Next Article in Journal
Stearic Acid Coated MgO Nanoplate Arrays as Effective Hydrophobic Films for Improving Corrosion Resistance of Mg-Based Metallic Glasses
Next Article in Special Issue
Surface Study of CuO Nanopetals by Advanced Nanocharacterization Techniques with Enhanced Optical and Catalytic Properties
Previous Article in Journal
Using Dual Microresonant Cavity and Plasmonic Effects to Enhance the Photovoltaic Efficiency of Flexible Polymer Solar Cells
Previous Article in Special Issue
Dopant-Free Triazatruxene-Based Hole Transporting Materials with Three Different End-Capped Acceptor Units for Perovskite Solar Cells
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Study on the Effects of a π Electron Conjugated Structure in Binuclear Metallophthalocyanines Graphene-Based Oxygen Reduction Reaction Catalysts

1
School of Materials Science and Chemical Engineering, Xi’an Technological University, Xi’an 710021, China
2
Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of Education, College of Chemistry & Material Chemistry, Northwest University, Xi’an 710069, China
*
Authors to whom correspondence should be addressed.
Nanomaterials 2020, 10(5), 946; https://doi.org/10.3390/nano10050946
Submission received: 3 April 2020 / Revised: 2 May 2020 / Accepted: 9 May 2020 / Published: 15 May 2020
(This article belongs to the Special Issue Novel Nanomaterials for Applications in Energy and Catalysis)

Abstract

:
The high overpotentials for oxygen reduction reaction (ORR) create an extremely negative impact on the energy efficiency of the air-based battery systems. To overcome this problem, binuclear ball-type metallophthalocyanines containing methoxy substituents (M2Pc2(EP)4, M = Fe(II), Co(II) and Zn(II)) were wrapped with polystyrene sodium sulfonate (PSS) modified graphene oxide (GO), using a facilely “solvothermal π-π assembly” method to prepare M2Pc2(EP)4/PSS-Gr composites. Compared with the commercial Pt/C catalysts, the M2Pc2(EP)4/PSS-Gr composites enhanced the catalytic activity of oxygen reduction reaction. The π electron conjugated structure of the MN4-type phthalocyanine macrocyclic system strongly influenced the one-step four-electron electrocatalytic process of the M2Pc2(EP)4/PSS-Gr composites. Moreover, the π-π interactions between the M2Pc2(EP)4 and PSS-Gr dramatically enhanced the π electron density in the conjugated structure and oxygen could be reduced more easily. The electrocatalytic activity test was displayed in the order of Fe2Pc2(FP)4/PSS-Gr > Co2Pc2(EP)4/PSS-Gr > Zn2Pc2(EP)4/PSS-Gr. The results indicated that the catalytic performance of M2Pc2Rn could be enhanced by the modification of π electron conjugated structure of M2Pc2(EP)4 and carbon materials.

Graphical Abstract

1. Introduction

With the exhausting of traditional energy sources and increasing concerns of environmental pollution, it is urgent to explore and utilize clean energy. Fuel cells have become the research hotspots for new energy development because of their low cost, simple structure, special energy density and other merits [1,2,3]. Nevertheless, the high overpotentials for the oxygen reduction reactions create an extremely negative impact on the energy efficiency of air-based battery systems [4]. Although Pt and its alloys contribute significantly in decreasing the overpotential of oxygen reduction reaction (ORR) because of their high catalytic activity, they are limited in the scarcity of reserves, high price and lack of excellent methanol resistance [5]. To overcome this problem, extensive efforts have been implemented to study low-cost, non-precious metal substitute catalysts for Pt/C catalysts [6,7]. Specially, many reports have pointed out that the ability to carry oxygen molecules plays a key role in the ORR process [8,9]. Among the large variety of metal macrocycles, metal-N4-chelates, like metalloporphyrin (MPs) and metallophthalocyanine (MPcs), which have an 18 π electrons conjugated structure, have the biomimetic oxygen carrier functions similar to the naturally occurring hemeproteins [10]. Due to the delocalization effect and weakly bonding character of π electron clouds in a conjugated structure, the metal-N4-chelates with π electron conjugated structure could be oxidized and reduced much more easily, establishing them as a promising precursor for preparing ORR catalysts [11,12,13]. Compared with MPs, the periphery of the benzene ring of phthalocyanines can be modified with a variety of substituents, giving MPcs a variety of chemical structures and properties [14,15,16]. The chemical natures of the ligand and the central ion strongly influence the catalytic properties of the metal-N4-chelates macrocycles. In the ORR process, O2 is coordinated to the M of MPcs and the electrons then migrate from the MPcs to O2 to form adduct MPc-O2 [17,18]. Considering a high π electron density of the conjugated structure, metallophthalocyanines have an excellent catalytic activity for oxygen reduction reaction [19,20,21].
In recent years, a new class of ball-type M2Pc2 compounds containing two metal centrals has drawn much attention because of its attractive structure [22,23]. Both the face-to-face monomer distance and the d filling of the metal central ions can significantly affect the ball-type Pcs’ physical and chemical behavior [24,25]. For the M2Pc2 with a strong ligand-field effects of MN4-chelates, the catalytic activity is mainly affected by the chemical structure of the phthalocyanines, the radius and the d-filling of the metal central ions [26]. In addition, the presence of bridging units including electronegative groups highly enhanced catalytic activity of the phthalocyanines. The multiple electron-withdrawing substituents on the periphery of metal Pcs increased their catalytic activity [25]. The results pointed out that the possibility of the increase of the catalytic performance by the modification of the main M2Pc2 skeleton, and encouraged us to design phthalocyanine compound containing methoxy substituents. Furthermore, reports have also pointed out that MPc loaded on carbon materials is conducive to enhance the catalytic activity for the oxygen reduction reaction [27,28]. Graphene oxide has a high conductivity, excellent electron mobility and relatively high theoretical specific surface areas, establishing itself as a good candidate to provide a pathway for fast electron transferring and to prevent the aggregation of MPcs nanoparticles [29,30]. It has demonstrated that the catalytic activity of the π electron conjugated structure towards oxygen reduction reaction are related to the strong π-π supramolecular interaction between MPc compounds and graphene, which promote electron transfer between them leading to an apparent improvement for the oxidative reactions [31,32,33,34]. However, pristine GO possesses few proton-conducting groups, which negatively enhances the conductivity of GO. Therefore, grafting GO with a sulfonated group (-SO3H; PSS-Gr) using various methods has been studied, as this strategy not only improved the conductivity of the GO, but also enabled the better dispersibility of GO [35].
Some studies have provided valuable mechanistic insights for the formation of M2PcRn-O2 intermediates. However, the study on the effects of the π electron conjugated structure and the π-π interactions between the M2Pc2(EP)4 and PSS-Gr generally restrict the design of the M2Pc2Rn-based catalysts. In this work, composites of binuclear ball-type metallophthalocyanines with methoxy substituents (M2Pc2(EP)4, M = Fe(II), Co(II) and Zn(II)) were loaded on the surface of PSS-Graphene (PSS-Gr), to enhance the catalytic activity and stability for ORR based on the π electron conjugated structure of the MN4-type phthalocyanine macrocyclic system, and the π-π supramolecular interaction between MPc nanoparticles and graphene.

