Search Results (37)

To improve the efficiency and stability of the system, this paper proposes a monolithic integrated optical path design for a cavity optomechanical accelerometer based on a 250 nm top silicon thickness silicon-on-insulator (SOI) wafer instead of readout through U-shape fiber coupling. Finite Element Analysis (FEA) and Finite-Difference Time-Domain (FDTD) methods are employed to systematically investigate the performance of key optical structures, including the resonant modes and bandgap characteristics of photonic crystal (PhC) microcavities, transmission loss of strip waveguides, coupling efficiency of tapered-lensed fiber-to-waveguide end-faces, coupling characteristics between strip waveguides and PhC waveguides, and the coupling mechanism between PhC waveguides and microcavities. Simulation results demonstrate that the designed PhC microcavity achieves a quality factor (Q-factor) of 2.26 × 10⁵ at a 1550 nm wavelength while the optimized strip waveguide exhibits a low loss of merely 0.2 dB over a 5000 μm transmission length. The strip waveguide to PhC waveguide coupling achieves 92% transmittance at the resonant frequency, corresponding to a loss below 0.4 dB. The optimized edge coupling structure exhibits a transmittance of 75.8% (loss < 1.2 dB), with a 30 μm coupling length scheme (60% transmittance, ~2.2 dB loss) ultimately selected based on process feasibility trade-offs. The total optical path system loss (input to output) is 5.4 dB. The paper confirms that the PhC waveguide–microcavity evanescent coupling method can effectively excite the target cavity mode, ensuring optomechanical coupling efficiency for the accelerometer. This research provides theoretical foundations and design guidelines for the fabrication of high-precision monolithic integrated cavity optomechanical accelerometers. Full article

To enable accurate evaluation of satellite laser communication terminals under solar outage interference, this paper presents the design and implementation of a solar radiation simulation system targeting the 1540–1560 nm communication band. The system reconstructs co-propagating interference conditions through standardized and continuously tunable output, based on high irradiance and spectral uniformity. A compound beam homogenization structure—combining a multimode fiber and an apodizator—achieves 85.8% far-field uniformity over a 200 mm aperture. A power–spectrum co-optimization strategy is introduced for filter design, achieving a spectral matching degree of 78%. The system supports a tunable output from 2.5 to 130 mW with a 50× dynamic range and maintains power control accuracy within ±0.9%. To suppress internal background interference, a BRDF-based optical scattering model is established to trace primary and secondary stray light paths. Simulation results show that by maintaining the surface roughness of key mirrors below 2 nm and incorporating a U-shaped reflective light trap, stray light levels can be reduced to 5.13 × 10⁻¹² W, ensuring stable detection of a 10⁻¹⁰ W signal at a 10:1 signal-to-background ratio. Experimental validation confirms that the system can faithfully reproduce solar outage conditions within a ±3° field of view, achieving consistent performance in spectrum shaping, irradiance uniformity, and background suppression. The proposed platform provides a standardized and practical testbed for ground-based anti-interference assessment of optical communication terminals. Full article

This paper proposes a high-sensitivity U-shaped optical fiber sensor based on indium tin oxide (ITO) for surface plasmon resonance (SPR) sensing. Finite element simulations reveal that introducing ITO enhances the surface electric field strength by 1.15× compared to conventional designs, directly boosting sensitivity. The U-shaped structure optimizes evanescent wave–metal film interaction, further improving performance. In an external refractive index (RI) range of 1.334–1.374 RIU, the sensor achieves a sensitivity of 4333 nm/RIU (1.85× higher than traditional fiber sensors) and a figure of merit (FOM) of 21.7 RIU⁻¹ (1.68× improvement). Repeatability tests show a low relative standard deviation (RSD) of 0.4236% for RI measurements, with a maximum error of 0.00018 RIU, confirming excellent stability. The ITO coating’s strong adhesion ensures long-term reliability. With its simple structure, ease of fabrication, and superior sensitivity/FOM, this SPR sensor is well-suited for high-precision biochemical detection in intelligent sensing systems. Full article

