Search Results (12)

Tungsten disulfide (WS₂) nanoparticles have emerged in the biomedical field as potential theranostic agents due to their unique properties, including biocompatibility. However, their impact on the immune response remains unexplored. This study aimed to evaluate the effects of inorganic fullerene-like WS₂ (IF-WS₂) nanostructures on human peripheral blood mononuclear cells (PBMCs) in vitro. The study investigated several parameters to evaluate the effects of IF-WS₂ nanoparticles. Cytotoxicity was assessed by measuring cell viability, apoptosis, and necrosis. Internalization of IF-WS₂ by PBMCs was analyzed using morphological and flow cytometric techniques. Proliferation was studied in CellTrace Far Red-prestained total PBMCs stimulated with phytohemagglutinin (PHA) and in isolated T cell cultures stimulated with CD3/CD28-coated beads. Additionally, the production of cytokines and chemokines was measured in culture supernatants of total PBMCs and T cells. IF-WS₂ nanoparticles were non-cytotoxic up to a concentration of 200 µg/mL. Concentrations ≥25 µg/mL inhibited PHA-stimulated PBMC proliferation but did not affect T cell proliferation. Morphological and flow cytometric analysis demonstrated dose- and time-dependent internalization of IF-WS₂ by macrophages. Additionally, IF-WS₂ significantly reduced the production of pro-inflammatory cytokines (IL-1β, TNF-α, IL-8, MCP-1, and GRO-α) in PHA-stimulated PBMCs. Th1, Th17, and Th21 cytokines were downregulated, while Th2, Th9, and T regulatory cytokines were upregulated. In conclusion, this study demonstrated for the first time that pristine IF-WS₂ nanoparticles, at non-cytotoxic concentrations, exhibit notable anti-inflammatory and immunomodulatory properties on activated PBMCs in vitro. Full article

The microstructures and structures of modified Al₂O₃/IF-WS₂ coatings prepared on aluminum substrates are studied. Amorphous Al₂O₃ oxide coatings are obtained on EN AW 5251 aluminum alloy using the electrooxidation process. The quality of the IF-WS₂ nanopowder is of great importance in the process of its introduction into the nanopores of the Al₂O₃ oxide coating. Commercial nanopowder tends to agglomerate, and without appropriate pretreatment, it is difficult to introduce it into the nanopores of the coating. To improve the degree of fragmentation of the IF-WS₂ nanopowder, an experiment was carried out to distribute the nanopowder in the presence of strong ultrasounds, and new conditions for introducing the powder into the nanopores were used. A two-level design of experiment (DOE) was used. The SEM examination made it possible to conclude that Method A contributed to a more even distribution of nanoparticles in the microstructure of Al₂O₃ coatings. GIXD analyses showed the presence of WO₃ derived from the IF-WS₂ modifier next to crystal structures derived from aluminum and WS₂. Modification of coatings using Method A resulted in surfaces with lower contact angles measured with polar liquids and higher surface free energy compared to Method B. Full article

Cationic photo-initiated and polymerized epoxies are characterized by good adhesion, high modulus, zero volatiles, low shrinkage and living polymerization characteristics. Radiation—cured acrylate resins are characterized by rapid initial curing with increased initial strength. The combination of radiation-cured acrylates and epoxies may present advantageous attributes. Thus, the system investigated is a hybrid epoxy/methyl acrylate and three different initiators for cationic polymerization of epoxies, the radical reaction of acrylates and the thermal initiator. When incorporating additives like opaque WS₂ nanoparticles (NPs), absorption of the photo radiation takes place, which may lead to low photo activity. Curing kinetics measurements revealed that the absorbing/masking effect of WS₂ was insignificant, and surprisingly, the level of curing was enhanced when the WS₂ NPs were incorporated. FTIR results demonstrated that covalent bonds were formed between the inorganic fullerenes (IF-WS₂) and the crosslinked matrix. Viscosity measurements showed a surprising reduction of five to ten times in the low-shear viscosity upon NPs incorporation compared to neat resins. It was concluded that the decrease of viscosity by the inorganic NPs, in addition to the enhanced level of conversion, has profound advantages for structural adhesives and 3D printing resins. To the best of our knowledge, this investigation is the first to report on a radiation-induced curing system containing opaque WS₂ NPs that leads to an enhanced degree of curing and reduced shear viscosity. Full article

