Search Results (108)

A ceramic–metal composite was synthesized using sol–gel and electrospinning methods to serve as a SERS substrate. The precursors used were tetraethyl orthosilicate, aluminum nitrate, and zirconium, and polyvinylpyrrolidone was added to electrospun nonwoven fibrous membranes. The membranes were sintered, decorated with silver nanoparticles. The enhancement substrates were made of fibers of cylindric morphology with an average diameter of approximately 190 nm, a smooth surface, and 9 nm spherical particles decorating the surface of the fibers. The enhancement capacity of the substrates was tested using pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at different concentrations with Raman spectroscopy to determine whether the size and complexity of the analyte has an impact on the enhancement capacity. Enhancement factors of 2.53 × 10², 3.06 × 10¹, 2.97 × 10³, 4.66 × 10³, and 1.45 × 10³ times were obtained for the signal of pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at concentrations of 1 nM. Full article

This study investigates the influence of divalent metals—(Mg(II), Co(II), and Ni(II)) in layered double hydroxides (LDHs), with a constant trivalent Fe(III) component—on the decoloration of crystal violet and methyl blue dyes via a Fenton-type oxidation reaction. The catalysts, synthesized by co-precipitation and hydrothermal treatment, were tested in both hydroxide and oxide forms under varying agitation conditions (0 and 280 rpm). A 2² × 3 factorial design was used to analyze the effect of the divalent metal type, catalyst phase, and stirring. The Mg/Fe oxide, with the highest BET surface area (144 m²/g) and crystallite size (59.7 nm), showed superior performance—achieving up to 98% decoloration of crystal violet and 97% of methyl blue within 1 h. The kinetic analysis revealed pseudo-second-order and pseudo-first-order fits for crystal violet and methyl blue, respectively. These findings suggest that LDH-based catalysts provide a fast, low-cost, and effective option for dye removal in aqueous systems. Full article

This study focuses on investigating the stability of modern and contemporary paints based on manganese violet pigment PV16 (NH₄MnP₂O₇) when exposed to atmospheric pollutants, specifically sulfur dioxide (SO₂) in the presence of high relative humidity. In particular, this study aims to investigate the role of PV16 in increasing the degradation processes of various modern binders. Therefore, the objectives of this research can be divided into (i) evaluating the chemical modifications involving PV16, (ii) investigating the degradation processes that occur in different organic matrices (i.e., drying oil, alkyd resin, and acrylic and styrene–acrylic emulsions), and (iii) comparing the chemical stability of model and commercial paints. The paints were analyzed by 3D Optical Microscopy, Attenuated total Reflection–Fourier-Transform Infrared spectroscopy (ATR-FTIR) and μ-Raman Spectroscopy, Scanning Electron Microscope coupled with Energy Dispersive X-Ray spectroscopy (SEM-EDX), X-Ray Powder Diffraction (XRPD), Fiber Optic Reflectance Spectroscopy (FORS), Pyrolysis–Gas Chromatography–Mass Spectrometry (Py-GC/MS), and Thermally assisted Hydrolysis and Methylation (THM) of Py-GC/MS (THM-Py-GC/MS). The results show that when exposed to high relative humidity and SO₂, PV16 presents a colorimetric change from violet to grey; several compounds crystallize on the surface; and, depending on the binder, various degradation reactions occur. This study highlights the susceptibility of manganese violet pigment PV16 under certain environmental conditions, which may be considered to define adequate conservation strategies for works of art containing this specific pigment. Additionally, the results obtained within this investigation point out the need to expand the chemical knowledge of this material for engineering, sensing, and industrial applications. Full article

