Search Results (203)

Room-temperature vulcanizing (RTV) silicone foams are used in many industrial applications that require the material to perform over long time periods. However, mechanical properties tend to deteriorate when these foams age under a compressive load. The chemical aging is attributed to the presence of unreacted functional groups of the prepolymers, residues from acid, and catalytically active tin (II) species. Here, an optimized thermal treatment of an RTV foam that achieves completion of curing reactions and deactivation of reactive species is proposed. Foams that were thermally aged for three months under compressive load showed no signs of compression set, indicative of the effectiveness of the implemented post-curing approach. In addition, the effects of fillers (diatomaceous earth, fumed silica, and carbon nanofibers) on thermomechanical properties were investigated. Tensile strength, tear strength, and thermal conductivity increased when these fillers were added to the unfilled RTV formulation, with carbon nanofibers (CNFs) being the most effective filler. Rheological studies of RTV formulations indicated that 2.5 wt.% of CNFs is the upper limit that can be added to the RTV formulation. Full article

To address mass transport limitations in carbon nanofiber membrane electrodes for overall water splitting, a self-supporting nitrogen-doped hollow carbon nanofiber membrane embedded with Co/Co₂P heterojunctions (Co/Co₂P-NCNFs-H) was fabricated via continuous coaxial electrospinning. The architecture features uniform hollow channels (200–250 nm diameter, 30–50 nm wall thickness) and a high specific surface area (254 m² g⁻¹), as confirmed by SEM, TEM, and BET analysis. The Co/Co₂P heterojunction was uniformly dispersed on nitrogen-doped hollow carbon nanofibers through electrospinning, leverages interfacial electronic synergy to accelerate charge transfer and optimize the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER). Electrochemical tests demonstrated exceptional catalytic activity, achieving current densities of 100 mA cm⁻² at ultralow overpotentials of 405.6 mV (OER) and 247.9 mV (HER) in 1.0 M KOH—surpassing most reported transition metal catalysts for both half-reactions. Moreover, the electrode exhibited robust long-term stability, maintaining performance for nearly 20 h at 0.6 V (vs. Ag/AgCl) (OER) and over 250 h at −1.5 V (vs. Ag/AgCl) (HER), attributed to the mechanical integrity of the hollow architecture and strong metal–carbon interactions. This work demonstrates that integrating hollow nanostructures (enhanced mass transport) and heterojunction engineering (optimized electronic configurations) creates a scalable strategy for designing efficient bifunctional catalysts, offering significant promise for sustainable hydrogen production via water electrolysis. Full article

This study presents a one-step electrospinning method to fabricate polyacrylonitrile (PAN) nanofibers embedded with green-synthesized silver nanoparticles (AgNPs) for efficient catalytic dye reduction and real-time monitoring. Utilizing avocado seed extract for AgNP synthesis, the resulting composite nanofibers exhibit uniform nanoparticle dispersion and enhanced surface area, significantly improving adsorption and catalytic properties. The membranes demonstrated outstanding catalytic activity, achieving over 95% degradation of methyl orange within 45 min when paired with sodium borohydride, and maintained structural integrity and performance over ten reuse cycles. The integration of a novel 3D-printed support enabled scalability, allowing a 60-fold increase in treatment volume without compromising efficiency. Additionally, the composite’s electrical conductivity changes enabled the real-time monitoring of the dye reduction process, highlighting its dual functionality as both catalyst and sensor. These results encourage the potential of PAN/AgNPs supported on a 3D-printed structure nanofiber membranes for scalable, sustainable wastewater treatment and in situ reaction monitoring. Full article

Chronic wounds, including diabetic foot ulcers and pressure sores, are becoming more prevalent due to aging populations and increased metabolic problems. These wounds often persist due to impaired healing, chronic inflammation, oxidative stress, and infections caused by multidrug-resistant pathogens, making conventional treatments—including antibiotics and antiseptics—largely inadequate. This creates an urgent need for advanced, biologically responsive therapies that can both combat infection and promote tissue regeneration. Probiotics have surfaced as a viable option owing to their capacity to regulate immune responses, impede pathogenic biofilms, and generate antibacterial and antioxidant metabolites. However, their clinical application is limited by poor viability, sensitivity to environmental conditions, and short retention at wound sites. Nanotechnology-based delivery systems address these limitations by protecting probiotics from degradation, enhancing site-specific delivery, and enabling controlled, stimuli-responsive release. Encapsulation techniques using materials like chitosan, PLGA, liposomes, nanogels, nanofibers, and microneedles have shown significant success in improving wound healing outcomes in preclinical and clinical models. This review summarizes the current landscape of chronic wound challenges and presents recent advances in probiotic-loaded nanotechnologies. It explores various nano-delivery systems, their mechanisms of action, biological effects, and therapeutic outcomes, highlighting the synergy between probiotics and nanocarriers as a novel, multifaceted strategy for managing chronic wounds. Full article

