Search Results (115)

Aligned CS/Rx aerogels were fabricated by inducing non-directional ice growth (freeze-molding) followed by low-temperature curing, resulting in monoliths with interconnected channels, a high void fraction, and moldability. The swelling index (S%) was calculated to be 1029, the apparent density 0.496 g·cm⁻³, and the estimated porosity 90% based on micrographic analysis. Aerogels have mechanical behavior Shore A hardness greater than 25. Batch metal removal tests were performed (10 mL, 100 mg·L⁻¹ Cr(VI), 0.19 g adsorbent, 24 h, and pH 5–5.5), and the material achieved 95% metal removal. Additional kinetic and isothermal results were obtained using CS85R15 on a packed column (20 to 140 mg·L⁻¹, 1000 mL Cr(VI), 0.80 g adsorbent, 24 h, and pH 5–5.5). Equilibrium data were consistent with a heterogeneous surface hosting a specific site, as reflected in the joint Freundlich/Langmuir fit (q_max 100.8 mg·g⁻¹ for Langmuir). This confirmed the preservation of chitosan functionalities (–OH/–NH) after processing, while XPS detected chromium on the surface with signals consistent with the partial reduction of Cr(VI) to Cr(III) on the aerogel surface. This highlights the relevance of adsorption-based technologies for water remediation, where high-porosity and low-density materials allow for short diffusion pathways and capture electrostatics by protonated amines and redox conversion of hazardous substances. The soft-cure freeze-molding technique is simple, scalable, and compatible with packed-bed/column operation, providing a material platform for tailoring the microstructure (sheets and channels) and surface chemistry to regenerable sorbents for industrial wastewater treatment. Full article

In the recent years, several studies from developing economies have reported the presence of per- and polyfluoroalkyl substances (PFAS) in water bodies, with perfluorooctanoic acid (PFOA) predominating, a potential endocrine disruptor. In this study, an engineered sugarcane bagasse biochar–chitosan composite (SBCT) was designed, synthesized, and evaluated as a novel adsorbent for the removal of PFOA from aqueous systems at concentrations up to 500 ppb. Batch adsorption experiments were conducted to investigate the effects of initial PFOA concentration, contact time, pH, adsorbent dosage, and temperature. Scanning electron microscopy (SEM) showed that SBCT has a significant porous structure. The composite showed over 90% of PFOA removal from water. Further, peaks corresponding to C–F bonds observed after adsorption by Fourier transform infrared (FTIR) spectroscopy confirms the adsorption of PFOA on SBCT. The protonated amine groups (NH₃⁺) in chitosan enhanced the adsorption of anionic PFOA through electrostatic attraction with carboxyl groups (COO⁻). The kinetic study revealed that pseudo-first-order best described the adsorption process, with an equilibrium adsorption capacity (q_eq) of 2.78 mg/g, suggesting that physisorption is the predominant mechanism. The Langmuir Isotherm model gave the best fit, establishing a maximum adsorption capacity (q_max) of 9.08 mg/g. Thermodynamic analysis revealed that the adsorption process was spontaneous and exothermic, consistent with physisorption. The regeneration capacity of the SBCT composite demonstrated exceptional reusability over five methanol adsorption–desorption cycles. The adsorption kinetics, equilibrium behavior, and regeneration efficiency suggest that SBCT is a viable low-cost adsorbent for batch adsorption-based treatment systems targeting PFOA removal, particularly in decentralized and resource-constrained water treatment applications. Full article

Ethanolamine (EA) is a widely used yet toxic volatile organic compound (VOC). However, existing gas sensors for EA detection face persistent challenges in achieving exceptional sensitivity and low detection limits at room temperature (RT). In this study, a novel and high-performance EA sensor based on the MoO₃/BiOI composite was prefabricated using hydrothermal and cyclic impregnation methods. The response value toward 100 ppm EA reached 861.3, which was 3.5-times higher compared to that of pure MoO₃. In addition, the MoO₃/BiOI composite exhibited a low detection limit (0.13 ppm), excellent selectivity, short response/recovery times, exceptional repeatability and long-term stability. The outstanding gas sensing performance of the MoO₃/BiOI is attributed to the formation of a p-n heterojunction, synergistic effects between the two materials, abundant adsorbed oxygen species and superior charge transfer efficiency. The sensor developed in this work effectively addresses the long-standing challenges, demonstrating unprecedented practical application potential for EA gas detection. Simultaneously, this study provides a novel strategy, a new approach and a promising material for the subsequent development of advanced amine sensors. Full article

