Search Results (60)

Mechanical failures frequently occur in On-Load Tap Changers (OLTCs) during operation, potentially compromising the reliability and stability of power systems. The goal of this study is to develop an intelligent and accurate diagnostic approach for OLTC mechanical fault identification, particularly under the challenge of non-stationary vibration signals. To achieve this, a novel hybrid method is proposed that integrates the Gazelle Optimization Algorithm (GOA), Feature Mode Decomposition (FMD), and a Transformer-based classification model. Specifically, GOA is employed to automatically optimize key FMD parameters, including the number of filters (K), filter length (L), and number of decomposition modes (N), enabling high-resolution signal decomposition. From the resulting intrinsic mode functions (IMFs), statistical time domain features—peak factor, impulse factor, waveform factor, and clearance factor—are extracted to form feature vectors. After feature extraction, the resulting vectors are utilized by a Transformer to classify fault types. Benchmark comparisons with other decomposition and learning approaches highlight the enhanced performance of the proposed framework. The model achieves a 95.83% classification accuracy on the test set and an average of 96.7% under five-fold cross-validation, demonstrating excellent accuracy and generalization. What distinguishes this research is its incorporation of a GOA–FMD and a Transformer-based attention mechanism for pattern recognition into a unified and efficient diagnostic framework. With its high effectiveness and adaptability, the proposed framework shows great promise for real-world applications in the smart fault monitoring of power systems. Full article

To enhance the operational stability of distribution networks during peak periods, this paper proposes a multi-timescale operational method considering load forecasting impacts. Firstly, the Crested Porcupine Optimizer (CPO) is employed to optimize the hyperparameters of long short-term memory (LSTM) networks for an accurate prediction of the next-day load curves. Building on this foundation, a multi-timescale optimization strategy is developed: During the day-ahead operation phase, a conservation voltage reduction (CVR)-based regulation plan is formulated to coordinate the control of on-load tap changers (OLTCs) and distributed resources, alleviating peak-shaving pressure on the upstream grid. In the intraday optimization phase, real-time adjustments of OLTC tap positions are implemented to address potential voltage violations, accompanied by an electrical distance-based control strategy for flexible adjustable resources, enabling rapid voltage recovery and enhancing system stability and robustness. Finally, a modified IEEE-33 node system is adopted to verify the effectiveness of the proposed multi-timescale operational method. The method demonstrates a load forecasting accuracy of 93.22%, achieves a reduction of 1.906% in load power demand, and enables timely voltage regulation during intraday limit violations, effectively maintaining grid operational stability. Full article

The proactive involvement of photovoltaic (PV) smart inverters (PVSIs) in grid management facilitates voltage regulation and enhances the integration of distributed energy resources (DERs) within distribution networks. However, to fully exploit the capabilities of PVSIs, it is essential to achieve optimal control of their operations and effective coordination with voltage-regulating devices in the distribution network. This study developed a dual strategy approach to forecast the optimal setpoints of onload tap changers (OLTCs), PVSIs, and distribution static synchronous compensators (DSTATCOMs) to improve the voltage profiles in power distribution systems. The study began by running a centralized AC optimal power flow (CACOPF) and using the hourly PV output power and the load demand to determine the optimal active and reactive power of the PVSIs, the setpoint of the DSTATCOM, and the optimal tap setting of the OLTC. Furthermore, Machine Learning (ML) models were trained as controllers to determine the reactive-power setpoints for the PVSIs and DSTATCOMs as well as the optimal OLTC tap position required for voltage stability in the network. To assess the effectiveness of the method, comprehensive evaluations were carried out on a modified IEEE 33 bus with a high penetration of PV energy. The results showed that deep neural networks (DNNs) outperformed other ML models used to mimic the coordination method based on CACOPF. Furthermore, when the DNN-based controller was tested and compared with the optimizer approach under different loading and PV conditions, the DNN-based controller was found to outperform the optimizer in terms of computational time. This approach allows predictive control in power systems, helping system operators determine the action to be initiated under uncertain PV energy and loading conditions. The approach also addresses the computational inefficiency arising from contingencies in the power system that may occur when optimal power flow (OPF) is run multiple times. Full article

