Search Results (40)

Efficient lubrication lowers friction, wear, and energy losses in automotive drivetrain components. Advanced lubricants are key to sustainable transportation performance, durability, and efficiency. This study analyzes the tribological performance of Group III base oil with CuO and ZnO nanoadditive mixtures. These additives enhance the performance of Group III base oils, making them highly relevant for automotive lubricant applications. An Optimol SRV5 tribometer performed ball-on-disk sliding contact tests with 100Cr6 steel specimens subjected to a 50 N force and a temperature of 100 °C. The test settings are designed to mimic the boundary and mixed lubrication regimes commonly seen in the automobile industry. During the tests, the effect of nanoparticles on friction was measured. Microscopic wear analysis was performed on the worn specimens. The results demonstrate that adding 0.3 wt% CuO nanoparticles to Group III base oil achieves a 19% reduction in dynamic friction and a 47% decrease in disk wear volume compared to additive-free oil. Notably, a 2:1 CuO-to-ZnO mixture produced synergy, delivering up to a 27% friction reduction and a 54% decrease in disk wear. The results show the synergistic effect of CuO and ZnO in reducing friction and wear on specimens. This study highlights the potential of nanoparticles for lubricant development and automotive applications. Full article

This study systematically investigates the impact of Cu²⁺ doping on the structural, magnetic, and magnetocaloric properties of Cu_xCo_1−xCr₂O₄ nanoparticles synthesized via a solution combustion method. Cu incorporation up to x = 20% induces a progressive structural transformation from a cubic spinel to a trigonal corundum phase, as confirmed by X-ray diffraction and Raman spectroscopy. The doping process also leads to increased particle size, improved crystallinity, and reduced agglomeration. Magnetic measurements reveal a transition from hard to soft ferrimagnetic behavior with increasing Cu content, accompanied by a notable rise in the Curie temperature from 97.7 K (x = 0) to 140.2 K (x = 20%). The magnetocaloric effect (MCE) is significantly enhanced at higher doping levels, with the 20% Cu-doped sample exhibiting a maximum magnetic entropy change (−ΔS_M) of 2.015 J/kg-K and a relative cooling power (RCP) of 58.87 J/kg under a 60 kOe field. Arrott plot analysis confirms that the magnetic phase transitions remain second-order in nature across all compositions. These results demonstrate that Cu doping is an effective strategy for tuning the magnetostructural response of CoCr₂O₄ nanoparticles, making them promising candidates for low-temperature magnetic refrigeration applications. Full article

Copper oxide nanoparticles (CuO-NPs) induce neurological diseases, including neurobehavioral defects and neurodegenerative diseases. Direct evidence indicates that CuO-NPs induce inflammation in the central nervous system and cause severe neurotoxicity. However, the mechanism of CuO-NP-induced damage to the nervous system has rarely been studied, and the toxicity of different CuO-NP particle sizes and their copper ion (Cu²⁺) precipitation in microglia (BV2 cells) is worth exploring. Therefore, this study investigated CuO-NPs with different particle sizes (small particle size: S-CuO-NPs; large particle size: L-CuO-NPs), Cu²⁺ with equal molar mass (replaced by CuCl₂ [Equ group]), and Cu²⁺ precipitated in a cell culture solution with CuO-NPs (replaced by CuCl₂ [Pre group]), and examined the mechanism of action of each on BV2 microglia after co-culture for 12 h and 24 h. The activity of BV2 cells decreased, the morphology was damaged, and the apoptosis rate increased in all the exposed groups. Toxicity increased time- and dose-dependently, and was highest in the Equ group, followed by the S-CuO-NPs, L-CuO-NPs, and Pre groups, respectively. Subsequently, we investigated the mechanism of S-CuO-NP-induced cell injury, and revealed that S-CuO-NPs induced oxidative stress and inflammatory response and increased the membrane permeability of BV2 cells. Moreover, S-CuO-NPs reduced the ratio of p-CSF-1R/CSF-1R, p-PLCγ2/PLCγ2, p-extracellular signal-regulated kinase (ERK)/ERK, p-Nrf2/Nrf2, and Bcl-2/Bax protein expression in microglia, and elevated cleaved caspase-3 expression. The CSF-1R/PLCγ2/ERK/Nrf2 apoptotic pathway was activated. The downregulation of CX3CR1, CSF-1R, brain-derived neurotrophic factor (BDNF), and IGF-1 protein expression indicates impairment of the repair and protection functions of microglia in the nervous system. In summary, our results reveal that CuO-NPs promote an increase in inflammatory molecules in BV2 microglia through oxidative stress, activate the CSF-1R/PLCγ2/ERK/Nrf2 pathway, cause apoptosis, and ultimately result in neurofunctional damage to microglia. Full article