The widespread use of formaldehyde in both industrial and household products has raised significant health concerns, emphasizing the need for highly sensitive sensors to monitor formaldehyde concentrations in the environment in real time. In this study, we report the fabrication of a highly sensitive formaldehyde gas sensor based on Ag₂O and PtO₂ co-decorated LaFeO₃ nanofibers, prepared by electrospinning, with an ultra-low detection limit of 10 ppb. Operating at an optimal temperature of 210 °C, the sensor exhibits high sensitivity, with a response value of 283 to 100 ppm formaldehyde—nearly double the response of the Ag-only decorated LaFeO₃ sensor. Additionally, the sensor demonstrated good selectivity, repeatability, and long-term stability over 80 days. The enhanced sensitivity is attributed to the strong adsorption ability of Ag towards both oxygen and formaldehyde, Ag’s catalytic oxidation of formaldehyde, PtO₂’s catalytic action on oxygen, and the spillover effect of PtO₂ on oxygen. This sensor holds significant potential for environmental monitoring due to its ultrahigh sensitivity and ease of fabrication. Full article

This paper presents the effect of wood treatment with cellulose nanofibers on its parameters. The wettability, color changes (also after UV+IR radiation), equilibrium moisture content and mechanical parameters of wood treated with cellulose nanofibers (CNF) in three concentrations (0.5, 1 and 2%) were determined. Wood treatment with CNF increased the wettability of its surface, as evidenced by lower values of the contact angle (24.3–56.3 degrees) compared to untreated wood (98.3 degrees). The SEM images indicated the formation of cellulose nanofiber networks on the wood surface, especially in the case of 2% CNF-treated wood, which formed a well-adhered and homogenous film. Wood treated with 0.5% CNF showed a lower total color change (∆E*) value (1.9) after aging compared to untreated wood (2.9), indicating that the color changes in the treated wood were very small and recognizable only to an experienced observer, while the color differences in the control wood were recognizable to an inexperienced observer. Furthermore, CNF showed no negative effect on the strength parameters of the treated wood and only slightly affected the equilibrium moisture content for both sorption phases over the entire relative humidity range compared to control samples. The results prove the effective use of cellulose nanofibers in wood treatment, which can be an ecological and non-toxic component of wood protection systems. Full article

Carbon nanofibrous materials from electrospinning are good candidate electrode materials for supercapacitor applications due to their straightforward processability, chemical stability, high porosity, and large surface area. In this research, a straightforward and effective way was revealed to significantly enhance the electrochemical performance of carbon nanofibrous electrode material from electrospinning of polyacrylonitrile (PAN). Fluorination of the electrospun carbon nanofibers (ECNF) was studied by comparing two types of hydrofluoric acid (HF) treatment, i.e., direct HF acid treatment on ECNF (Type I) vs. HF acid treatment on the stabilized PAN (Type II) followed by carbonization. The latter was found to be an advantageous way to introduce C-F bonds in the resultant carbon nanofibrous electrode material that contributed to pseudocapacitance. Furthermore, the Type II HF acid treatment demonstrated exciting synergistic effects with ECNF aerogel formation on carbon structure and porosity development and generated a superior fluorinated electrospun carbon nanofibrous aerogel (ECNA-F) electrode material for supercapacitor uses. The resultant ECNA-F electrode material demonstrated excellent electrochemical performance with great cyclic stability due to the large improvements in both pseudocapacitance and electrical double-layer capacitance. ECNA-F achieved a specific capacitance of 372 F/g at a current density of 0.5 A/g with 1 M H₂SO₄ electrolyte, and the device with ECNA-F and 1 M Na₂SO₄ electrolyte possessed an energy density of 29.1 Wh/kg at a power density of 275 W/kg. This study provided insight into developing high-performance and stable carbon nanofibrous electrode materials for supercapacitors. Full article

