Alloys, Volume 3, Issue 3 (September 2024) – 4 articles

Abstract: The refractory complex concentrated alloy (RCCA) 5Al–5Cr–5Ge–1Hf–6Mo–33Nb–19Si–20Ti–5Sn–1W (at.%) was studied in the as-cast and heat-treated conditions. The partitioning of solutes in the as-cast and heat-treated microstructures and relationships between solutes, between solutes and the parameters VEC and Δχ, and between these parameters, most of which are reported for the first time for metallic UHTMs, were shown to be important for the properties of the stable phases A15–Nb₃X and the D8_m βNb₅Si₃. The nano-hardness and Young’s modulus of the A15–Nb₃X and the D8_m βNb₅Si₃ of the heat-treated alloy were measured using nanoindentation and changes in these properties per solute addition were discussed. The aforementioned relationships, the VEC versus Δχ maps and the VEC, Δχ, time, or VEC, Δχ, Young’s modulus or VEC, Δχ, nano-hardness diagrams of the phases in the as-cast and heat-treated alloy, and the properties of the two phases demonstrated the importance of synergy and entanglement of solutes, parameters and phases in the microstructure and properties of the RCCA. The significance of the new data and the synergy and entanglement of solutes and phases for the design of metallic ultra-high temperature materials were discussed. Full article

Light alloys based on magnesium are widely used in most areas of science and technology. However, magnesium powder alloys are quite difficult to sinter due to the stable film of oxides that counteracts diffusion. Therefore, finding a method to activate magnesium sintering is urgent. This study examines the effect of adding 5 wt. % and 10 wt. % zinc to the sintering pattern of magnesium powders at 430 °C; a dwell of 30 min was used to homogenize at the densification’s temperature. Scanning electron microscopy (SEM) was used to characterize the alloy’s microstructure, while the phase composition was characterized using X-ray diffraction (XRD) and energy dispersion spectroscopy (EDS). The sintering densities of Mg–5Zn and Mg–10Zn were found to be 88% and 92%, respectively. The results show that after sintering, a heterophase structure of the alloy is formed based on a solid solution and phases MgZn and Mg₅₀Zn₂₁. To establish the sintering mechanism, the interaction at the MgO and Zn melt phase interface was analyzed using the sessile drop method. The minimum contact angle—65°—was discovered at 500 °C with a 20 min holding time. It was demonstrated that the sintering process in the Mg–Zn system proceeds through the following stages: (1) penetration of zinc into oxide-free surfaces; (2) crystallization of a solid solution, intermetallics; and (3) the removal of magnesium oxide from the particle surface, with oxide particles deposited on the surface of the sample. Full article

An innovative technology for the direct reduction of copper slag was studied while smelting Cu-Fe alloy by carbon to recover the main valuable elements from the copper smelting slag. The melting temperature of samples first decreased, followed by an increase in Fe₃O₄ content in slag. The melting temperature reached the minimum temperature of 1157 °C once the Fe₃O₄ content was about 8 wt%. The recovery rate of copper and iron first increased gradually, followed by a rapid increase in the modifier (CaO). Subsequently, the rise in the recovery rate slowed down. The reduction rate of copper and iron only increased by 1.61% and 1.05% from 5 wt% CaO to 10 wt% CaO, but significantly increased by 8.89% and 14.21% from 10 wt% CaO to 25 wt% CaO, and remained almost unchanged beyond 25 wt% CaO. This could be attributed to the reaction between modifier (CaO) and silicate in acidic copper slag to generate low melting point composite oxide while replacing free iron oxides, improving the melting properties and reduction reaction. Meanwhile, the recovery rates of copper and iron increased with the increase of reaction time, reaction temperature, and reduction agent in a certain range. To obtain good element yield, the optimum conditions for reducing copper and iron from the molten copper slag were determined to be 1500 °C, 14 wt% C, 20–25 wt% CaO, and 60–80 min. The recovery rates of iron and copper reached about 90% and 85%, and the contents of iron and copper in alloy reached about 91–93 wt% and 5–7 wt%, respectively. The tailing was mainly composed of Ca₃Si₃O₉, Ca(Mg,Al)(Si,Al)₂O₆, and SiO₂, which could be used as a raw material for cement and pelletizing. Full article