Search Results (1,225)

Textile production contributes significantly to water pollution, making dye removal crucial for protecting water resources from toxic textile waste. The use of nano-adsorbents for water purification has emerged as a promising approach to removing pollutants from wastewater. Nickel Ferrite (NiFe₂O₄), Iron Oxide (Fe₂O₃), and Nickel Oxide (NiO) nanoparticles (NPs) were prepared via an auto-combustion sol–gel technique using chitosan as a capping and stabilizing agent. The prepared nanomaterials were characterized using various techniques such as XRD, UV-Vis DRS, FT-IR, Raman, EDX, SEM, and TEM to confirm their structure, particle size, morphology, functional groups on the surface, and optical properties. Subsequently, the adsorption of the methylene blue (MB) dye using the prepared nanomaterials was studied. NiFe₂O₄ NPs exhibited the best adsorption behavior compared to the mono-metal oxides. Moreover, all prepared nanomaterials were compatible with the pseudo-second-order model. Further investigations were conducted for NiFe₂O₄ NPs, showing that both the Freundlich and Langmuir isotherm models can explain the adsorption of the MB dye on the surface of NiFe₂O₄ NPs. Factors affecting MB dye adsorption were discussed, such as adsorbent dose, concentration of the MB dye, contact time, pH, and temperature. NiFe₂O₄ NPs exhibited a maximum removal efficiency of the MB dye, reaching 96.8% at pH 8. Different water sources were used to evaluate the ability of NiFe₂O₄ NPs to purify a wide range of water types. Full article

Growing interest in sustainable hydrogen production has brought renewed attention to photoelectrochemical (PEC) water splitting as a promising route for direct solar-to-chemical energy conversion. This study explores how integrating hematite (α-Fe₂O₃) and cupric oxide (CuO) photoelectrodes with a series of nickel-based co-catalysts can improve photoelectrochemical activity. Photoanodic (NiO_x, NiFeO_x, NiWO₄) and photocathodic (Ni, NiCu, NiMo) co-catalysts were synthesized via co-precipitation and mechanochemical methods and characterized through X-ray Diffraction (XRD), X-ray Fluorescence (XRF), Transmission Electron Microscopy–Energy Dispersive X-ray Spectroscopy (TEM-EDX), Scanning Electron Microscopy–Energy Dispersive X-ray Spectroscopy (SEM-EDX), X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) gas-adsorption analyses to clarify their crystallographic, morphological, and compositional properties, as well as their surface chemistry and textural properties (surface area and porosity). Electrochemical tests under 1 SUN illumination showed that NiO_x significantly improves the photocurrent of hematite photoanodes. Among the cathodic co-catalysts, NiMo demonstrated the best performance when combined with CuO photocathodes. For both photoelectrodes, an optimal co-catalyst loading was identified, beyond which performance declined due to potential charge transfer limitations and light attenuation. These findings highlight the critical role of co-catalyst composition and loading in optimizing the efficiency of PEC systems based on earth-abundant materials, offering a pathway toward scalable and cost-effective hydrogen production. Full article

The development of efficient and sustainable advanced oxidation processes (AOPs) for organic pollutant removal is of great significance for water purification. In this study, a CoFeNi-layered double hydroxide (CoFeNi-LDH) catalyst was synthesized and applied for the simultaneous activation of peroxymonosulfate (PMS) and ozone to degrade rhodamine B (RhB) in aqueous solution. The CoFeNi-LDH/PMS/ozone system achieved a remarkable RhB removal efficiency of 95.2 ± 1.2% within 8 min under neutral pH conditions. Systematic parametric studies revealed that synergistic interactions among CoFeNi-LDH, PMS, and ozone contributed to the generation of reactive oxygen species (ROS), primarily sulfate radicals (SO₄^•−) and singlet oxygen (¹O₂), as confirmed by EPR and quenching experiments. Density functional theory (DFT) calculations demonstrated that ozone enhanced PMS adsorption and activation at CoFeNi catalytic sites. The catalyst exhibited robust magnetic recyclability and structural stability after repeated use. This work highlights a synergistic catalytic strategy for PMS/ozone activation, offering an effective and environmentally friendly platform for dye wastewater remediation. Full article

