Search Results (2,629)

Multilayer heterostructures of [(BiFeO₃)_m/(SrTiO₃)_n]_p were synthesized on ITO-coated quartz substrates via pulsed laser deposition, with varying thickness ratios (r = n/m) and periodicities (p = 1–3). Structural, electrical, and piezoelectric properties were systematically investigated using X-ray diffraction, AFM, and PFM. The BiFeO₃ layers crystallized in a distorted rhombohedral phase (R3c), free of secondary phases. Compared to single-layer BiFeO₃ films, the multilayers exhibited markedly lower leakage current densities and enhanced piezoelectric response. Electrical conduction transitioned from space-charge-limited current at low fields (E < 100 kV/cm) to Fowler–Nordheim tunneling at high fields (E > 100 kV/cm). Optimal performance was achieved for r = 0.30, p = 1, with minimal leakage (J = 8.64 A/cm² at E = 400 kV/cm) and a peak piezoelectric coefficient (d₃₃ = 55.55 pm/V). The lowest coercive field (Ec = 238 kV/cm) occurred in the configuration r = 0.45, p = 3. Saturated hysteresis loops confirmed stable ferroelectric domains. These findings demonstrate that manipulating layer geometry in [(BiFeO₃)_m/(SrTiO₃)_n]_p stacks significantly enhances functional properties, offering a viable path toward efficient, lead-free piezoelectric nanodevices. Full article

Detailed description of phase composition and geochemistry of the Muschelkalk carbonate rocks of the Upper Silesian Province in Poland were presented in this article. The tests were carried out to determine mineralogical features and geochemical properties. The samples were collected from the formations of the Lower Muschelkalk (Gogolin Unit), Middle Muschelkalk (Diplopore Dolomite Unit) and Upper Muschelkalk (Tarnowice Unit, Boruszowice Unit). The following research methods were used: macroscopic description, X-Ray Diffraction, Fourier transform infrared spectroscopy, X-Ray Fluorescence and Atomic spectrometry with plasma intensification. The following carbonate phases were identified: a low-Mg calcite, a high-Mg calcite, a proto-dolomite, an ordered dolomite and a huntite. The results of XRD analysis allowed the determination of the chemical formulas of the mineral phases. XRF and ICP AES analyses allowed to establish the content of following trace elements: Sr, Ba, Al, Si, Fe, Mn, K, Na, S, Cl, Ti, Cr, Ni, Zn, Rb, Zr, Pb, As, V, Be, B, Co, Cu, Br, Mo and Cd. Apart from Sr and Ba, they are not fundamental components of carbonate rocks. They indicate the presence of minerals such as silicates, aluminosilicates, oxides and sulfides. Full article

Green synthesis represents a sustainable, reliable, and eco-friendly approach for producing various materials and nanomaterials, including metal and metal oxide nanoparticles. This environmentally conscious method has garnered significant attention from materials scientists. In recent years, interest in plant-mediated nanoparticle synthesis has grown markedly, owing to advantages such as enhanced product stability, low synthesis costs, and the use of non-toxic, renewable resources. This review specifically focuses on the green synthesis of metal oxide nanoparticles using plant extracts, highlighting five key oxides: TiO₂, ZnO, WO₃, CuO, and Fe₂O₃, which are prepared through various plant-based methods. The release of toxic effluents like synthetic dyes into the environment poses serious threats to aquatic ecosystems and human health. Therefore, the application of biosynthesized nanoparticles in removing such pollutants from industrial wastewater is critically examined. This paper discusses the synthesis routes, characterization techniques, green synthesis methodologies, and evaluates the photocatalytic performance and dye degradation mechanisms of these plant-derived nanoparticles. Full article

Traditional liquid electrolyte batteries face safety concerns such as leakage and flammability, while further optimization has reached a bottleneck. Solid electrolytes are therefore considered a promising solution. Here, a PEO–LiTFSI–LATP (PELT) composite electrolyte was developed by incorporating nanosized Li_1.3Al_0.3Ti_1.7(PO₄)₃ fillers into a polyethylene oxide matrix, effectively reducing crystallinity, enhancing mechanical robustness, and providing additional Li⁺ transport channels. The PELT electrolyte exhibited an electrochemical stability window of 4.9 V, an ionic conductivity of 1.2 × 10⁻⁴ S·cm⁻¹ at 60 °C, and a Li⁺ transference number (tLi+) of 0.46, supporting stable Li plating/stripping for over 600 h in symmetric batteries. More importantly, to address poor electrode–electrolyte contact in conventional layered cells, we proposed an integrated electrode–electrolyte architecture by in situ coating the PELT precursor directly onto LiFePO₄ cathodes. This design minimized interfacial impedance, improved ion transport, and enhanced electrochemical stability. The integrated PELT/LFP battery retained 74% of its capacity after 200 cycles at 1 A·g⁻¹ and showed superior rate capability compared with sandwich-type batteries. These results highlight that coupling LATP-enhanced polymer electrolytes with an integrated architecture is a promising pathway toward high-safety, high-performance solid-state lithium-ion batteries. Full article

