Search Results (27)

Wood ash is a promising supplementary cementitious material (SCM) due to its inherent pozzolanic properties. Intensive grinding has been shown to enhance this aspect and reduce the negative effects of variability in the chemical composition. This study investigated the influence of grinding through ball milling on the pozzolanic properties of wood ash. Four different types of wood ash were studied, each subjected to grinding durations of 10 and 20 min. Coal fly ash was used as a reference material. The pozzolanic activity of raw and ground wood ashes was evaluated using the strength activity index (SAI), the Frattini test, the R3 test, thermogravimetric analysis (TGA/DTG), X-ray diffraction (XRD) analysis, and scanning electron microscopy with energy-dispersive spectroscopy (SEM/EDS). The results indicated that both 10 min and 20 min grinding durations enhanced the reactivity and compressive strength. However, the 10 min grinding duration showed better overall performance than 20 min grinding, likely due to reduced agglomeration and more effective particle refinement. For calcium-rich wood ashes, the reactivity was linked to the hydraulic properties rather than the pozzolanic properties. Full article

This study determined how replacing sodium nitrate-based antifreeze admixture (AF) with belite-calcium sulfoaluminate (belite-CSA) cement affects the early age properties of ecological concretes based on ordinary Portland cement (OPC) and ground granulated blast-furnace slag (GGBFS). Concrete specimens were cured at −15 °C and treated in various ways before testing, i.e., no treatment, stored at 20 °C for 12 and 24 h. Generally, the addition of belite-CSA cement shortened the setting time due to the rapid formation of ettringite. The incorporation of 25 wt% of antifreeze admixture (AF) to the OPC-GGBFS concrete cured at −15 °C partially inhibited ice formation and enabled the continuation of hydration processes. This trend was observed for all samples, independent of the applied AF after freezing curing. On the contrary, the addition of 20 wt% of CSA failed to inhibit the ice formation and increased the risk of frost damage for concretes despite the treatment after freezing. These concrete specimens had lower hydration, lower strength, and a more porous binder matrix. The microstructure of the binder matrix was significantly affected by the amount of CSA and extreme negative curing, followed by no notable recovery post-curing at room temperature. Therefore, pre-curing at room temperature for at least 6 h has the potential to avoid frost damage. Concrete containing 25 wt% AF combined with 12 h and 24 h of curing at 20 °C after removal from freezing and prior to testing could enhance the compressive strengths of all concretes. The renewed hydration was indicated as the main influencing factor. Full article

Cement production contributes significantly to carbon dioxide emissions. Alkali-activated materials offer an environmentally friendly alternative due to their comparable strength, durability and low-carbon emissions while utilizing wastes and industrial by-products. Wood ash is a waste material that shows promising results as a partial replacement for Portland cement and precursors in alkali-activated systems. The aim of this study was to examine the effect of ground wood ash on the mechanical properties of alkali-activated mortars. Wood ash was incorporated as a 0 wt%, 10 wt% and 20 wt% partial replacement for ground granulated blast furnace slag (GGBFS). The wood ashes were ground in a planetary ball mill for 10 and 20 min. Sodium silicate (Na₂SiO₃), sodium carbonate (Na₂CO₃), and sodium hydroxide (NaOH) were used as alkali activators. The results demonstrated that ground wood ash improved the mechanical properties of alkali-activated systems compared to untreated wood ash. However, the incorporation of wood ash increased the porosity of the binder matrix. Full article

The thickness and properties of brash ice are usually compared with the properties of the surrounding level ice. The differences between these ice types are important to understand since the consolidated brash ice layer is typically assumed to have the same properties as level ice. Therefore, significant effort in the measurement campaign during the winters of 2020–2021, 2021–2022, and 2023 was made to develop a better understanding of the full-scale brash ice channel development. The channels were located near the shore in the Bay of Bothnia, Luleå, Sweden. The main parameters investigated were the snow, slush, and total ice thicknesses, including ice formed from freezing water and from freezing slush as well as the ice microstructure and strength. To our knowledge, this is the first paper to report the influence of snow in brash ice channels. It was observed that a significant amount of snow covered the brash ice channels between the ship passages. After each ship passage, the snow was submerged and formed slush-filled voids, which thereafter transformed into snow ice (SI) clusters frozen together with columnar ice. The SI content in the brash ice and side ridges was estimated from image analyses. The analyses showed that the snow ice content was 73% in level ice in the vicinity of the ship channel, 58% in the side ridges of the channel, and 21% in the middle of the test channel, whereas in the main channel, the SI contents were 54%, 43%, and 41% in each location, respectively. Full article