Developing sustainable and molecularly selective adsorbents for heavy-metal removal remains a critical challenge in water purification. Herein, we report a green molecular-engineering approach for fabricating aza-crown ether functionalized sodium alginate aerogels (ACSA) capable of highly selective Cu²⁺ capture. The aerogels were synthesized via saccharide-ring oxidation, Cu²⁺-templated self-assembly, and reductive amination, enabling the covalent integration of aza-crown ether motifs within a hierarchically porous biopolymer matrix. Structural analyses (FTIR, ¹³C NMR, XPS, SEM, TGA) confirmed the in situ formation of macrocyclic N/O coordination sites. Owing to their interconnected porosity and chemically stable framework, ACSA exhibited rapid sorption kinetics following a pseudo-second-order model (R² = 0.999) and a Langmuir maximum adsorption capacity of 150.82 mg·g⁻¹. The material displayed remarkable Cu²⁺ selectivity over Zn²⁺, Cd²⁺, and Ni²⁺, arising from the precise alignment between Cu²⁺ ionic radius (0.73 Å) and crown-cavity dimensions, synergistic N/O chelation, and Jahn-Teller stabilization. Over four regeneration cycles, ACSA retained more than 80% of its original adsorption capacity, confirming excellent durability and reusability. This saccharide-ring modification strategy eliminates crown-ether leaching and weak anchoring, offering a scalable and environmentally benign route to bio-based adsorbents that combine molecular recognition with structural stability for efficient Cu²⁺ remediation and beyond. Full article

A novel mesoporous spherical chelating lignin-based adsorbent was successfully synthesized via inverse suspension polymerization using sulfate pine pulping black liquor as raw material, followed by graft copolymerization with acrylonitrile and subsequent amination. The obtained aminated cyanoethyl spherical lignin resin (ACSLR) exhibited a well-defined porous morphology and abundant active sites, as confirmed by SEM and FT-IR. Adsorption experiments demonstrated high Pb²⁺ uptake capacity (63.98 mg·g⁻¹) under optimal conditions (pH = 5.5, 2.0 g·L⁻¹ adsorbent dosage, and 150 mg·L⁻¹ initial concentration of Pb²⁺ solution). The adsorption process followed the Langmuir isotherm and pseudo-second-order kinetics, indicating monolayer chemisorption dominated by amino and cyano groups. This work provides a sustainable strategy for valorizing industrial lignin waste into efficient adsorbents for heavy metal removal, highlighting its potential for practical wastewater treatment applications. Full article

Carbon capture plays a crucial role in mitigating carbon emissions, which is essential for curbing global warming. Owing to its benefits, such as the absence of secondary pollution, operational simplicity, and low energy consumption, adsorption has been widely used in carbon capture. Accordingly, the design of high-efficiency adsorption materials is critical to achieving superior carbon capture performance. In this review, we systemically outline the adsorption mechanisms, influencing factors, and various adsorption materials, including porous carbon-based material, zeolites, metal–organic frameworks (MOFs), solid amines, and emerging adsorbents (porous liquids and supported ionic liquid phase), along with their recent research progress in carbon capture. Furthermore, we point out the design strategies for enhancing CO₂ capture performance and potential research directions in the future. Full article