NASICON-type Li_1+XFe_XTi_2-X(PO₄)₃ (x = 0.1, 0.3, 0.4) solid electrolytes for all-solid-state Li-ion batteries were synthesized using a sol–gel method. This study investigated the impact of substituting Fe³⁺ (0.645 Å), a trivalent cation, for Ti⁴⁺ (0.605 Å) on ionic conductivity. Li_1+XFe_XTi_2-X(PO₄)₃ samples, subjected to various sintering temperatures, were characterized using TG-DTA, XRD with Rietveld refinement, XPS, FE-SEM, and AC impedance to evaluate composition, crystal structure, fracture-surface morphology, densification, and ionic conductivity. XRD analysis confirmed the formation of single-crystalline NASICON-type Li_1+XFe_XTi_2-X(PO₄)₃ at all sintering temperatures. However, impurities in the secondary phase emerged owing to the high sintering temperature above 1000 °C and increased Fe content. Sintered density increased with the densification of Li_1+XFe_XTi_2-X(PO₄)₃, as evidenced by FE-SEM observations of sharper edges of larger quasi-cubic grains at elevated sintering temperatures. At 1000 °C, with Fe content exceeding 0.4, grain coarsening resulted in additional grain boundaries and internal cracks, thereby reducing the sintered density. Li_1.3Fe_0.3Ti_1.7(PO₄)₃ sintered at 900 °C exhibited the highest density among the other conditions and achieved the maximum total ionic conductivity of 1.51 × 10⁻⁴ S/cm at room temperature, with the lowest activation energy for Li-ion transport at 0.37 eV. In contrast, Li_1.4Fe_0.4Ti_1.6(PO₄)₃ sintered at 1000 °C demonstrated reduced ionic conductivity owing to increased complex impedance associated with secondary phases and grain crack formation. Full article

This study investigates the mechanism behind the heat-induced color change (brown to yellowish green) in Mn- and Fe-rich elbaite tourmaline under reducing atmosphere at 500 °C. A combination of analytical techniques including gemological characterization, electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, and ultraviolet–visible (UV-Vis) spectroscopy was employed. Chemical analysis confirmed the samples as intermediate members of the elbaite–fluorelbaite series, with an average formula of ^X(Na₀.₆₆ □₀.₂₆ Ca₀.₀₈) _Σ1.₀₀^Y(Li₁.₂₉Al₁.₁₀Mn₀.₃₁ Fe²⁺₀.₁₅Ti₀.₀₁Zn₀.₀₁) _Σ2.₈₇ ^ZAl₆^T[Si₆O₁₈] (BO₃)₃^V(OH)₃.₀₀^W(OH₀.₅₁F₀.₄₉) _Σ1.₀₀, enriched in Mn (17,346–20,669 μg/g) and Fe (8396–10,750 μg/g). Heat treatment enhanced transparency and induced strong pleochroism (yellowish green parallel c-axis, brown perpendicular c-axis). UV-Vis spectroscopy identified the brown color origin in the parallel c-axis direction: absorption bands at 730 nm (Fe²⁺ d–d transition, ⁵T_2g → ⁵E_g), 540 nm (Fe²⁺→Fe³⁺ intervalence charge transfer, IVCT), and 415 nm (Fe²⁺→Ti⁴⁺ IVCT + possible Mn²⁺ contribution). Post-treatment, the 540 nm band vanished, creating a green transmission window and causing the color shift parallel the c-axis. The spectra perpendicular to the c-axis remained largely unchanged. The disappearance of the 540 nm band, attributed to the reduction of Fe³⁺ to Fe²⁺ eliminating the Fe²⁺–Fe³⁺ pair interaction required for IVCT, is the primary color change mechanism. The parallel c-axis section of the samples shows brown and yellow-green dichroism after heat treatment. A decrease in the IR intensity at 4170 cm⁻¹ indicates a reduced Fe³⁺ concentration. The weakening or disappearance of the 4721 cm⁻¹ absorption band of the infrared spectrum and the near-infrared 976 nm absorption band of the ultraviolet–visible spectrum provides diagnostic indicators for identifying heat treatment in similar brown elbaite–fluorelbaite. Full article

