Search Results (31)

Water scarcity poses a formidable challenge around the world, especially in arid regions where limited availability of freshwater resources threatens both human well-being and ecosystem sustainability. Membrane-based desalination technologies offer a viable solution to address this issue by providing access to clean water. This work ultimately aims to develop a novel permselective polymeric membrane material to be employed in an electrochemical desalination system. This part of the study addresses the optimization, preparation, and characterization of a polyvinylidene difluoride (PVDF) polymeric membrane using the electrospinning technique. The membranes produced in this work were fabricated under specific operational, environmental, and material parameters. Five different additives and nano-additives, i.e., graphene oxide (GO), carbon nanotubes (CNTs), zinc oxide (ZnO), activated carbon (AC), and a zeolitic imidazolate metal–organic framework (ZIF-8), were used to modify the functionality and selectivity of the prepared PVDF membranes. Each membrane was synthesized at two different levels of additive composition, i.e., 0.18 wt.% and 0.45 wt.% of the entire PVDF polymeric solution. The physiochemical properties of the prepared membranes were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), zeta potential, contact angle, conductivity, porosity, and pore size distribution. Based on findings of this study, PVDF/GO membrane exhibited superior results, with an electrical conductivity of 5.611 mS/cm, an average pore size of 2.086 µm, and a surface charge of −38.33 mV. Full article

Fibrous structure is a promising building block for developing high-performance wearable piezoresistive sensors. However, the inherent non-conductivity of the fibrous polymer remains a bottleneck for highly sensitive and fast-responsive piezoresistive sensors. Herein, we reported a polyaniline/reduced graphene oxide @ polydopamine/poly (vinylidene fluoride) (PANI/rGO@PDA/PVDF) nanofiber piezoresistive sensor (PNPS) capable of versatile wearable biomonitoring. The PNPS was fabricated by integrating rGO sheets and PANI particles into a PDA-modified PVDF nanofiber network, where PDA was implemented to boost the interaction between the nanofiber networks and functional materials, PANI particles were deposited on a nanofiber substrate to construct electroactive nanofibers, and rGO sheets were utilized to interconnect nanofibers to strengthen in-plane charge carrier transport. Benefitting from the synergistic effect of multi-dimensional electroactive materials in piezoresistive membranes, the as-fabricated PNPS exhibits a high sensitivity of 13.43 kPa⁻¹ and a fast response time of 9 ms, which are significantly superior to those without an rGO sheet. Additionally, a wide pressure detection range from 0 to 30 kPa and great mechanical reliability over 12,000 cycles were attained. Furthermore, the as-prepared PNPS demonstrated the capability to detect radial arterial pulses, subtle limb motions, and diverse respiratory patterns, highlighting its potential for wearable biomonitoring and healthcare assessment. Full article

Biofouling in membrane filtration systems poses significant operational challenges, leading to decreased permeate flux. The aim of this work was to study the anti-biofilm properties of new nanofiltration membranes produced via layer-by-layer, LBL, assembly by coating a polyvinylidene fluoride (PVDF) support with a polyethylenimine (PEI) and poly(acrylic acid)/graphene oxide (PAA-GO) mixture. The membranes were characterized according to contact angle, scanning electron microscopy (SEM), atomic force microscopy and their Z-potential. Biofilm quantification and characterization were carried out using crystal violet staining and SEM, while bacterial viability was assessed by using colony-forming units. The membrane with three bilayers ((PAA-PEI)₃/PVDF) showed a roughness of 77.78 nm. The incorporation of GO ((GO/PAA-PEI)₃/PVDF) produced a membrane with a smoother surface (roughness of 26.92 nm) and showed salt rejections of 16% and 68% for NaCl and Na₂SO₄, respectively. A significant reduction, ranging from 82.37 to 77.30%, in biofilm formation produced by S. aureus and E. coli were observed on modified membranes. Additionally, the bacterial viability on the modified membranes was markedly reduced (67.42–99.98%). Our results show that the modified membranes exhibited both antibiofilm and antimicrobial capacities, suggesting that these properties mainly depend on the properties of the modifying agents, as the initial adherence on the membrane surface was not totally suppressed, but the proliferation and formation of EPSs were prevented. Full article