Tattoo inks contain varying amounts of metal nanoparticles (NPs) < 100 nm that, due to their unique physicochemical properties, may have specific biological uptake and cause skin or systemic toxicities. The toxic effects of certified reference standards of metal NPs and samples of commercially available tattoo inks were investigated using an in vitro system and a novel human ex vivo model. In vitro toxicity was evaluated using vitality assays on human skin cells (HaCaT cell line, primary fibroblasts, and keratinocytes). No toxicity was observed for Al₂O₃, Cr₂O₃, Fe₂O₃, and TiO₂ NPs, whereas CuO NPs showed dose-dependent toxicity on HaCaT and primary fibroblasts. Fibroblasts and keratinocytes were also sensitive to high concentrations of ZnO NPs. Reference standards and ink samples were then injected ex vivo into human skin explants using tattoo needles. Histological analysis showed pigment distribution deep in the dermis and close to dermal vessels, suggesting possible systemic diffusion. The presence of an inflammatory infiltrate was also observed. Immunohistochemical analysis showed increased apoptosis and expression of the inflammatory cytokine interleukin-8 in explants specifically tattooed with the reference standard or red ink. Taken together, the results suggest that the tattooing technique leads to exposure to toxic metal NPs and skin damage. Full article

The influence of as-cast grain size on recrystallization and the related mechanical properties of Al–Zn–Mg–Cu-based alloys was investigated. Grain sizes ranging from 163 to 26 μm were achieved by adding Ti, Cr and Mn, and ZnO nano-particles, which acted as heterogeneous nucleation sites. A decrease in the as-cast grain size led to a corresponding reduction in the recrystallized grain size from 54 to 13 μm. Notably, as-cast grain sizes below 100 μm provided additional nucleation sites at grain boundaries, allowing for a reasonable prediction of recrystallized grain size. Finer grains also contributed to enhanced mechanical properties, with yield strength increasing as recrystallized grain size decreased without significant loss of elongation. Additional strengthening was observed due to η-precipitates at grain boundaries, further improving the properties of fine-grained sheets. Full article

CuM and AgM (M = Cr, Fe) catalysts were synthesized, characterized, and evaluated in methane reforming with CO₂ with and without pretreatment under a H₂ atmosphere. Their textural and structural characteristics were evaluated using various physicochemical methods, including XRD, B.E.T., SEM-EDS, XPS, and H₂-TPR. It was shown that the nature of the species has a significant effect on these structural, textural, and reactivity properties. AgCr catalysts, presenting several oxidation states (Ag⁰, Ag⁺¹, Cr³⁺, and Cr⁶⁺ in Ag, AgCrO₂, and AgCr₂O₄), showed the most interesting catalytic performance in their composition. The intermediate Cr₂O₃ phase, formed during the catalytic reaction, played an important role as a catalytic precursor in the in situ production of highly dispersed nanoparticles, being less prone to coke formation in spite of the severe reaction conditions. In contrast, the AgFe catalyst showed low activity and a low selectivity for DRM in the explored temperature range, due to a significant contribution of the reverse water–gas shift reaction, which accounted for the low H₂/CO ratios. Full article