Myanmar blue jadeite jade is a rare and highly prized gemstone, yet its coloration and formative mechanisms remain poorly understood. In this study, petrographic analysis, ultraviolet–visible (UV–Vis) spectroscopy, electron probe microanalysis (EPMA), and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) were performed on a sample of Myanmar blue jadeite with small white blocks to investigate its mineral composition, trace element distribution, and coloration mechanisms. Most of the sample was found to be blue, with surrounding white areas occurring in small ball-shaped blocks. The main mineral component in both the blue and white domains was jadeite. Although both areas underwent recrystallization, their textures differed significantly. The blue areas retained primary structural features within a medium- to fine-grained texture, reflecting relatively weaker recrystallization. The white areas, however, were recrystallized into a micro-grained texture, reflecting relatively stronger recrystallization, with the superimposed effects of external stress producing a fragmented appearance. The blue jadeite had relatively higher contents of Ti, Fe, Ca, and Mg, while the white jadeite contained compositions close to those of near-end-member jadeite. It was noted that, while white jadeite may have a high Ti content, its Fe content is low. UV–Vis spectra showed a broad absorption band at 610 nm associated with Fe²⁺-Ti⁴⁺ charge transfer and a gradually increasing absorption band starting at 480 nm related to V⁴⁺. Combining the chemical composition and the characteristics of the UV–Vis spectra, we infer that the blue coloration of jadeite is attributed to Fe²⁺-Ti⁴⁺ charge transfer; i.e., the presence of both Ti and Fe in blue jadeite plays a key role in its color formation. V⁴⁺ exhibited no significant linear correlation with the development of blue coloration. Prominent oscillatory zoning was observed in the jadeite, transitioning from NaAlSi₂O₆-dominant cores to Ca-Mg-Fe-Ti-enriched rims, reflecting the trend of fluid evolution during blue jadeite crystallization. Petrographic analysis indicated that the formation of the Myanmar blue jadeite occurred in two or three stages, with the blue regions forming earlier than the white regions. The blue jadeite also underwent significant recrystallization. Our findings contribute to the understanding of the formation of blue jadeite and the diversity of colors in jadeite jade. Full article

In wastewater treatment, sludge is generated during both the primary and secondary sedimentation processes. With the growing volume of wastewater, sludge production has increased accordingly. Prior to subsequent treatment or disposal, sludge dewatering is a critical step to reduce volume and improve treatment efficiency. The primary challenge lies in the removal of bonded water within the extracellular polymeric substances (EPSs) and the microorganism cells. In this study, electrochemical pretreatment was employed to improve sludge dewatering performance. The optimal electrochemical treatment was achieved at an electrode spacing of 2 cm, a stirring speed of 500 rpm, and an electrolyte (1 M calcium chloride, CaCl₂) dosage of 3 mL for 50 min. Subsequently, flocculation was conducted. Compared with the widely used polyacrylamide (PAM), polydimethyldiallylammonium chloride (PDMDAAC) achieved superior dewatering performance with less than half the dosage required. Under the combined treatment, the final moisture content of the sludge cake was reduced to 53.2%. These findings indicate that the combination of Fe/Ti-based electrochemical pretreatment and flocculation process is a promising and efficient strategy for deep sludge dewatering. Full article

In this paper, 316 stainless steel/TiC coatings with different LaB₆ contents (0%, 2%, 4%, 6%) were prepared on the surface of 45 steel by laser cladding technology. The effects of the LaB₆ content on the phase composition, microstructure, microhardness, and wear resistance of the coatings were studied. The results show that without the LaB₆ addition, the coating is composed of Austenite and TiC phases, with defects such as pores and cracks, and the microstructure is mainly equiaxed grains. With the addition of LaB₆, Fe-Cr phases are formed in the coating, and the microstructure transforms into columnar grains and dendritic grains. The grains are first refined and then coarsened, among which the coating with 4% LaB₆ (C4) has the smallest grain size. The experimental results indicate that the microhardness of the coatings first increases and then decreases with the increase in the LaB₆ content, and the C4 coating has the highest microhardness (594HV_0.2). The wear rate shows the same variation trend. The C4 coating has the lowest wear rate and the best wear resistance. This is attributed to the synergistic effect of the fine grain strengthening and TiC particle dispersion strengthening. Full article