2. Experimental

2.1. Materials

4, 4-bis (4-hydroxyphenyl) pentanoic acid (98%) and 4-nitrophthalonitrile (99%) were purchased from Aladdin (Shanghai, China). The other chemicals were of analytical grade and were used without further purification. The target M2Pc2(EP)4 compounds were prepared by taking bisphthalonitrile and the corresponding metal salts (M = Fe(II), Co(II), and Zn(II)) as the raw materials in the dimethylaminoethanol (DMAE). This was done according to the literature [25].
Preperation of M2(II)Pc2(EP)4: Bisphthalonitrile (0.56 g, 1.02 mmol), Zn(OAc)2 2H2O (0.112 g, 0.52 mmol) and 4 mL DMAE were poured into a Teflon-lined autoclave at 220 °C for 4 h (Figure 1). The reaction mixture was then poured into methanol to produce a precipitate, and the precipitate was washed sequentially with acetic acid, water and methanol. The crude product was then dissolved in DMF and reprecipitated by gradually adding methanol to the solution. The precipitate was washed again as in the previous method followed by centrifugation and dried at 100 °C in an oven.
[2′,10′,16′,24′-{Tetrakis-4,4′-bis (4- (3-cyano-4-isocyanophenoxy) phenyl) pentanoate diphthalocyaninato) dizinc (II)]: Zn2(II)Pc2(EP)4 (0.3815 g, yield 64.21%), green solid, m.p. > 300 °C. IR (KBr) νmax/cm−1: 1715 (νC = o); 1381 (νC = C); 892 (νM-N); 2972, 1009 (νC-H(Pc)), 1229 (νAr-O-Ar), 740 (νPc). UV-Vis (DMF) λmax/nm: B band: 267, 354; Q band: 612, 677. Anal. Cald. for C32H16N8Zn: C, 69.78; H, 4.10; N, 9.58; Found: C, 69.21; H, 4.54; N, 9.29.
[2′,10′,16′,24′-{Tetrakis-4, 4′-bis (4- (3-cyano-4-isocyanophenoxy) phenyl) pentanoate diphthalocyaninato) diiron (II)]: Fe2(II)Pc2(EP)4 (0.2120 g, yield 36.64%), olive green solid, m.p. > 300 °C. IR (KBr) νmax/cm−1: 1713 (νC = o); 1401 (νC = C); 874 (νM-N); 2970, 1011 (νC-H(Pc)), 1234 (νAr-O-Ar), 752 (νPc). UV-Vis (DMF) λmax/nm: B band: 267, 323; Q band: 621, 668. Anal. Cald. for C32H16N8Fe: C, 70.07; H, 4.12; N, 9.62; Found: C, 69.68; H, 3.63; N, 9.27.
[2′,10′,16′,24′-{Tetrakis-4, 4′-bis (4- (3-cyano-4-isocyanophenoxy) phenyl) pentanoate diphthalocyaninato) dicobalt (II]: Co2(II)Pc2(EP)4(0.3021 g, yield 51.52%), dark blue solid, m.p. > 300 °C. IR (KBr) νmax/cm−1: 1707 (νC = o); 1387 (νC = C); 891 (νM-N); 2970, 1011 (νC-H(Pc)), 1231 (νAr-O-Ar), 745 (νPc). UV-Vis (DMF) λmax/nm: B band: 268, 362; Q band: 668. Anal. Cald. for C32H16N8Co: C, 69.97; H, 4.11; N, 9.61; Found: C, 69.55; H, 4.56; N, 9.19.

2.2. Characterization

Transmission electron microscopy (TEM) analysis was performed on a JEOL JEM-2010 electron microscope at 200 kV. The system consists of a vertical SEM column that was situated at 36° relative to the FIB column, operating at 3 kV to optimize surface sensitivity. The IR spectra were recorded on a Germany Bruker Vertex70 spectrometer (Bruker, Karlsruhe, Germany). The UV-vis absorbance was recorded on a UV/visible spectrophotometer (UV-1600, Shanghai, China) using a quartz cell with a path length of 10 mm at room temperature. X-ray photoelectron spectroscopy (XPS) was measured using an Axis Ultra spectrometer with an Al (Mono) Kα X-ray source (1486.6 eV). The binding energies (BE) were normalized to the signal for adventitious carbon at 284.8 eV. The electrocatalytic performance was evaluated by an electrochemical workstation CHI 660E (Shanghai CHENHUA Company, Shanghai, China) and a Pine Instrument Company AF-MSRCE modulator rate rotator (Grove, PA, USA) in a 0.1 M KOH solution, separately.