GenX, the trade name of hexafluoropropylene oxide dimer acid (HFPO-DA) and its ammonium salt, is a short-chain PFAS that has emerged as a substitute for the legacy PFAS perfluorooctanoic acid (PFOA). However, GenX has turned out to be more toxic than people originally thought. In order to monitor and regulate water quality according to recently issued drinking water standards for GenX, rapid and ultrasensitive detection of GenX is urgently needed. For the first time, this study reports ultrasensitive (as low as 1 part per billion (ppb)) and fast detection (in minutes) of GenX in water via surface-enhanced Raman spectroscopy (SERS) using a hierarchical nanofibrous SERS substrate, which was prepared by assembling ~60 nm Ag nanoparticles on electrospun nylon-6 nanofibers through a “hot start” method. The findings in this research highlight the potential of the engineered hierarchical nanofibrous SERS substrate for enhanced detection of short-chain PFASs in water, contributing to the improvement of environmental monitoring and management strategies for PFASs. Full article

Peripheral nerve injury disrupts the function of the peripheral nervous system, leading to sensory, motor, and autonomic deficits. While peripheral nerves possess an intrinsic regenerative capacity, complete sensory and motor recovery remains challenging due to the unpredictable nature of the healing process, which is influenced by the extent of the injury, age, and timely intervention. Recent advances in microsurgical techniques, imaging technologies, and a deeper understanding of nerve microanatomy have enhanced functional outcomes in nerve repair. Nerve injury initiates complex pathophysiological responses, including Wallerian degeneration, macrophage activation, Schwann cell dedifferentiation, and axonal sprouting. Complete nerve disruptions require surgical intervention to restore nerve continuity and function. Direct nerve repair is the gold standard for clean transections with minimal nerve gaps. However, in cases with larger nerve gaps or when direct repair is not feasible, alternatives such as autologous nerve grafting, vascularized nerve grafts, nerve conduits, allografts, and nerve transfers may be employed. Autologous nerve grafts provide excellent biocompatibility but are limited by donor site morbidity and availability. Vascularized grafts are used for large nerve gaps and poorly vascularized recipient beds, while nerve conduits serve as a promising solution for smaller gaps. Nerve transfers are utilized when neither direct repair nor grafting is possible, often involving re-routing intact regional nerves to restore function. Nerve conduits play a pivotal role in nerve regeneration by bridging nerve gaps, with significant advancements made in material composition and design. Emerging trends in nerve regeneration include the use of 3D bioprinting for personalized conduits, gene therapy for targeted growth factor delivery, and nanotechnology for nanofiber-based conduits and stem cell therapy. Advancements in molecular sciences have provided critical insights into the cellular and biochemical mechanisms underlying nerve repair, leading to targeted therapies that enhance axonal regeneration, remyelination, and functional recovery in peripheral nerve injuries. This review explores the current strategies for the therapeutic management of peripheral nerve injuries, highlighting their indications, benefits, and limitations, while emphasizing the need for tailored approaches based on injury severity and patient factors. Full article

This study focuses on preparing piezoelectric polyvinylidene fluoride (PVDF) nanocomposites reinforced with silver nanoparticles (AgNPs) using an electrospinning process. The aim of this study is to assess AgNPs’ influence on the piezoelectric properties of PVDF and, therefore, create an optimal piezoelectric composite with enhanced properties, enabling its application in various fields both as sensor and actuator. Because electrical stimuli have proven to have a positive influence in tissue engineering, combined with AgNPs, which have antimicrobial properties, these composites demonstrate a promising opportunity for application as biomedical scaffolds. The proposed scaffolds were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy. In addition, mechanical properties are studied through tensile tests, while piezoelectric response is measured on an in-house built setup coupling mechanical stimuli and electrical response monitoring. An experimental test was combined with numerical simulations through the COMSOL Multiphysics version 6.3 software package, and this paper also presents a short review of the numerical and analytical methods used for the modelling and simulation of piezoelectric composites. Full article

Piezoelectric materials based on polyvinylidene fluoride (PVDF) are widely regarded as ideal candidates for the fabrication of piezoelectric energy harvesters (PEHs). However, the relatively low power output of PVDF limits its widespread application and poses a significant challenge to the advancement of PEHs. To address this issue, we have designed a novel PEH using silver-modified lead zirconate titanate/PVDF (pPZT@Ag/PVDF), which achieves a remarkable balance between high output performance and long-term stability. The pPZT@60Ag/PVDF PEH generates a peak voltage of 14.33 V, which is about 2.6 times that of the pure lead zirconate titanate/PVDF (pPZT/PVDF) PEH. This enhancement is attributed to the confined structure within the PVDF fibers, as well as the enhancement in dipole orientation alignment and the local electric field induced by silver nanoparticle modification. Furthermore, the pPZT@60Ag/PVDF PEH demonstrates a peak power density of 0.58 μW/cm², with negligible degradation in output voltage after 6000 bending cycles, and efficiently harvests mechanical energy from human movement. This study presents an effective method for fabricating high-performance PEHs, which is expected to advance the development of next-generation energy harvesting devices. Full article