Concrete technology is becoming more and more sustainable and ecological following more extensive and focused research. The usage of industrial waste and by-products, such as steel ground granulated blast-furnace slag (GGBFS), mine tailing, fly ash, and recycled fibers, is a very important step toward a good transition of concrete into a “green” future and significant improvement in waste management in the world. However, there are also several known durability-related problems with some types of eco-concretes, including exposure to fire. The general mechanism occurring in fire and high-temperature scenarios is broadly known. There are many variables that weightily influence the performance of this material. This literature review has gathered information and results regarding more sustainable and fire-resistant binders, fire-resistant aggregates, and testing methods. Mixes that utilize industrial waste as a total or partial cement replacement have been consistently achieving favorable and frequently superior outcomes when compared to conventional ordinary Portland cement (OPC)-based mixes, especially at a temperature exposure up to 400 °C. However, the primary emphasis is placed on examining the impact of the matrix components, with less attention given to other factors such as sample treatment during and following exposure to high temperatures. Furthermore, there is a shortage of established standards that could be utilized in small-scale testing. Full article

Different ecological binders have been used to minimize the negative effects of cement production and use on the environment. Wood ash is one of these alternative binders, and there has been increasing research related to this topic recently. The wood ash utilized in the literature primarily originates from power plants and local bakeries, and predominantly wood fly ash is used. This review paper examines the use of wood ash as an ecological binder in two different applications: as a cement replacement and as an alkali-activated material. Studies have shown that while increased wood ash content in concrete and mortars can have negative effects on strength and durability, it is still a promising and developable material. Depending on the chemical composition of the wood ash, the strength and durability properties of concrete might be slightly improved by utilizing wood ash as a replacement for cement, with an optimal replacement level of 10–20%. However, there is a need for more research regarding the effects of wood ash on the durability of cement-based materials and its use in alkali-activated materials. Overall, this review provides a comprehensive overview of the properties of wood ash and its potential applications in conventional concrete and mortars, as well as in alkali-activated materials. Full article

Concrete is one of the most common building materials in the Northern Periphery and Arctic, and therefore we should pay attention to its quality while reducing its carbon footprint. The concrete industry has established many measures to limit greenhouse gas emissions from concrete, as stated in the environmental product declaration (EPD). The most significant contributor is cement (common dose between 250 and 600 kg per 1 m³ of concrete) in a concrete binder. Aside from the use of alternative fuels for cement production, new alternative materials for cement replacement are being sought. Those materials are called supplementary cementitious materials and mainly originate from industrial waste streams. Some of the materials are already standard and limited by the maximum allowed replacement, and some are new and still under investigation. The benefits and limitations of low-carbon concrete regulations in Norway, Sweden, Iceland, and Finland are demonstrated on three different concrete mixes in this article. The sorting of a reference mix and two low-carbon concrete mixes according to 4 different systems showed the informative character of the Icelandic system and the underestimation of possibilities for the carbon footprint of concrete in the Swedish classification system. Full article

Developing accurate and interpretable models to forecast concrete’s self-healing behavior is of interest to material engineers, scientists, and civil engineering contractors. Machine learning (ML) and artificial intelligence are powerful tools that allow constructing high-precision predictions, yet often considered “black box” methods due to their complexity. Those approaches are commonly used for the modeling of mechanical properties of concrete with exceptional accuracy; however, there are few studies dealing with the application of ML for the self-healing of cementitious materials. This paper proposes a pioneering study on the utilization of ML for predicting post-fire self-healing of concrete. A large database is constructed based on the literature studies. Twelve input variables are analyzed: w/c, age of concrete, amount of cement, fine aggregate, coarse aggregate, peak loading temperature, duration of peak loading temperature, cooling regime, duration of cooling, curing regime, duration of curing, and specimen volume. The output of the model is the compressive strength recovery, being one of the self-healing efficiency indicators. Four ML methods are optimized and compared based on their performance error: Support Vector Machines (SVM), Regression Trees (RT), Artificial Neural Networks (ANN), and Ensemble of Regression Trees (ET). Monte Carlo analysis is conducted to verify the stability of the selected model. All ML approaches demonstrate satisfying precision, twice as good as linear regression. The ET model is found to be the most optimal with the highest prediction accuracy and sufficient robustness. Model interpretation is performed using Partial Dependence Plots and Individual Conditional Expectation Plots. Temperature, curing regime, and amounts of aggregates are identified as the most significant predictors. Full article