Aflatoxin M1 (AFM1) appears in the milk of animals that have consumed feed contaminated with aflatoxin B1. AFM1 presence in milk is regulated by the European Commission, which has set the maximum allowable limits for adult and infant consumption to 50 and 25 pg/mL, respectively. Here, a rapid and sensitive method for detecting AFM1 in milk based on an immersible silicon photonic chip is presented. The chip features two U-shaped silicon nitride waveguides formed as Mach–Zehnder interferometers. One interferometer is functionalized with AFM1–bovine serum albumin conjugate and the other with BSA to serve as a blank. The chip is connected to a broad-band white LED and a spectrophotometer by a bifurcated optical fiber and an assay is performed by immersing the chip in a mixture of milk with the anti-AFM1 antibody. Then, the chip is sequentially immersed in biotinylated anti-rabbit IgG antibody and streptavidin solutions for signal enhancement. The assay is completed in 20 min and the detection limit for AFM1 in undiluted milk is 20 pg/mL. Given its analytical performance and the absence of pumps and fluidics that lead to a compact instrument design, the proposed immunosensor is ideal for the on-site detection of AFM1 in milk samples. Full article

Fiber optic sensors have gained popularity over the last few decades. This is due to their numerous advantages, such as good metrological parameters, biocompatibility and resistance to magnetic and electric fields and environmental pollution. However, those built from glass fiber have one main disadvantage—they are fragile, meaning they can be easily damaged, even by the presence of vibration. Due to the great progress made by material research recently, it is possible to build such a sensor with polymer fibers instead. Although those fibers have worse transmission parameters compared to telecommunication fibers, they provide the possibility to realize flexible fiber optic sensors. Taking into consideration other advantages of such fibers, including biocompatibility, electromagnetic resistance and even, biodegradation characteristics, as well as there being a variety of materials we can use, it can be seen that those materials are beneficial to produce fiber optic sensors. This paper aims to provide researchers with guidelines on the factors to consider when choosing a material for bent fiber optic sensors, depending on the application. Full article

Conventional methods for pathogen detection in water rely on time-consuming enrichment steps followed by biochemical identification strategies, which require assay times ranging from 24 hours to a week. However, in recent years, significant efforts have been made to develop biosensing technologies enabling rapid and close-to-real-time detection of waterborne pathogens. In previous studies, we developed a plastic optical fiber (POF) immunosensor using an optoelectronic configuration consisting of a U-Shape probe connected to an LED and a photodetector. Bacterial detection was evaluated with the immunosensor immersed in a bacterial suspension in water with a known concentration. Here, we report on the sensitivity of a new optoelectronic configuration consisting of two POF U-shaped probes, one as the reference and the other as the immunosensor, for the detection of Escherichia coli. In addition, another methos of detection was tested where the sensors were calibrated in the air, before being immersed in a bacterial suspension and then read in the air. This modification improved sensor sensitivity and resulted in a faster detection time. After the immunocapture, the sensors were DAPI-stained and submitted to confocal microscopy. The histograms obtained confirmed that the responses of the immunosensors were due to the bacteria. This new sensor detected the presence of E. coli at 10⁴ CFU/mL in less than 20 min. Currently, sub-20 min is faster than previous studies using fiber-optic based biosensors. We report on an inexpensive and faster detection technology when compared with conventional methods. Full article

Bite force measurements are crucial in the realm of biomedical research, particularly in the areas of dentistry and orthodontic care. Various intraoral devices have been used to assess biting force, but each has limitations and drawbacks. Fiber optic sensors (FOSs) offer advantages such as electrical inertness, immunity to electromagnetic interference, and high sensitivity. Distributed fiber optic sensing allows an increase in the number of sensing points and can interrogate numerous reflections from scattering events within an optical fiber. We present four dental bites with heights of 6 mm, which enabled bilateral measurements. U-shaped sensors were prepared by embedding fibers into silicone by folding a single-mode fiber into four lines and multiplexing eight parallel nanoparticle-doped fibers. Dental bite models were created using two silicone materials (Sorta Clear 18 and Sorta Clear 40). The developed sensors were calibrated by applying weights up to 900 g, resulting in a linear response. Experiments were conducted to compare the efficacy of the dental bites. The collection of massive data was enabled by constructing a 2D map of the dental bites during multi-point sensing. Full article

Optical fiber biosensors can be used to develop point-of-care tests (POCTs) for detecting viruses and bacteria in several matrices. In particular, the surface plasmon resonance (SPR) and localized SPR phenomena (LSPR) can be excited by exploiting low-cost and small-size optical fiber chips. Generally, SPR or LSPR sensors are realized using several kinds of modified optical fibers (silica, plastic, or specialty) or by exploiting other optical waveguides (e.g., slab, spoon-shaped waveguides, etc.). More specifically, optical fiber sensors can be classified as intrinsic or extrinsic. In the “optical fiber intrinsic sensors”, the sensing area is realized in the optical fiber directly, such as in the case of plasmonic platforms based on D-shaped plastic optical fibers (POFs), tapered optical fibers, U-bend POFs, or light-diffusing fibers (LDFs). By contrast, when an optical fiber is used as a mere waveguide allowing for the launch of light to the sensing region and its collection, it is defined as an extrinsic optical fiber sensor, like in the case of the plasmonic sensors realized by Cennamo et al. using POFs combined with spoon-shaped waveguides, 3D-printed platforms, bacterial cellulose waveguides, nanogratings, and InkJet-printed chips. To realize optical biosensor chips for the detection of viruses and bacteria, both intrinsic and extrinsic plasmonic POF sensors can be efficiently combined with receptors specific for membrane proteins, either biological (e.g., antibodies, aptamers, enzymes, etc.) or synthetic (e.g., molecularly imprinted polymers), to build groundbreaking POCTs. Full article