Skarn-type iron ore is economically significant, and numerous skarn ore deposits have been identified in the North China Craton. The newly discovered orbicular diorite in this region is distinguished from other analogous rocks due to the accumulation of large magnetite particles, which may shed new light on the genesis of this ore type. The magnetite in different parts of the orbicular structure exhibits distinct compositional differences. For example, magnetite at the edge has a small particle size (200 μm) and is associated with the minerals plagioclase and hornblende, indicating that it crystallized from normal diorite magma. By contrast, magnetite in the core has a relatively large particle size (>1000 μm), is associated with apatite and actinolite, and contains apatite inclusions as well as numerous pores. The size of magnetite in the mantle falls between that of the edge and the core. The syngenetic minerals of magnetite in the mantle include epidote and plagioclase. The magnetites in the cores of orbicules have a higher content of Ti, Al, Ni, Cr, Sc, Zn, Co, Ga, and Nb than those in the rim. The δ⁵⁶Fe value of the core magnetite (0.46‰–0.78‰) is much higher than that of the mantle and rim magnetite in orbicules. Moreover, the δ⁵⁶Fe value of magnetite increases as the V content of magnetite gradually decreases. This large iron isotope fractionation is likely driven by liquid immiscibility that forms iron-rich melts under high oxygen fugacity. The reaction between magma and carbonate xenoliths (Ca, Mg)CO₃ during magma migration generates abundant CO₂, which significantly increases the oxygen fugacity of the magmatic system. Under the action of CO₂ and other volatile components, liquid immiscibility occurs in the magma chamber, and Fe-rich oxide melts are formed by the melting of carbonate xenoliths. Iron oxides (Fe₃O₄/Fe₂O₃₎ will crystallize close to the liquidus due to high oxygen fugacity. These characteristics of magnetite in the Tanling orbicular diorite (Wuan, China) indicate that diorite magma reacts with carbonate xenoliths to form “Fe-rich melts”, and skarn iron deposits are probably formed by the reaction of intermediate-basic magma with carbonate rocks that generate such “Fe-rich melts”. A possible reaction is as follows: diorite magma + carbonate → (magnetite-actinolite-apatite) + garnet + epidote + feldspar + hornblende + CO₂↑. Full article

Citrus creasing is a physiological rind disorder. Satsuma mandarin (Citrus unshiu Marc.) is the most widely cultivated mandarin variety worldwide and exhibits a high susceptibility to creasing. To investigate the physiological mechanisms underlying creasing, satsuma mandarin trees were treated with different drought stress during fruit expansion, then the relationship between the soil water content and creasing incidence was analyzed, while also examining the rind morphology, oil gland distribution in the flavedo, antioxidant enzyme activities, hormone concentrations, cell wall components, mineral content of creasing fruit, and the impact of creasing on fruit quality. Results showed that severe water stress (35% SRWC) increased the creasing incidence rate by 28% compared to well-irrigated treatments (80% SRWC). The creasing fruit oil gland diameter reduced by 35.7% and the density increased by 149.7% compared to healthy fruits. Simultaneously, the content of H₂O₂ and proline elevated by 47.1% and 8.3% respectively, and the activities of SOD, POD, and CAT of the creasing rind were enhanced significantly. Additionally, the content of IAA, ZR, and MeJA decreased by 17.2%, 7.8%, and 50.2%, respectively. Cell wall components such as cellulose, hemicellulose, and protopectin content reduced by 44.6%, 31.7%, and 33.1%, while soluble pectin increased by 36.3%. Significant alterations were observed in several minerals (Al, Fe, Na, Ni, V, Ga, Zn, Ba, Sn, Hg, Sc, Y, and La). However, fruit quality remained unaffected by creasing. These results demonstrate that drought is a key factor inducing creasing. Increased oil gland density, the degradation of cell wall components, elevated oxidative stress, reductions in phytohormones, and altered mineral element content work together to contribute to rind cells’ structural instability and lead to creasing in the satsuma mandarin. Full article