2.3. Synthesis

2.3.1. Polystyrene Sodium Sulfonate Modified Graphene (PSS-Gr) Preparation

Graphene oxide (GO), obtained from Aladain Co. Ltd. (Shanghai, China) was dispersed in 100 mL distilled water with an ultrasonic technique, followed by the addition of 1 g of sodium polystyrene sulfonate at room temperature, and stirred for 12 h. Then, 2 mL of hydrazine hydrate was then added. The crude products were washed with deionized water, ethanol and n-pentanol, followed by centrifugation and then drying at 100 °C.

2.3.2. Preparation of Fe2Pc2(EP)4/PSS-Gr

The Fe2Pc2(EP)4/PSS-Gr composites were synthesized by a facile “solvothermal π-π assembly” method, using PSS-Gr and Fe2Pc2(EP)4 as the precursors (Figure 1). In brief, 0.1503 g of PSS-Gr powder was dispersed in 10 mL of DMF solution with an ultrasonic technique for 10 min, followed by the addition of 0.1100 g metallophthalocyanine Fe2Pc2(EP)4. The resulting solution was ultrasonically dispersed for 2 h. Nitrogen gas was then bubbled into the mixture to remove oxygen and was then poured into a Teflon-lined autoclave at 160 °C for 24 h. All of the crude products were washed with DMF, deionized water, ethanol and n-pentanol, followed by centrifugation and drying at 100 °C in an oven.
The Co2Pc2(EP)4/PSS-Gr and Zn2Pc2(EP)4/PSS-Gr composites were prepared under the same conditions.

2.4. Evaluation of the Electrocatalytic Activity

The electrocatalytic performance of M2Pc2(EP)4/PSS-Gr composites for the oxygen reduction reaction was measured by cyclic voltammetry (CV) and rotating disk electrode (RDE) techniques in a 0.1 M NaOH solution at room temperature. Specifically, the modified glassy carbon electrode is used as a working electrode. The reference electrode is saturated calomel electrode (SCE) and the platinum (Pt) wire electrode is used as counter electrode, respectively. The cyclic voltammetry tests were investigated in an O2-saturated 0.1 M NaOH solution with the scan rate of 100mV s−1. The rotating disk electrode (RDE) test was measured with a glassy carbon electrode (5 mm diameter) in O2-saturated 0.1 M NaOH solution under quasistationary conditions (5 mV·s−1 sweep rate) at 25 °C. The rotating disk electrode (RDE) was performed on a CHI 660E electrochemical workstation with an AF-MSRCE modulator rate rotator (Pine Instrument Company) using a standard three-electrode system. A platinum ring electrode and glassy carbon disk (5.61 mm diameter) was selected as the working electrode. The collection efficiency of the platinum ring was 37%.

3. Results and Discussion

3.1. Morphology and Structure of M2Pc2(EP)4/PSS-Gr Composites

The surface morphology of the M2Pc2(EP)4/PSS-Gr composites was studied by SEM and TEM images. As illustrated in Figure 2, a wrinkled paper-like feature was observed for the PSS-Gr, indicating a typical feature of the graphene sheet. In contrast to the TEM micrograph of PSS-Gr that appears transparent (Figure 2b), numerous dark particles of M2Pc2(EP)4, as indicated by the white arrow, were observed on the PSS-Gr layer from the TEM image of the M2Pc2(EP)4/PSS-Gr composites. It can be seen that M2Pc2(EP)4 nanoparticles were dispersed uniformly on the PSS-Gr surface.
The UV-Vis spectra of the Fe2Pc2(EP)4/PSS-Gr composites is shown in Figure 3. The “Q-band” of Fe2Pc2(EP)4 appeared at around 668 nm, because of the π-π originating from the HOMO (a1u and a2u) to the LUMO orbitals (eg) [25]. The absorption at 621 nm is attributed to the dimmers of Fe2Pc2(EP)4. The spectrum of the PSS-Gr did not exhibit any obvious absorption peaks from 300 to 900 nm, while that of the Fe2Pc2(EP)4/PSS-Gr composites in DMF showed an absorption peak at 741 nm. Compared with the Fe2Pc2(EP)4, the absorption of the Fe2Pc2(EP)4/PSS-Gr samples are red shifted from 668 nm to 741 nm, and the absorption of Fe2Pc2(EP)4 dimmers at 621 nm disappeared. This suggests a strong π-π supramolecular interaction between the Fe2Pc2(EP)4 and PSS-GR [36,37,38], which will prevent the aggregation of Fe2Pc2(EP)4 compounds and enhance the π electron density in conjugated structure. Moreover, the strong π-π supramolecular interaction facilitates electron transfer between them, leading to the observed improvement for the oxygen reduction reaction.
To further illustrate the composition and chemical status of the as-prepared catalysts, the Fe2Pc2(EP)4/PSS-Gr were also analyzed by XPS. Figure 4a displays the XPS survey spectra of GO, PSS-Gr, Fe2Pc2(EP)4, and Fe2Pc2(EP)4/PSS-Gr composites. The results showed that the Fe2Pc2(EP)4/PSS-Gr catalysts are composed of O, C, N and Fe elements, which further confirms the existence of Fe2Pc2(EP)4 in the as-prepared samples. Compared with GO, the obviously decreasing O content for PSS-Gr indicates that a relatively high degree of reduction had been achieved during the hydrothermal process. The high-resolution N1s spectrum of the composite Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-Gr are shown in Figure 4c,d. The two asymmetric broad peaks of N1s for Fe2Pc2(EP)4 are located at 398.1 eV and 399.4 eV, which correspond to the signals of C-N and C = N of pyrrolic ring in the phthalocyanine macrocycle, respectively [39,40]. What is more interesting is that the binding energy values of N1s in the Fe2Pc2(EP)4/PSS-Gr composites are obviously higher than those of pure Fe2Pc2(EP)4, which confirms a strong interaction between Fe2Pc2(EP)4 and PSS-Gr.
The high-resolution Fe2p spectrum of the catalysts is shown in Figure 4b. The peaks of Fe2p for Fe2Pc2(EP)4 are located at 723.9 eV and 710.6 eV, which correspond to the signals of Fe2p1/2 and Fe2p3/2 in the bivalent oxidation state, respectively. However, the binding energy values of Fe2p in the composites of Fe2Pc2(EP)4/PSS-Gr are obviously lower than those of pure Fe2Pc2(EP)4 [19]. The shift again confirms a π-π supramolecular interaction between Fe2Pc2(EP)4 and PSS-Gr, indicating the as-prepared composites of Fe2Pc2(EP)4 and PSS-Gr tend to form a hetero structure, rather than a physical mixture.