Accurate mechanical fault diagnosis of On-Load Tap Changers (OLTCs) remains crucial for power system reliability yet faces challenges from vibration signals’ non-stationary characteristics and limitations of conventional methods. This paper develops a hybrid framework combining metaheuristic-optimized decomposition with hierarchical temporal learning. The methodology employs a Subtraction-Average-Based Optimizer (SABO) to adaptively configure Time-Varying Filtered Empirical Mode Decomposition (TVFEMD), effectively resolving mode mixing through optimized parameter selection. The decomposed components undergo dual-stage temporal processing: A Temporal Convolutional Network (TCN) extracts multi-scale dependencies via dilated convolution architecture, followed by Gated Recurrent Unit (GRU) layers capturing dynamic temporal patterns. An experimental platform was established using a KM-type OLTC to acquire vibration signals under typical mechanical faults, subsequently constructing the dataset. Experimental validation demonstrates superior classification accuracy compared to conventional decomposition–classification approaches in distinguishing complex mechanical anomalies, achieving a classification accuracy of 96.38%. The framework achieves significant accuracy improvement over baseline methods while maintaining computational efficiency, validated through comprehensive mechanical fault simulations. This parameter-adaptive methodology demonstrates enhanced stability in signal decomposition and improved temporal feature discernment, proving particularly effective in handling non-stationary vibration signals under real operational conditions. The results establish practical viability for industrial condition monitoring applications through robust feature extraction and reliable fault pattern recognition. Full article

With the increasing penetration of distributed photovoltaics (PVs) in distribution networks (DNs), issues like voltage violations and fluctuations are becoming more prominent. This paper proposes a spatio-temporal adaptive voltage coordination control strategy involving multiple timescales and multi-device collaboration. Aiming at the heavy workload caused by the continuous sampling of real-time data in the whole domain, an intra-day innovative construction of intra-day minute-level optimization and real-time adaptive control double-layer control mode are introduced. Intra-day minute-level refinement of on-load tap changer (OLTC) and step voltage regulator (SVR) day-ahead scheduling plans to fully utilize OLTC and SVR voltage regulation capabilities and improve voltage quality is discussed. In real-time adaptive control, a regional autonomy mechanism based on the functional area voltage quality risk prognostication coefficient (VQRPC) is innovatively proposed, where each functional area intelligently selects the time period for real-time voltage regulation of distributed battery energy storage systems (DESSs) based on VQRPC value, in order to improve real-time voltage quality while reducing the data sampling workload. Aiming at the state of charge (SOC) management of DESS, a novel functional area DESS available capacity management mechanism is proposed to coordinate DESS output and improve SOC homogenization through dynamically updated power–capacity availability (PCA). And vine model threshold band (VMTB) and deviation optimization management (DOM) strategies based on functional area are innovatively proposed, where DOM optimizes DESS output through the VMTB to achieve voltage fluctuation suppression while optimizing DESS available capacity. Finally, the DESS and electric vehicle (EV) cooperative voltage regulation mechanism is constructed to optimize DESS capacity allocation, and the black-winged kite algorithm (BKA) is used to manage DESS output. The results of a simulation on a modified IEEE 33 system show that the proposed strategy reduces the voltage fluctuation rate of each functional area by an average of 36.49%, reduces the amount of data collection by an average of 68.31%, and increases the available capacity of DESS by 5.8%, under the premise of a 100% voltage qualification rate. Full article

Optimizing the operation of active distribution networks (ADNs) has become more challenging because of the uncertainty created by the high penetration level of distributed photovoltaic (PV). From the convex optimization perspective, this paper proposes a two-layer optimization model to simplify the solution of the ADN optimal operation problem. Firstly, to pick out the ADN “key” nodes, a “key” nodes selection approach that used improved K-means clustering algorithm and two indexes (integrated voltage sensitivity and reactive power-balance degree) is introduced. Then, a two-layer ADN optimization model is built using various time scales. The upper layer is a long-time-scale model with on-load tap-changer transformer (OLTC) and capacitor bank (CB), and the lower layer is a short-time-scale optimization model with PV inverters and distributed energy storages (ESs). To take into account the PV users’ interests, maximizing PV active power output is added to the objective. Afterwards, under the application of the second-order cone programming (SOCP) power-flow model, a linearization method of OLTC model and its tap change frequency constraints are proposed. The linear OLTC model, together with the linear models of the other equipment, constructs a mixed-integer second-order cone convex optimization (MISOCP) model. Finally, the effectiveness of the proposed method is verified by solving the IEEE33 node system using the CPLEX solver. Full article

This paper proposes an optimal control method for the on-load tap changer (OLTC) of a substation’s main transformer (M.TR), to maximize the voltage compliance rate (VCR) in distribution system feeders. The conventional auto voltage regulator (AVR)’s line-drop compensation (LDC) control method struggles with accurately determining load centers and has limitations in managing voltage due to the variability of distributed energy resources (DERs). To address these challenges, this study defines sample number-based VCR (SNB-VCR) as the performance index function to be maximized. The optimal tap positions for the OLTC are obtained using the gradient ascent method. Since the SNB-VCR evaluates voltage compliance using 15 min interval data collected from all the load and DER connection points in the distribution system, the tap position obtained by the gradient ascent method maximizes voltage quality for every feeder included in the system. Using a simulation, it is verified that the proposed tap control method improves the overall voltage quality and reduces the occurrence of overvoltage or undervoltage compared to LDC control. The proposed control strategy offers a practical solution for enhancing voltage management efficiency in modern distribution systems, particularly those with high penetration of DERs. Full article