The ceramic tile industry, with significant energy and material demands in its manufacturing processes, has employed technological innovations in energy efficiency, advanced equipment and tile thickness reduction to address these challenges. This study aimed to assess the impact of Ag₂O, CuFe₂O₄, Fe₃O₄, and SiO₂ nanoparticles (0%, 1%, and 5% by weight) on the mechanical strength, water absorption, and apparent thermal conductivity of ceramic tiles, as well as their capacity to reduce energy and raw material consumption. This reduction translates into a decrease in environmental impacts, which have been evaluated through life cycle assessment (LCA) methodology applied to the manufacturing processes. Nanoparticles (Ag₂O, CuFe₂O₄, Fe₃O₄, and SiO₂) were initially screened on TF clay (0%, 1%, 5% w/w), and the most effective were applied to CR1 and CR2 clays (0%, 1%, 5% w/w). Findings indicated a 32% increase in temperature gradient and a 16% improvement in flexural strength with the addition of Fe₃O₄ nanoparticle at 1% (w/w) in TF clay. Furthermore, there was a potential 48% reduction in energy consumption, and up to 16% decrease in tile weight or thickness without affecting the flexural strength property of the test tiles. LCA results demonstrated that the addition of Fe₃O₄ nanoparticle has potential reductions of up to 20% in environmental impacts. This study suggests that nanoparticle addition offers a viable alternative for reducing energy and material consumption in the ceramic tile industry. Future research should focus on assessing the economic impact of transitioning to a sustainable business model in the ceramic tile industry with nanoparticles addition. Full article

Superparamagnetic magnetic nanoparticles (MNPs, Fe₃O₄) were first synthesized based on a chemical co–precipitation method, and the core–shell magnetic silica nanoparticles (MSNPs, Fe₃O₄@SiO₂) were obtained via hydrolysis and the condensation of tetraethyl orthosilicate onto Fe₃O₄ seed using a sol–gel process. Following that, MSNPs were immobilized using a three–step grafting strategy, where 8-hloroacetyl–aminoquinoline (CAAQ) was employed as a metal ion affinity ligand for trapping specific heavy metal ions, and a macromolecular polymer (polyethylenimine (PEI)) was selected as a bridge between the surface hydroxyl group and CAAQ to fabricate a network of organic networks onto the MSNPs’ surface. The as–synthesized MSNPs–CAAQ nanocomposites possessed abundant active functional groups and thus contained excellent removal features for heavy metal ions. Specifically, the maximum adsorption capacities at room temperature and without adjusting pH were 324.7, 306.8, and 293.3 mg/g for Fe³⁺, Cu²⁺, and Cr³⁺ ions, respectively, according to Langmuir linear fitting. The adsorption–desorption experiment results indicated that Na₂EDTA proved to be more suitable as a desorbing agent for Cr³⁺ desorption on the MSNPs–CAAQ surface than HCl and HNO₃. MSNPs–CAAQ exhibited a satisfactory adsorption capacity toward Cr³⁺ ions even after six consecutive adsorption–desorption cycles; the adsorption efficiency for Cr³⁺ ions was still 88.8% with 0.1 mol/L Na₂EDTA as the desorbing agent. Furthermore, the MSNPs–CAAQ nanosorbent displayed a strong magnetic response with a saturated magnetization of 24.0 emu/g, and they could be easily separated from the aqueous medium under the attraction of a magnet, which could facilitate the sustainable removal of Cr³⁺ ions in practical applications. Full article

The biogenic synthesis of copper oxide nanoparticles was explored using the Myriophyllum spicatum plant through a process involving co-precipitation and was utilized as an effective photocatalyst for the reduction of Cr(VI) and Pb(II) ions in an aqueous solution. The plant-mediated CuO nanoparticles were characterized using microscopic techniques (TEM and SEM), FT-IR, and XRD analyses. The amount of the reduced metal ions was determined by UV–visible and Atomic Absorption (AA) spectrophotometers. The analyses of the functional group present in the leaf extract revealed the type of bioactive molecules that were involved in the formation of copper oxide nanoparticles. The nanoparticles were used in the photo-enhanced reduction of hexavalent Cr and divalent Pb ions, and the impact of solution pH, initial metal concentrations, and photocatalyst dosage was investigated to establish the optimal performance of the CuO nanoparticles. Results revealed a direct association between the reduction of metal ions and catalyst dosage in both cases. A maximum percentage reduction of 89.2% and 79.1% was achieved for Cr(VI) and Pb(II), respectively, using 3 g of the CuO nanoparticles. This confirms that the CuO nanoparticles exhibited higher efficiency for Cr(VI) reduction as compared to Pb(II) reduction and indicates that CuO nanoparticles are a promising photocatalyst that is capable of reducing these metal ions into less toxic products. Full article