Graphene oxide-silver poly(vinylidene fluoride) membranes (PVDF@GO-Ag) were successfully synthesized by the electrospinning method, which exhibited a high catalytic activity using the hydrogenation of 4-nitrophenol (4-NP) as a model reaction in a batch reaction study. The hybrid membranes doped with 1 wt% GO and 2 wt% Ag (PVDF-1-2) exhibited the most desired performance for the catalytic reduction of 4-NP. Importantly, PVDF-1-2 exhibited excellent cycling stability in 10 catalytic cycle tests and was highly amenable to separation. This property effectively addresses the significant challenges associated with the practical application of nanocatalysts. Furthermore, density-functional theory (DFT) calculations have demonstrated that the GO-Ag nanocomposites exhibit the strongest adsorption capacity for 4-NP⁻ when a specific ratio of GO and Ag is achieved, accompanied by the loading of Ag nanoclusters onto GO. Additionally, the study demonstrated that an increase in temperature significantly accelerated the reaction rate, in line with the van’t Hoff rule. This study provides an effective and environmentally friendly solution for the treatment of 4-NP in wastewater. Full article

Modern society and industrial development rely heavily on the availability of freshwater and minerals. Seawater reverse osmosis (SWRO) has been widely adopted for freshwater supply, although many questions have arisen about its environmental sustainability owing to the disposal of hypersaline rejected solutions (brine). This scenario has accelerated significant developments towards the hybridization of SWRO with membrane distillation–crystallization (MD-MCr), which can extract water and minerals from spent brine. Nevertheless, the substantial specific energy consumption associated with MD-MCr remains a significant limitation. In this work, energy harvesting was secured from renewables by hotspots embodied in the membranes, implementing the revolutionary approach of brine mining via photothermal membrane crystallization (PhMCr). This method employs self-heating nanostructured interfaces under solar radiation to enhance water evaporation, creating a carefully controlled supersaturated environment responsible for the extraction of minerals. Photothermal mixed matrix photothermal membranes (MMMs) were developed by incorporating graphene oxide (GO) or carbon black (CB) into polyvinylidene fluoride (PVDF) solubilized in an eco-friendly solvent (i.e., triethyl phosphate (TEP)). MMMs were prepared using non-solvent-induced phase separation (NIPS). The effect of GO or GB on the morphology of MMMs and the photothermal behavior was examined. Light-to-heat conversion was used in PhMCr experiments to facilitate the evaporation of water from the SWRO brine to supersaturation, leading to sodium chloride (NaCl) nucleation and crystallization. Overall, the results indicate exciting perspectives of PhMCr in brine valorization for a sustainable desalination industry. Full article

Nanoporous membranes (NPMBs) have been the focus of interest of many scientists in the last decade. However, the fouling phenomenon that takes place during the implantation period blocks pores and causes failure in the local implant. In this study, alumina NPMBs were developed using electrochemical anodization through two steps. Furthermore, graphene oxide (GO), free and impregnated with ZIF-8 MOF, was synthesized and loaded in a mixture of PVDF/PVP polymer matrix at different ratios, and was applied to the produced NPMBs using spin-coater. The NPMBs were characterized before and after coating by SEM/EDX, TEM, FTIR, XRD, contact angle and AFM. The antifouling features of the NPMBs were analyzed against two different bacterial species. The prepared alumina NPMBs demonstrated homogeneous porous structures with pore sizes ranging from 36 to 39 nm. The coated layers were proven to possess microporous coatings on the surfaces of the NPMBs. The numbers of released ions (Al and Zn) from the coated NPMBs were below the allowed limits. Bovine serum albumin (BSA) uptake in artificial cerebrospinal fluid (ACSF) was impressively reduced with the presence of coating materials. In addition, the antifouling behavior of the coated NPMBs against the selected strains of bacteria was greatly enhanced compared with the pure alumina NPMBs. Finally, NPMBs’ uncoated and polymer-coated membranes were tested for their ability to deliver donepezil HCl. The results reveal the downregulation of donepezil release, especially from NPMBs coated with PVDF/PVP 0.5GO. It is advised to use the current antifouling materials and techniques to overcome the limitations of the inorganic NPMBs implants. Full article

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer in which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-PNIPAAm polymer and graphene oxide (GO) were blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of NIPAAm to PVDF. PVDF-g-PNIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-PNIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and antifouling performance of the membrane without affecting the temperature response, thus extending the service life of the membrane. Full article