Carbon dioxide (CO₂) is the most significant anthropogenic greenhouse gas (GHG), accounting for approximately 81% of total emissions, with methane (CH₄), nitrous oxide (N₂O), and fluorinated gases contributing the remainder. Rising atmospheric CO₂ concentrations, driven primarily by fossil fuel combustion, industrial processes, and transportation, have surpassed the Earth’s natural sequestration capacity, intensifying climate change impacts. Carbon Capture, Utilization, and Storage (CCUS) offers a portfolio of solutions to mitigate these emissions, encompassing pre-combustion, post-combustion, oxy-fuel combustion, and direct air capture (DAC) technologies. This review synthesizes advancements in CO₂ capture materials including liquid absorbents (amines, amino acids, ionic liquids, hydroxides/carbonates), solid adsorbents (metal–organic frameworks, zeolites, carbon-based materials, metal oxides), hybrid sorbents, and emerging hydrogel-based systems and their integration with utilization and storage routes. Special emphasis is given to CO₂ mineralization using mine tailings, steel slag, fly ash, and bauxite residue, as well as biological mineralization employing carbonic anhydrase (CA) immobilized in hydrogels. The techno-economic performance of these pathways is compared, highlighting that while high-capacity sorbents offer scalability, hydrogels and biomineralization excel in low-temperature regeneration and integration with waste valorization. Challenges remain in cost reduction, material stability under industrial flue gas conditions, and integration with renewable energy systems. The review concludes that hybrid, cross-technology CCUS configurations combining complementary capture, utilization, and storage strategies will be essential to meeting 2030 and 2050 climate targets. Full article

Mercury (Hg²⁺) contamination in water systems poses a severe environmental and health hazard due to its high toxicity and bioaccumulation potential. In this study, a novel adsorbent was developed by sequentially modifying kaolin via acid–base treatment, titanium dioxide (TiO₂) incorporation, and 3-aminopropyltriethoxysilane (APTES) grafting. Batch adsorption experiments revealed that the fully modified kaolin (TiO₂-loaded and APTES grafted) exhibited the highest adsorption capacity (25.6 mg/g) compared to the acid–base-treated (5.8 mg/g) and TiO₂-loaded (17.7 mg/g) kaolin. Under optimal conditions (75 mg adsorbent dosage; 70 mg/L Hg²⁺; pH 5), the fully modified kaolin maintained its performance even in the presence of varying ionic strengths, natural organic matter, and competing metal ions. Adsorption kinetics followed a pseudo-second-order model, and the equilibrium data were well fitted by the Langmuir isotherm. Antibacterial activity assay revealed that the TiO₂-loaded kaolin effectively inhibited S. aureus (minimum inhibitory concentration = 2.5 mg/mL) and showed moderate activity against E. coli (BL21) (minimum inhibitory concentration = 5 mg/mL). However, antibacterial activity decreased after amine functionalization, indicating a compromise between enhancing adsorption capacity and preserving antibacterial functionality. This study presents a promising cost-efficient approach for the simultaneous removal of Hg²⁺ ions from water matrices and inhibiting bacterial growth, aligning with SDG 6 (Clean Water and Sanitation). Full article

The exploit of an efficient method for uranium (U) extraction is crucial for the development of nuclear energy. In this study, an aminated lignin-based microsphere (AL-PEI/GMS) was synthesized and used as an adsorbent for the recovery of hexavalent uranium (U(VI)) from salt-lake brine. The effects of adsorbent dosage, initial solution pH value, interfering ions, adsorption time, and temperature on the U(VI) adsorption performance of AL-PEI/GMSs were systematically investigated. The results show that when the adsorbent dosage was 2 g/L, the temperature was 45 °C, and the pH was 8, the adsorption capacity of AL-PEI/GMS for U(VI) could reach 256.4 mg/g. In addition, after five cycles, a high U(VI) adsorption efficiency of over 90% could still be achieved. Furthermore, through a fixed-bed system, AL-PEI/GMS could rapidly adsorb U(VI) from actual salt-lake brine. Therefore, the prepared AL-PEI/GMS is a competitive alternative material compared with other adsorbents in terms of efficiently recovering U(VI) from actual salt-lake brine. Full article