Despite the advantageous benefits offered by self-compacting concrete, its uses are still limited due to the high pressure exerted on the formwork. Different parameters, such as those related to concrete mix design, the properties of newly poured concrete, and placement method, have an impact on form pressure. The question remains unanswered on the degree of the impact for each parameter. Therefore, this study aims to study the level of impact of these parameters, including slump flow, T500 time, fresh concrete density, air content, static yield stress, concrete setting time, and concrete temperature. To mimic the casting scenario, 2 m columns were cast at various casting rates and a laboratory setup was developed. A pressure system that can wirelessly and continuously record pressure was used to monitor the pressure. Each parameter’s impact on the level of pressure was examined separately. Casting rate and slump flow were shown to have a greater influence on pressure. The results also demonstrated that, while higher thixotropy causes form pressure to rapidly decrease, a high casting rate and high slump flow lead to high pressure. This study suggests that more thorough analysis should be conducted of additional factors that may have an impact, such as the placement method, which was not included in this publication. Full article

The manufacture of elements containing two types of concrete allows for the minimization of the amount of Portland cement by matching the properties of concrete with local structural and durability requirements. The most common production method of the hybrid element is wet–on–hard and wet–on–wet. Casting wet–on–dry is the most common approach while casting wet–on–wet has been used mostly for concrete overlays and screeds. The study focuses on the wet–on–wet method but is applied in the production of vertical and horizontal elements. Bond-behavior and micro properties of the wet–on–wet casting interface of ultra–high–performance concrete (UHPC)–normal strength concretes are investigated. The obtained results indicate the formation of a hybrid interfacial transition zone between the two types of casted concrete. The binder matrix located in this zone appeared to combine properties of both used concrete. Porosity, phase composition, and presumably also strength, changed gradually. Furthermore, despite significant differences in shrinkage, no microcracking or delamination was observed in that zone. The ultimate flexural and compressive strength of the produced elements were either equal to the stronger concrete or were higher than the weaker of the used concrete. Full article

The maximum amount of lateral formwork pressure exerted by self-compacting concrete is essential to design a technically correct, cost-effective, safe, and robust formwork. A common practice of designing formwork is primarily based on using the hydrostatic pressure. However, several studies have proven that the maximum pressure is lower, thus potentially enabling a reduction in the cost of formwork by, for example, optimizing the casting rate. This article reviews the current knowledge regarding formwork pressure, parameters affecting the maximum pressure, prediction models, monitoring technologies and test setups. The currently used pressure predicting models require further improvement to consider several pressures influencing parameters, including parameters related to fresh and mature material properties, mix design and casting methods. This study found that the maximum pressure is significantly affected by the concretes’ structural build-up at rest, which depends on concrete rheology, temperature, hydration rate and setting time. The review indicates a need for more in-depth studies. Full article

A reduced carbon footprint and longer service life of structures are major aspects of circular economy with respect to civil engineering. The aim of the research was to evaluate the interfacial bond properties between a deteriorated normal strength concrete structure and a thin overlay made of Eco-UHPC containing 50 wt% of limestone filler. Two types of formwork were used: untreated rough plywood and surface treated shuttering plywood. The normal strength concrete elements were surface scaled using water jets to obtain some degradation prior to casting of the UHPC overlay. Ultrasonic pulse velocity (UPV), bond test (pull-off test), and Scanning Electron Microscopy (SEM) combined with Energy Dispersive Spectrometry (EDS) were used for analysis. Elements repaired with the Eco-UHPC showed significantly improved mechanical properties compared to the non-deteriorated NSC sample which was used as a reference. The bond strength varied between 2 and 2.7 MPa regardless of the used formwork. The interfacial transition zone was very narrow with only slightly increased porosity. The untreated plywood, having a rough and water-absorbing surface, created a surface friction-based restraint which limited microcracking due to autogenous shrinkage. Shuttering plywood with a smooth surface enabled the development of higher tensile stress on the UHPC surface, which led to a more intensive autogenous shrinkage cracking. None of the formed microcracks penetrated through the entire thickness of the overlay and some were partly self-healed when a simple water treatment was applied. The project results showed that application of UHPC as repair material for concrete structures could elongate the lifespan and thus enhance the sustainability. Full article