As the penetration of distributed renewable energy increases, the phenomenon of bidirectional power flow in distribution networks becomes increasingly severe. Traditional regulation devices like OLTC (on-load tap changer) and CB (capacitor bank) cannot effectively mitigate reverse power flow in distribution networks due to their limitations. The transmission capacity of the distribution network under reverse power flow is approximately 50% of the rated capacity of the OLTC, leading to issues such as voltage limit violations and high wind and solar curtailment rates. This paper proposes a method for calculating the reverse power flow delivery capacity of distribution networks, quantitatively describing the distribution network’s delivery limits for reverse power flow. Based on this, a joint optimization model for multiple distribution networks with an SOP is established. The SOP is utilized to share reverse power flow delivery capacity among multiple distribution networks, enhancing operational economy and increasing the accommodation of the DG. Finally, the method’s effectiveness and correctness are verified in the IEEE 33-node system. The results validate that while joint operation does not enhance the reverse flow transmission capacity of a single distribution network, it can, through the shared reverse flow transmission capacity approach, elevate the reverse flow transmission capacity to approximately 70% during the majority of time periods. Full article

Unlike traditional tap changers, which require transformers to be de-energized before making changes, On-Load Tap Changers (OLTCs) can adjust taps while the transformer is in service, ensuring continuous power supply during voltage regulation. OLTCs enhance grid reliability and support load balancing, reducing strain on the network and optimizing power quality. Their importance has grown as the demand for stable voltage and the integration of renewables has increased, making them vital for modern and resilient power systems. While enhanced OLTCs often incorporate stronger materials and improved designs, mechanical components like contacts and diverter switches can still experience wear over time. This can result in longer maintenance intervals. In the era of digitalization, advanced diagnostic techniques capable of detecting early signs of wear or malfunction are essential to enable preventive maintenance for these important components. This contribution introduces a novel method for detecting faults and irregularities in OLTCs, leveraging vibroacoustic signals to enhance OLTC diagnostics. This paper proposes a tolerance-based approach using the envelope of vibroacoustic signals to identify faults. A significant challenge in this field is the limited availability of faulty signal data, which hinders the performance of machine learning algorithms. To address this, this study introduces a nonlinear model utilizing amplitude modulation with a Gaussian carrier to simulate faults by introducing controlled distortions. The dataset used in this study, with data recorded under real operating conditions from 2016 to 2023, is free of anomalies, providing a robust foundation for the analysis. The results demonstrate a marked improvement in the robustness of detecting simulated faults, offering a promising solution for enhancing OLTC diagnostics and preventive maintenance in modern power systems. Full article

With the proposal of the dual carbon target, the distributed photovoltaic (PV) industry has rapidly developed in recent years. However, the randomness and volatility of photovoltaic energy can be transmitted to the main grid through distribution network substations, posing challenges to the stable operation of the power system. Therefore, this paper considers tapping into the regulation potential of feeder loads on the distribution network side, as well as distributed energy storage and distributed PV resources, to enhance the grid’s control methods. A power fluctuation smoothing control strategy for substations in distribution networks, accounting for multiple types of regulation resources, is proposed. In the day-ahead stage, traditional voltage regulation devices such as the OLTC (on-load tap changer) and CB (circuit breaker) are pre-dispatched based on source–load forecasts, optimizing the fluctuation range of substation power and the number of device operations. This provides optimal substation power values for day-to-day optimization. During the intraday phase, fast regulation devices such as PV (photovoltaic), SVC (static var compensator), and energy storage systems are coordinated, and an optimization model is established with the goal of reducing power curtailment while closely tracking substation trends. This model quickly calculates the active power regulation and device operations of various adjustable resources, improving the economic efficiency of the distribution network system while achieving power fluctuation smoothing at the substation level. Finally, the feasibility and effectiveness of the power fluctuation smoothing control model are verified through simulations on an improved standard distribution system. Full article

The paper proposes a new local method of controlling the on-load tap changer (OLTC) of a transformer to mitigate negative voltage phenomena in low-voltage (LV) networks with a high penetration of photovoltaic (PV) installations. The essence of the method is the use of the load compensation (LC) function with settings determined via artificial neural network (ANN) algorithms. The proposed method was compared with other selected local methods recommended in European regulations, in particular with those currently required by Polish distribution system operators (DSOs). Comparative studies were performed using the model of the 116-bus IEEE test network, taking into account the unbalance in the network and the voltage variation on the medium voltage (MV) side. Full article