Metal nanoparticle fabrication through plant-based green methods is considered the gold standard among the various synthesis techniques owing to its simplicity, eco-friendliness, ease of use, and the huge diversity of plant species. Copper nanoparticles (CuONPs) have proven their potential in the fields of medicine, agriculture, pharmaceutics, and catalysis, and are being synthesized using various physicochemical and biological methods. Here, the authors have reported on the first-ever use of Albizia saman leaf extract for the development of CuONPs. Phytochemical analysis of the methanolic extracts of the plant exhibited the presence of phenols (32.31%), tannins (12.27%), and flavonoids (16.72%). The phytonutrients existing in leaf extract successfully reduced the copper salt in the CuONPs. A detailed investigation of the synthesized CuONPs was performed using advanced instruments. The UV-Vis spectra exhibited an absorbance peak at 290 nm, while the X-ray diffraction pattern (XRD) revealed that the average crystallite size was about 29.86 nm. Dynamic light scattering (DLS) revealed that the average hydrodynamic size of the CuONPs was 72.3 nm in diameter, while its zeta potential was −0.49, with a negative polarity. Fourier transform infrared spectroscopy showed the major bands in the region of 400 to 1000 cm⁻¹, suggesting the formation of CuONPs, while the band in the region of 1100 to 2600 cm⁻¹ shows the association of plant molecules with the phytonanofabricated CuO particles. Transmission and scanning electron microscopy showed the spherical shape of the CuONPs, whose size was about 20–50 nm. The phytonanofabricated CuO exhibited antibacterial activity by forming a zone of inhibition (ZOI) against Escherichia coli, Staphylococcus aureus, and Candida albicans. The removal efficiency of the CuONPs was 33.33% for Congo Red dye. The removal efficiency of the phytonanofabricated CuO for CR dye was reduced to 16% after the 4th cycle. Full article

The cooling paths and kinetics in the system Cu-Fe-O are investigated by the empirical micro- and nanoscale analysis of slags from the flash furnace smelter at Olympic Dam, South Australia. We aim to constrain the exsolution mechanism of delafossite (Cu¹⁺Fe³⁺O₂) from a spinel solid solution (magnetite, Fe₃O₄) and understand why cuprospinel (CuFe₂O₄) is never observed, even though, as a species isostructural with magnetite, it might be expected to form. Flash furnace slags produced in the direct-to-blister copper smelter at Olympic Dam contain four Cu-bearing phases: Cu-bearing magnetite, delafossite, metallic copper, and cuprite. Delafossite coexists with magnetite as rims and lamellar exsolutions, as well as bladed aggregates, associated with cuprite within Si-rich glass. The empirical compositions of magnetite and rim delafossite are (Fe²⁺_6.89Cu²⁺_0.86Co_0.13Mg_0.15Si_0.02)_8.05 (Fe³⁺_15.52Al_0.41Ti_0.01Cr_0.01)_15.95O₃₂, and (Cu¹⁺_0.993Co_0.002Mg_0.002)_0.997(Fe³⁺_0.957Al_0.027Ti_0.005Si_0.004)_0.993O₂, respectively. The measured Cu content of magnetite represents a combination of a solid solution (~6 mol.% cuprospinel endmember) and exsolved delafossite lamellae. Atomic-resolution high-angle annular dark field scanning transmission electron microscope (HAADF STEM) imaging shows epitaxial relationships between delafossite lamellae and host magnetite. Defects promoting the formation of copper nanoparticles towards the lamellae margins suggest rapid kinetics. Dynamic crystallization under locally induced stress in a supercooled system (glass) is recognized from misorientation lamellae in delafossite formed outside magnetite grains. The observations are concordant with crystallization during the cooling of molten slag from 1300 °C to <1080 °C. Melt separation through an immiscibility gap below the solvus in the system Cu-Fe-O is invoked to form the two distinct delafossite associations: (i) melt-1 from which magnetite + delafossite form; and (ii) melt-2 from which delafossite + cuprite form. Such a path also corroborates the published data explaining the lack of cuprospinel as a discrete phase in the slag. Delafossite rims form on magnetite at a peritectic temperature of ~1150 °C via a reaction between the magnetite and copper incorporated in the oxide/Si-rich melt. The confirmation of such a reaction is supported by the observed misfit orientation (~10°) between the rim delafossite and magnetite. HAADF STEM imaging represents a hitherto underutilized tool for understanding pyrometallurgical processes, and offers a direct visualization of phase relationships at the smallest scale that can complement both experimental approaches and theoretical studies based on thermodynamic modelling. Full article