The chemical looping steam reforming of methane (CLSR) employing Fe-containing oxygen carriers can produce syngas and hydrogen simultaneously. However, Fe-based oxygen carriers exhibit low CH₄ activation ability and cyclic stability. In this work, oxygen carriers with fixed Fe content and different Fe/Ni ratios were synthesized by the sol–gel method to investigate the effects of Ni-Fe-Al interactions on CLSR performance. Ni-Fe-Al interactions promote the growth of the spinel structure and regulate both the catalytic sites and the available lattice oxygen, resulting in the CH₄ conversion and CO selectivity being maintained at 96–98% and above 98% for the most promising oxygen carrier, with an Fe₂O₃ content of 20 wt% and Fe/Ni molar ratio of 10. The surface, phase, and particle size were kept the same over 90 cycles, leading to high stability. During the CLSR cycles, conversion from Fe³⁺ to Fe²⁺/Fe⁰ occurs, along with transformation between Ni²⁺ in NiAl₂O₄ and Ni⁰. Overall, the results demonstrate the feasibility of using spinel containing earth-abundant elements in CLSR and the importance of cooperation between oxygen release and CH₄ activation. Full article

With their considerable capacity and structurally favorable characteristics, layered transition metal oxides have become strong contenders for cathode use in sodium-ion batteries (SIBs). Nevertheless, their practical deployment is challenged by pronounced capacity loss, predominantly induced by unstable cathode–electrolyte interphase (CEI) at elevated voltages. In this study, difluoroethylene carbonate (DFEC) is introduced as a functional electrolyte additive to engineer a robust and uniform CEI. The fluorine-enriched CEI effectively suppresses parasitic reactions, mitigates continuous electrolyte decomposition, and facilitates stable Na⁺ transport. Consequently, Na/NaNi_1/3Fe_1/3Mn_1/3O₂ (Na/NFM) cells with 2 wt.% DFEC retain 78.36% of their initial capacity after 200 cycles at 1 C and 4.2 V, demonstrating excellent long-term stability. Density functional theory (DFT) calculations confirm the higher oxidative stability of DFEC compared to conventional solvents, further supporting its interfacial protection role. This work offers valuable insights into electrolyte additive design for high-voltage SIBs and provides a practical route to significantly improve long-term electrochemical performance. Full article

The 316L stainless steel, uncoated and coated with two types of EB-PVD thin-film deposits, was tested in liquid lead both under oxygen-saturated conditions (~10⁻³ wt.%) for exposure times of 1000 and 2000 h and under low-oxygen conditions (~10⁸ wt.%) for 1000 h. The first coating consisted of a ~1 µm NiCrAlY thin film. At the same time, the second was a NiCrAlY/Al₂O₃ multilayer with a total thickness of ~3 µm, on top of which an additional 100–200 nm metallic Cr layer was deposited. Uncoated specimens tested under oxygen-saturated conditions developed a duplex oxide layer on their surface. SEM-EDS analyses revealed that the inner layer was denser and contained Fe, Cr, and O, whereas the outer layer was more porous and composed mainly of Fe and O. Microscopic examinations indicated that the multilayer-coated specimens exposed to low-oxygen conditions exhibited no signs of material degradation. In contrast, both the uncoated samples and those coated only with a single NiCrAlY layer showed generalised corrosion over the entire surface after exposure to liquid lead at low oxygen concentrations. The austenitic microstructure was degraded to a depth of 100–200 µm. Vickers microhardness indentations performed on the structurally altered regions revealed two distinct corrosion zones with markedly different hardness values. Full article