A new type of CeO₂-modified AgCl catalyst (CeO₂/AgCl) was prepared by a one-step method, which efficiently inhibits the recombination of photogenerated carriers. During the visible-light degradation process, this catalyst exhibited excellent and stable performance. It could not only effectively degrade rhodamine B (RhB), methyl orange (MO) and crystal violet (CV) but also maintain excellent activity under different environmental conditions. In the RhB degradation experiment in particular, the CeO₂/AgCl-30 composite with the optimal proportion had a degradation rate 5.43 times that of pure AgCl in the seawater system and 9.17 times that of pure AgCl in the deionized water condition, while also showing excellent stability. Through characterization tests such as XRD, XPS and ESR, its crystal structure, elemental composition and so on were analyzed. Based on the characterization results, the CeO₂/AgCl composite showed a relatively wide light absorption range and a relatively high photo-induced charge separation efficiency. Meanwhile, it was inferred that the main active species in the reaction process were ·O₂⁻ and ·OH. Finally, based on its electronic band structure, an S-scheme heterojunction structure was proposed. Full article

Introduction: Antimicrobial resistance is a global threat, highlighting the urgent need for novel antimicrobial agents. Among the mechanisms of resistance, bacteria can release drug-degrading enzymes and express efflux pumps, as well as grow in protected aggregates known as biofilms. Pseudomonas aeruginosa and Staphylococcus aureus are among the most prevalent biofilm infections in chronic wounds, respiratory and urinary tract infections, and device-associated infections. Pseudocyphellaria faveolata (Delise) Malme is a lichen with metabolites with unexplored antimicrobial potential. Aims: To identify and characterize the major metabolites present in Pseudocyphellaria Faveolata and to determine their antimicrobial activity against Staphylococcus aureus and Pseudomonas aeruginosa. Methods: The molecules were purified by column chromatography and characterized by NMR spectroscopy. The antimicrobial activity of the compounds was determined in terms of proliferation, adhesion, and viability against P. aeruginosa and S. aureus by the broth microdilution method and crystal violet staining. Viability was determined by the resazurin reduction assay on normal human fibroblasts to determine cytotoxicity over human cells. Results: The major metabolites were spectroscopically characterized and identified as physciosporin and methyl virensate. Physciosporin showed antimicrobial activity on S. aureus, with a MIC of 32 μg/mL and MBC of 128 μg/mL, and prevented biofilm formation from 16 μg/mL. Methyl virensate also had antimicrobial activity on S. aureus (MIC = 64 μg/mL). None of these metabolites significantly affected P. aeruginosa proliferation, viability, or adhesion. Cytotoxicity of physciosporin at 16 ug/mL on normal human fibroblasts was below 20%. Conclusions: This is the first report on the study of the antimicrobial activity of these compounds. Physciosporin showed promising activity in preventing the formation of S. aureus biofilms, which are responsible for chronic infections. These findings provide a foundation for exploring the antimicrobial potential of other lichenic depsidones. Full article

We present structural, morphological, optical and photocatalytic properties of multiferroic Bi_0.98Ba_0.02FeO₃ (BBFO2) perovskite thin films prepared by a combined sol–gel and spin-coating method. X-ray diffraction (XRD) analysis revealed that all the perovskite films consisted of the stable polycrystalline rhombohedral phase structure (space group R3c) with a tolerance factor of 0.892. By using Rietveld refinement of diffractogram XRD data, crystallographic parameters, such as bond angle, bond length, atom position, unit cell parameters, and electron density measurements were computed. Scanning electron microscopy (SEM) allowed us to assess the homogeneous and smooth surface morphology of the films with a small degree of porosity, while chemical surface composition characterization by X-ray photoelectron spectroscopy (XPS) showed the presence of Bi, Fe, O and the doping element Ba. Absorption measurements allowed us to determine the energy band gap of the films, while photoluminescence measurements have shown the presence of oxygen vacancies, which are responsible for the enhanced photocatalytic activity of the material. Photocatalytic degradation experiments of Methylene Blue (MB), Methyl orange (MO), orange G (OG), Violet and Rhodamine B (RhB) performed on top of BBFO2 thin films under solar light showed the degradation of all pollutants in varying discoloration efficiencies, ranging from 81% (RhB) to 54% (OG), 53% (Violet), 47% (MO) and 43% (MB). Full article

