Search Results (174)

This study optimizes the production of activated carbons from hydrothermally carbonized (HTC) biomass using potassium hydroxide (KOH) and phosphoric acid (H₃PO₄) as activating agents. A 2³ factorial experimental design evaluated the effects of agent-to-precursor ratio, dry impregnation time, and activation duration on mass yield and iodine adsorption capacity. KOH-activated carbons achieved superior iodine numbers (up to 1289 mg/g) but lower mass yields (18–35%), reflecting enhanced porosity at the cost of material loss. Conversely, H₃PO₄ activation yielded higher mass retention (up to 54.86%) with moderate iodine numbers (up to 1117.3 mg/g), balancing porosity and yield. HTC pretreatment at 190 °C reduced the ash content, thereby enhancing the stability of hydrochar. These findings highlight the trade-offs between adsorption performance and process efficiency, with KOH suited for high-porosity applications (e.g., water purification) and H₃PO₄ for industrial scalability. The study advances biomass waste valorization, aligning with circular economy principles and offering sustainable solutions for environmental and industrial applications, such as water purification and energy storage. Full article

The feasibility of utilizing biochar as a static floating material for agricultural applications was researched to prevent evaporation from open water static storage systems or as a floating barrier in slurry pits, for instance. Five types of biochar were created from chips, bark, and pellets of pine and residues from two acacia species using a pyrolysis time between 60 and 120 min and mean temperatures between 380 and 690 °C in a simple double-chamber reactor. Biomass and biochar were characterized for their main properties: bulk density, moisture content, volatile matter, ash content, fixed carbon, and pH. Biochar was also evaluated through a basic floatability test over 27 days (648 h) in distilled water. The highest fixed carbon content was observed in pine bark biochar (69.5%), followed by the pine pellets (67.4%) and pine chips (63.4%). Despite their high carbon content, the pellets exhibited a low floatability level, whereas pine bark biochar showed superior static floatage times, together with chip and ground chip biochar. These results suggest that biochar produced from bark and wood chips may be suitable for application as floatability material in water or slurry management systems. These results warrant further research into the static floating of biochar. Full article

This research aimed to evaluate the biological resistance to xylophagous organisms and the dimensional stability related to water absorption in plastic wood panels manufactured by compression molding and produced with pine wood and recycled thermoplastics. The wood–plastic composites (WPCs) were prepared from 50% pine sawdust and 50% recycled plastics (polyethylene terephthalate-PET, high-density polyethylene-HDPE, and polypropylene-PP). The thickness swelling test was carried out by immersing of the WPC samples in water at room temperature (25–30 °C) and evaluating the total change in WPC thickness after 1500 h (≈9 weeks or two months). In addition, the coefficient of initial swelling was evaluated to verify the variability of the swelling. For the biological resistance evaluation of the WPCs, tests were carried out with soil or arboreal termites (Nasutitermes corniger) and drywood termites (Cryptotermes brevis). The WPC loss of mass and termite mortality were evaluated. The use of PP promoted the best response to thickness swelling. The simple mathematical model adopted offers real predictions to evaluate the thickness of the swelling of the compounds in a given time. For some variables there were no statistical differences. It was shown that treatment 3 (T3) presented visual damage values between 0.4 for drywood termites and 9.4 for soil termites, in addition to 26% termite mortality, represented by the lowest survival time of 12 days. The developed treatments have resistance to termite attacks; these properties can be an important starting point for its use on a larger scale by the panel industries. Full article

Beer production produces significant amounts of brewers’ spent grain (BSG), a lignocellulosic by-product with important environmental and economic impacts. Despite its high moisture content and rapid microbial breakdown, BSG has a stable, nutrient-rich composition, especially high in protein, fiber, and polyphenolic compounds. While its perishability limits direct use in food systems, BSG is often repurposed as livestock feed. Recent advances in bioprocessing and extraction technologies have expanded their use across different sectors. This review explores the composition of crude BSG and evaluates innovative valorization methods, including recovering bioactive compounds with pharmaceutical and nutraceutical value, and converting them into biofuels such as biogas, biodiesel, and bioethanol. Special focus is given to methods involving enzymatic hydrolysis, fermentation, and chemical extraction to isolate proteins, peptides, amino acids, sugars, and polyphenols. By analyzing emerging applications and industrial scalability challenges, this review highlights BSG’s growing role within circular economy models and its potential to promote sustainable innovations in both the brewing industry and the wider bioeconomy. Full article