This study aims to determine the optimal Mo content for corrosion resistance in two alloys, FeCoCrNiMo_x and Fe_0.5CoCrNiMo_x. The alloys were fabricated using laser powder bed fusion (LPBF) technology with varying Mo contents (x = 0, 0.05, 0.1, 0.15). The corrosion behavior of these alloys was investigated in 3.5 wt.% NaCl solution at room temperature and 60 °C using electrochemical testing and X-ray photoelectron spectroscopy (XPS). The results show that all alloys exhibit good corrosion resistance at room temperature. However, at 60 °C, both alloys without Mo addition exhibit severe corrosion, while the Fe_0.5CoCrNiMo_0.1 alloy demonstrates the best corrosion resistance while maintaining the highest strength. The enhanced corrosion resistance is attributed to the optimal molybdenum addition, which refines the passive film structure and promotes the formation of Cr₂O₃. Furthermore, molybdenum oxide exists as MoO₄²⁻ ions on the surface of the passive film, significantly improving the alloy’s corrosion resistance in chloride-containing environments. Full article

The high material cost has restricted the development of concentrated solar power (CSP) systems. In this study, a low-cost alternative material was developed by adding aluminum to 304 stainless steel to form a protective oxide film, thereby enhancing its corrosion resistance to molten salt. Three material variants were tested: untreated hot-rolled plates after solution treatment and cold-rolled high-aluminum 304 stainless steel (High-Al304SS) after solution treatment and annealing treatment. After all samples were immersed in a NaNO₃-KNO₃ mixed salt at 600 °C for 480 h, corrosion products including NaFeO₂, CrO₂, Mn₂O₄, and NiCr₂O₄ were formed. The phase composition was determined by XRD, and the surface and cross-section of the corrosion layer were analyzed by SEM and EDS surface and point analysis. The corrosion rate of the samples was calculated by the weight loss method. Notably, an Al₂O₃-Cr₂O₃ composite oxide film was formed on the sample surface, effectively inhibiting corrosion. The high defect density and grain boundary energy introduced by the cold-rolling process, as well as the precipitation of the second phase during annealing, accelerated the corrosion process of the samples. However, the hot-rolled samples after solution treatment exhibited excellent corrosion resistance (64.43 μm/year) and, through further process optimization, are expected to become an ideal low-cost alternative material for 347H stainless steel (23 μm/year) in CSP systems. Full article

This paper studies the formation process of a composite material based on an organic substance, biochar from sunflower husks, and an inorganic substance, nickel (II)-copper (II) ferrites of the composition Cu_xNi_1−xFe₂O₄ (x = 0.0; 0.5; 1.0). The obtained materials were characterized by X-ray phase analysis, scanning electron microscopy, and FTIR spectroscopy. It is shown that when replacing copper (II) cations with nickel (II) cations, the average parameters and volume of the unit cell gradually decrease, and the cation–anion distances in both the tetrahedral and octahedral spinel grids also decrease with regularity. The oxide materials were found to form a film on the surface of biochar, repeating its porous structure. The obtained materials exhibit high catalytic activity in the methyl orange decomposition reaction under the action of hydrogen peroxide in an acidic medium; the degradation of methyl orange in an aqueous solution occurs 30 min after the start of the reaction. This result may be associated with the formation of the Fenton system during the oxidation–reduction process. A significant increase in the reaction rate in the system containing mixed nickel–copper ferrite as a catalyst may be associated with the formation of a more defective structure due to the Jahn–Teller effect manifestation, which creates additional active centers on the catalyst surface. Full article