Waste materials have emerged as attractive low-cost feedstocks for adsorbent development in environmental remediation and materials engineering. Organic wastes are particularly rich in cellulose, hemicellulose, lignin, and pectin, which provide reactive oxygenated groups such as hydroxyls and carboxyls. While inorganic wastes offer stability, lower water retention makes them promising candidates. This study explores the functionalization of waste-derived organic and inorganic matrices using two amine-based agents: 3-aminopropyltrimethoxysilane (APTMS) and polyethylenimine (PEI). The materials were categorized as organic (orange peel, corn cob) or inorganic (silica gel, eggshell) and subjected to a pretreatment process involving drying, grinding, and sieving; inorganic substrates additionally underwent acid activation with citric acid. Surface modification was carried out in ethanolic (APTMS) or aqueous (PEI) media. To assess their suitability and processability as particulate sorbents, drying kinetics, physicochemical properties (FTIR, ζ-potential, pH, conductivity, Boehm titration), and flow characteristics (Carr and Hausner indices) were evaluated. The findings enable a comparative analysis of the functionalization efficiency and elucidate the relationship between substrate type (organic vs. inorganic) and its performance as a modified adsorbent. This approach advances the development of novel sorbent matrices for greenhouse gas mitigation while reinforcing circular economy principles through the valorization of low-cost, readily available waste materials. Full article

The presence of impurities Fe and trace radioactive U in rare earth elements (REEs) may lead to a significant decline in the performance of high-purity rare earth products. For deep removal from REEs in a green and efficient way, an amine-functionalized silica-based adsorbent, TNDA/SiO₂-P, was prepared by a simple vacuum impregnation method, which had a high organic loading rate of 31.2 wt.%. The experimental results showed that it exhibited good adsorption selectivity for uranium and iron, with separation factors SF_U/REE = 20147 and SF_Fe/REE = 88128 in 5 M HCl. The adsorption kinetics was fast, with equilibrium obtained in 120 min. The 0.1 M HCl can desorb U and Fe efficiently. The deep removal of U and Fe from REEs including Sc can be achieved through chromatographic column separation with high enrichment. FT-IR, XPS and DFT calculations mutually confirmed that protonated TNDA/SiO₂-P exhibited a selective mechanism for uranium and iron in complex anion species in the hydrochloric acid system. This demonstrates its potential for efficiently removing trace impurities U and Fe from REEs. Full article

Environmental contamination is a critical global concern, primarily due to detrimental greenhouse gas (GHG) emissions, especially carbon dioxide (CO₂), which significantly contribute to climate change. Moreover, the presence of harmful heavy metals like Ni, Cd, Cu, Hg, and Pb in soil and water ecosystems has led to poor water quality. Noble metal nanoparticles (MNPs), for instance, Pd, Ag, Pt, and Au, have emerged as promising solutions for addressing environmental pollution. However, the practical utilization of MNPs faces challenges as they tend to aggregate and lose stability. To overcome this issue, the reverse double-solvent method (RDSM) was utilized to synthesis melamine-based porous polyaminals (POPs) as a supportive material for the in situ growing of silver nanoparticles (Ag NPs). The porous structure of melamine-based porous polyaminals, featuring aminal-linked (-HN-C-NH-) and triazine groups, provides excellent binding sites for capturing Ag⁺ ions, thereby improving the dispersion and stability of the nanoparticles. The resulting material exhibited ultrafine particle sizes for Ag NPs, and the incorporation of Ag NPs within the porous polyaminals demonstrated a high surface area (~279 m²/g) and total pore volume (1.21 cm³/g), encompassing micropores and mesopores. Additionally, the Ag NPs@POPs showcased significant capacity for CO₂ capture (2.99 mmol/g at 273 K and 1 bar) and effectively removed Cu (II), with a remarkable removal efficiency of 99.04%. The nitrogen-rich porous polyaminals offer promising prospects for immobilizing and encapsulating Ag nanoparticles, making them outstanding adsorbents for selectively capturing carbon dioxide and removing metal ions. Pursuing this approach holds immense potential for various environmental applications. Full article

