1. Introduction
The major factors subject to the efficiency of the heat transfer processes include structure, control, and analysis of thermal systems. Evidently, fluids dominantly grow the flow and rate of heat transfer corresponding to the applications in engineering and scientific systems including efficient heat surface area, microscale cooling devices, vibration of heated surfaces, and microelectronic devices etc. In order to get more efficient results, there have been a lot of attempts by researchers to synthesize these fluids for an amplified heat transfer rate, using the composition of several fluids as well as the dispersion of metallic particles of different sizes and shapes etc. The efficient thermal characteristics of nanofluids, colloidal suspensions of nanoparticles in base fluids primarily prepared by Choi [
1], were guaranteed due to their substantially modified thermal conductivities with insignificant abrasion. Since then, investigators have conducted various theoretical and experimental studies, and some are mentioned here [
2,
3,
4,
5,
6,
7,
8]. In order to acquire the highest composite thermal features, hybrid nanofluids are synthesized by imbedding the nanoparticles of several materials into conventional fluids that possess improved physical and chemical properties in a homogeneous phase. In this regime, Iqbal et al. [
9] demonstrated the thermal characteristics of the MHD (Cu–CuO/water) hybrid nanofluid in rotating flow through an oscillatory vertical conduit by considering the influences of Hall current and thermal radiation. Awais et al. [
10] examined the peristaltic transport of rheological hybrid nanofluid for the power-law model due to cilia motion, and encountered the impact of magnetic induction as well. They illustrated that nanoparticles’ coating perks up peristaltic pumping and heat transfer properties, which are important to use in endoscopy and cancer therapy. Ali et al. [
11] explored MHD peristalsis of the TiO
2–Cu/H
2O hybrid nanofluid by taking the non-Newtonian Jeffrey model with wall slip conditions. Recently, Abbas et al. [
12] studied an extension of the rheological hybrid nanofluid models, named as the Yamada–Ota and Xue models, for flow over a moving needle. Parveen et al. [
13] utilized computational intelligence techniques in order to estimate the pressure rise and rate of heat transfer in the dynamics of the hybrid nanofluid under magnetic induction effects in endoscopy. It was revealed that heat transfer coefficient enhancements towards the Br and χ. neural network algorithm were employed in order to validate the experimental data, and very accurate results were obtained. Lund et al. [
14] established a study for finding multiple solutions for MHD (Cu–Fe
3O
4/H
2O) hybrid nanofluid dynamics, which occurred due to a variable stretching/shrinking surface. The research community have been using hybrid nanomaterials in diverse applications with the aim to get efficient thermal systems with little nanoparticles’ volume fraction at a minor cost of production, and some of this literature is presented in [
15,
16,
17]. Further, metal oxides show excellent chemical inertness and they are stable. Alumina (Al
2O
3) is preferred to study here, owing to its validity in the improvement of ceramic density, smoothness, fracture toughness, in refractory products and as an ideal material of far-infrared emission. Its potential applications are attributed to its abrasiveness, enhanced hardness, chemical inertness, stability, strong emission, absorbance spectra and high properties of electrical and thermal insulation. However, Al
2O
3 possesses small fracture resistance and is flammable, so its use as a structural material is hindered. While metallic nanoparticles possess unique optoelectrical properties, are inflammable as well as high thermal and electrical conductivities [
18,
19,
20]. Therefore, Al
2O
3–Ag/H
2O is studied in present work.