Graphene materials and their derivatives have shown promising capabilities in removing anionic and cationic dyes from wastewater. The present study aims at the synthesis of graphene-based material with a high specific surface area and evaluates its use as an adsorbent for removing toluidine blue and methyl violet from aqueous solutions. The physicochemical characterization of the adsorbent before and after dye adsorption is made by XRD, Raman spectroscopy, SEM, TEM, nitrogen physisorption, TG-DTA, and XPS. The influence of the solution’s pH, contact time, dye concentration, and temperature on the adsorption efficiency is investigated. The adsorbent demonstrated high adsorption capacity towards toluidine blue (265.2 mg.g⁻¹) and methyl violet (200.4 mg.g⁻¹) dyes from water. The adsorption process for both dyes follows the Langmuir model and involves physical rather than chemical interactions. Kinetic parameters were also determined. The adsorption of the studied cationic dyes can be attributed to a combination of mechanisms, including electrostatic interactions, hydrogen bonding, and π-π interactions between the dye molecules and the aromatic structure of reduced graphene oxide. The findings in the present work highlight the possibilities for enhancing graphene-based materials’ adsorption capabilities. Full article

The dyes used to produce two Palestinian garments from the British Museum’s collection attributed to the late 19th–early 20th century were investigated by high pressure liquid chromatography coupled with diode array detector and tandem mass spectrometry (HPLC-DAD-MS/MS). Palestinian embroidery is a symbol of national identity and the topic of scholarly research. However, little attention has been given to the dyes and how these changed with the introduction of new synthetic formulations in the second half of the 19th century. The results revealed the use of natural indigoid blue and red madder (Rubia tinctorum), in combination with tannins. Yellow from buckthorn (probably Rhamnus saxatilis) and red from cochineal (probably Dactylopius coccus) were found mixed with synthetic dyes in green and dark red embroidery threads, respectively. Early synthetic dyes were identified in all the other colours. These include Rhodamine B (C.I. 45170), Orange II (C.I. 15510), Orange IV (C.I. 13080), Metanil Yellow (C.I. 13065), Chrysoidine R (C.I. 11320), Methyl Violet (C.I. 42535), Malachite Green (C.I. 42000), Fuchsin (C.I. 42510), Auramine O (C.I. 41000) and Methyl Blue (C.I. 42780). As the date of the first synthesis of these dyes is known, the production date of the garments was refined, suggesting that these were likely to be produced towards the end of the 1880s/beginning of the 1890s. The continuous use of historical local sources of natural dyes, alongside new synthetic dyes, is of particular interest, adding rightful nuances to the development of textile-making practices in this region. Full article

This study is the first to convert two waste materials, waste rice noodles (WRN) and red mud (RM), into a low-cost, high-value magnetic photocatalytic composite. WRN was processed via a hydrothermal method to produce a solution containing carbon quantum dots (CQDs). Simultaneously, RM was dissolved in acid to form a Fe³⁺ ion-rich solution, which was subsequently mixed with the CQDs solution and underwent hydrothermal treatment. During this process, the Fe³⁺ ions in RM were transformed into the maghemite (γ-Fe₂O₃) phase, while CQDs were incorporated onto the γ-Fe₂O₃ surface, resulting in the CQDs/γ-Fe₂O₃ magnetic photocatalytic composite. Experimental results demonstrated that the WRN-derived CQDs not only facilitated the formation of the magnetic γ-Fe₂O₃ phase but also promoted a synergistic interaction between CQDs and γ-Fe₂O₃, enhancing electron-hole pair separation and boosting the production of reactive radicals such as O₂^·− and ·OH. Under optimized conditions (pH = 8, carbon loading: 10 wt%), the CQDs/γ-Fe₂O₃ composite exhibited good photocatalytic performance against methylene blue, achieving a 97.6% degradation rate within 480 min and a degradation rate constant of 5.99 × 10⁻³ min⁻¹, significantly outperforming RM and commercial γ-Fe₂O₃ powder. Beyond methylene blue, this composite also effectively degraded common organic dyes, including malachite green, methyl violet, basic fuchsin, and rhodamine B, with particularly high efficiency against malachite green, reaching a degradation rate constant of 5.465 × 10⁻² min⁻¹. Additionally, due to its soft magnetic properties (saturation magnetization intensity: 16.7 emu/g, residual magnetization intensity: 2.2 emu/g), the material could be conveniently recovered and reused after photocatalytic cycles. Even after 10 cycles, it retained over 98% recovery and 96% photocatalytic degradation efficiency, underscoring its potential for cost-effective, large-scale photocatalytic water purification. Full article