3.2. Effects of π Electron Conjugated Structure for ORR

The electrocatalytic activity of the M2Pc2(EP)4/PSS-Gr composites for ORR were first tested by the technique of CV. As shown in Figure 5, the ORR peak currents in the voltammograms showed that M2Pc2(EP)4/PSS-Gr composites interact well with O2 through the redox-active character of the M2+ cores. The π electron conjugated structure of the MN4-type phthalocyanine macrocyclic system strongly influences the redox-active character of the M2+ cores. Therefore, because of the d filling t2g6 eg0 of Fe(II) with a fully filled t2g and unoccupied eg orbitals, the central metal Fe(II) was favored to coordinate with dioxygen, and was oxidized to Fe(III) much more easily in the redox process [17]. The results showed that the Fe(II)/Fe(III) reduction peak current of O2 commenced at lower positive potentials (−0.15 V vs. SCE) than that of the Pt/C (−0.17 V vs. SCE). When the Fe(II)/Fe(III) redox transition occurs at low positive potentials, highly acidic Fe(III) species well interact well with dioxygen and provide a relatively low overpotential for ORR. Moreover, the reduction potential of Fe(III)/Fe(II) (−0.15 V vs. SCE) is more positive than that of Co(III)/Co(II) (−0.21 V vs. SCE) and Zn(III)/Zn(II)(−0.59V vs. SCE). The results indicated that the electrocatalytic activity is closely related to their radius and d filling of the active center ions. Zn2Pc2(EP)4/PSS-Gr shows a relatively low catalytic activity for ORR because of the fully filled t2g6 and eg4 orbitals, which make Zn(II) difficult to be oxidized to Zn(III) by the O2 in the vertical direction of the conjugate plane in a strong ligand-field. Whereas the ORR process occurs only on the phthalocyanine ring, and is independent of the central metal Zn(II).
In order to further investigate the influence of the catalysts structures for ORR, the linear sweep voltammetry (LSV) measurement was performed on a rotating disk electrode (RDE) at a scanning rate of 5 mV−1 in O2-saturated 0.1 M KOH solution with the rotational speed from 400 rpm to 2500 rpm. A comparison of the LSV results was recorded at 1600 rpm rotational speed using Pt/C, PSS-Gr, Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-Gr modified electrodes individually. The onset potential (E0) and the limiting diffusion current density (Jl) were taken as measures of the catalytic activity. Compared with the ORR potentials of PSS-Gr (−0.17 V vs. SCE) and Fe2Pc2(EP)4 (−0.27 V vs. SCE), the onset potential of Fe2Pc2(EP)4/Gr was positively shifted to −0.09 V, which is close to the onset potential of Pt/C (−0.07 V). The results indicated that the electrocatalytic activity of Fe2Pc2(EP)4/PSS-Gr was enhanced by the π-π supramolecular interaction between Fe2Pc2(EP)4 compounds and PSS-Gr, which enhance the π electron density in Pc2(EP)4 conjugated structure, leading to an observed improvement for the oxygen reduction reaction [41,42].
Furthermore, it is well known that a one-step four-electron process has more excellent electrocatalytic performances than the two-electron process for an oxygen reduction reaction [43,44,45]. The total electron transfer number (n) in the ORR reaction is calculated by the Koutecky-Levich (K-L) equation given below (1) and (2):
1 J = 1 J K + 1 J L = 1 n F K C o + 1 B ω 1 / 2 ,
B = 0.62 n F C o ( D 0 ) 2 / 3 ν 1 / 6 ,
where J (mA/cm2) is the measured current density; JK and JL (mA/cm2) are the kinetic and diffusion-controlled current density, respectively; ω is the angular velocity of the rotating disk (ω = 2πN, N is the linear rotation speed in rpm); n is the total number of electron transferred per oxygen molecule in the ORR reaction; F is the Faraday constant; C0 is the bulk oxygen concentration; D0 is the diffusion coefficient of oxygen; and ν is the kinematic viscosity of the electrolyte.
The K-L points (J−1 vs. ω−1/2) of M2Pc2(EP)4/PSS-Gr at different voltages an exhibited excellent linearity and the slope is consistent (Figure 6). The linearity of the K-L plots and the near parallelism of the fitting lines suggested first-order reaction kinetics for ORR. The electron transfer number n is further calculated by the Koutecky-Levich (K-L) equation. The n for Fe2Pc2(EP)4/PSS-Gr was 3.89 at the voltage range from −0.4 V to −0.7 V, and was similar in the redox process at different potentials. The results indicated that the ORR mainly proceeded a one-step four electron process for Fe2Pc2(EP)4/PSS-Gr which is similar to the Pt/C catalysts.
The cyclic voltammetry curves of Pt/C and Fe2Pc2(EP)4/PSS-Gr were further investigated, revealing reveal the cross-effect in an O2 saturated 0.1 M NaOH solution containing 3 M CH3OH. As shown in Figure 7, the oxygen reduction peak of Pt/C catalyst at −0.20 V decreased significantly for the oxygen reduction reaction after adding methanol into the system, and a methanol oxidation peak appeared at 0.0 V. However, the peak current density and peak potential had no significant difference for the Fe2Pc2(EP)4/PSS-Gr catalyst under the same conditions. The results indicate that the Fe2Pc2(EP)4/Gr catalyst had a good methanol-tolerant performance in an alkaline medium in the presence of methanol.
A mechanism was proposed for ORR catalyzed by Fe2Pc2(EP)4/PSS-Gr based on the experiment results and references (Figure 8). The electron transfer number n for Fe(II)2Pc2(EP)4/PSS-Gr was 3.89 which was calculated by the Koutecky-Levich (K-L) equation. The results indicated that ORR mainly underwent a direct four electron pathway to result in OH production. First, the O2 molecule was bonded to the central metal ion Fe(II) (d-filling of t2g6 eg0) of the MN4-type Fe(II)2Pc2(EP)4 macrocyclic system by bridge adsorption [16,17]. Bridge adsorption can coordinate one oxygen molecule with two central metal ions Fe(II), so it can form more stable peroxide intermediates, which are more conducive to oxygen-oxygen bond (O-O) breaking [25,46,47]. The electrons on the π electron conjugated structure Pc2(EP)4 migrate to the central metal ion Fe(II) and then to the O2 molecule, to form an adduct Fe(III)2Pc2(EP)4·O2, which showed the structure of Fe(III)-O-O-Fe(III) peroxo-species. The breaking of the O-O linkage for Fe(III)-O-O-Fe(III) peroxo species is expected to facilitate in the formation of OH ions. The electrons on PSS-Gr then migrated to Fe(III)2Pc2(EP)4 and Fe(III)2Pc2(EP)4 was reduced to Fe(II)2Pc2(EP)4 [19,32,33]. Therefore, the π electron conjugated structure of the MN4-type phthalocyanine macrocyclic system strongly influenced the one-step four-electron electrocatalytic process for ORR, and it effectively reduced the overpotential of the oxide reduction reaction [25]. Moreover, the performance of M2Pc2(EP)4 catalysts was lower than that of the metallophthalocyanines with trifluoro methyl linkages [25]. The linkage of highly electrophilic groups, like trifluoro methyl groups, to the macrocycles dramatically enhanced the electrocatalytic performance. The comparison of the performances of M2Pc2(EP)4 catalysts used in this work and in the reported article also points out the importance of the bridging units in the ball-type structure. More significantly, PSS-Gr dramatically enhanced the electrocatalytic activity of M2Pc2(EP)4. PSS-Gr provide pathway for fast electron transferring and to prevent the aggregation of M2Pc2(EP)4 catalysts. M2Pc2(EP)4 were loaded on the surface of PSS-Gr to enhance the catalytic activity and stability for the ORR, based on the π-π supramolecular interaction between MPcs molecules and graphene. The results indicated that PSS-Gr enhanced the catalytic activity and stability of M2Pc2(EP)4 for the ORR based on the π-π supramolecular interaction.