Membrane technology is an actively developing area of modern societies; with the help of high-performance membranes, it is possible to separate various mixtures for many industrial tasks. The objective of this study was to develop novel effective membranes based on poly(vinylidene fluoride) (PVDF) by its modification with various nanoparticles (TiO₂, Ag-TiO₂, GO-TiO₂, and MWCNT/TiO₂). Two types of membranes have been developed: dense membranes for pervaporation and porous membranes for ultrafiltration. The optimal content of nanoparticles in the PVDF matrix was selected: 0.3 wt% for porous membranes and 0.5 wt% for dense ones. The structural and physicochemical properties of the developed membranes were studied using FTIR spectroscopy, thermogravimetric analysis, scanning electron and atomic force microscopies, and measuring of contact angles. In addition, the molecular dynamics simulation of PVDF and the TiO₂ system was applied. The transport properties and cleaning ability under ultraviolet irradiation of porous membranes were studied by ultrafiltration of a bovine serum albumin solution. The transport properties of dense membranes were tested in pervaporation separation of a water/isopropanol mixture. It was found that membranes with the optimal transport properties are as follows: the dense membrane modified with 0.5 wt% GO-TiO₂ and the porous membrane modified with 0.3 wt% MWCNT/TiO₂ and Ag-TiO₂. Full article

Growing environmental concerns are stimulating researchers to develop more and more efficient materials for environmental remediation. Among them, polymer-based hierarchical structures, attained by properly combining certain starting components and processing techniques, represent an emerging trend in materials science and technology. In this work, graphene oxide (GO) and/or carbon nanotubes (CNTs) were integrated at different loading levels into poly (vinyl fluoride-co-hexafluoropropylene) (PVDF-co-HFP) and then electrospun to construct mats capable of treating water that is contaminated by methylene blue (MB). The materials, fully characterized from a morphological, physicochemical, and mechanical point of view, were proved to serve as membranes for vacuum-assisted dead-end membrane processes, relying on the synergy of two mechanisms, namely, pore sieving and adsorption. In particular, the nanocomposites containing 2 wt % of GO and CNTs gave the best performance, showing high flux (800 L × m⁻² h⁻¹) and excellent rejection (99%) and flux recovery ratios (93.3%), along with antifouling properties (irreversible and reversible fouling below 6% and 25%, respectively), and reusability. These outstanding outcomes were ascribed to the particular microstructure employed, which endowed polymeric membranes with high roughness, wettability, and mechanical robustness, these capabilities being imparted by the peculiar self-assembled network of GO and CNTs. Full article

This research demonstrates the preparation of composite membranes containing graphene oxide (GO) and investigates the separation mechanisms of various salts and bovine serum albumin (BSA) solutions. A microporous polyvinylidene fluoride–polyacrylic acid–GO (PVDF-PAA-GO) separation layer was fabricated on non-woven support. The GO-incorporating composite resulted in enlarged pore size (0.16 μm) compared with the control membrane (0.12 μm). The zeta potential of the GO composite was reduced to –31 from –19 mV. The resulting membranes with and without GO were examined for water permeability and rejection efficiency with single salt and BSA solutions. Using the non-woven/PVDF-PAA composite, the permeance values were 88–190 kg/m²hMPa, and the salt rejection coefficients were 9–28% for Na₂SO₄, MgCl₂, MgSO₄, and NaCl solutions. These salt removals were based on the Donnan exclusion mechanism considering the ion radii and membrane pore size. Incorporating GO into the separation layer exhibited limited impacts on the filtration of salt solutions, but significantly reduced BSA membrane adhesion and increased permeance. The negatively charged protein reached almost complete removal (98.4%) from the highly negatively charged GO-containing membrane. The GO additive improved the anti-fouling property of the composite membrane and enhanced BSA separation from the salt solution. Full article

In this study, PVDF/GO-h composite membranes were synthesised using a homogeniser to improve the dispersion of GO nanosheets within the composite membrane’s structure, and then characterised and contrasted to PVDF/GO-s control samples, which were synthesised via traditional blending method-implementing a magnetic stirrer. By characterizing membrane via X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), water contact angle (WCA) and membrane performance. SEM results showed that the number of the finger-like structure channels and pores in the sponge like structure of PVDF/GO-h composite membranes become more compared with PVDF/GO-s membranes. Water contact angle tests showed that the PVDF/GO-h composite membranes have lower contact angle than PVDF/GO-s control, which indicated the PVDF/GO-h composite membranes are more hydrophilic. Results also showed that composite membranes blended using homogeniser exhibited both improved water flux and rejection of target pollutants. In summary, it was shown that the performance of composite membranes could be improved significantly via homogenisation during synthesis, thus outlining the importance of further research into proper mixing. Full article

