Search Results (50)

This work describes a non-enzymatic electrochemical glucose biosensor combining for the first time molecularly imprinted polymers (MIPs) for glucose concentration and gold nanoparticles (AuNPs) on screen-printed carbon electrodes (SPEs), where both MIPs and AuNPs were assembled in situ. Electrochemical impedance spectroscopy (EIS) was used to evaluate the analytical performance of the sensor, which has a linear range between 1.0 µM and 1.0 mM when standard solutions are prepared in buffer. Direct measurement of glucose was performed by chronoamperometry, measuring the oxidation current generated during direct glucose oxidation. The selectivity was tested against ascorbic acid and the results confirmed a selective discrimination of the electrode for glucose. Overall, the work presented here represents a promising tool for tracking glucose levels in serum. The use of glucose MIP on the electrode surface allows the concentration of glucose, resulting in lower detection limits, and the use of AuNPs reduces the potential required for the oxidation of glucose, which increases selectivity. In addition, this possible combination of two analytical measurements following different theoretical concepts can contribute to the accuracy of the analytical measurements. This combination can also be extended to other biomolecules that can be electrochemically oxidised at lower potentials. Full article

This study presents a structurally tunable Au-based solid polymer electrolyte (SPE) membrane electrode with significantly enhanced performance in organic hydrogenation reactions. Compared to a Pt-based counterpart, the Au-based electrode achieved a 277% increase in cyclohexane yield and a 4.8% reduction in hydrogen evolution during cyclohexene hydrogenation, demonstrating superior catalytic selectivity and energy efficiency. The improved performance is attributed to synergistic optimization of the electrode’s nanostructure and electronic properties. The Au-based electrode exhibited a 215% increase in specific surface area (SSA) relative to its initial state, along with a markedly enhanced electrochemical active surface area (ECSA). These enhancements stem from its mesoporous architecture, lattice contraction, and high density of zero-dimensional defects. X-ray photoelectron spectroscopy (XPS) revealed a negative shift in Au4f binding energy, a positive shift in Ni⁰ peaks, and an increased concentration of oxygen vacancies (Ov), indicating favorable modulation of the surface electronic structure. This reconstruction promotes H* adsorption and accelerates the hydrogenation reaction, serving as a key mechanism for catalytic enhancement. The core innovation of this work lies in the coordinated engineering of nanoscale structure and surface electronic states, enabling concurrent improvements in reaction rate, selectivity, and energy efficiency. These findings offer valuable guidance for designing noble metal-based membrane electrodes in advanced hydrogen energy conversion and storage systems. Full article

Methicillin-resistant Staphylococcus epidermidis (MRSE) contamination is commonly found on human skin and medical devices. Herein, we present a sensor utilizing molecularly imprinted polymer nanobodies (nanoMIP) for recognition and electrochemical impedance spectroscopy (EIS) to detect S. epidermidis. Sensor manufacturing involves synthesizing nanoMIP via solid-phase synthesis using whole bacteria as templates. Screen-printed gold electrode (AuSPE)-modified 16-mercaptohexadecanoic acid (MHDA) served to immobilize the nanoMIPs on the sensor surface through an amide bond, with the remaining functional groups blocked by ethanolamine (ETA). Scanning electron microscope (SEM) analysis of the modified AuSPE surface reveals immobilized spherical nanoMIP particles of 114–120 nm diameter, while atomic force microscope (AFM) analysis showed increased roughness and height compared to bare AuSPE. The sensor is selective for S. epidermidis, with a remarkable detection limit of 1 CFU/mL. This research demonstrates that the developed nanoMIP-based sensor effectively detects S. epidermidis. Further research will focus on developing protocols to integrate the nanoMIP-based EIS sensor into medical and industrial applications, ultimately contributing to improved safety for both humans and animals in the future. Full article