Cyclodextrins (CDs) are natural cyclic oligosaccharides with the ability to form inclusion complexes with various organic substances. In this paper, we investigate the potential of CD complex formation to enhance the antibacterial activity and antioxidant properties of poorly soluble bioactive agents, such as chalcones, chromenes, stilbenoids and xanthylium derivatives, serving as potential adjuvants, in comparison with standard antiseptics. The interaction of these bioactive agents with the hydrophobic pocket of methyl-β-cyclodextrin (MCD) was confirmed using spectroscopic methods such as UV-vis, FTIR, ¹H and ¹³C NMR, mass-spectrometry. CD-based delivery system allows for combining multiple active agents, improving solubility, antibacterial efficacy by enhancing penetration into target bacterial cells (E. coli selectivity demonstrated via confocal microscopy). Novel compounds of chalcones and stilbenoids derivatives additionally enhance efficacy by inhibiting bacterial efflux pumps, increasing membrane permeability, and inhibiting bacterial enzymes, and showed a synergy when used in combination with metronidazole. The intricate relationship between the structural characteristics and functional properties of chalcones and stilbenoids in terms of their antibacterial and antioxidative capabilities is revealed. The substituents within aromatic rings significantly influence this activity, where position of electron-donating methoxy groups playing a crucial role. Among chalcones, stilbenoids, ana xanthyliums, the compounds caring a benzodioxol ring, analogous to natural bioactive compounds like apiol, dillapiol, and myristicin, emerge as prominent antibacterial activity. To explore the possibility to create theranostic formulations, we used fluorescent markers to visualize target cells, antiseptics to provide antibacterial activity, and bioactive agents as chalcones acting as adjuvants. Additionally, new antioxidant compounds were found such as Xanthylium derivative (R351) and chromene derivative: 1-methyl-3-(2-amino-3-cyano-7-methoxychromene-4-yl)-pyridinium methanesulfate: the pronounced antioxidant properties of these substances are observed comparable to quercetin in the efficiency. Rhodamine 6G, gentian violet, and Congo Red exhibit good antioxidant properties, although their activity is an order of magnitude lower than that of quercetin. However, they have remarkable potential due to their multifaceted nature, including the ability to visualize target cells. The most effective theranostic formulation is the combination of the antibiotic (metronidazole) + dye/fluorophore (methylene blue/rhodamine 6G) for visualization of target cells + adjuvant (chalcones or xanthylium derivatives) for antiinflammation effect. This synergistic combination, results in a promising theranostic formulation for treating bacterial infections, with enhanced efficiency, selectivity and minimizing side effects. Full article

