that under load effect the contribution of the piezoresistive effect reaches 13.4%, which is non-negligible. Thermal-resistance tests were conducted on a single carbon fiber with different initial states. The thermal-resistance analysis indicated that the resistance of a single carbon fiber decreased with an increase in temperature. The initial state had a significant impact on the GF. The thermal resistance of a free single carbon fiber can be expressed by two types of models, each with an error of less than 0.2% from 223 K to 473 K. Based on four-point bending specimens, the force-resistance test of a single carbon fiber was conducted indirectly. The improvement in the production process has led to an increase in the graphitization degree of carbon fibers. The $K_{\mathrm{S}}^{\mathrm{F}}$ values of A3 and B3 are 1.411 and 1.405, respectively, both of which are higher than those of carbon fibers in the earlier literature. The strain-resistance analysis showed that the stress-induced GF of a single carbon fiber is lower than the thermal-induced GF. When the deformation was constrained, the stress-induced GF of the single carbon fiber was reduced. Together, the thermal and mechanical properties of a single carbon fiber make it more suitable as a temperature sensor than as a damage sensor. Full article

Preparing a highly wear-resistant AlTiN coating on a powder metallurgy (PM) M42 high-speed steel substrate is a key strategy to enhance tool performance and meet the demands of efficient machining. This study adopted a process route comprising substrate preparation, heat treatment regulation, and arc-PVD deposition of AlTiN coatings to systematically investigate the influence of sintering temperature (1130, 1160, and 1190 °C) and austenitizing time (1150 °C for 0, 15, 60, and 120 min) on the microstructure and mechanical properties of the substrate, as well as on the tribological performance of the AlTiN coatings. The results indicate that elevating the sintering temperature promotes densification of the matrix, with Vickers hardness increasing from 366 HV to 462 HV and bending strength (σ) increasing from 1064 MPa to 1310 MPa. The predominant carbide phases identified are MC, M₂C, and M₆C. During austenitizing, microstructural changes consistent with a progressive transformation from M₂C to MC and M₆C carbides were indicated by SEM and XRD analyses. Precipitation strengthening was most evident after 60 min, with hardness reaching 868 HV. In contrast, bending strength (σ) exhibited a progressive decline with increasing austenitizing time, decreasing from 1310 MPa to 1015 MPa after 120 min, illustrating a clear trade-off between hardness and toughness. The wear behavior of the coating is governed synergistically by substrate hardness, bending strength (σ), coating–substrate interfacial adhesion strength (L_C), and carbide phase transformation. Elevated substrate hardness enhances anti-wear performance; bending strength influences crack propagation and spallation tendency; and L_C determines the efficiency of interfacial load transfer. The carbide phase evolution appears to modulate the coating’s wear behavior by regulating both the microstructure and mechanical properties of the substrate. Among the six sample conditions evaluated, the A3 sample (sintered at 1190 °C and austenitized for 120 min) exhibited the lowest wear rate (2.38 × 10⁻⁶ mm³·N⁻¹·m⁻¹), demonstrating superior wear resistance. These findings provide a reference for process optimization and rational design of M42/AlTiN composite coating systems. Full article

This study investigates the synergistic effects of combining polyphosphoric acid (PPA) and styrene–butadiene–styrene (SBS) as modifiers in asphalt binders to enhance their performance. The research focuses on optimizing the concentrations of PPA and SBS to improve the resistance to permanent deformation, cracking at intermediate and low temperatures, and resistance to aging. A series of empirical and rheological tests, including penetration, softening point, elastic recovery, dynamic shear rheometer (DSR), multiple stress creep recovery (MSCR), and bending beam rheometer (BBR), were conducted to evaluate the rheological and engineering properties of the modified binders. The results indicate that PPA can partially replace SBS, offering comparable improvements in high-temperature performance and creep resistance. The MSCR test revealed a statistically significant synergistic effect between PPA and SBS, resulting in improved recovery and reduced non-recoverable compliance. However, PPA alone shows limited effectiveness at low temperatures and in properties that are governed by elastic response. This study highlights the potential for optimizing asphalt modifiers by leveraging the complementary properties of PPA and SBS in hybrid systems, particularly regarding high-temperature properties and dynamic loading. Full article