The quantitative determination of conotoxins has great potential in the development of natural marine peptide pharmaceuticals. Considering the time-consuming sample pretreatment and expensive equipment in MS or LC-MS/MS analysis, an electrochemical sensor combined with molecularly imprinted polymer (MIP) is fabricated for the rapid monitoring of conotoxin αB-VxXXIVA to promote its pharmaceutical value and eliminate the risk of human poisoning. Electrochemically reduced graphene oxide–gold composite (rGO-Au) is modified with chitosan (CS) and glutaraldehyde (GA) to immobilize the macromolecular peptide, conotoxin αB-VxXXIVA. Subsequently, acrylamide (AAM) with a cross-linking agent, N,N′-methylene-bisacrylamide (NNMBA), is introduced into the rGO-Au electrode to form MIPs by electro-polymerization. The proposed MIP-based electrochemical sensor, PAM/αB-CTX/CS-GA/rGO-Au/SPE, exhibits satisfactory sensing performance in the detection of αB-VxXXIVA. Based on current change versus logarithm concentration, a wide linear range from 0.1 to 10,000 ng/mL and a low detection limit (LOD) of 0.014 ng/mL for this sensor are obtained. This work provides a promising method in electrochemical determination combined with MIP for the determination of macromolecular peptides. Full article

A cutting-edge biosensor has been developed to monitor blood glucose levels, which is particularly vital for people with diabetes. This advanced technology uses a miniaturized and membraneless enzymatic fuel cell (EFC) as a compact electrical reader for rapid on-site diabetes diagnosis. Using disposable screen-printed gold electrodes (Au-SPE) modified with the enzyme glucose oxidase (GOx), the biosensor enables the oxidation of glucose at both the anode (counter electrode) and cathode (working electrode) of the EFC. The cathode contains graphene oxide/Prussian blue nanocubes (GO/PBNCs), while the anode uses a biographene layer. Both electrodes were modified with GOx by electrostatic/hydrogen bonding the enzyme to the modified electrodes surface. Individual evaluations of each electrode system emphasized their effectiveness. The integration of both electrodes resulted in an EFC that can generate an output power of approximately 1.8 μW/cm² at a glucose concentration of 5 mmol/L, which is very close to physiological conditions (3.8 to 6.9 mmol/L). This technology represents a significant advance and promises fully autonomous diagnostic devices suitable for a wide range of analytes. It paves the way for diagnostics everywhere and marks a fundamental shift in point-of-care (PoC) diagnostics. Full article

Monitoring potassium ion (K⁺) concentration is essential in veterinary medicine, particularly for preventing hypokalemia in dairy cows, which can severely impact their health and productivity. While traditional laboratory methods like atomic absorption spectrometry are accurate, they are also time-consuming and require complex sample preparation. Ion-selective electrodes (ISEs) provide an alternative that is faster and more suitable for field measurements, but their performance is often compromised under variable temperature conditions, leading to inaccuracies. To address this, we developed a novel screen-printed ion-selective electrode (SPE) with hydrophobic Ti₃C₂ Mxene and gold nanoparticles (AuNPs), integrated with a temperature sensor. This design improves stability and accuracy across fluctuating temperatures by preventing water layer formation and enhancing conductivity. The sensor was validated across temperatures from 5 °C to 45 °C, achieving a linear detection range of 10⁻⁵ to 10⁻¹ M and a response time of approximately 15 s. It also demonstrated excellent repeatability, selectivity, and stability, making it a robust tool for K⁺ monitoring in complex environments. This advancement could lead to broader applications in other temperature-sensitive analytical fields. Full article

Pseudomonas aeruginosa is a significant opportunistic pathogen highly prevalent in the environment, requiring early detection methods to prevent infections in vulnerable individuals. The most specific aptamer for P. aeruginosa, F23, has been used for the development of various assays and sensors for early diagnosis and monitoring. In this study, a novel F23-based electrochemical aptasensor was designed using disposal gold screen-printed electrodes (Au-SPEs) with high reproducibility. Methylene blue (MB) was used as an exogenous indicator, which significantly amplified the electrochemical signal and improved the sensitivity of detection. The aptasensor explored a limit of detection (LOD) of 8 CFU·mL⁻¹ and high selectivity for P. aeruginosa over other interfering bacteria. Furthermore, it showed potential to detect P. aeruginosa in tap water samples, offering a point-of-care tool for rapidly controlling the growth of this bacterium in various applications. Full article