Most of the currently used concretes are based on ordinary Portland cement (OPC) which results in a high carbon dioxide footprint and thus has a negative environmental impact. Replacing OPCs, partially or fully by ecological binders, i.e., supplementary cementitious materials (SCMs) or alternative binders, aims to decrease the carbon dioxide footprint. Both solutions introduced a number of technological problems, including their performance, when exposed to low, subfreezing temperatures during casting operations and the hardening stage. This review indicates that the present knowledge enables the production of OPC-based concretes at temperatures as low as −10 °C, without the need of any additional measures such as, e.g., heating. Conversely, composite cements containing SCMs or alkali-activated binders (AACs) showed mixed performances, ranging from inferior to superior in comparison with OPC. Most concretes based on composite cements require pre/post heat curing or only a short exposure to sub-zero temperatures. At the same time, certain alkali-activated systems performed very well even at −20 °C without the need for additional curing. Chemical admixtures developed for OPC do not always perform well in other binder systems. This review showed that there is only a limited knowledge on how chemical admixtures work in ecological concretes at low temperatures and how to accelerate the hydration rate of composite cements containing high amounts of SCMs or AACs, when these are cured at subfreezing temperatures. Full article

An efficient solution to increase the sustainability of building materials is to replace Portland cement with alkali-activated materials (AAM). Precursors for those systems are often based on water-cooled ground granulated blast furnace slags (GGBFS). Quenching of blast furnace slag can be done also by air but in that case, the final product is crystalline and with a very low reactivity. The present study aimed to evaluate the cementitious properties of a mechanically activated (MCA) air-cooled blast furnace slag (ACBFS) used as a precursor in sodium silicate alkali-activated systems. The unreactive ACBFS was processed in a planetary ball mill and its cementing performances were compared with an alkali-activated water-cooled GGBFS. Mixes based on mechanically activated ACBFS reached the 7-days compressive strength of 35 MPa and the 28-days compressive strength 45 MPa. The GGBFS-based samples showed generally higher compressive strength values. Full article

Exposure conditions are critical for the autogenous self-healing process of Portland cement based binder matrixes. However, there is still a significant lack of fundamental knowledge related to this factor. The aim of this paper was to investigate and understand the effects of various potentially applicable curing solutions on the efficiency of the crack closure occurring both superficially and internally. Four groups of exposures were tested, including exposure with different water immersion regimes, variable temperatures, application of chemical admixtures, and use of solutions containing micro particles. The self-healing process was evaluated externally, at the surface of the crack, and internally, at different crack depths with the use of optical and scanning electron microscopes (SEM). The phase identification was done with an energy dispersive spectrometer combined with the SEM. The results showed very limited self-healing in all pure water-based exposures, despite the application of different cycles, temperatures, and water volumes. The addition of a phosphate-based retarding admixture demonstrated the highest crack closure, both internally and externally. The highest strength recovery and a very good crack closure ratio was achieved in water exposure containing micro silica particles. The main phase observed on the surface was calcium carbonate, and internally, calcium silicate hydrate, calcium carbonate, and calcium phosphate compounds. Phosphate ions were found to contribute to the filling of the crack, most likely by preventing the formation of a dense shell composed of hydration phases on the exposed areas by crack unhydrated cement grains as well as by the additional precipitation of calcium and phosphate-based compounds. The micro sized silica particles presumably served as nucleation sites for the self-healing products growth. Changes in the chemical composition of the self-healing material were observed with a distance from the surface of the specimen. Full article