Search Results (71)

The effects of Ce incorporation into trimetallic PtSnIn-supported catalysts were investigated for a propane dehydrogenation reaction with advanced characterization techniques. It was found that some Ce species exist in the form of CeAlO₃ on the reduced PtSnIn/xCe-Al catalyst, significantly enhancing the thermal stability of the alumina support. The NH₃-TPD measurements verified that the total acidity of the PtSnIn/xCe-Al catalysts decreases with the addition of Ce. The PtSnIn/1.5Ce-Al catalyst exhibits the optimal particle distribution with the smallest Pt particle size of 8.0 nm, which was revealed by TEM. The H₂-TPR and XPS results suggest that more oxidized-state Sn species form on catalyst surfaces, and the metal–support interaction can be strengthened when Ce is introduced. Furthermore, TG analysis demonstrates that Ce incorporation substantially reduces coke formation on the spent catalysts. The PtSnIn/1.5Ce-Al catalyst exhibits exceptional catalytic performance, achieving an initial propane conversion of 62.6% and maintaining a conversion of 57.2% after a 120 min reaction. In addition, the PtSnIn/1.5Ce-Al catalyst possesses high long-term stability. Over 40.0% propane conversion can be maintained after a 53 h continuous PDH reaction. These findings highlight the pivotal role of Ce in improving the structural properties and catalytic performance of PtSnIn-based catalysts for propane dehydrogenation, offering valuable insights for the design of highly efficient and stable dehydrogenation catalysts. Full article

To achieve the “double carbon” goal, it is urgent to reform the energy system. The oxygen evolution reaction (OER) is a vital semi-reaction for many new energy-storage and conversion devices. Metal nanoparticles embedded in heteroatom-doped carbon materials prepared by the pyrolyzing of metal–organic frameworks (MOFs) have been a key route to obtain high-performance electrochemical catalysts. Herein, a nanocatalyst embedding Ni nanoparticles into S- and N-co-doped carbon nanoplate (Ni NPs@SN-CNP) has been synthesized by pyrolysis of a Ni-MOF precursor. The prepared Ni NPs@SN-CNP exhibits superior oxygen evolution performance with an overpotential of 256 mV to attain 10 mA cm⁻² and a low Tafel slope value of 95 mV dec⁻¹. Moreover, a self-assembled overall-water-splitting cell with Ni NPs@SN-CNP/NF||Pt-C/NF achieves a low potential of 1.56 V at 10 mA cm⁻² and a high cycling stability for at least 10 h. The improvement in this performance is benefit from its large surface area, unique morphology, and the nanostructure of the electrocatalyst. This study presents a novel and simple approach to designing high-performance OER catalysts. Full article

The development of state-of-the-art gas sensors based on metal oxide semiconductors (MOS) to monitor hazardous and greenhouse gas (e.g., methane, CH₄, and carbon dioxide, CO₂) has been significantly advanced. Moreover, the morphological and topographical structures of MOSs have significantly influenced the gas sensors by means of surface catalytic activities. This work examines the impact of morphological and topological networked assembly of zinc oxide (ZnO) nanostructures, including microparticles and nanoparticles (0D), nanowires and nanorods (1D), nanodisks (2D), and hierarchical networks of tetrapods (3D). Gas sensors consisting of vertically aligned ZnO nanorods (ZnO–NR) and topologically interconnected tetrapods (T–ZnO) of varying diameter and arm thickness synthesized using aqueous phase deposition and flame transport method on interdigitated Pt electrodes are evaluated for methane detection. Smaller-diameter nanorods and tetrapod arms (nanowire-like), having higher surface-to-volume ratios with reasonable porosity, exhibit improved sensing behavior. Interestingly, when the nanorods’ diameter and interconnected tetrapod arm thickness were comparable to the width of the depletion layer, a significant increase in sensitivity (from 2 to 30) and reduction in response/recovery time (from 58 s to 5.9 s) resulted, ascribed to rapid desorption of analyte species. Additionally, nanoparticles surface-catalyzed with Pd (~50 nm) accelerated gas sensing and lowered operating temperature (from 200 °C to 50 °C) when combined with UV photoactivation. We modeled the experimental findings using a modified general formula for ZnO methane sensors derived from the catalytic chemical reaction between methane molecules and oxygen ions and considered the structural surface-to-volume ratios (S/V) and electronic depletion region width (L_d) applicable to other gas sensors (e.g., SnO₂, TiO₂, MoO₃, and WO₃). Finally, the effects of UV light excitation reducing detection temperature help to break through the bottleneck of ZnO-based materials as energy-saving chemiresistors and promote applications relevant to environmental and industrial harmful gas detection. Full article