The development of biosensors for determining the most diverse biomolecules is a constant focus of many research groups. There is a latent need to propose sensors that combine portability, simple measurements, and good analytical performance. Here, we propose an electrochemical immunosensor that is fully portable and energy-independent for diagnosing antibodies against SARS-CoV-2 (the virus that causes COVID-19). Initially, disposable screen-printed carbon electrodes (SPEs) were covered by gold microblobs (AuMBs), which were synthesized amperometrically from Au³⁺ ions. Then, the SPE-AuMBs were coated with cysteamine, which allowed the N-hydroxysuccinimide-activated SARS-CoV-2 antigen (spike protein) to be immobilized. The antigen-activated electrode was used to detect COVID-19 antibodies from current measurements obtained by differential pulse voltammetry. The AuMBs synthesis time was optimized, and the presence of gold structures improved the electrochemical responses of the SPE. It was possible to quantitatively determine antibodies in the concentration range of 0.25 to 10 µg mL⁻¹. This range includes concentrations found in biological fluids from patients at any stage of the disease. An analysis took approximately the same time as traditional rapid nasal tests (20 min) and costed less, considering all the steps necessary to prepare a disposable antigen-functionalized SPE. Full article

This study addresses the necessity to monitor the presence of glyphosate (Gly) in waters, highlighting the need for on-site detection of Gly by using electrochemical sensors in environmental and agricultural monitoring programs. Two approaches were employed: (1) modification with graphene decorated with gold nanoparticles (AuNPs-Gr) and dispersed in either dimethylformamide (DMF) or a solution containing Nafion and isopropanol (NAF), and (2) molecularly imprinted polymers (MIPs) based on polypyrrole (PPy) deposited on gold SPEs (AuSPE). Electrochemical characterization revealed that sensors made of AuNPs-Gr/SPCE exhibited enhanced conductivity, larger active area, and improved charge transfer kinetics compared to unmodified SPEs and SPEs modified with graphene alone. However, the indirect detection mechanism of Gly via complex formation with metallic cations in AuNPs-Gr-based sensors introduces complexities and compromises sensitivity and selectivity. In contrast, MIPPy/AuSPE sensors demonstrated superior performance, offering enhanced reliability and sensitivity for Gly analysis. The MIPPy/AuSPE sensor allowed the detection of Gly concentrations as low as 5 ng/L, with excellent selectivity and reproducibility. Moreover, testing in real surface water samples from the Olt River in Romania showed recovery rates ranging from 90% to 99%, highlighting the effectiveness of the detection method. Future perspectives include expanding the investigation to monitor Gly decomposition in aquatic environments over time, providing insights into the decomposition’s long-term effects on water quality and ecosystem health, and modifying regulatory measures and agricultural practices for mitigating its impact. This research contributes to the development of robust and reliable electrochemical sensors for on-site monitoring of Glyphosate in environmental and agricultural settings. Full article

Bisphenol A (BPA) has been classified as an endocrine-disrupting substance that may cause adverse effects on human health and the environment. The development of simple and sensitive electrochemical biosensors is crucial for the rapid and effective quantitative determination of BPA. This work presents a study on electrochemical sensors utilizing gold nanoparticle-modified multi-walled carbon nanotubes (CNT/AuNPs). Glassy carbon electrodes (GCEs) and screen-printed electrodes (SPEs) were conveniently modified and used for BPA detection. AuNPs were electrodeposited onto the CNT-modified electrodes using the galvanostatic method. The electrodes were properly modified and characterized by using Raman spectroscopy, cyclic voltammetry (CV), and electrochemical impedance analysis (EIS). The electrochemical response of the sensors was studied using differential pulse voltammetry (DPV) and constant potential amperometry (CPA) for modified GCE and SPE electrodes, respectively, and the main analytical parameters were studied and optimized. Problems encountered with the use of GCEs, such as sensor degradation and high limit of detection (LOD), were overcome by using modified SPEs and a flow injection device for the measurements. Under this approach, an LOD as low as 5 nM (S/N = 3) was achieved and presented a linear range up to 20 μM. Finally, our investigation addressed interference, reproducibility, and reusability aspects, successfully identifying BPA in both spiked and authentic samples, including commercial and tap waters. These findings underscore the practical applicability of our method for accurate BPA detection in real-world scenarios. Notably, the integration of SPEs and a flow injection device facilitated simplified automation, offering an exceptionally efficient and reliable solution for precise BPA detection in water analysis laboratories. Full article