This review examines sustainable cascading biorefinery strategies for the green alga Ulva, which is globally prevalent in eutrophic marine waters and often forms extensive “green tides.” These blooms cause substantial environmental and economic damage to coastal communities. The primary target products within an Ulva biorefinery typically encompass salts, lipids, proteins, cellulose, and ulvan. Each of these components possesses unique properties and diverse applications, contributing to the economic robustness of the biorefinery. Salts can be repurposed for agricultural or even human consumption. Lipids offer high-value applications in nutraceuticals and animal feed. Proteins present significant potential as plant-based nutritional supplements. Cellulose can be transformed into various advanced materials. Finally, ulvan, a polyanionic oligosaccharide unique to Ulva, holds promise due to its distinct properties, particularly in the biomedical field. Furthermore, state-of-the-art chemical modifications of ulvan are presented with the aim of tailoring its properties and broadening its potential applications. Future research should prioritize optimizing these integrated extraction and fractionation processes. Furthermore, a multi-product biorefining approach, integrated with robust Life Cycle Assessment studies, is vital for transforming this environmental challenge into a significant opportunity for sustainable resource valorization and economic growth. Full article

This study explored the production and activation of biochar from rice straw residue for dye adsorption applications. Rice straw, a widely available but underutilized biomass, was processed to isolate lignin and generate biochar through pyrolysis at 450 °C and 550 °C. Activation using chemical agents (e.g., KOH and NaOH) was performed to enhance surface area and porosity. Among the tested conditions, KOH activation at a char-to-agent ratio of 1:3 produced activated carbon at 800 °C with the highest BET surface area (835.2 m²/g), and high fixed carbon (44.4%) after HCl washing. Thermogravimetric analysis was used to investigate pyrolysis kinetics, with activation energies determined using the Kissinger, Flynn–Wall–Ozawa, and Kissinger–Akahira–Sunose models. The brown solid showed a higher activation energy (264 kJ/mol) compared to isolated lignin (194 kJ/mol), indicating that more energy is required for decomposition. The AC was evaluated for the adsorption of methylene blue (MB) and methyl orange (MO) from aqueous solutions. Both dyes followed the Langmuir isotherm model, indicating that monolayer adsorption occurred. The maximum adsorption capacities reached 222 mg/g for MB and 244 mg/g for MO at 303 K, with higher values at elevated temperatures. Adsorption followed a pseudo-second-order kinetic model and was governed by a physisorption mechanism, as supported by thermodynamic analysis (ΔH < 20 kJ/mol and E_a < 40 kJ/mol). These findings demonstrate that KOH-activated biochar from rice straw residue is a high-performance, low-cost adsorbent for dye removal, contributing to sustainable biomass utilization and wastewater treatment. Full article

This study investigates biochar-enriched organic fertilizers made from bagasse, ash, spent wash, and cane tops, assessing their impact on corn growth over 45 days. A randomized complete block design with three replicates was used, testing six formulations with biochar levels at 0%, 10%, and 20%, along with soil-only and commercial fertilizer controls. Treatments T5 (bagasse + ash + spent wash + cane tops), T11 (T5 + 10% biochar), and T17 (T5 + 20% biochar) showed the best results for plant height, leaf development, and biomass production, with T17 performing the best for growth, biomass, and girth. The biochar in T17 had a pH of 9.37 ± 0.16, 18.00 ± 1.25% ash content, and a surface area of 144.58 m²/g. Nutrient analysis of the compost showed 2.85% potassium, 1.12% phosphorus, 1.85% nitrogen, 4.1% calcium, 0.23% magnesium, and 130 mg/kg zinc. The elemental composition was 68.50% carbon, 4.50% hydrogen, 6.00% nitrogen, and 25.30% oxygen, with 85.00% total organic carbon (TOC). This study concludes that T17 is the most effective formulation, offering both environmental and financial benefits, with composting potentially generating $11.16 million in profit, compared to the $19.32 million spent annually on waste management in Sri Lanka’s sugar industry. Full article