Catheter-associated urinary tract infections (CAUTIs) cause serious complications among hospitalized patients due to biofilm-forming microorganisms which make treatment ineffective by forming antibiotic-resistant strains. As most CAUTI-causing bacterial pathogens have already developed multidrug resistance, there is an urgent need for alternative antibacterial agents to prevent biofilms on catheter surfaces. As a trial to find out such a potential agent of natural origin, the bark of Tamarix ericoides Rottl., a little-known plant from the Tamaricaceae family, was examined for its antibacterial and antibiofilm activities against one of the major, virulent, CAUTI-causing bacterial pathogens: Enterococcus faecalis. The methanolic T. ericoides bark extract was analyzed for its antibacterial activity using the well diffusion method and microdilution method. Killing kinetics were calculated using time–kill assay, and the ability of biofilm formation and its eradication upon treatment with the T. ericoides bark extract was studied by crystal violet assay. GC-MS analysis was performed to understand the phytochemical presence in the extract. A in vitro bladder model study was performed using extract-coated catheters against E. faecalis, and the effect was visualized using CLSM. The changes in the cell morphology of the bacterium after treatment with the T. ericoides bark extract were observed using SEM. The biocompatibility of the extract towards L₉₂₉ cells was studied by MTT assay. The anti-E. faecalis activity of the extract-coated catheter tube was quantified by viable cell count method, which exposed 20% of growth after five days of contact with E. faecalis. The anti-adhesive property of the T. ericoides bark extract was studied using CLSM. The extract showed potential antibacterial activity, and the lowest inhibitory concentration needed to inhibit the growth of E. faecalis was found to be 2 mg/mL. The GC-MS analysis of the methanolic fractions of the T. ericoides bark extract revealed the presence of major phytochemicals, such as diethyl phthalate, pentadecanoic acid, methyl 6,11-octadecadienoate, cyclopropaneoctanoic acid, 2-[(2-pentylcyclopropyl) methyl]-, methyl ester, erythro-7,8-bromochlorodisparlure, etc., that could be responsible for the antibacterial activity against E. faecalis. The killing kinetics of the extract against E. faecalis was calculated and the extract showed promising antibiofilm activity on polystyrene surfaces. The T. ericoides bark extract effectively reduced the E. faecalis mature biofilms by 75%, 82%, and 83% after treatment with 1X MIC (2 mg/mL), 2X MIC (4 mg/mL), and 3X MIC (6 mg/mL) concentrations, respectively, which was further confirmed by SEM analysis. The anti-adhesive property of the T. ericoides bark extract studied using CLSM revealed a reduction in the biofilm thickness, and the FDA and PI combination revealed the death of 80% of the cells on the extract-coated catheter tube. In addition, SEM analysis showed extensive damage to the E. faecalis cells after the T. ericoides bark extract treatment, and it was not cytotoxic. Hence, after further studies, T. ericoides bark extract with potential antibacterial, antibiofilm, and anti-adhesive activities can be developed as an alternative agent for treating CAUTIs. Full article

Piezocatalytic materials have attracted widespread attention in the fields of clean energy and water treatment because of their ability to convert mechanical energy directly into chemical energy. In this study, γ-AlON particles synthesised using carbothermal reduction and nitridation (CRN) were used for the first time as a novel piezocatalytic material to degrade dye solutions under ultrasonic vibration. The γ-AlON particles exhibited good performance as a piezocatalytic material for the degradation of organic pollutants. After 120 min under ultrasonic vibration, 40 mg portions of γ-AlON particles in 50 mL dye solutions (10 mg/L) achieved 78.06%, 67.74%, 74.29% and 64.62% decomposition rates for rhodamine B (RhB), methyl orange (MO), methylene blue (MB) and crystal violet (CV) solutions, respectively; the fitted k values were 13.35 × 10⁻³, 10.79 × 10⁻³, 12.09 × 10⁻³ and 8.00 × 10⁻³ min⁻¹, respectively. The piezocatalytic mechanism of γ-AlON particles in the selective degradation of MO was further analysed in free-radical scavenging activity experiments. Hydroxyl radicals (•OH), superoxide radicals (•O₂⁻), holes (h⁺) and electrons (e⁻) were found to be the main active substances in the degradation process. Therefore, γ-AlON particles are an efficient and promising piezocatalytic material for the treatment of dye pollutants. Full article