In this paper, a tapered fiber bioprobe based on Mach–Zehnder interference (MZI) is proposed. To retain the highly sensitive straight-tapered fiber MZI sensing structure, we designed a U-shaped transmission fiber structure for the collection of optical sensing signals to achieve a miniature-insert-probe design. The spectrum responses from the conventional straight-tapered fiber MZI sensor and our proposed sensor were compared and analyzed, and experimental results showed that our proposed sensor not only has the same sensing capability as the straight-tapered fiber sensor, but also has the advantages of being flexible, convenient, and less liquid-consuming, which are attributed to the inserted probe design. The tapered fiber bioprobe obtained a sensitivity of 1611.27 nm/RIU in the refractive index detection range of 1.3326–1.3414. Finally, immunoassays for different concentrations of human immunoglobulin G were achieved with the tapered fiber bioprobe through surface functionalization, and the detection limit was 45 ng/mL. Our tapered fiber bioprobe has the insert-probe advantages of simpleness, convenience, and fast operation. Simultaneously, it is low-cost, highly sensitive, and has a low detection limit, which means it has potential applications in immunoassays and early medical diagnosis. Full article

The extensive use of antibiotics has become a serious concern due to certain deficiencies in wastewater facilities, their resistance to removal, and their toxic effects on the natural environment. Therefore, substantial attention has been given to the detection of antibiotics because of their potential detriment to the ecosystem and human health. In the present study, a novel design of indium tin oxide (ITO) coated U-shaped fiber optic lossy mode resonance (LMR) biosensor is presented for the sensitive detection of the antibiotic ciprofloxacin (CIP). The performance of the designed U-shaped LMR sensor is characterized in terms of its sensitivity, full width at half maximum (FWHM), the figure of merit (FOM), and the limit of detection (LOD). For the proposed U-shaped LMR sensing probe, the various crucial factors such as the thickness (d) of the ITO layer, sensing region length (L), and bending radius (R) are optimized. The thickness of the ITO layer is optimized in such a way that two LMR curves are observed in the transmission spectrum and, thereafter, the performance parameters are evaluated for each LMR. It is observed that the designed U-shaped LMR sensor with optimized parameters shows an approximately seven-fold enhancement in sensitivity compared to the straight-core fiber optic LMR sensor. The numerical results revealed that the designed U-shaped fiber optic LMR biosensor can provide a maximum sensitivity of 17,209.9 nm/RIU with the highest FOM of 91.42 RIU⁻¹, and LOD of 6.3 × 10⁻⁵ RIU for the detection of CIP hydrochloride in the concentration range of 0.001 to 0.029 mol∙dm⁻³. Thus, it is believed that the designed LMR biosensor can practically explore its potential use in environmental monitoring and biomedical applications and hence, opens a new window of opportunity for the researchers working in the field of U-shaped fiber optic LMR biosensing. Full article

We report the design, fabrication, and testing of a humidity sensor based on an optical fiber-based evanescent wave probe. The fiber was bent into a U-shape and de-cladded at the location of the bending. The de-cladded section was coated either with Au or with ZnO nanoparticles. Humidity is detected based on the interaction in the surface plasmon resonance of the Au/ZnO nanoparticles excited by an evanescent wave of light passing through the optical fiber. The response of the U-bent fibers to humidity was investigated using a specifically designed low-voltage portable interrogation box. We found that the fibers coated with ZnO nanoparticles were able to detect a minimum 0.1% change in humidity with an average sensitivity of 143 µV/%RH and 95% linearity over the 10% to 80% humidity range. In comparison, samples coated with Au and Au + ZnO nanoparticles demonstrated a minimum change detection of 0.3% RH and 2% RH respectively. The response and recovery time of the sensor were measured to be 3 s and 4 s, respectively, for a 60% change in humidity from 20% to 80%. The entire measurement system was operated by consuming an electrical power of 1.62 W at an input voltage of 12 Vdc. Full article