Biomass gasification is an effective process for converting organic wastes into syngas. Syngas is a biofuel that possesses several potential applications in the energy sector. However, the major bottleneck for the commercialization of this technology is tar production in biomass gasification, which affects gasifier performance and syngas yield/quality. Tar can be destructed by adopting in situ or ex situ modes of utilizing catalysts in biomass gasification. The added advantage of tar reduction is enhanced syngas energy content. Despite their advantages, catalysts face challenges such as high costs, declining performance over time, and difficulties in regeneration and recycling. Deactivation can also occur due to poisoning, fouling, and carbon buildup. While some natural materials have been tested as alternative materials, the financial sustainability and affordability of catalysts remain crucial for large-scale syngas production. This paper offers an overview of tar reduction strategies and the role of various catalysts in the gasification process and future perspectives on catalyst development for biomass gasification. Full article

Biomass liquefaction is a promising thermochemical route to convert lignocellulosic residues into bio-oil. This study evaluates the liquefaction behavior of 13 biomasses with varying particle sizes (0.3–2.0 mm) and moisture contents (5–11%) under mild solvolysis conditions. High-performance liquid chromatography (HPLC-RID) and thermogravimetric analysis (TGA) were used to characterize bio-oil composition and biomass properties, respectively. Maximum conversion (72%) was achieved for Miscanthus, while Ulva lactuca reached only 23% due to its low carbohydrate content. Hemicellulose-rich feedstocks showed higher yields, whereas high lignin content generally reduced conversion. Furfural was the main compound identified in the aqueous phase (up to 51 g/L), reflecting extensive pentose degradation. Laboratory and industrial-scale liquefaction of cork and eucalyptus revealed scale-dependent differences. Industrial cork bio-oil showed increased xylose (0.70 g/L) and furfural (0.40 g/L), while industrial eucalyptus exhibited elevated levels of acetic (0.46 g/L) and formic acids (0.71 g/L), indicating enhanced deacetylation and demethoxylation reactions. These findings offer valuable insights for optimizing feedstock selection and process conditions in biomass liquefaction. The valorization of lignocellulosic residues into bio-oil contributes to the development of scalable, low-carbon technologies aligned with circular economy principles and bio-based industrial strategies. Full article

Tomato waste (TW) was employed as a sustainable source for the synthesis of fluorescent carbon dots (CDs) via a microwave-assisted hydrothermal carbonization (Mw-HTC) method, aiming at its valorization. Several amines were used as nitrogen additives to enhance the fluorescence quantum yield (QY) of CDs, and a set of reaction conditions, including additive/TW mass ratio (0.04–0.32), dwell time (15–60 min), and temperature (200–230 °C) of the HTC process, were scrutinized. The structural analysis of the tomato waste carbon dots (TWCDs) was undertaken by FTIR and ¹H NMR techniques, revealing their most relevant features. In solid state, transmission electron microscopy (TEM) analysis showed the presence of nearly spherical nanoparticles with an average lateral size of 8.1 nm. Likewise, the topographical assessment by atomic force microscopy (AFM) also indicated particles’ heights between 3 and 10 nm. Their photophysical properties, revealed by UV–Vis, steady-state, and time-resolved fluorescence spectroscopies, are fully discussed. Higher photoluminescent quantum yields (up to 0.08) were attained when the biomass residues were mixed with organic aliphatic amines during the Mw-HTC process. Emission tunability is a characteristic feature of these CDs, which display an intensity average fluorescence lifetime of 8 ns. The new TWCDs demonstrated good antioxidant properties by the ABTS radical cation method (75% inhibition at TWCDs’ concentration of 5 mg/mL), which proved to be related to the dwell time used in the CDs synthesis. Moreover, the synthesized TWCDs suppressed the growth of Escherichia coli and Staphylococcus aureus at concentrations higher than 2000 μg/mL, encouraging future antibacterial applications. Full article