This study explores the development of core–shell electrocatalysts for efficient glycerol oxidation in alkaline media. Carbon-supported M@Pt/C (M = Co, Ni, Sn) catalysts with a 1:1 atomic ratio of metal (M) to platinum (Pt) were synthesized using a facile sodium borohydride reduction method. The analysis confirmed the formation of the desired core–shell structure, with Pt dominating the surface as evidenced by energy-dispersive X-ray spectroscopy (EDS). X-ray diffraction (XRD) revealed the presence of a face-centered cubic (fcc) Pt structure for Co@Pt/C and Ni@Pt/C. Interestingly, Sn@Pt/C displayed a PtSn alloy formation indicated by shifted Pt peaks and the presence of minor Sn oxide peaks. Notably, no diffraction peaks were observed for the core metals, suggesting their amorphous nature. Electrocatalytic evaluation through cyclic voltammetry (CV) revealed superior glycerol oxidation activity for Co@Pt/C compared to all other catalysts. The maximum current density followed the order Co@Pt/C > Ni@Pt/C > Sn@Pt/C > Pt/C. This highlights the effectiveness of the core–shell design in enhancing activity. Furthermore, Sn@Pt/C displayed remarkable poisoning tolerance attributed to a combined effect: a bifunctional mechanism driven by Sn oxides and an electronic effect within the PtSn alloy. These findings demonstrate the significant potential of core–shell M@Pt/C structures for designing highly active and poisoning-resistant electrocatalysts for glycerol oxidation. The presented approach paves the way for further development of optimized catalysts with enhanced performance and stability aiming at future applications in direct glycerol fuel cells. Full article

A huge variety of chemical commodities are built from propylene molecules, and its conventional production technologies (naphtha steam cracking and fluid catalytic cracking) are unable to satisfy C₃H₆’s increasing requirements. In this scenario, Direct Propane Dehydrogenation (PDH) provides a practical and reliable route for supplying this short demand due to the economic availability of the raw material (C₃H₈) and the high propylene selectivities. The main challenges of propane dehydrogenation technology are related to the design of very active catalysts with negligible byproduct formation. In particular, the issue of catalyst deactivation by coke deposition still requires further development. In addition, PDH is a considerable endothermic reaction, and the efficiency of this technology is strictly related to heat transfer management. Thus, this current review specifically discusses the recent advances in highly dispersed bimetallic and trimetallic catalysts proposed for the PDH reaction in both conventional-heated and microwave-heated reactors. From the point of view of catalyst development, the recent research is mainly addressed to obtain nanometric and single-atom catalysts and core–shell alloys: atomically dispersed metal atoms promote the desorption of surface-bonded propylene and inhibit its further dehydrogenation. The discussion is focused on the alternative formulations proposed in the last few years, employing active species and supports different from the classical Pt-Sn/Al₂O₃ catalyst. Concerning the conventional route of energy-supply to the catalytic bed, the advantage of using a membrane as well as fluidized bed reactors is highlighted. Recent developments in alternative microwave-assisted dehydrogenation (PDH) employing innovative catalytic systems based on silicon carbide (SiC) facilitate selective heating of the catalyst. This advancement leads to improved catalytic activity and propylene selectivity while effectively reducing coke formation. Additionally, it promotes environmental sustainability in the ongoing electrification of chemical processes. Full article

This paper presents the results of a study on the characteristics of semiconductor sensors based on thin SnO₂ films modified with antimony, dysprosium, and silver impurities and dispersed double Pt/Pd catalysts deposited on the surface to detect carbon monoxide (CO). An original technology was developed, and ceramic targets were made from powders of Sn-Sb-O, Sn–Sb-Dy–O, and Sn–Sb-Dy-Ag–O systems synthesized by the sol–gel method. Films of complex composition were obtained by RF magnetron sputtering of the corresponding targets, followed by technological annealing at various temperatures. The morphology of the films, the elemental and chemical composition, and the electrical and gas-sensitive properties were studied. Special attention was paid to the effect of the film composition on the stability of sensor parameters during long-term tests under the influence of CO. It was found that different combinations of concentrations of antimony, dysprosium, and silver had a significant effect on the size and distribution of nanocrystallites, the porosity, and the defects of films. The mechanisms of degradation under prolonged exposure to CO were examined. It was established that Pt/Pd/SnO₂:0.5 at.% Sb film with optimal crystallite sizes and reduced porosity provided increased stability of carbon monoxide sensor parameters, and the response to the action of 100 ppm carbon monoxide was G₁/G₀ = 2–2.5. Full article