Globally, efforts are being made to upgrade and improvise the current wastewater treatment technologies. Industrial wastewater is being generated exponentially, owing to the expansion in chemical industries and civilizations necessitating remediation to prevent further environmental damage and lower associated human risks. In this work, iron oxide nanoparticles (IONPs) have been developed and employed as an efficient nanocatalyst for heavy metal adsorption via the chemical route. The shape, absorbance optical, crystal phase, and magnetization of as-prepared magnetic nanostructures were characterized using XRD (X-ray diffraction), UV-Vis (ultraviolet-visible), HRTEM (High-resolution transmission electron microscopy), FTIR (Fourier transfer infrared spectroscopy), and VSM. Further, the adsorption ability of iron oxide to remove the bulk metallic elements considering cadmium (Cd), lead (Pb), zinc (Zn), chromium (Cr), copper (Cu), and nickel (Ni), present in industrial effluents, were studied. The Maghemite Fe₂O₃ crystal phase having an R-3c group is observed in the XRD results. An identical shape of spherical nanostructures is determined using TEM including ≈21 nm for pure Fe₂O₃. A removal % was studied by using ICP-OES, and showed a Cr (61.2%), Cd (98%), Cu (66%), Ni (64%), Zn (97%), and Pb (98%) removal ability. The application of such monitored nanomaterials to effluent cleaning and sewage discharge emitted via labs and petrochemical industries could be expanded. Full article

Herein, the aqueous extract of Portulaca oleracea has been used as a safe, cheap, eco-friendly, and applicable scale-up method to bio-fabricate copper oxide nanoparticles (CuO-NPs). The character of CuO-NPs were determined using UV-vis spectroscopy, Fourier transform infrared (FT-IR), X-ray diffraction (XRD), Transmission electron microscopy (TEM), Energy dispersive X-ray(EDX), Dynamic light scattering (DLS), and zeta potential. Spherical and crystalline CuO-NPs with a size range of 5–30 nm at a maximum surface plasmon resonance of 275 nm were successfully fabricated. The main components of the green-synthesized particles were Cu and O with weight percentages of 49.92 and 28.45%, respectively. A Zeta-potential value of −24.6 mV was recorded for CuO-NPs, indicating their high stability. The plant-based CuO-NPs showed promising antimicrobial and catalytic activity in a dose-dependent manner. Results showed that the synthesized CuO-NPs had the efficacy to inhibit the growth of pathogens Staphylococcus aureus, Bacillus subtilis, Escherichia coli, Pseudomonas aeruginosa, and Candida albicans with low MIC values in the ranges of 6.25–25 µg/mL. The highest decolorization percentages of tanning wastewater were attained under sunlight irradiation conditions at a concentration of 2.0 mg/mL after 200 min with percentages of 88.6 ± 1.5% compared to those which were recorded under dark conditions (70.3 ± 1.2%). The physicochemical parameters of tanning wastewater including total suspended solids (TSS), total dissolved solids (TDS), chemical oxygen demand (COD), biological oxygen demand (BOD), and conductivity under optimum conditions were significantly decreased with percentages of 95.2, 86.7, 91.4, 87.2, and 97.2%, respectively. Interestingly, the heavy metals including cobalt (Co), lead (Pb), nickel (Ni), cadmium (Cd), and chromium (Cr (VI)) decreased with percentages of 73.2, 80.8, 72.4, 64.4, and 91.4%, respectively, after treatment of tanning wastewater with CuO-NPs under optimum conditions. Overall, the plant-synthesized CuO-NPs that have antimicrobial and catalytic activities are considered a promising nano-catalyst and environmentally beneficial to wastewater treatment. Full article