Grape pomace (GP), a significant by-product of winemaking, is gaining increasing recognition for its potential as a source of bioactive compounds with antioxidant and cardioprotective properties. This study aimed to characterize the polyphenolic profile, fatty acid composition, and antioxidant activity of 17 GP samples from Transylvanian cultivars. Polyphenolic content was determined using the Folin–Ciocalteu method and high-performance liquid chromatography coupled with diode array detection and electrospray ionization mass spectrometry (HPLC–DAD–ESI MS) analysis. Fatty acid composition was analyzed using gas chromatography with flame ionization detection (GC–FID). Antioxidant capacity was assessed using five methods, which included the 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging, 2,2′-azino-bis (3-ethylbenzothialzoline-6-sulfonic acid) (ABTS) radical scavenging, ferric-reducing antioxidant power (FRAP), cupric ion reducing antioxidant capacity (CUPRAC), and reducing power (RP) assays. Additionally, all extracts were analyzed by Fourier transform infrared (FTIR) spectroscopy to identify the presence of functional groups and chemical bonds associated with bioactive compounds. The results showed that Neuburger (NE), Radames (RA), and Regent (RE) cultivars had the highest phenolic concentrations, particularly of catechin, epicatechin, and procyanidin dimers. NE and Feteascǎ Regalǎ (FR) exhibited the greatest radical scavenging and electron transfer activities across multiple antioxidant assays. Rose Blaj (RB) and Astra (AS) displayed the most favorable fatty acid profiles, with high unsaturated-to-saturated fatty acid (UFA/SFA) and hypocholesterolemic-to-hypercholesterolemic fatty acid (H/H) ratios, as well as low atherogenicity (AI) and thrombogenicity (TI) indices, suggesting cardioprotective potential. Additionally, RB and NE cultivars also demonstrated a strong chelation of Cu²⁺ and Fe²⁺ ions, enhancing their antioxidant efficacy by mitigating metal-catalyzed oxidative stress. These findings underscore the potential of GP, particularly from NE, RB, RA, and AS cultivars, the last three of which were homologated in Transylvania at SCDVV Blaj, as valuable sources of health-promoting compounds for use in food, nutraceuticals, and other health-related applications. Full article

Binary oxide ceramics have emerged as key materials in solar energy research due to their versatility, chemical stability, and tunable electronic properties. This study presents a comparative analysis of seven prominent oxides (TiO₂, ZnO, Al₂O₃, SiO₂, CeO₂, Fe₂O₃, and WO₃), focusing on their functional roles in silicon, perovskite, dye-sensitized, and thin-film solar cells. A bibliometric analysis covering over 50,000 publications highlights TiO₂ and ZnO as the most widely studied materials, serving as electron transport layers, antireflective coatings, and buffer layers. Al₂O₃ and SiO₂ demonstrate highly specialized applications in surface passivation and interface engineering, while CeO₂ offers UV-blocking capability and Fe₂O₃ shows potential as an absorber material in photoelectrochemical systems. WO₃ is noted for its multifunctionality and suitability for scalable, high-rate processing. Together, these findings suggest that binary oxide ceramics are poised to transition from supporting roles to essential components of stable, efficient, and environmentally safer next-generation solar cells. Full article

This study investigates the use of preliminary thermochemical activation in a NaHCO₃ solution under elevated pressure and temperature to modify the chemically stable and hard-to-process phase composition of various mineral raw materials and improve the recovery of valuable components. The method was tested on various types of mineral raw materials, including slag from the reductive smelting of red mud from alumina production prior to acid leaching, ash before chemical beneficiation, gibbsite–kaolinite bauxite prior to gravity separation, and nephelines, for which the sintering process was replaced with chemical beneficiation. The slag from the reductive smelting of red mud was also tested before acid leaching. The activation of slag enhanced tricalcium silicate formation lead to leaching recoveries of ~96% for rare earth elements, ~92% for TiO₂, ~98% for CaO and Al₂O₃, and 50% for Fe₂O₃, compared to much lower values without activation. With ash, activation eliminated the sillimanite and hedenbergite phases, increased mullite and free silica, and formed calcite, resulting in a 15–20% higher silica recovery. With gibbsite–kaolinite bauxite, activation altered kaolinite, siderite, quartz, and hematite contents; eliminated calcium silicate; and improved the silicon modulus of the sand fraction by 35.9% during gravity beneficiation. For nepheline ore, activation promoted the formation of albite and hydrosodalite, eliminated corundum and andradite, and increased silica recovery from 33.58% to 59.6%. These results demonstrate that thermochemical activation effectively transforms mineral structures and significantly improves the efficiency of subsequent beneficiation processes. Full article