Constructing highly efficient catalysts for the degradation of organic pollutants driven by solar light in aquatic environments is a promising and green strategy. In this study, a novel hexagonal sheet-like Pt/SnS₂ heterojunction photocatalyst is successfully designed and fabricated using a hydrothermal method and photodeposition process for photocatalytic tetracycline (TC) degradation. The optimal Pt/SnS₂ hybrid behaves with excellent photocatalytic performance, with a degradation efficiency of 91.27% after 120 min, a reaction rate constant of 0.0187 min⁻¹, and durability, which can be attributed to (i) the formation of a metal/semiconductor interface field caused by loading Pt nanoparticles (NPs) on the surface of SnS₂, facilitating the separation of photo-induced charge carriers; (ii) the local surface plasmon resonance (LSPR) effect of Pt NPs, extending the light absorption range; and (iii) the sheet-like structure of SnS₂, which can shorten the transmission distance of charge carriers, thereby allowing more electrons (e⁻) and holes (h⁺) to transfer to the surface of the catalyst. This work provides new insights with the utilization of sheet-like structured materials for highly active photocatalytic TC degradation in wastewater treatment and environmental remediation. Full article

This study explores the application of Atomic Layer Deposition (ALD) to functionalize high-surface-area carbon supports with metal and metal oxide films and particles for applications in catalysis and electrocatalysis. The work reported here demonstrates that, through careful choice of precursors and absorption and reaction conditions, self-limited ALD growth on a high-surface-area carbon support can be achieved. Specific examples presented include the growth of conformal films of ZrO₂ and SnO₂ and the deposition of Ga₂O₃ and Pt particles on a carbon black support with a surface area of 250 m²·g⁻¹. A novel strategy for controlling the Pt weight loading and producing sub-nanometer Pt particles on a carbon support using a single ALD cycle is also presented. Full article

The measurement of cardiac troponin I (cTnI) is of vital importance for the early diagnosis of acute myocardial infarction. In this study, an enhanced electrochemiluminescent immunoassay for the highly sensitive and precise determination of cTnI was reported. A biomimetic chip with nepenthes peristome surface microstructures to achieve single-layer microbead arrays and integrated microelectrode arrays (MEAs) for ECL detection was microfabricated. Ru@SiO₂ nanoparticles were prepared as signal amplificators labeling immunomagnetic beads. Dendrimer-encapsulated platinum nanoparticles (Pt DENs) were electrochemically modified on ITO MEAs. The resulting Pt DEN-modified ITO MEAs preserved good optical transparency and exhibited an approximately 20-fold ECL signal amplification compared to that obtained from bare ITO. The method made full use of the biomimetic chip with Pt DENs to develop single-layer immunomagnetic bead arrays with increasingly catalyzed electrochemical oxidation of the [Ru(bpy)₃]²⁺–TPA system. Consequently, a limit of detection calculated as 0.38 pg/mL (S/N = 3) was obtained with excellent selectivity, demonstrating significant potential for the detection of cTnI in clinical diagnostics. Full article

Developing an OER electrocatalyst that balances high performance with low cost is crucial for widely adopting PEM water electrolyzers. Ru-based catalysts are gaining attention for their cost-effectiveness and high activity, positioning them as promising alternatives to Ir-based catalysts. However, Ru-based catalysts can be prone to oxidation at high potentials, compromising their durability. In this study, we utilize a simple synthesis method to synthesize a SnO₂, Nb₂O₅, and RuO₂ composite catalyst (SnO₂/Nb₂O₅@RuO₂) with multiple interfaces and abundant oxygen vacancies. The large surface area and numerous active sites of the SnO₂/Nb₂O₅@RuO₂ catalyst lead to outstanding acidic oxygen evolution reaction (OER) performance, achieving current densities of 10, 50, and 200 mA cm⁻² at ultralow overpotentials of 287, 359, and 534 mV, respectively, significantly surpassing commercial IrO₂. Moreover, incorporating Nb₂O₅ into the SnO₂/Nb₂O₅@RuO₂ alters the electronic structure at the interfaces and generates a high density of oxygen vacancies, markedly enhancing durability. Consequently, the membrane electrode composed of SnO₂/Nb₂O₅@RuO₂ and commercial Pt/C demonstrated stable operation in the PEM cell for 25 days at an industrial current density of 1 A cm⁻². This research presents a convenient approach for developing a highly efficient and durable Ru-based electrocatalyst, underscoring its potential for proton exchange membrane water electrolysis. Full article