Background: The combination of pharmacological therapy and exercise is frequently recommended for osteoporosis management; however, whether antiresorptive agents may interfere with exercise-induced bone adaptation remains unclear. This study aimed to investigate the independent and combined effects of zoledronate and treadmill exercise on bone microarchitecture and mechanical strength in an ovariectomized rat model. Methods: Twenty-four female Sprague Dawley rats underwent ovariectomy and were assigned to four groups: Control, zoledronate (ZA), treadmill exercise (T), and combined zoledronate and exercise (ZA + T). An additional sham-operated group was included. Zoledronate was administered as a single subcutaneous injection, and a 6-week treadmill exercise routine was implemented. Bone microarchitecture was assessed using micro-computed tomography, and a three-point bending test was employed for evaluation of mechanical properties. Results: The combined ZA + T group demonstrated significant improvements in trabecular bone parameters, including bone volume/tissue volume and trabecular number, compared with the Control group. Mechanical strength parameters, including maximum load and stiffness, were also significantly enhanced in the ZA + T group. Cortical bone parameters exhibited no significant changes. Conclusions: Treadmill exercise did not attenuate the effects of zoledronate, and may offer additive benefits in enhancing trabecular bone microarchitecture and mechanical strength. These findings suggest that exercise therapy can complement bisphosphonate treatment and contribute to optimizing therapeutic strategies for osteoporosis, supporting the potential utility of combined pharmacological and exercise-based interventions for improving bone health. Full article

Barley lodging—specifically stem lodging—occurs when the bending moments from wind and ear weight exceed the culm’s load-bearing capacity. Lodging risk decreases as plant height decreases and culm strength increases. Geometry (stem diameter, culm wall thickness) and material strength determine culm bending strength. By studying changes in stem mechanical properties (at three positions along the culm) in two genotypes (grown in a greenhouse), we found that culm strength (assessed with a three-point bending test) slightly diminished through ripening owing to a decline in both area moment of inertia (i.e., strength due to geometry alone) and apparent material strength, presumably due to turgor loss. When the stem segments collected from fully ripe plants were dried to a moisture content typical of harvest maturity, however, strength rose to a maximum. Thus, minimum stem bending resistance occurs during a window in which plants are fully ripe but have not yet reached harvest-dry moisture content. Hence, in the absence of rain—which would severely reduce the mechanical strength of dry, ripe plants—the physiological risk of stem lodging is highest when the crop is fully ripe but not yet harvest-dry. However, the actual lodging risk increases as harvest approaches, because summer storms are frequent at this time of year and dry straw loses rigidity when wetted. Full article

Fatigue failure in scaffolding components poses significant risks to worker safety, particularly in high-altitude construction environments. This study investigates the fatigue behavior of scaffolding stirrups, a critical structural element prone to premature failure. The objective is to analyze the fatigue damage mechanisms in stirrups through a combined experimental and numerical approach. Mechanical characterization and micro-hardness testing were conducted to assess the material properties of the stirrup, while finite element modeling (FEM) was employed to simulate its performance under cyclic loading. The Johnson–Cook material model was utilized to compare experimental hysteresis curves with FEM results, validating the numerical approach. Additionally, the Extended Finite Element Method (XFEM) was applied to model crack initiation and propagation. Results reveal that material hardening and fatigue crack growth are the primary causes of stirrup failure, with distinct fatigue zones and crack paths identified. The study quantifies the relationship between crack growth stages and stirrup bending, providing insights into the failure process. These findings contribute to improving the safety and lifespan of scaffolding systems by identifying key factors influencing stirrup durability. Full article

This study addresses several key limitations identified in previous research on additively manufactured PLA composites. Unlike most earlier studies that focused primarily on the characterization of as-printed materials, the present work systematically investigates both mechanical and surface behavior before, during, and after artificial aging. In addition, six different printing configurations and reinforcement types (PVC and fiberglass mesh) were analyzed under controlled conditions, enabling a more reliable assessment of their combined influence on composite performance. Printed specimens were artificially aged for 45 and 90 days. The aging protocol combined cyclic changes in moisture, temperature, UV, and IR agents, trying to mimic real exploitation conditions as realistically as possible. The chemical and surface changes during aging were tracked using FTIR spectroscopy, colorimetry, contact angle, and surface free energy measurements. Mechanical performance at 0, 45, and 90 days was evaluated through tensile, three-point bending, and Charpy impact tests, as well as full-scale cantilever loading tests of real printed drone arms. Results show that artificial aging causes measurable chemical and surface modifications, as indicated by changes in the FTIR degradation index and surface wettability. However, these changes do not result in severe mechanical degradation within the investigated aging period. Reinforcement in the form of incorporated PVC and fiberglass mesh significantly affected failure behavior. Specimens printed with higher infill density and thicker infill lines generally exhibit improved mechanical properties. Specimens stiffness and impact resistance were also altered. Results demonstrate that reinforced PLA structures are suitable for lightweight drone applications. Full article