4. Conclusions

Composites of PSS-graphene-wrapped binuclear ball-type metallophthalocyanines with methoxy substituents (M2Pc2(EP)4, M = Fe(II), Co(II) and Zn(II)) were synthesized to enhanced the electrocatalytic activity for the oxygen reduction reaction of M2Pc2(EP)4. Compared to the commercial Pt/C catalysts, the M2Pc2(EP)4/PSS-Gr composites had a high electrocatalytic activity. The π electron conjugated structure of the MN4-type phthalocyanine macrocyclic system strongly influenced the four-electron electrocatalytic process. PSS-Gr enhance the catalytic activity and stability of the M2Pc2(EP)4 composites, based on the π-π supramolecular interaction between MPcs molecules and graphene. PSS-Gr provide a pathway for fast electron transferring and prevent the aggregation of M2Pc2(EP)4 catalysts. The results indicated that the catalytic performance of M2Pc2Rn could be enhanced by the modification of the π electron conjugated structure of M2Pc2(EP)4 and carbon materials.

Author Contributions

Conceptualization, G.Z., and L.B.; validation, G.Z., L.B.L., and Y.Z.; formal analysis, G.Z.; data curation, W.Z.; writing—original draft preparation, B.L.; writing—review and editing, G.Z., and W.Z.; visualization, T.L.; supervision, W.C.; project administration, G.Z.; funding acquisition, G.Z., W.Z. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Acknowledgments

This research was supported by the Natural Science Foundation of Shaanxi Province (No. 2019JM-527), the National Natural Science Foundation of China (61604120, 21501139).