Tendinopathy is a prevalent musculoskeletal condition that affects both aging populations and individuals involved in repetitive, high-intensity activities, such as athletes. Current treatment options primarily address symptom management or involve surgery, which carries a significant risk of complications and re-injury. This highlights the need for regenerative medicine approaches that combine stem cells, biomaterials, and growth factors. However, achieving effective tenogenic differentiation remains challenging due to the absence of standardized differentiation protocols. Consequently, a review of existing research has been conducted to identify optimal biomaterial properties and growth factor protocols. Findings suggest that the ideal biomaterial for tenogenic differentiation should feature a 3D structure to preserve tenogenic expression, incorporate a combination of aligned micro- and nanofibers to promote differentiation, and require further investigation into optimal stiffness. Additionally, growth factor protocols should include an induction phase to initiate tenogenic lineage commitment, followed by a maintenance phase to support matrix production and maturation. Full article

Visible-light-responsive silver-phosphate-sensitized fly-ash particles loaded on polyurethane nanofiber (Ag₃PO₄–FA/PU NFs) membrane photocatalysts were prepared by electrospinning followed by an ion-exchange method and characterized with state-of-art techniques. With the assistance of Ag₃PO₄–FA/PU NFs, 98 % of methylene blue (MB) was degraded within 60 min. The combination of FA and Ag₃PO₄ particles provided simultaneous adsorption and degradation of MB in an aqueous solution, resulting in the fast removal of the dye. Also, the Ag₃PO₄–FA/PU NFs exhibited excellent antibacterial performance toward Escherichia coli and Staphylococcus aureus bacteria. Thus, the prepared photocatalyst may provide a potential outcome for environmental remediation, especially wastewater treatment applications. Full article

Solar-driven catalytic oxidation processes for the removal of toxic gaseous pollutants have attracted considerable scientific attention, and there is a strong desire to improve the mass transfer, photogenerated charge separation, and O₂ activation by regulating the structure of the photocatalyst. Initially, functionalized graphene–TiO₂ mesoporous hollow nanofibers have been controllably fabricated by a coaxial electrospinning technique, in which functionalized graphene is controllably prepared through a sequential diazonium functionalization and silane modification and ensures its uniform distribution among TiO₂ nanoparticles (NPs). Subsequently, the ultrafine Ag NPs are primarily anchored onto the surface of graphene by an in situ frozen photodeposition strategy, producing Ag/functionalized graphene–TiO₂ mesoporous hollow nanofibers (Ag/SiG-TO MPHNFs). The optimal Ag/SiG-TO MPHNFs exhibit 3.9-fold and 4.6-fold enhancements in CO photooxidation compared with TO MPHNFs and P25 TiO₂, respectively. The enhanced photoactivity can be attributed to three factors: the creation of the mesoporous hollow structure accelerates mass transfer, the incorporation of graphene facilitates the transfer of photogenerated electrons from TiO₂ to graphene, and the anchoring of Ag NPs improves O₂ activation. Full article

Complex wounds pose a significant healthcare challenge due to their susceptibility to infections and delayed healing. This study focuses on developing electrospun polycaprolactone (PCL) nanofiber membranes coated with Type I collagen derived from bovine skin and functionalized with silver nanoparticles (AgNPs) to address these issues. The collagen coating enhances biocompatibility, while AgNPs synthesized through chemical reduction with sodium citrate provide broad-spectrum antimicrobial properties. The physical properties of the membranes were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Results showed the formation of nanofibers without defects and the uniform distribution of AgNPs. A swelling test and contact angle measurements confirmed that the membranes provided an optimal environment for wound healing. In vitro biological assays with murine 3T3 fibroblasts revealed statistically significant (p ≤ 0.05) differences in cell viability among the membranes at 24 h (p = 0.0002) and 72 h (p = 0.022), demonstrating the biocompatibility of collagen-coated membranes and the minimal cytotoxicity of AgNPs. Antibacterial efficacy was evaluated against Staphylococcus aureus (SA), Pseudomonas aeruginosa (PA), and Vancomycin-resistant Enterococcus (VRE), with the significant inhibition of biofilm formation observed for VRE (p = 0.006). Overall, this novel combination of collagen-coated electrospun PCL nanofibers with AgNPs offers a promising strategy for advanced wound dressings, providing antimicrobial benefits. Future in vivo studies are warranted to further validate its clinical and regenerative potential. Full article