Mass loading of functional particles on the surface of nanofibers is the key to efficient heavy metal treatment. However, it is still difficult to prepare nanofibers with a large number of functional particle loads on the surface simply and efficiently, which hinders the further improvement of performance and increases the cost. Here, a new one-step strategy was developed to maximize the adhesion of graphene oxide (GO) particle to the surface of polyvinylidene fluoride (PVDF) nanofibers, which was combined with coaxial surface modification technology and blended electrospinning. The oxygen content on the as-prepared fiber surface increased from 0.44% to 9.32%, showing the maximized GO load. The increased adsorption sites and improved hydrophilicity greatly promoted the adsorption effect of Cr(VI). The adsorption capacity for Cr(VI) was 271 mg/g, and 99% removal rate could be achieved within 2 h for 20 mL Cr(VI) (100 mg/L), which was highly efficient. After five adsorption–desorption tests, the adsorption removal efficiency of the Cr(VI) maintained more than 80%, exhibiting excellent recycling performance. This simple method achieved maximum loading of functional particles on the fiber surface, realizing the efficient adsorption of heavy metal ions, which may promote the development of heavy-metal-polluted water treatment. Full article

Pristine and doped polyvinylidene fluoride (PVDF) are actively investigated for a broad range of applications in pressure sensing, energy harvesting, transducers, porous membranes, etc. There have been numerous reports on the improved piezoelectric and electric performance of PVDF-doped reduced graphene oxide (rGO) structures. However, the common in situ doping methods have proven to be expensive and less desirable. Furthermore, there is a lack of explicit extraction of the compression mode piezoelectric coefficient ($d_{33}$) in ex situ rGO doped PVDF composite films prepared using low-cost, solution-cast processes. In this work, we describe an optimal procedure for preparing high-quality pristine and nano-composite PVDF films using solution-casting and thermal poling. We then verify their electromechanical properties by rigorously characterizing $\beta$-phase concentration, crystallinity, piezoelectric coefficient, dielectric permittivity, and loss tangent. We also demonstrate a novel stationary atomic force microscope (AFM) technique designed to reduce non-piezoelectric influences on the extraction of $d_{33}$ in PVDF films. We then discuss the benefits of our $d_{33}$ measurements technique over commercially sourced piezometers and conventional piezoforce microscopy (PFM). Characterization outcomes from our in-house synthesized films demonstrate that the introduction of 0.3%w.t. rGO nanoparticles in a solution-cast only marginally changes the $\beta$-phase concentration from 83.7% to 81.7% and decreases the crystallinity from 42.4% to 37.3%, whereas doping increases the piezoelectric coefficient by 28% from $d_{33}$ = 45 pm/V to $d_{33}$ = 58 pm/V, while also improving the dielectric by 28%. The piezoelectric coefficients of our films were generally higher but comparable to other in situ prepared PVDF/rGO composite films, while the dielectric permittivity and $\beta$-phase concentrations were found to be lower. Full article

Membrane fouling markedly influences the service life and performance of the membrane during the using process. Herein, hydrophilic polyvinylidene fluoride (PVDF) nanocomposite (P-GO-DAA) membranes with antifouling and anti-biofouling characteristics were fabricated by employing graphene oxide (GO) and different concentrations of D-Tyrosine. The structural properties of the prepared nanocomposite membranes as well as pure PVDF membranes were characterized using FTIR, XPS, SEM, AFM, and contact angle analysis. It was found that the introduction of GO fillers made an excellent antifouling performance compared to pure PVDF indicated by the pure water flux, flux recovery rate, and rejection rate during ultrafiltration experiments as a result of the formation of the hydrophilic and more porous membrane. In particular, the nanocomposite membranes showed an increased flux of 305.27 L/(m²·h) and the rejection of 93.40% for the mixed pollutants solution (including Bull Serum Albumin, Sodium Alginate, and Humic Acid). Besides, the outstanding anti-biofouling activity was shown by the P-GO-DAA membrane with the properties of D-Tyrosine for inhibiting biofilm formation during the bacterial adhesion experiments. Furthermore, the adhesion ratio of bacteria on the membrane was 26.64% of the P-GO-DAA membrane compared to 84.22% of pure PVDF. These results were confirmed by CLSM. Full article

We used molecular dynamics to investigate the stability of graphene oxide (GO) layers supported on three polymeric materials, namely a polyvinylidene fluoride (PVDF), a pristine and a crosslinked polyamide–imide (PAI and PAI-cr). The membrane configurations consisted of a few layers of GO nanosheets stacked over the specified polymeric supports and submerged in water. We monitored the position, the tilt angle, and the radial distribution function of the individual GO nanosheets in respect to the plane of the supports. We showed that the outermost GO nanosheets were more distorted than those attached directly on the supports. The greatest distortion was observed for the GO nanosheets of the PVDF-supported system. Next, we recorded the density profiles of the water molecules across the distance from the layers to the polymer and discussed the hydrogen bonds between water hydrogens and the oxygen atoms of the GO functional groups. Full article