Wearable sensors, specifically microneedle sensors based on electrochemical methods, have expanded extensively with recent technological advances. Today’s wearable electrochemical sensors present specific challenges: they show significant modulus disparities with skin tissue, implying possible discomfort in vivo, especially over extended wear periods or on sensitive skin areas. The sensors, primarily based on polyethylene terephthalate (PET) or polyimide (PI) substrates, might also cause pressure or unease during insertion due to the skin’s irregular deformation. To address these constraints, we developed an innovative, wearable, all-fiber-structured electrochemical sensor. Our composite sensor incorporates polyurethane (PU) fibers prepared via electrospinning as electrode substrates to achieve excellent adaptability. Electrospun PU nanofiber films with gold layers shaped via thermal evaporation are used as base electrodes with exemplary conductivity and electrochemical catalytic attributes. To achieve glucose monitoring, gold nanofibers functionalized by gold nanoflakes (AuNFs) and glucose oxidase (GOx) serve as the working electrode, while Pt nanofibers and Ag/AgCl nanofibers serve as the counter and reference electrode. The acrylamide-sodium alginate double-network hydrogel synthesized on electrospun PU fibers serves as the adhesive and substance-transferring layer between the electrodes. The all-fiber electrochemical sensor is assembled layer-by-layer to form a robust structure. Given the stretchability of PU nanofibers coupled with a high specific surface area, the manufactured porous microneedle glucose sensor exhibits enhanced stretchability, superior sensitivity at 31.94 μA (lg(mM))⁻¹ cm⁻², a broad detection range (1–30 mM), and a significantly low detection limit (1 mM, S/N = 3), as well as satisfactory biocompatibility. Therefore, the novel electrochemical microneedle design is well-suited for wearable or even implantable continuous monitoring applications, thereby showing promising significant potential within the global arena of wearable medical technology. Full article

Acetone is a biomarker found in the expired air of patients suffering from diabetes. Therefore, early and accurate detection of its concentration in the breath of such patients is extremely important. We prepared Tin(IV) oxide (SnO₂) nanospheres via hydrothermal treatment and then decorated them with bimetallic PtAu nanoparticles (NPs) employing the approach of in situ reduction. The topology, elemental composition, as well as crystal structure of the prepared materials were studied via field emission scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The findings revealed that bimetallic PtAu-decorated SnO₂ nanospheres (PtAu/SnO₂) were effectively synthesized as well as PtAu NPs evenly deposited onto the surface of the SnO₂ nanospheres. Pure SnO₂ nanospheres and PtAu/SnO₂ sensors were prepared, and their acetone gas sensitivity was explored. The findings demonstrated that in comparison to pristine SnO₂ nanosphere sensors, the sensors based on PtAu/SnO₂ displayed superior sensitivity to acetone of 0.166–100 ppm at 300 °C, providing a low theoretical limit of detection equal to 158 ppm. Moreover, the PtAu/SnO₂ sensors showed excellent gas response (R_a/R_g = 492.3 to 100 ppm), along with fast response and recovery (14 s/13 s to 10 ppm), good linearity of correlation, excellent repeatability, long-term stability, and satisfactory selectivity at 300 °C. This improved gas sensitivity was because of the electron sensitization of the Pt NPs, the chemical sensitization of the Au NPs, as well as the synergistic effects of bimetallic PtAu. The PtAu/SnO₂ sensors have considerable potential for the early diagnosis and screening of diabetes. Full article