The alarming rise in foodborne illnesses, particularly those associated with microbial contamination in meat products, presents a serious challenge to global food safety. Among these microbial threats, Pseudomonas aeruginosa (P. aeruginosa) poses a critical threat due to its biofilm-forming capability and prevalence in contaminated beef, highlighting its effective real-time detection. Herein, we report the fabrication of a novel electrochemical aptasensor based on multimetal perovskite (FeCoCuNiO) doped with urea-derived graphitic carbon nitride (g-C₃N₄), synthesized via a sol–gel combustion method. The FeCoCuNiO-g-C₃N₄ nanocomposite was then coated onto a graphitic pencil electrode and functionalized with a DNA-based aptamer specific towards P. aeruginosa. The resulting aptasensor exhibited a low detection limit of 3.03 CFU mL⁻¹ with high selectivity and sensitivity, and was successfully applied to real-time detection of P. aeruginosa in food samples. To the best of our knowledge, this work presents the first FeCoCuNiO-g-C₃N₄-based aptasensor for bacterial detection, offering a promising platform for food safety assurance and public health protection. Full article

This study was conducted to evaluate the high-temperature protection performance of new hard coating systems. Woka 7202 (Cr₃C₂-NiCr) and Diamalloy 2002 (WC-NiCrFeBSiC) powders were coated onto 316L stainless steel substrates using the atmospheric plasma spraying (APS) method and subjected to isothermal oxidation (5–100 h) and hot corrosion (55% V₂O₅ + 45% Na₂SO₄, 1–5 h) tests. Although the coatings exhibited a laminar microstructure and some pores, cracks, and oxide-containing regions, they did not show any flaking or structural integrity deformations during the tests. Microstructural changes, oxide layer morphology, and the phases formed were examined in detail. The findings demonstrate that these coating systems not only provide chemical and structural stability against existing high-temperature environments, but also meet the requirements of next-generation thermal protection needs. In this regard, the study provides directly applicable information for the coating design and performance optimization for turbine blades, energy production equipment, and similar industrial components exposed to high-temperature oxidation and hot corrosion. Full article

The monitoring of partial discharge activity is part of very basic methods used to determine the status of insulation systems in high-voltage electric power devices. These methods use direct galvanic coupled measurement, measurement by inductive offline methods, or other non-electric methods. The inductive method requires sensitive inductive sensors, which detect the partial discharge pulses occurring in high-voltage circuits. The sensitivity of such sensors strongly depends on the design, construction, and materials of the sensor core. Therefore, knowledge of the magnetic material parameters of a sensor is crucial for obtaining optimal values in terms of the sensor’s final sensitivity. In this experiment, experimental sensor cores were constructed using different magnetic materials and different sensor construction processes. For the laboratory experiments, two types of magnetic material were selected: a magnetic material based on Fe-Ni (Permalloy) and a magnetic material based on MO.Fe₂O₃. As a reference level for sensitivity, the minimum acceptable sensitivity was defined as the equivalent measuring sensitivity obtained using the direct galvanic measurement method. The optimal construction type and magnetic material for the sensor core of inductive sensors were determined. Full article

The growing accumulation of waste lubricating oil presents serious environmental issues, calling for sustainable management solutions. This research discusses the creation of FeNi/TiO₂ nanocatalysts that were synthesized through an eco-friendly method utilizing grape seed extract (GSE) as a natural reducing agent for the catalytic pyrolysis of waste lubricating oil. The nanocatalyst was produced using the microemulsion technique and refined via Response Surface Methodology (RSM) to optimize its catalytic performance. Pyrolysis was carried out at 400 °C, leading to a significant conversion of waste oil into valuable fuel. The FeNi/TiO₂ nanocatalyst exhibited exceptional capabilities in facilitating the breakdown of heavy hydrocarbons into lighter fuel fractions while reducing unwanted byproducts. GC-MS analysis demonstrated the prevalence of C6–C20 hydrocarbons in the pyrolysis oil, underscoring its potential as a high-quality alternative fuel similar to traditional diesel. This study aids in the progress of environmentally sustainable waste-to-energy technologies, offering a promising pathway for effective fuel production and hazardous waste management. Full article