High-resolution distributed reinforcement strain measurements can provide invaluable information for developing and evaluating numerical and analytical models of reinforced concrete structures. A recent testing campaign conducted at UCLouvain in Belgium used fiber-optic sensors embedded along several longitudinal steel rebars of three reinforced concrete U-shaped walls. The resulting experimental dataset provides an opportunity to evaluate and compare, for different types of loading, the strain measurements obtained with the fiber-optic sensors in the confined core of the structural member against more conventional and state-of-the-practice sensors that monitor surface displacements and deformations. This work highlights the need to average strain measurements from digital image correlation techniques in order to obtain coherent results with the strains measured from fiber optics, and investigates proposals to achieve this relevant goal for research and engineering practices. The longitudinal strains measured by the fiber optics also provide additional detailed information on the behavior of these wall units compared to the more conventional instrumentation, such as strain penetration into the foundation and head of the wall units, which are studied in detail. Full article

This paper presents the development and application of a multiplexed intensity variation-based sensor system for multiplane shape reconstruction. The sensor is based on a polymer optical fiber (POF) with sequential lateral sections coupled with a flexible light-emitting diode (LED) belt. The optical source modulation enables the development of 30 independent sensors using one photodetector, where the sensor system is embedded in polydimethylsiloxane (PDMS) resin in two configurations. Configuration 1 is a continuous PDMS layer applied in the interface between the flexible LED belt and the POF, whereas Configuration 2 comprises a 20 mm length PDMS layer only on each lateral section and LED region. The finite element method (FEM) is employed for the strain distribution evaluation in different conditions, including the strain distribution on the sensor system subjected to momentums in roll, pitch and yaw conditions. The experimental results of pressure application at 30 regions for each configuration indicated a higher sensitivity of Configuration 1 (83.58 a.u./kPa) when compared with Configuration 2 (40.06 a.u./kPa). However, Configuration 2 presented the smallest cross-sensitivity between sequential sensors (0.94 a.u./kPa against 45.5 a.u./kPa of Configuration 1). Then, the possibility of real-time loading condition monitoring and shape reconstruction is evaluated using Configuration 1 subjected to momentums in roll, pitch and yaw, as well as mechanical waves applied on the sensor structure. The strain distribution on the sensor presented the same pattern as the one obtained in the simulations, and the real-time response of each sensor was obtained for each case. In addition, the possibility of real-time loading condition estimation is analyzed using the k-means algorithm (an unsupervised machine learning approach) for the clusterization of data regarding the loading condition. The comparison between the predicted results and the real ones shows a 90.55% success rate. Thus, the proposed sensor device is a feasible alternative for integrated sensing in movement analysis, structural health monitoring submitted to dynamic loading and robotics for the assessment of the robot structure. Full article

With the development of virtual reality (VR) interaction technology, data glove has become one of the most popular devices for human-computer interaction. It’s valuable to design high-sensitive and flexible sensor for data glove. Therefore, a low-cost data glove based on self-compensating elastic optical fiber sensor with self-calibration function is proposed. The tunable and stretchable elastic fiber was fabricated by a simple, economical and controllable method. The fiber has good flexibility and high stability under stretching, bending and indentation deformation. The optical fibers are installed in the sensor in a U shape with a bending radius of 5 mm. Compared with the straight fiber, the response sensitivity of the U-shaped fiber to deformation is increased by about 7 times at most. The reference optical fiber is connected to the sensor, which effectively improves the stability and accuracy of the sensor system. In addition, the sensors are easy to install so that the data gloves can be customized for different hand shapes. In the gesture capture test, it can respond quickly and guide the manipulator to track the gesture. This responsive and stable data glove has broad development potential in motion monitoring, telemedicine and human-computer interaction. Full article

We have proposed and experimentally demonstrated a dual-parameter optical fiber sensor for simultaneous measurement of magnetic field and temperature. The sensor is a magnetofluid-coated single-mode fiber (SMF)-U-shaped hollow-core fiber (UHCF)-single-mode fiber (SMF) (SMF-UHCF-SMF) fiber structure. Combined with the intermodal interference and the macro-bending loss of the U-shaped fiber structure, the U-shaped fiber sensor with different bend diameters was investigated. In our experiments, the transmission spectra of the sensor varied with magnetic field strength and temperature around the sensing structure, respectively. The dip wavelengths of the interference spectra of the proposed sensor exhibit red shifts with magnetic field strength and temperature, and the maximum sensitivity of magnetic field strength and temperature were 1.0898 nm/mT and 0.324 nm/°C, respectively. Full article