This study investigates the competitive dynamics of reducing sugar production and degradation during the subcritical water processing (SWP) of lyophilized grape pomace (LGP), with the goal of optimizing sugar yield. Under the SWP conditions tested (150 °C, 150 bar, pH 7, S/F of 30 g water g⁻¹ LGP, and a flow rate of 5 mL min⁻¹), we achieved a reducing sugar yield of 296.0 mg sugars g⁻¹ LGP, effectively balancing sugar production and degradation. Sugar yield decreased as the temperature increased from 150 °C to 210 °C, due to the degradation of monosaccharides into by-products like furfural and 5-HMF. A first-order reaction model was developed to better understand the kinetic competition between sugar formation and degradation at varying temperatures. The highest sugar yield occurred at 150 °C, where sugar production was maximized, and degradation was minimized. These findings offer valuable insights for subcritical water processing in the valorization of LGP into fermentable sugars while minimizing the formation of undesirable by-products. Full article

This study investigates the potential of biochars derived from agricultural waste biomass for the removal of heavy metal ions from aqueous solutions. Biochars were produced via slow pyrolysis at 793 K using almond shells (AS), walnut shells (WS), pistachio shells (PS), and rice husks (RH) as feedstocks. The physicochemical properties and adsorption performance of the resulting materials were evaluated with respect to Cd(II), Mn(II), Co(II), Ni(II), Zn(II), total Iron (Fe_tot), total Arsenic (As_tot), and total Chromium (Cr_tot) in model solutions. Surface morphology, porosity, and surface chemistry of the biochars were characterized by scanning electron microscopy (SEM), nitrogen adsorption at 77 K (for specific surface area and pore structure), Fourier-transform infrared spectroscopy (FTIR), and determination of the point of zero charge (pH_pzc). Based on their textural properties, biochars derived from WS, PS, and AS were classified as predominantly microporous, while RH-derived biochar exhibited mesoporous characteristics. The highest Brunauer–Emmett–Teller (S_BET) surface area was recorded for PS biochar, while RH biochar showed the lowest. The pistachio shell biochar exhibited the highest specific surface area (440 m²/g), while the rice husk biochar was predominantly mesoporous. Batch adsorption experiments were conducted at 25 °C, with an adsorbent dose of 3 g/L and a contact time of 24 h. The experiments in multicomponent systems revealed removal efficiencies exceeding 87% for all tested metals, with maximum values reaching 99.9% for Cd(II) and 97.5% for Fe_tot. The study highlights strong correlations between physicochemical properties and sorption performance, demonstrating the suitability of these biochars as low-cost sorbents for complex water treatment applications. Full article

In response to significant environmental challenges, biochar has garnered attention for its applications across diverse fields. Characterized by high carbon content resulting from the thermal degradation of biomass, biochar offers a sustainable strategy for waste valorization and environmental remediation. This paper offers a comprehensive overview of biochar production from residual biomass, emphasizing feedstock selection, conversion pathways, material properties, and application potential. Key production techniques, including pyrolysis, gasification, and hydrothermal carbonization, are critically evaluated based on operational conditions, energy efficiency, product yield, and environmental implications. The functional performance of biochar is further discussed in the context of soil enhancement, wastewater treatment, renewable energy generation, and catalytic processes, such as biohydrogen production. By transforming waste into value-added products, biochar technology supports circular economy principles and promotes resource recovery. Ongoing research aimed at optimizing production processes and understanding application-specific mechanisms is crucial to fully realizing the environmental potential of biochar. Full article

The objective of this study was to explore the potential of creating advanced insulating biocomposites using waste almond and hazelnut shells as particulate fillers, combined with a geopolymer binder, to develop sustainable materials with minimal environmental impact. Optimal conditions for the preparation of biocomposites were determined by measuring the compressive strengths. The aforementioned optimal conditions included a geopolymer to waste nutshell mass ratio of 2, room-temperature curing, and the use of metakaolin geopolymers activated with potassium solutions. Notably, the highest compressive strengths of 4.1 MPa for hazelnut shells biocomposite and 6.4 MPa for almond shells biocomposite were obtained with milk of lime pretreatment at 80 °C for 1 h. Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX) and Fourier transform infrared spectroscopy (FTIR) analyses revealed better adhesion, as well as improved geopolymer gel polymerization. Furthermore, thermal conductivity and diffusivity measurements demonstrated values characteristic of insulating materials, reinforcing their potential for eco-friendly construction applications. Full article