Boundary-layer flows combined with heat transfer and followed by a stretching sheet, as primarily proposed by Sakiadis [
21], has become a field of curiosity for scientists and researchers owing to its incredible technological and industrial utilizations, including the manufacturing of materials by extrusion procedures and heat tampered materials flowing inside a wind-up roll possessing the features of moving continuous sheets. Moreover, viscous dissipation effects are dominant in strong gravitational fields. Viscous dissipation and heat generation in mixed convective boundary-layer flow play a vital role in different fields such as chemical, mechanical, and aerospace engineering. Karwe and Jaluria [
22] analyzed fluid transport with mixed convection over a moving plate in procedures like rolling and extrusion. Awais et al. [
23] inspected the effects of heat generation/absorption in a boundary-layer flow of Maxwell nanofluid by adopting numerical and analytical techniques. Wang et al. [
24] studied the effects of radiative heat flux with heat generation/absorption in homogeneous–heterogeneous catalytic reactions of Oldroyd-B fluid. Sharma et al. [
25] numerically analyzed fractional boundary-layer flow due to a stretching sheet of non-uniform thickness with the help of a finite-difference approach. Khan et al. [
26] explored heat and mass transfer analysis in three-dimensional nanofluids flowing on a linear stretching sheet under convective wall conditions. Further, magnetic field effects in boundary-layer flow, with heat transport of electrically conducting fluids, have plausible applications in several industrial contexts involving the continual stretching of artificial fibers, plastic films, and the spinning of metals etc. The study of interactions between electrically conducting fluids and a magnetic field was named magnetohydrodynamics (MHD) by Alfven [
27]. Physically, external magnetic fields generate an electric current in a flowing electrically conducting fluid, which polarizes the fluid due to the changing magnetic flux. Awais et al. [
28] carried out heat and mass transfer analysis for Casson fluid flow through a porous medium on a shrinking wall associated with the effects of heat source/sink and Lorentz force. Irfan et al. [
29] introduced a new computational technique designed for EMHD nanofluid dynamics over a non-uniform surface with variable liquid characteristics. Awais et al. [
30] scrutinized the influence of temperature-dependent transport properties on the rate of heat and mass transfer in MHD bioconvection nanofluid rheology suspended by gyrotactic microorganisms using a numerical technique. Magnetic induction effects are negligible in the case of large magnetic diffusion. However, the phenomenon is significant with the dynamical conductive fluid, which advects the flux lines of the magnetic field so the magnetic Reynolds number becomes countable. The induction of MHD is imperative to amplify the flow fields in a preferable direction by changing the boundary-layer structure. In order to understand the flow mechanism under magnetic induction effects, several attempts have been made [
31,
32,
33,
34,
35].
In thermodynamical investigations of flow and heat transfer processes, including complicated physiological structures, spin moment, and inertial displacement of particles, a major issue is to improve the efficiency of thermal systems to reduce heat loss, which is a quantitative measure called entropy generation. Khan et al. [
36] investigated the significance of Al
2O
3–H
2O and γ-Al
2O
3–C
2H
6O
2 nanomaterials in Darcy-Forchheimer stagnation point flow with entropy optimization. Mumraiz et al. [
37] established the analysis of entropy generation in the transport of electrical MHD (Al
2O
3–Cu/H
2O) hybrid nanofluid in the presence of variable heat flux. Ali et al. [
38] studied entropy optimization in the MHD peristaltic transport of Cu–water nanofluid under the effects of wall slip conditions. Awan et al. [
39] numerically analyzed entropy optimization and magnetic induction effects on the ciliary-induced peristaltic transport of hybrid nanomaterials. It was ensured that the thermal performance of the fluid could be boosted by utilizing the hybrid nanomaterial strength of the wall for stability. The irreversibility analysis ensures that entropy is reduced for a strong magnetic field. Sahoo et al. [
40] carried out the analysis of entropy optimization, with dissipative heat transfer, in mixed convective MHD Casson nanofluid flow under the effects of Hall current and thermal radiation.
In view of the above-mentioned literature, the boundary-layer flow of hybrid nanofluid influenced by an induced magnetic field over a stretching sheet for entropy generation and heat transfer analysis under the effects of mixed convection, heat generation, and viscous dissipation, has not yet been investigated. The present study is an extension of the work of Iqbal et al. [
41]. Furthermore, this study is concerned with analytical solutions using the homotopy analysis method (HAM) as well. The behavior of the flow profiles and entropy generation number against the involved parameters is exposed graphically, and the results for skin friction and Nusselt number have been computed and demonstrated.