Alcohol is a dangerous substance causing global mortality and health issues, including mental health problems. Regular alcohol consumption can lead to depression, anxiety, cognitive decline, and increased risk of alcohol-related disorders. Thus, monitoring ethanol levels in biological samples could contribute to maintaining good health. Herein, we developed an electrochemical sensor for the determination of ethanol in human salivary samples. Initially, the tetra-chloroauric acid (HAuCl₄) was chemically reduced using sparfloxacin (Sp) which also served as a stabilizing agent for the gold nanoparticles (AuNPs). As-prepared Sp-AuNPs were comprehensively characterized and confirmed by UV-visible spectroscopy, X-ray diffraction, field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and elemental mapping analysis. The average particle size (~25 nm) and surface charge (negative) of Sp-AuNPs were determined by using dynamic light scattering (DLS) and Zeta potential measurements. An activated screen-printed carbon electrode (A-SPE) was modified using Sp-AuNPs dispersion, which exhibited greater electrocatalytic activity and sensitivity for ethanol (EtOH) oxidation in 0.1 M sodium hydroxide (NaOH) as studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). DPV showed a linear response for EtOH from 25 µM to 350 µM with the lowest limit of detection (LOD) of 0.55 µM. Reproducibility and repeatability studies revealed that the Sp-AuNPs/A-SPEs were highly stable and very sensitive to EtOH detection. Additionally, the successful electrochemical determination of EtOH in a saliva sample was carried out. The recovery rate of EtOH spiked in the saliva sample was found to be 99.6%. Thus, the incorporation of Sp-AuNPs within sensors could provide new possibilities in the development of ethanol sensors with an improved level of precision and accuracy. Full article

In this study, we report the development of a technique to fabricate a screen-printed electrode (SPE) and apply it in uric acid sensing. The SPE was fabricated by printing it on a photo paper substrate using a printing technique on an office printer. In particular, the conductive ink used to print the working electrode (WE) and counter electrode (CE) consisted of graphene oxide (GO) and a gold nanorod (AuNR) material. While the reference electrode (RE) was made by applying a conductive silver paste to the fabricated SPE, the electrochemical measurement of uric acid solution using fabricated SPE GO/AuNR provided a higher signal than commercially available SPE. The electroanalytical performance of the fabricated SPE based on GO/AuNR, which was used to measure the uric acid solution, exhibited a linear range of 0.8−200 μM, a detection limit of 0.5 μM, a quantitation limit of 1.0 μM, an outstanding repeatability (% relative standard deviation) of 4.885%, and good selectivity with ascorbic acid, dopamine, glucose, urea, and sodium as interference. Furthermore, an SPE, fabricated based on GO/AuNR, was successfully employed for the determination of uric acid concentration in human urine samples using the standard addition approach. Full article

This study describes the use of electrochemical sensors to detect and quantify several statins (rosuvastatin and simvastatin) in pharmaceutical products. Two types of commercially screen-printed sensors were used and compared: one based on carbon (SPCE) and the other modified with gold nanoparticles and multi-walled carbon nanotubes (SPE/GNP-MWCNT). Cyclic voltammetry was employed for determination. The AuNP-MWCNTs/SPCE sensor outperformed the SPCE sensor, displaying excellent electrochemical properties. It demonstrated high sensitivity with low limits of detection (LOD) and quantification (LOQ) values: 0.15 µM and 5.03 µM, respectively, for rosuvastatin and 0.30 µM and 1.01 µM, respectively, for simvastatin. The sensor had a wide linear range of 20–275 µM for rosuvastatin and 50–350 µM for simvastatin. Using the AuNP-MWCNTs/SPCE sensor, rosuvastatin and simvastatin were successfully quantified in pharmaceutical products. The results were validated towards producer-reported values (standardized drugs) and a conventional analysis method (FTIR). The sensor exhibited excellent stability, reproducibility, and analytical recovery ranging from 99.3% to 106.6% with a low relative standard deviation (RSD) of less than 1%. In conclusion, the AuNP-MWCNTs/SPCE sensor proved to be a reliable and sensitive tool for detecting and quantifying statins in pharmaceutical products. Its superior electrochemical properties, low LOD and LOQ values, wide linear range, and high analytical recovery make it a promising choice for pharmaceutical quality control. Full article