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Guo, Y.; Jiang, Z.Q.; Wang, X.B.; Ying, W.; Chen, D.; Liu, S.H. Zwitterion threaded metal–organic framework membranes for direct methanol fuel cells. J. Mater. Chem. A 2018, 6, 19547–19554. [Google Scholar] [CrossRef]
  2. Gago, A.S.; Acosta, D.M.; Arriaga, L.G.; Vante, N.A. Carbon supported ruthenium chalcogenide as cathode catalyst in a microfluidic formic acid fuel cell. J. Power. Sources 2011, 196, 1324–1328. [Google Scholar] [CrossRef]
  3. Gong, L.Y.; Yang, Z.Y.; Li, K.; Xing, W.; Liu, C.P.; Ge, J.J. Recent development of methanol electrooxidation catalysts for direct methanol fuel cell. J. Energy. Chem. 2018, 27, 1618–1628. [Google Scholar] [CrossRef]
  4. Ge, X.; Liu, Y.; Goh, F.T.; Hor, T.A.; Zong, Y.; Xiao, P. Dual-phase spinel MnCo2O4 and spinel MnCo2O4/nanocarbon hybrids for electrocatalytic oxygen reduction and evolution. ACS. Appl. Mater. Interfaces 2014, 6, 12684–12691. [Google Scholar] [CrossRef] [PubMed]
  5. Xu, S.; Kim, Y.; Park, J.; Higgins, D.; Shen, S.J.; Schindler, P. Extending the limits of Pt/c catalysts with passivation-gas-incorporated atomic layer deposition. Nat. Cat. 2018, 1, 624–630. [Google Scholar] [CrossRef]
  6. Rosli, N.F.; Carmen, C.; Martinez, M.; Latiff, N.M. Layered PtTe2 Matches Electrocatalytic Performance of Pt/C for Oxygen Reduction Reaction with Significantly Lower Toxicity. ACS. Sustain. Chem. Eng. 2018, 6, 7432–7441. [Google Scholar] [CrossRef]
  7. Whittingham, M.S. Lithium batteries and cathode materials. Chem. Rev. 2018, 104, 4271–4302. [Google Scholar] [CrossRef]
  8. Morozan, A.; Campidelli, S.; Filoramo, A.; Jousselme, B.; Palacin, S. Catalytic activity of cobalt and iron phthalocyanines or porphyrins supported on different carbon nanotubes towards oxygen reduction reaction. Carbon 2011, 49, 4839–4847. [Google Scholar] [CrossRef]
  9. Özer, L.M.; Altındal, A.; Özkaya, A.R.; Salih, B.; Bekaroglu, Ö. Synthesis, characterization, OFET and electrochemical properties of novel dimeric metallophthalocyanines. Dalton. Trans. 2013, 42, 6633–6644. [Google Scholar] [CrossRef]
  10. Zhang, R.L.; Wang, J.; Xu, B.; Huang, X.Y.; Xu, Z.; Zhao, J.S. Investigation of binuclear metal phthalocyanines as electrocatalysts for Li/SOCl2 battery. J. Electrochem. Soc. 2012, 159, H704–H710. [Google Scholar] [CrossRef]
  11. Moraes, F.C.; Cabral, M.F.; Machado, S.A.; Mascaro, L.H. Electrocatalytic Behavior of Glassy Carbon Electrodes Modified with Multiwalled Carbon Nanotubes and Cobalt Phthalocyanine for Selective Analysis of Dopamine in Presence of Ascorbic Acid. Electroanalysis 2008, 20, 851–857. [Google Scholar] [CrossRef]
  12. Odabaş, Z.; Altındal, A.; Özkaya, A.R.; Salih, B.; Bekaroglu, Ö. Novel ball-type homo-and hetero-binuclear phthalocyanines with four 1, 10- methylenedinaphthalen-2-ol bridges: Synthesis and characterization, electrical and gas sensing properties and electrocatalytic performance towards oxygen reduction. Sens. Actuators B Chem. 2010, 145, 355–366. [Google Scholar] [CrossRef]
  13. Hyun, K.; Ueno, T.; Panomsuwan, G.; Li, O.L.; Saito, N. Heterocarbon nanosheets incorporating iron phthalocyanine for oxygen reduction reaction in both alkaline and acidic media. Phys. Chem. Chem. Phys. 2016, 18, 10856–10863. [Google Scholar] [CrossRef] [PubMed]
  14. Xu, G.F.; Li, Z.F.; Wang, S. Planar polyphthalocyanine cobalt absorbed on carbon black as stable electrocatalysts for direct methanol fuel cell. J. Power. Sources 2010, 195, 4731–4735. [Google Scholar] [CrossRef]
  15. Chen, J.M.; Zou, K.Y.; Ding, P.; Deng, J. Conjugated Cobalt Polyphthalocyanine as the Elastic and Reprocessable Catalyst for Flexible Li-CO2 Batteries. Adv. Mater. 2018, 31, 1805484. [Google Scholar] [CrossRef] [PubMed]
  16. Gu, J.Y.; Cai, Z.F.; Wang, D. Single molecular imaging of Iron-Phthalocyanine catalyzed oxygen reduction reaction by in situ scanning tunneling microscopy. ACS Nano 2016, 10, 8746–8750. [Google Scholar] [CrossRef] [PubMed]
  17. Xu, Z.W.; Kang, L.; Wang, R.Y.; Duan, X.T.; Liu, Q.Q.; Zhang, R.L. Electrochemical Effects of Lithium-Thionyl Chloride Battery by Central Metal Ions of Phthalocyanines-Tetraacetamide Complexes. J. Electrochem. Soc. 2017, 164, A3628–A3632. [Google Scholar] [CrossRef]