An environmentally safe, efficient, and economical microwave-assisted technique was selected for the production of silver nanoparticles (AgNPs). To prepare uniformly disseminated AgNPs, xanthan gum (XG) was utilized as both a reducing and capping agent. UV–Vis spectroscopy was used to characterize the formed XG-AgNPs, with the absorption band regulated at 414 nm under optimized parameters. Atomic force microscopy was used to reveal the size and shape of XG-AgNPs. The interactions between the XG capping agent and AgNPs observed using Fourier transform infrared spectroscopy. The XG-AgNPs were placed in between glassy carbon electrode and Nafion^® surfaces and then deployed as sensors for voltammetric evaluation of mercury ions (Hg²⁺) using square-wave voltammetry as an analytical mode. Required Nafion^® quantities, electrode behavior, electrolyte characteristics, pH, initial potentials, accumulation potentials, and accumulation durations were all comprehensively investigated. In addition, an electrochemical mechanism for the oxidation of Hg²⁺ was postulated. With an exceptional limit of detection of 0.18 ppb and an R² value of 0.981, the sensors’ measured linear response range was 0.0007–0.002 µM Hg²⁺. Hg²⁺ evaluations were ultimately unaffected by the presence of many coexisting metal ions (Cd²⁺, Pb²⁺, Cr₂O₄, Co²⁺,Cu²⁺, CuSO₄). Spiked water samples were tested using the described approach, with Hg²⁺ recoveries ranging from 97% to 100%. Full article

Hazardous dyes in industrial wastewater are an internationally recognized issue for community health. Nanoparticles synthesized through green protocols are a fascinating research field with numerous applications. The current study mainly aimed to investigate the degradation of Congo red (CR) dye under UV light in the presence of H₂O₂ and the photocatalytic activity of copper oxide nanoparticles (CuONPs). For CuONP formation, Citrus maxima extract contains a high number of phytochemical constituents. The size of CuONPs ranges between 25 and 90 nm. The photocatalytic activity of CuONPs with the addition of H₂O₂ was observed and analyzed under UV light to eliminate CR dye. The UV light caused the decomposition of H₂O₂, which produced ·OH radicals. The results revealed a significant increment in dye degradation during the presence of H₂O₂. The effect of concentration on the degradation of the CR dye was also studied. The degradation pathway of organic pollutants was reputable from the hydroxy radical medicated degradation of CR. Advanced Oxidation Treatment depends on the in situ production of reactive ·OH species and is presented as the most effective procedure for decontamination. The biological activity of CuONPs was evaluated against Escherichia coli Bacillus subtillis, Staphylococcus aureus, Shigella flexenari, Acinetobacter Klebsiella pneumonia, Salmonella typhi and Micrococcus luteus. The newly synthesised nanomaterials showed strong inhibition activity against Escherichia coli (45%), Bacillus subtilis (42%) and Acinetobacter species (25%). The activity of CuONPs was also investigated against different fungus species such as: Aspergillus flavus, A. niger, Candida glabrata, T. longifusus, M. Canis, C. glabrata and showed a good inhibition zone against Candida glabrata 75%, Aspergillus flavus 68%, T. longifusus 60%. The materials showed good activity against C. glaberata, A. flavus and T. longifusus. Furthermore, CuONPs were tested for antioxidant properties using 2, 2 diphenyl-1-picrylhydrazyl) (DPPH). Full article