2. Problem Development
Consider the mixed convection boundary-layer flow of Newtonian (Al
2O
3–Ag/H
2O) hybrid nanofluid over an impermeable linearly stretchable sheet. The sheet velocity is
and the ambient velocity of the fluid is
, in which
a and
c denote positive constants. The temperature of the sheet and free stream are represented as
, accordingly. Furthermore, the influence of magnetic induction is encountered where the magnetic field at free stream is denoted as
. The geometrical interpretation of this circumstance is given in
Figure 1.
The vector form of the governing model is given here. The continuity equations for velocity and magnetic induction are as follows:
The equation for the conservation of momentum and induced magnetic field are as follows:
The equation for the conservation of energy is as follows:
In the above model,
V,
H and T express the variables of the velocity field, induced magnetic field and temperature, while
I represents the identity matrix, and
p is the fluid pressure. Moreover,
,
,
Q, and
g denote the magnetic permeability, magnetic diffusivity, heat generation/absorption parameter, and gravitational acceleration. The expressions for the Cauchy stress tensor
and viscous dissipation function
for the Newtonian fluid are as follows:
In component form, the following applies:
The associated boundary conditions are as follows:
where
and
denote the
x and
y components of
V and
H, respectively. Further, the parameters involved are as follows:
For the (Al2O3–Ag/H2O) hybrid nanofluid are volume fractions, stand for the density, thermal expansion coefficient, specific heat at constant pressure and thermal conductivity, with the subscripts denoting properties of the fluid, nanofluid, hybrid nanofluid, solid nanoparticle of silver and alumina with s as the shape factor, respectively.
Invoking the following quantities for transformation of the partial differential equations with the similarity variable
, we obtain the following:
We get the transformed set of differential equations as the following:
The transformed wall properties are as follows:
where the Prandtl number
Pr, stretching ratio parameter
, reciprocal of magnetic Prandtl number
, magnetic parameter
, Eckert number
Ec, heat generation/absorption parameter
and mixed convection parameter
are expressed as the following:
The considerable physical quantities are the coefficient of skin friction
and Nusselt number
, which are expressed as the following:
In the above expressions,
gives shear stress at the wall while
denotes wall heat flux. The non-dimensional form with the help of similarity transformation is as follows:
where
represents the local Reynolds number.
Entropy Analysis
The volumetric entropy generation rate (
) for the fluid, influenced by the induced magnetic field, can be expressed as follows:
where the terms on the right-hand side depict the entropy generation caused by heat transfer across the boundary layer, viscous dissipation and induced magnetic field, respectively. The characteristic entropy generation rate with the characteristic length
L is as follows:
Hence, the dimensionless entropy generation rate by using Equation (18) and the similarity transformation in Equation (17) is as follows:
In which, is Reynolds number, and expresses temperature ratio parameter.
4. Results and Discussion
In this section, the influences of important parameters on the flow variables and entropy generation number are exposed and discussed.
Figure 2,
Figure 3 and
Figure 4 plot the variation in velocity (
) against the mixed convection parameter, Brinkman number and heat generation parameter.
Figure 2 gives an increment in
for an increasing magnitude of
. This behavior occurred due to a large temperature gradient which led to high buoyancy effects and directly affected the convection in fluid. In fact, buoyancy force behaves as a favorable pressure gradient which drives the fluid, so the velocity and the boundary-layer thickness become larger. The dominant effect appears in the region near the sheet, which approaches the value of the velocity ratio at a distance far from the sheet. Here, negative and positive values of
indicate the cooling and heating phenomenon of the fluid, respectively. According to the graph, a strong cooling effect corresponds to a decrease in the velocity, while a heating effect accelerates the flow.
Figure 3 demonstrates an increment in
for
. The negative values of
depict the heat absorption phenomenon, whereas the positive values correspond to heat generation. The graphical behavior shows that strong absorption effects at large negative values tend to decrease the fluid velocity, while increasing positive values regarding heat generation increase the velocity and thickness of its boundary layer. This is because, by definition of
, the internal heat of fluid rises for a higher magnitude which directly enhances kinetic energy and thus fluid flow.