  18. Peng, Y.X.; Li, Z.P.; Xia, D.G.; Zheng, L.R.; Liao, Y.; Li, K. Probing the influence of the center atom coordination structure in iron phthalocyanine multi-walled carbon nanotube-based oxygen reduction reaction catalysts by X-ray absorption fine structure spectroscopy. J. Power. Sources 2015, 291, 20–28. [Google Scholar] [CrossRef]
  19. Li, T.; Peng, Y.; Li, K.; Zhang, R.; Zheng, L.; Xia, D. Enhanced activity and stability of binuclear iron (III) phthalocyanine on graphene nanosheets for electrocatalytic oxygen reduction in acid. J. Power. Sources 2015, 293, 511–518. [Google Scholar] [CrossRef]
  20. Yasemin, C.; Emel, E.; Fatih, D.; Ali, R.Ö.; Bekir, S.; Özer, B. Synthesis, characterization, electrochemistry and VOC sensingproperties of novel ball-type dinuclear metallophthalocyanines. Sens. Actuators B 2014, 202, 1137–1147. [Google Scholar]
  21. Kakı, E.; Altındal, A.; Salih, B.; Bekaroğlu, Ö. Synthesis, characterization and gas sensing properties of novel homo and hetero binuclear ball-type phthalocyanines. Dalton. Trans. 2015, 44, 8293–8299. [Google Scholar]
  22. Tolbin, A.Y.; Ivanov, A.V.; Tomilova, L.G.; Zefirov, N.S. Synthesis of 1,2-bis(3,4-dicyanophenoxymethyl)benzene and binuclear zinc phthalocyaninesof clamshell and ball types. J. Porphyr. Phthalocyan 2003, 7, 162–166. [Google Scholar] [CrossRef]
  23. Tolbin, A.Y.; Ivanov, A.V.; Tomilova, L.G.; Zefirov, N.S. Preparation of 1,2-bis(3,4-dicyanophenoxymethyl)benzene and the binuclear zinc phthalocyaninederived from it. Mendeleev. Commun. 2002, 12, 96–97. [Google Scholar] [CrossRef]
  24. Bekaro˘glu, Ö.; Jiang, J. Functional Phthalocyanine Molecular Materials; Springer: Berlin/Heidelberg, Germany, 2010; Volume 135, pp. 105–136. [Google Scholar]
  25. Git, N.K.; Özen, Ü.E.; Özer, M.; Salih, B.; Özkaya, A.R.; Glu, Ö.B. Electrocatalytic Activity of Novel Ball-Type Metallophthalocyanines with Trifluoro Methyl Linkages in Oxygen Reduction Reaction and Application as Zn-Air Battery Cathode Catalyst. Electrochim. Acta 2017, 233, 237–248. [Google Scholar]
  26. Beck, F.; Dammert, W.; Beiss, J.; Hiller, H.; Tolster, R. Electrocatalysis of oxygen cathode by metal-phthalocyanine and metal-dibenzotetraazaannulene. Z. Naturforsch. 1973, 28, 1009–1021. [Google Scholar]
  27. Oliveira, M.A.C.; Mecheri, B.; D’Epifanio, A.; Placidi, E.; Arciprete, F.; Valentini, F. Graphene oxide nanoplatforms to enhance catalytic performance of iron phthalocyanine for oxygen reduction reaction in bioelectrochemical systems. J. Power. Sources. 2017, 356, 381–388. [Google Scholar] [CrossRef]
  28. Liu, X.M.; Xu, T.; Li, Y.L.; Zang, Z.G.; Peng, X.S.; Wei, H.Y. Enhanced X-ray photon response in solution-synthesized CsPbBr3 nanoparticles wrapped by reduced graphene oxide. Sol. Energy Mater. Sol. Cells 2018, 187, 249–254. [Google Scholar] [CrossRef]
  29. Liu, L.; Zheng, K.; Yan, Y.; Cai, Z.H.; Lin, S.X.; Hu, X.B. Graphene Aerogels Enhanced Phase Change Materials prepared by one-pot method with high thermal conductivity and large latent energy storage. Sol. Energy Mater. Sol. Cells 2018, 185, 487–493. [Google Scholar] [CrossRef]
  30. Kusuma, J.; Balakrishna, R.G.; Patil, S.; Jyothi, M.S.; Chandan, H.R.; Shwetharani, R. Exploration of Graphene oxide nanoribbons as excellent electron conducting network for third generation solar cells. Sol. Energy Mater. Sol. Cells 2018, 183, 211–219. [Google Scholar] [CrossRef]
  31. Dai, L.M.; Chang, D.W.; Baek, J.B.; Lu, W. Carbon Nanomaterials for Advanced Energy Conversion and Storage. Small 2012, 8, 1130–1166. [Google Scholar] [CrossRef]
  32. Cui, L.; Lv, G.; Dou, Z. Fabrication of iron phthalocyanine/Graphene micro/nanocomposite by solvothermally assisted π–π assembling method and its application for oxygen reduction reaction. Electrochim. Acta 2013, 106, 272–278. [Google Scholar] [CrossRef]
  33. Zhang, X.; Feng, Y.; Tang, S.; Feng, W. Preparation of a Graphene oxide–phthalocyanine hybrid through strong π–π interactions. Carbon 2010, 48, 211–216. [Google Scholar] [CrossRef]
  34. Zhang, G.; Liu, B.L.; Zhou, H.W.; Yang, Y.; Chen, W.X.; Zhao, J.S. Graphene Wrapped Phthalocyanine: Enhanced Oxidative Desulfurization for Dibenzothiophene in Fuel. Appl. Organometallic. Chem. 2018, 32, a4477. [Google Scholar] [CrossRef]