Exploring the behavior of nanocrystals with varying shapes and sizes under high pressure is crucial to understanding the relationship between the morphology and properties of nanomaterials. In this study, we investigated the compression behaviors of WS₂ nanotubes (NT-WS₂) and fullerene-like nanoparticles (IF-WS₂) by in situ high-pressure X-ray diffraction (XRD) and Raman spectroscopy. It was found that the bulk modulus of NT-WS₂ is 81.7 GPa, which is approximately twice as large as that of IF-WS₂ (46.3 GPa). This might be attributed to the fact that IF-WS₂ with larger d-spacing along the c-axis and higher defect density are more compressible under isotropic pressure than NT-WS₂. Thus, the slender NT-WS₂ possess a more stable crystal structure than the IF-WS₂. Our findings reveal that the effects of morphology and size play crucial roles in determining the high-pressure properties of WS₂ nanoparticles, and provide significant insight into the relationship between structure and properties. Full article

In the current study, inorganic fullerene (IF)-like tungsten disulphide (WS₂) nanoparticles from layered transition metal dichalcogenides (TMDCs) were introduced into a poly(L-lactic acid) (PLLA) polymer matrix to generate novel bionanocomposite materials through an advantageous melt-processing route. The effectiveness of employing IF-WS₂ on the morphology and property enhancement of the resulting hybrid nanocomposites was evaluated. The non-isothermal melt–crystallization and melting measurements revealed that the crystallization and melting temperature as well as the crystallinity of PLLA were controlled by the cooling rate and composition. The crystallization behaviour and kinetics were examined by using the Lui model. Moreover, the nucleating effect of IF-WS₂ was investigated in terms of Gutzow and Dobreva approaches. It was discovered that the incorporation of increasing IF-WS₂ contents led to a progressive acceleration of the crystallization rate of PLLA. The morphology and kinetic data demonstrate the high performance of these novel nanocomposites for industrial applications. Full article

The tribotesting of friction systems requires discussion on proper selection of its conditions and data presentation. System tribology is based, for example, on analysis of the friction contact, the roughness of the cooperating surfaces, and the wear rate of the rubbing elements or coefficient of friction in relation to the sliding distance. Friction pairs, consisting of an aluminum alloy sample with an oxide layer (Al₂O₃) with and without the addition of inorganic fullerenes like tungsten disulphide (IF-WS₂) nanoparticles on its surface cooperating with a counter-sample made of polymer composites prepared on the basis of phenol-formaldehyde resin with different fillers, were tested using a device with a pin-on-plate friction pair system. The results of the experiments showed sufficient durability of the Al₂O₃ and Al₂O₃/IF-WS₂ oxide coatings in combination with the polymer composite. It was found that resin fillers such as cotton fibers, jute fibers, molybdenum disulphide (MoS₂) or graphite (C) influence the friction behavior of the tribological pairs. Although the values of the coefficient of friction obtained in the tests were quite high, their course during the tests ensured stable cooperation of the aluminum coating/polymer composite friction pair on a 15 km distance, under a load of 0.5 MPa. The lowest coefficients of friction were obtained for oxide layers formed on aluminum combined with a polymer composite filled with cotton fibers and graphite. These studies provide information on the tribological properties of commercially available polymer composites cooperating with the produced oxide coatings, supplementing the available literature with the results of research on new, so far unexplored tribological partners. Microscopic investigation of the structure and morphology of the formed surface oxide layers and also microgeometry studies of both the friction elements were used to better understand the obtained research results. Full article

Nanofluids have extensive applications in hydrodynamic journal bearings used in heavy industry machinery. Inorganic fullerene-like tungsten disulfide nanoparticles (IF-WS₂ NPs) are the most common additive for lubrication purpose due to their excellent mechanical characteristics along with their effect on reducing friction and wear. In this work, a computational simulation approach with discrete phase modeling (DPM) of suspended nanoparticles was used to evaluate the application of the IF-WS₂ nanofluid lubricant on load carrying capacity of high-load journal bearings where the normal loads are high, considering the bearing dimensions. For accurate simulation, nanofluid viscosity was calculated considering the aggregation effect of NPs by using scanning electron microscopy (SEM) imaging of the nanofluids. A benchmark study was first performed to assess the model accuracy. Hydrodynamic lubrication was simulated under different nanofluid weigh fractions. The simulated pressure distribution was then employed to determine the load capacity of the bearing. The results show an approximately 20% improvement of load carrying capacity at 5% weight fraction of WS₂-oil nanofluid. Full article