A plasma bubbling array (PBA) reactor was used to degrade methyl violet (MV) dye, and the effects of input voltage, frequency, and treatment time on MV removal were investigated. Through experimental methods and response surface methodology (RSM), the interactional influences between three parameters were examined. In the actual experiments, when the discharge voltage was set to 4.0 kV and the treatment time was 12 min, the PBA reactor exhibited a high degradation rate (96.15%) and notable energy efficiency (3.16 g/kWh). Under the optimal simulation parameters, the predicted degradation rate of MV is maximized at 98.32%, with only a 2.17% deviation from the actual value. Subsequently, the results of reactive oxygen and nitrogen species (RONS) analysis indicate that superoxide radicals (·O₂⁻) and ozone (O₃) have the greatest impact on MV degradation. The degradation pathway analysis and toxicity evaluation experiments of the solution before and after treatment showed that the toxicity of the solution decreased with the extension of reaction time, and the treated solution may be beneficial to seed germination. Overall, these findings provide valuable insights into the use of plasma technology for the efficient, economical, and sustainable removal of dyes from water. Full article

The aim of the present study was the isolation of high exopolysaccharide (EPS) producers, Lactic Acid Bacteria (LAB) strains, from three types of milk: goat, sheep, and camel milk. Among 112 LAB isolates tested for their ability to produce EPS on MRS-sucrose agar, only 11 strains were able to produce EPS and only three higher producers’ strains were identified by 16S rRNA gene sequencing as two strains of Lactococcus lactis subsp. lactis (SP255, SP257) isolated from camel milk and one strain of Weissella cibaria (SP213) isolated from goat milk. The physicochemical characterization of the purified EPSs revealed a significant sugar yield, with concentrations ranging from 2.17 to 2.77 g/L, while the protein content remained relatively low (0.03 g/L). The UV-visible spectrum showed high Ultra Violet (UV) absorption at 240–280 nm and the Fourier-Transform Infrared (FTIR) spectra showed the presence of a large number of functional groups, including hydroxyl (-OH), carbonyl (-C=O), and methyl groups (-CH3). The EPS solubility indicated their hydrophilic properties and the investigation of interfacial properties indicated that these EPSs could be used as natural emulsifiers and stabilizers in both acidic and neutral emulsions. Moreover, a new type of emulsion system was developed by the utilization of EPSs in the formation of multilayer interfaces in oil-in-water (O/W) emulsions stabilized by sodium caseinate (CAS). Thus, the impact of an EPS addition on the particle size distribution and electrical charge has been studied. At pH 3, the studied EPSs adhered to the surfaces of caseinate-coated droplets and the stability of O/W emulsions was improved by adding certain concentrations of EPSs. The minimum concentration required to stabilize multilayer emulsions for EPSs SP255, EPS SP257, and EPS SP213 was 1.5, 1.5, and 1.7 g/L, respectively. These findings reveal a new EPS with significant potential for industrial use, particularly as an emulsion stabilizer. Full article

Removal of toxic pollutants is of the greatest concerns facing wastewater treatment. In this study, a chemical modification method was used to prepare the maleic anhydride-modified water hyacinth (MA-EC) for the removal of methylene blue (MB) and methyl violet (MV) from water. The maleic anhydride-modified water hyacinth biosorbent was characterized and adsorption experiments were conducted. The prepared MA-EC demonstrated considerable adsorptive efficiency toward MV and MB. It was confirmed that the maximum adsorptive capacities were 1373.58 and 434.70 mg/g for MV and MB, respectively. The adsorptive data were also fitted using Langmuir and Freundlich isotherms, and the results showed that the Langmuir isotherm adsorption model could better describe the adsorptive process. Adsorption–desorption cycling experiments demonstrated that the MA-EC adsorbent had good reusability, with adsorptive capacities of 538.88 mg/g for MV and 215.56 mg/g for MB after four cycles of desorption–adsorption. Full article