Figure 4 plots
against
Br at
Pr = 6.2. The increase in velocity boundary-layer thickness in the graph is because of the fact that large values of
Br, by definition, lead to a high velocity of the stretching sheet. According to the no-slip wall condition, fluid velocity increases near the sheet but the effect is not very dominant due to viscous forces. These effects disappear in free stream where the flow is only affected due to the mixed convection and magnetic induction.
Figure 5 explores the dual behavior of
against
. This graph presents a dominant increasing trend in
, which gradually frails up to the inflation point where the parameter has no effect. This trend is due to the addition of a flow mechanism near the sheet. In the free-stream region,
decreases and goes asymptotically to 1 as the values of
rise. Similar behavior is noticed for both the assisting as well as opposing case.
The physical influence of dimensionless parameters on the temperature of the fluid is plotted in
Figure 6 and
Figure 7. The variation in the temperature field towards the growing values of
is illustrated in
Figure 6 which explores the decay in temperature. Physically, increasing the magnitude of
corresponds to an increase in the temperature gradient and accelerates the flow due to gravity. These combined effects increase fluid velocity, and heat transfer rate increases which decreases the internal energy of the fluid. Moreover, high negative values of
possess a higher ambient temperature, and the fluid temperature is high. The temperature profile for variation in
is depicted in
Figure 7. With an increase in the negative values from −0.2 to −0.4, the temperature of the fluid decreases absolutely due to high heat absorption. Contrary to this, an increase in the positive values show strong heat generation which enhances the fluid temperature as well as the thermal boundary-layer thickness according to the definition of heat generation.
The variation in the entropy generation number (
Ns) for the physical parameters is displayed graphically to understand the physical aspects of the work. The graph of
Ns for increasing values of
is presented in
Figure 8, which shows an increase in entropy generation. Since entropy is directly affected by temperature gradient, which raises the flow and heat transfer rate, the results lead to a rise in entropy generation.
Figure 9 depicts the variation in
Ns against values of the Brinkman number which indicates an increase in
Ns. The reason behind such behavior is that rising values of
Br explore viscous effects in fluid due to the no-slip wall condition. This trend causes flow acceleration and an increase in entropy.
The influence of temperature ratio parameter on
Ns is explored in
Figure 10. It presents that increasing values of
yield high entropy due to the rising temperature gradient of the fluid. An enhancement in heat generation results in the rising of the internal energy and temperature of the fluid, and a decrease in kinetic energy which reduces heat transfer. Therefore, entropy in the system reduces. This fact is depicted in
Figure 11. It is noticed from the graph of the entropy generation number, that the effect of involving the parameters and magnitudes of the entropy generation number is considerably close to the stretching sheet and less far from it. This trend is physically due to the strong viscous effects and temperature gradient near the wall.
Table 2 represents the numerical values of the thermophysical quantities for the considered hybrid nanofluid. Moreover,
Figure 12,
Figure 13,
Figure 14 and
Figure 15 explore the bar-chart view of skin friction and Nusselt number against pertinent parameters. The influence of different nanoparticle shape factors, including bricks (
s = 3.7), cylinders (
s = 4.9) and platelets (
s = 5.7), are investigated for heat transfer analysis. These numerical values are presented in
Table 3 and
Table 4 as well.
Figure 12 reveals that C
f decreases for the opposing flow, corresponding to the negative values of
when they change from −1 to −4. The opposite trend is explored for the positive values of
Moreover, the effects of the magnetic parameter on
show a decreasing behavior. The magnetic parameter gives the order of the ratio of magnetic energy and kinetic energy per unit volume, and with an increase in magnitude, flow rate decreases. An increase in temperature difference occurs for enhancing values of
, which decreases shear effects. Also, a comparison of the Nusselt number with expansion in the shape factor of nanoparticles is presented, which illustrates that platelet-shaped nanoparticles have more contribution in enhancing thermal characteristics as compared to the others.
Besides this, the results of the HAM solutions in the present study are compared with the numerical results presented in the work of Iqbal et al. [
41]. The extended parameters are neglected i.e.,
in order to gain the model presented in Iqbal et al. [
41]. The results of both studies are shown in
Table 5 and
Table 6. It is observed that the existing results are in good agreement with the previously published results.