In view of the presence of pathogenic Vibrio cholerae (V. cholerae) bacteria in environmental waters, including drinking water, which may pose a potential health risk to humans, an ultrasensitive electrochemical DNA biosensor for rapid detection of V. cholerae DNA in the environmental sample was developed. Silica nanospheres were functionalized with 3-aminopropyltriethoxysilane (APTS) for effective immobilization of the capture probe, and gold nanoparticles were used for acceleration of electron transfer to the electrode surface. The aminated capture probe was immobilized onto the Si-Au nanocomposite-modified carbon screen printed electrode (Si-Au-SPE) via an imine covalent bond with glutaraldehyde (GA), which served as the bifunctional cross-linking agent. The targeted DNA sequence of V. cholerae was monitored via a sandwich DNA hybridization strategy with a pair of DNA probes, which included the capture probe and reporter probe that flanked the complementary DNA (cDNA), and evaluated by differential pulse voltammetry (DPV) in the presence of an anthraquninone redox label. Under optimum sandwich hybridization conditions, the voltammetric genosensor could detect the targeted V. cholerae gene from 1.0 × 10⁻¹⁷–1.0 × 10⁻⁷ M cDNA with a limit of detection (LOD) of 1.25 × 10⁻¹⁸ M (i.e., 1.1513 × 10⁻¹³ µg/µL) and long-term stability of the DNA biosensor up to 55 days. The electrochemical DNA biosensor was capable of giving a reproducible DPV signal with a relative standard deviation (RSD) of <5.0% (n = 5). Satisfactory recoveries of V. cholerae cDNA concentration from different bacterial strains, river water, and cabbage samples were obtained between 96.5% and 101.6% with the proposed DNA sandwich biosensing procedure. The V. cholerae DNA concentrations determined by the sandwich-type electrochemical genosensor in the environmental samples were correlated to the number of bacterial colonies obtained from standard microbiological procedures (bacterial colony count reference method). Full article

Miniaturized and integrated devices for fast determination of clinical biomarkers are in high demand in the current healthcare environment. In this work, we present a functionalized self-assembled monolayer (SAM) on the gold surface of a screen-printed electrode (Au-SPE). The device was applied for uric acid (UA) detection, a biomarker associated with arthritis, diabetes mellitus, and kidney function. Prior to SAM formation, AuSPE was subjected to pretreatment with KOH and Au electrodeposition to provide additional roughness to the substrate. The SAM was formed in the AuSPE/KOH/AuNP surface by the cysteamine method—carried out for working surface dipping in the cysteamine (CYS) solution at 20 mM for 24 h (rinsed with ethanol and milli-Q water). Then, the uricase enzyme was immobilized through physical absorption at room temperature for 1 h to obtain the AuSPE/KOH/AuNPs/SAM/Uox biosensor. The physical and electrochemical characterization of AuSPE modification was carried out by scanning electron microscopy (SEM) and cyclic voltammetry (CV). The calibrated data of the Au/KOH/AuNPs/SAM/Uox biosensor showed a linear relation in the range of 50–1000 µM, a sensibility of 0.1449 µA/[(µM)cm²], and a limit of detection (LOD) of 4.4669 µM. The Au/KOH/AuNPs/SAM/Uox also exhibited good selectivity for UA in the presence of ascorbic acid. Moreover, the methodology showed good reproducibility, stability, and sensitive detection of UA. This performance of the proposed biosensor is in good accordance with clinical needs and can be compared with previous biosensors based on nanostructured surfaces of high-fabrication complexity. Full article