The growing accumulation of waste lubricating oil presents serious environmental issues, calling for sustainable management solutions. This research discusses the creation of FeNi/TiO₂ nanocatalysts that were synthesized through an eco-friendly method utilizing grape seed extract (GSE) as a natural reducing agent for the catalytic pyrolysis of waste lubricating oil. The nanocatalyst was produced using the microemulsion technique and refined via Response Surface Methodology (RSM) to optimize its catalytic performance. Pyrolysis was carried out at 400 °C, leading to a significant conversion of waste oil into valuable fuel. The FeNi/TiO₂ nanocatalyst exhibited exceptional capabilities in facilitating the breakdown of heavy hydrocarbons into lighter fuel fractions while reducing unwanted byproducts. GC-MS analysis demonstrated the prevalence of C6–C20 hydrocarbons in the pyrolysis oil, underscoring its potential as a high-quality alternative fuel similar to traditional diesel. This study aids in the progress of environmentally sustainable waste-to-energy technologies, offering a promising pathway for effective fuel production and hazardous waste management. Full article

The Hugushan banded iron formation (BIF) is one of the most representative iron ore deposits in the central part of the North China Craton, and its ore formation mechanism remains highly controversial. This study presents whole-rock and Fe–Si–O isotope geochemical evidence, offering a new perspective on the ore formation mechanism of the Hugushan BIFs. The samples from the upper and lower parts of the Hugushan BIFs are characterized by slight enrichment of heavy and light Fe isotopes, respectively. Additionally, the samples from the upper part of the Hugushan BIFs show characteristics of slightly positive Ce anomalies and negative La anomalies, suggesting that the shallow ancient seawater was in a partially oxidized state, whereas the deep seawater remained in a reductive environment during the depositional period. The low Al₂O₃ and TiO₂ concentrations, as well as the depletion of Zr and Hf in the Hugushan BIFs, suggest that the contribution of terrestrial detrital materials to deposition is extremely limited. The BIFs all exhibit positive Eu anomalies, and the quartz in the BIFs is depleted in ³⁰Si, a characteristic similar to that observed in siliceous rocks formed in hydrothermal vent environments and during hydrothermal plume activity. Additionally, the δ¹⁸O values of quartz in Hugushan BIFs are similar to the O isotope compositions of hydrothermal sedimentary siliceous rocks, further suggesting that the silicon in BIFs originates primarily from seafloor hydrothermal activity. The combination of Eu/Sm, Sm/Yb, and Y/Ho ratios indicates that the major components (iron and silica) of the Hugushan Iron Ore Deposit originated from the mixing of high-temperature hydrothermal fluids with seawater, with the hydrothermal fluid contributing slightly less than 0.1%. The magnetite and quartz bands in the BIFs exhibit inhomogeneous and covariant δ⁵⁶Fe and δ³⁰Si isotope characteristics, suggesting that the alternating siliceous and ferruginous layers are products of original chemical deposition in the ocean. Periodic hydrothermal activity and ocean transgression caused the recurring deposition of siliceous and ferruginous layers, resulting in the characteristic banded structure of the Hugushan Iron Ore Deposit. Full article

Novel structural materials, high-entropy alloys (HEAs), have attracted considerable interest owing to their tunable microstructural designs and adjustable mechanical properties. In the present work, the microstructural evolution and tensile deformation behavior of FeCoNiCrTi_0.2 HEA are comprehensively examined through cold rolling (with 80% thickness reduction) followed by annealing, combined with multiscale characterization techniques (EBSD/TEM) and mechanical tests. The results reveal that the as-rolled microstructure was characterized by the presence of strong Brass, Goss/Brass, and S textures, along with the formation of high-density dislocation walls (DDWs) and dislocation cells (DCs). As the annealing temperature increased, recrystallized grains preferentially nucleated at grain boundaries with higher stress concentrations and dislocation densities. The grain size decreased from 120.33 μm in the as-rolled state to 10.26 μm after annealing at 1000 °C. Low-angle grain boundaries (LAGBs) progressively transformed into high-angle grain boundaries (HAGBs), while the fraction of Σ3 twin boundaries initially decreased and subsequently increased, reaching a maximum of 43.7% after annealing at 1000 °C. At annealing temperatures exceeding 800 °C, deformed grains became equiaxed, with partial retention of primary texture components observed. After annealing at 1000 °C, the yield strength and tensile strength decreased compared to the as-rolled state, while the elongation significantly increased from 17.2% to 69.8% Simultaneously, the yield ratio decreased by 53%, and the strain-hardening capacity was enhanced. Ultimately, a constitutive model integrating the influences of dislocation mean free path and twin boundary obstruction was developed, providing microscopic explanations for the inverse relationship between strength and recrystallization fraction. Full article