This study developed a novel adsorbent for Cr (VI) removal from wastewater by grafting N-[(dimethylamino)methylene]thiourea (TUFA) onto lignin. The resulting TUFA-functionalized lignin adsorbent AL was comprehensively characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR), and X-ray photoelectron spectroscopy (XPS). Batch adsorption experiments systematically evaluated the influence of solution pH, contact time, temperature, initial Cr (VI) concentration, and adsorbent dosage. AL exhibited high adsorption capacity (593.9 mg g⁻¹ at 40 °C), attributed to its abundant nitrogen and sulfur-containing functional groups. Kinetic analysis revealed that the adsorption process followed pseudo-second-order kinetics. Equilibrium isotherm data were best described by the Langmuir model, indicating predominant monolayer chemisorption. Thermodynamic parameters demonstrated that Cr (VI) adsorption onto AL is spontaneous, endothermic, and entropy-driven. The adsorption mechanism involves membrane diffusion and intra-particle diffusion processes. This work successfully synthesized a stable, effective, and low-cost adsorbent (AL) using an amine agent incorporating both nitrogen and sulfur functional groups, offering a promising approach for treating Cr (VI)-contaminated wastewater. Full article

This work evaluates the CO₂-adsorption relevance and cycling stability of graphene oxide–silica (GO-SiO₂) and reduced graphene oxide–silica (rGO-SiO₂) gels after amine functionalization, demonstrating high-capacity retention under repeated adsorption–desorption cycles: rGO-SiO₂-APTMS retains ≈96.3% of its initial uptake after 50 cycles, while GO-SiO₂-APTMS retains ≈90.0%. The use of surfactants to control the organization of inorganic and organic molecules has enabled the development of ordered mesostructures, such as mesoporous silica and organic/inorganic nanocomposites. Owing to the outstanding properties of graphene and its derivatives, synthesizing mesostructures intercalated between graphene sheets offers nanocomposites with novel morphologies and enhanced functionalities. In this study, GO-SiO₂ and rGO-SiO₂ gels were synthesized and characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TG), mass spectrometry (MS), N₂ adsorption–desorption isotherms, and transmission electron microscopy (TEM). The resulting materials exhibit a laminar architecture, with mesoporous silica domains grown between graphene-based layers; the silica contents are 83.6% and 87.6%, and the specific surface areas reach 446 and 710 m²·g⁻¹, respectively. The laminar architecture is retained regardless of the surfactant-removal route; however, in GO-SiO₂ obtained by solvent extraction, a fraction of the surfactant remains partially trapped. Together with their high surface area, hierarchical porosity, and amenability to surface functionalization, these features establish amine-grafted graphene–silica gels, particularly rGO-SiO₂-APTMS, as promising CO₂-capture adsorbents. Full article

Direct air capture (DAC), as a complementary strategy to carbon capture and storage (CCS), offers a scalable and sustainable pathway to remove CO₂ directly from the ambient air. This study presents a detailed evaluation of the amine-functionalised metal-organic framework (MOF) sorbent, mmen-Mg₂(dobpdc), for DAC using a temperature–vacuum swing adsorption (TVSA) process. While this sorbent has demonstrated promising performance in point-source CO₂ capture, this is the first dynamic simulation-based study to rigorously assess its effectiveness for low-concentration atmospheric CO₂ removal. A transient one-dimensional TVSA model was developed in Aspen Adsorption and validated against experimental breakthrough data to ensure accuracy in capturing both the sharp and gradual adsorption kinetics. To enhance process efficiency and sustainability, this work provides a comprehensive parametric analysis of key operational factors, including air flow rate, temperature, adsorption/desorption durations, vacuum pressure, and heat exchanger temperature, on process performance, including CO₂ purity, recovery, productivity, and specific energy consumption. Under optimal conditions for this sorbent (vacuum pressure lower than 0.15 bar and feed temperature below 15 °C), the TVSA process achieved ~98% CO₂ purity, recovery over 70%, and specific energy consumption of about 3.5 MJ/KgCO₂. These findings demonstrate that mmen-Mg₂(dobpdc) can achieve performance comparable to benchmark DAC sorbents in terms of CO₂ purity and recovery, underscoring its potential for scalable DAC applications. This work advances the development of energy-efficient carbon removal technologies and highlights the value of step-shape isotherm adsorbents in supporting global carbon-neutrality goals. Full article