During the voltage regulation of on-load tap changers (OLTCs), the movement of the contacts can easily cause arcing, which may lead to erosion or malfunction. To reduce the energy and probability of arcing, we focus on designing an optimal range for the sliding speed and contact pressure of the contacts to minimize arc energy. Initially, our research introduces a novel OLTC arc testing platform to simulate the motion of static and dynamic contacts, exploring the relationship between different sliding speeds, contact pressures, and factors like arc voltage waveform, arcing rate, arc resistance, and arc energy. Subsequently, by employing multiple nonlinear regression methods, we establish functional relationships between sliding speed and arc energy, as well as contact pressure and arc energy, evaluating the fit using correlation coefficients. Finally, through analyzing their nonlinear behaviors, we determine the ideal sliding speed and contact pressure. The results indicate that when the OLTC contacts slide at an optimal speed between 89 and 103 mm/s and optimal contact pressure between 1.5 and 1.7 N, the arc energy can be minimized, thereby enhancing the performance and lifespan of the on-load tap changer. This study offers feasible insights for the design and operation of OLTCs, aiding in the improvement of power system regulation. Full article

In engineering applications, the accuracy of on-load tap changer (OLTC) mechanical fault identification methods based on vibration signals is constrained by the quantity and quality of the samples. Therefore, a novel small-sample-size OLTC mechanical fault identification method incorporating short-time Fourier transform (STFT), synchrosqueezed wavelet transform (SWT), a dual-stream convolutional neural network (DSCNN), and support vector machine (SVM) is proposed. Firstly, the one-dimensional time-series vibration signals are transformed using STFT and SWT to obtain time–frequency graphs. STFT time–frequency graphs capture the global features of the OLTC vibration signals, while SWT time–frequency graphs capture the local features of the OLTC vibration signals. Secondly, these time–frequency graphs are input into the CNN to extract key features. In the fusion layer, the feature vectors from the STFT and SWT graphs are combined to form a fusion vector that encompasses both global and local time–frequency features. Finally, the softmax classifier of the traditional CNN is replaced with an SVM classifier, and the fusion vector is input into this classifier. Compared to the traditional fault identification methods, the proposed method demonstrates higher identification accuracy and stronger generalization ability under the conditions of small sample sizes and noise interference. Full article

The On-Load Tap Changer (OLTC) is the only movable mechanical component in a converter transformer. To ensure the reliable operation of the OLTC and to promptly detect mechanical faults in OLTCs to prevent them from developing into electrical faults, this paper proposes a fault diagnosis method for OLTCs based on a combination of Particle Swarm Optimization (PSO) algorithm and Least Squares Support Vector Machine (LSSVM) with multi-feature fusion. Firstly, a multi-feature extraction method based on time/frequency domain statistics, synchrosqueezed wavelet transform, singular value decomposition, and multi-scale modal decomposition is proposed. Meanwhile, the random forest algorithm is used to screen features to eliminate the influence of redundant features on the accuracy of fault diagnosis. Secondly, the PSO algorithm is introduced to optimize the hyperparameters of LSSVM to obtain optimal parameters, thereby constructing an optimal LSSVM fault diagnosis model. Finally, different types of feature combinations are utilized for fault diagnosis, and the impact of these feature combinations on the fault diagnosis results is compared. Experimental results indicate that features of different types can complement each other, making the OLTC state information carried by multi-dimensional features more comprehensive, which helps to improve the accuracy of fault diagnosis. Compared with four traditional fault diagnosis methods, the proposed method performs better in fault diagnosis accuracy, achieving the highest accuracy of 98.58%, which can help to detect mechanical faults in the OLTC early and reduce the system’s downtime. Full article

A new energy industry represented by photovoltaic and wind power has been developing rapidly in recent years, and its randomness and volatility will impact the stable operation of the power system. At present, it is proposed to enrich the regulation of the power grid by tapping the regulation potential of load-side resources. This paper evaluates the overall voltage regulation capability of substations under the premise of considering the impact on network voltage security and providing a theoretical basis for the participation of load-side resources of distribution networks in the regulation of the power grid. This paper proposes a Zbus linear power flow model based on Fixed-Point Power Iteration (FFPI) to enhance power flow analysis efficiency and resolve voltage sensitivity expression. Establishing the linear relationship between the voltages of PQ nodes, the voltage of the reference node, and the load power, this paper clarifies the impact of reactive power compensation devices and OLTC (on-load tap changer) tap changes on the voltages of various nodes along the feeder. It provides theoretical support for evaluating the voltage regulation range for substations. The day-ahead focus is on minimizing network losses by pre-optimizing OLTC tap positions, calculating the substation voltage regulation boundaries within the day, and simultaneously optimizing the total reactive power compensation across the entire network. By analyzing the calculated examples, it was found that a pre-scheduled OLTC (on-load tap changer) can effectively reduce network losses in the distribution grid. Compared with traditional methods, the voltage regulation range assessment method proposed in this paper can optimize the adjustment of reactive power compensation devices while ensuring the voltage safety of all nodes in the network. Full article