The industrial advancement of high-performance technologies directly depends on the thermo-mechanical properties of materials. Here we give an account of a facile approach for the bulk production of a polyethylene terephthalate (PET)/polypropylene (PP)-based nanocomposite blend with Inorganic Fullerene Tungsten Sulfide (IF-WS₂) nanofiller using a single extruder. Nanofiller IF-WS₂ was produced by the rotary chemical vapor deposition (RCVD) method. Subsequently, IF-WS₂ nanoparticles were dispersed in PET and PP in different loadings to access impact and their dispersion behavior in polymer matrices. As-prepared blend nanocomposites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), dynamic differential scanning (DSC), dynamic mechanical analysis (DMA), and X-ray diffraction (XRD). In this work, the tensile strength of the PP/PET matrix with 1% IF-WS₂ increased by 31.8%, and the thermal stability of the sample PP/PET matrix with 2% increased by 18 °C. There was an extraordinary decrease in weight loss at elevated temperature for the nanocomposites in TGA analysis, which confirms the role of IF-WS₂ on thermal stability versus plain nanocomposites. In addition, this method can also be used for the large-scale production of such materials used in high-temperature environments. Full article

This manuscript summarizes the failure mechanisms found in inorganic fullerene-type tungsten disulfide (IF-WS₂) nanoparticles treated with diverse pressure loading methods. The approaches utilized to induce failure included: the use of an ultrasonic horn, the buildup of high pressures inside a shock tube which created a shock wave that propagated and impinged in the sample, and impact with military rounds. After treatment, samples were characterized using electron microscopy, powder X-ray diffraction, energy dispersive X-ray spectroscopy, and surface area analysis. The microstructural changes observed in the IF-WS₂ particulates as a consequence of the treatments could be categorized in two distinct fracture modes. The most commonly observed was the formation of a crack at the particles surface followed by a phase transformation from the 3D cage-like structures into the 2D layered polymorphs, with subsequent agglomeration of the plate-like sheets to produce larger particle sizes. The secondary mechanism identified was the incipient delamination of IF-WS₂. We encountered evidence that the IF-WS₂ structure collapse initiated in all cases at the edges and vertices of the polyhedral particles, which acted as stress concentrators, independent of the load application mode or its duration. Full article

This manuscript demonstrates the design, modification and initial investigation of a rotary furnace for the manufacturing of inorganic fullerene WS₂ nanoparticles. Different preparation methods starting with various precursors have been investigated, of which the gas-solid reaction starting with WO₃ nanoparticles was the most efficient technique. Furthermore, the influence of temperature, reaction time, and reaction gases etc. on the synthesis of inorganic fullerene WS₂ nanomaterials was investigated, and these parameters were optimised based on combined characterisations using XRD, SEM and TEM. In addition, the furnace was further modified to include a baffled tube, a continuous gas-blow feeding system, and a collection system, in order to improve the batch yield and realise continuous production. This technique has improved the production from less than 1 g/batch in a traditional tube furnace to a few tens of g/batch, and could be easily scaled up to industry level production. Full article

Using inorganic fullerene-like (IF) nanoparticles and inorganic nanotubes (INT) in organic-inorganic hybrid composite, materials provide the potential for improving thermal, mechanical, and tribological properties of conventional composites. The processing of such high-performance hybrid thermoplastic polymer nanocomposites is achieved via melt-blending without the aid of any modifier or compatibilizing agent. The incorporation of small quantities (0.1–4 wt.%) of IF/INTs (tungsten disulfide, IF-WS₂ or molybdenum disulfide, MoS₂) generates notable performance enhancements through reinforcement effects and excellent lubricating ability in comparison with promising carbon nanotubes or other inorganic nanoscale fillers. It was shown that these IF/INT nanocomposites can provide an effective balance between performance, cost effectiveness, and processability, which is of significant importance for extending the practical applications of diverse hierarchical thermoplastic-based composites. Full article

Carbon fiber (CF)-reinforced high-temperature thermoplastics such as poly(phenylene sulphide) (PPS) are widely used in structural composites for aerospace and automotive applications. The porosity of CF-reinforced polymers is a very important topic for practical applications since there is a direct correlation between void content and mechanical properties. In this study, inorganic fullerene-like tungsten disulphide (IF-WS₂) lubricant nanoparticles were used to manufacture PPS/IF-WS₂/CF laminates via melt-blending and hot-press processing, and the effect of IF-WS₂ loading on the quality, thermal and mechanical behaviour of the hybrid composites was investigated. The addition of IF-WS₂ improved fiber impregnation, resulting in lower degree of porosity and increased delamination resistance, compression and flexural properties; their reinforcement effect was greater at temperatures above the glass transition (T_g). IF-WS₂ contents higher than 0.5 wt % increased T_g and the heat deflection temperature while reduced the coefficient of thermal expansion. The multiscale laminates exhibited higher ignition point and notably reduced peak heat release rate compared to PPS/CF. The coexistence of micro- and nano-scale fillers resulted in synergistic effects that enhanced the stiffness, strength, thermal conductivity and flame retardancy of the matrix. The results presented herein demonstrate that the IF-WS₂ are very promising nanofillers to improve the thermomechanical properties of conventional thermoplastic/CF composites. Full article