(K_0.5Na_0.5)NbO₃-based single crystals are of interest as high-performance lead-free piezoelectric materials, but conventional crystal growth methods have some disadvantages such as the requirement for expensive Pt crucibles and difficulty in controlling the composition of the crystals. Recently, (K_0.5Na_0.5)NbO₃-based single crystals have been grown by the seed-free solid-state crystal growth method, which can avoid these problems. In the present work, 0.98(K_0.5Na_0.5)NbO₃–0.02(Bi_0.5Na_0.5)(Zr_0.85Sn_0.15)O₃ single crystals were grown by the seed-free solid-state crystal growth method. Sintering aids of 0.15 mol% Li₂CO₃ and 0.15 mol% Bi₂O₃ were added to promote single crystal growth. Pellets were sintered at 1150 °C for 15–50 h. Single crystals started to appear from 20 h. The single crystals grown for 50 h were studied in detail. Single crystal microstructure was studied by scanning electron microscopy of the as-grown surface and cross-section of the sample and revealed porosity in the crystals. Electron probe microanalysis indicated a slight reduction in K and Na content of a single crystal as compared to the nominal composition. X-ray diffraction shows that the single crystals contain mixed orthorhombic and tetragonal phases at room temperature. Raman scattering and impedance spectroscopy at different temperatures observed rhombohedral–orthorhombic, orthorhombic–tetragonal and tetragonal–cubic phase transitions. Polarization–electric field (P–E) hysteresis loops show that the single crystal is a normal ferroelectric material with a remanent polarization (P_r) of 18.5 μC/cm² and a coercive electrical field (E_c) of 10.7 kV/cm. A single crystal presents d₃₃ = 362 pC/N as measured by a d₃₃ meter. Such a single crystal with a large d₃₃ and high Curie temperature (~370 °C) can be a promising candidate for piezoelectric devices. Full article

Proton-exchange-membrane hydrogen fuel cells (PEMFCs) are an important energy device for achieving a sustainable hydrogen society. Carbon-based catalysts used in PEMFCs’ cathode can degrade significantly during operation-voltage shifts due to the carbon deterioration. The longer lifetime of the system is necessary for the further wide commercialization of PEMFCs. Therefore, carbon-free catalysts are required for PEMFCs. In this study, highly crystallized conducting Sb-doped SnO₂ (Sb-SnO₂) nanoparticles (smaller than 7 nm in size) were synthesized using an ozone-assisted hydrothermal synthesis. Pt nanoparticles were loaded on Sb-SnO₂ supporting particles by polyol method to be “Pt/Sb-SnO₂ catalyst”. The Pt/Sb-SnO₂ catalyst showed a high oxygen reduction reaction (ORR) mass activity (178.3 A g_-Pt⁻¹ @ 0.9 V), compared to Pt/C (149.3 A g_-Pt⁻¹ @ 0.9 V). In addition, the retention ratio from the initial value of electrochemical surface area (ECSA) during 100,000-voltage cycles tests between 1.0 V and 1.5 V, Pt/SnO₂ and Pt/Sb-SnO₂ catalyst exhibited higher stability (90% and 80%), respectively, than that of Pt/C catalyst (47%). Therefore, the SnO₂ and Sb-SnO₂ nanoparticles synthesized using this new ozone-assisted hydrothermal method are promising as carbon-free catalyst supports for PEMFCs. Full article

Increased demand for ethylene has motivated direct ethane dehydrogenation over Pt-based catalysts. PtSn/γ-Al₂O₃ and PtSnZnCa/γ-Al₂O₃ catalysts were investigated with the aim of understanding the effect of the pretreatment environment on the state of dispersed Pt for ethane dehydrogenation. The catalysts were prepared by the impregnation method and pretreated in different environments like static air (SA), flowing air (FA), and nitrogen (N₂) atmospheres. A comprehensive characterization of the catalysts was performed using Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), Temperature-Programmed Reduction (TPR), NH₃ Temperature-Programmed Desorption (NH₃-TPD), X-ray photoelectron spectroscopy (XPS), and Transmission Electron Microscopy (TEM) techniques. The results reveal that the PtSn on Al₂O₃ catalyst pretreated in the static air environment (PtSn-SA) exhibits 21% ethylene yield with 95% selectivity at 625 °C. XPS analysis found more platinum and tin on the catalyst surface after static air treatment. The overall acidity of the catalysts decreased after thermal treatment in static air. Elemental mapping demonstrated that Pt agglomeration was pronounced in catalysts calcined under flowing air and nitrogen. These factors are responsible for the enhanced activity of the PtSn-SA catalyst compared to the other catalysts. The addition of Zn and Ca to the PtSn catalysts increases the yield of the catalyst calcined in static air (PtSnZnCa-SA). The PtSnZnCa-SA catalyst showed the highest ethylene yield of 27% with 99% selectivity and highly stable activity at 625 °C for 10 h. Full article