  35. Liu, D.; Peng, J.H.; Li, Z.Y.; Liu, B.; Wang, L. Improvement in the mechanical properties, proton conductivity, and methanol resistance of highly branched sulfonated poly(arylene ether)/Graphene oxide Grafted with flexible alkylsulfonated side chains nanocomposite membranes. J. Power. Sources 2018, 378, 451–459. [Google Scholar] [CrossRef]
  36. Zhang, Y.; Wu, H.K.; Zhao, W.; Li, X.M.; Yin, R.; Qian, L. Iron (II) phthalocyanine nanoclusters - Graphene sandwich composite for oxygen reduction reaction catalysts. Mater. Des. 2017, 130, 366–372. [Google Scholar] [CrossRef]
  37. Cao, R.G.; Thapa, R.; Kim, H.; Xu, X.D.; Kim, M.G.; Li, Q. Promotion of oxygen reduction by a bio-inspired tethered iron phthalocyanine carbon nanotube-based catalyst. Nat. Commun. 2013, 4, 2076. [Google Scholar] [CrossRef] [Green Version]
  38. Järvinen, P.; Sampsa, K.; Hämäläinen, M.; Harju, A. Self-Assembly and Orbital Imaging of Metal Phthalocyanines on a Graphene Model Surface. J. Phys. Chem. C 2014, 118, 13320–13325. [Google Scholar] [CrossRef]
  39. Serov, A.; Artyushkova, K.; Andersen, N.I. Original Mechanochemical Synthesis of Non-Platinum Group Metals Oxygen Reduction Reaction Catalysts Assisted by Sacrificial Support Method. Electrochim. Acta 2015, 179, 154–160. [Google Scholar] [CrossRef]
  40. Jaouen, F.; Herranz, J.; Lefèvre, M. Cross-Laboratory Experimental Study of Non-Noble-Metal Electrocatalysts for the Oxygen Reduction Reaction. ACS. Appl. Mater. Interfaces 2009, 1, 1623–1639. [Google Scholar] [CrossRef]
  41. Jin, H.G.; Jiang, X.; Irina, A.; Clair, S.; Valérie, M.; Chendo, C. Microwave-mediated synthesis of bulky lanthanide porphyrin–phthalocyanine triple-deckers: Electrochemical and magnetic properties. ACS Inorg. Chem. 2017, 6, b03056. [Google Scholar] [CrossRef] [Green Version]
  42. Tejerina, L.; Nazeeruddin, M.K.; GRätzel, M.; Torres, T. Role of the bulky aryloxy Group at the non-peripheral position of phthalocyanines for dye sensitized solar cells. ChemPlusChem 2017, 82, 132–135. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  43. Chen, R.; Li, H.; Chu, D. Unraveling Oxygen Reduction Reaction Mechanisms on Carbon-Supported Fe-Phthalocyanine and Co-Phthalocyanine Catalysts in Alkaline Solutions. J. Phys. Chem. C 2009, 113, 20689–20697. [Google Scholar] [CrossRef]
  44. Guo, J.; He, H.; Chu, D. OH-Binding Effects on Metallophthalocyanine Catalysts for O2, Reduction Reaction in Anion Exchange Membrane Fuel Cells. Electrocatalysis 2012, 3, 252–264. [Google Scholar] [CrossRef]
  45. Oberst, J.L.; Thorum, M.S.; Gewirth, A.A. Effect of pH and Azide on the Oxygen Reduction Reaction with a Pyrolyzed Fe Phthalocyanine Catalyst. J. Phys. Chem. C 2018, 116, 25257–25261. [Google Scholar] [CrossRef]
  46. Özen, Ü.E.; Elvan, D.; Özer, M.; Glu, Ö.B.; Özkaya, A.R. Communication—High-Performance and Non-Precious Bifunctional Oxygen Electrocatalysis with Binuclear Ball-Type Phthalocyanine Based Complexes for Zinc-Air Batteries. J. Electrochem. Soc. 2016, 163, A2001–A2003. [Google Scholar] [CrossRef]
  47. Tanaka, A.; Fierro, C.; Scherson, D.; Yaeger, E. Electrocatalytic aspects of iron phthalocyanine and its. mu.-oxo derivatives dispersed on high surface area carbon. J. Phys. Chem. 1987, 91, 3799–3807. [Google Scholar] [CrossRef]
Figure 1. Schematic illustration of the preparation process for the M2Pc2(EP)4/polystyrene sodium sulfonate modified graphene (PSS-Gr) composites.
Figure 1. Schematic illustration of the preparation process for the M2Pc2(EP)4/polystyrene sodium sulfonate modified graphene (PSS-Gr) composites.
Nanomaterials 10 00946 g001
Figure 2. TEM and SEM images of PSS-Gr and Fe2Pc2(EP)4/PSS-Gr; (a), (c) TEM and SEM images of PSS-Gr; (b), (d) TEM and SEM images of Fe2Pc2(EP)4/PSS-Gr.
Figure 2. TEM and SEM images of PSS-Gr and Fe2Pc2(EP)4/PSS-Gr; (a), (c) TEM and SEM images of PSS-Gr; (b), (d) TEM and SEM images of Fe2Pc2(EP)4/PSS-Gr.
Nanomaterials 10 00946 g002
Figure 3. (a) UV-Vis spectra of Fe2Pc2(EP)4, Co2Pc2(EP)4, and Zn2Pc2(EP)4, and (b) UV-vis spectra of Fe2Pc2(EP)4/PSS-Gr, Fe2Pc2(EP)4 and PSS-Gr.
Figure 3. (a) UV-Vis spectra of Fe2Pc2(EP)4, Co2Pc2(EP)4, and Zn2Pc2(EP)4, and (b) UV-vis spectra of Fe2Pc2(EP)4/PSS-Gr, Fe2Pc2(EP)4 and PSS-Gr.
Nanomaterials 10 00946 g003
Figure 4. X-ray photoelectron spectroscopy (XPS) spectra of Fe2Pc2(EP)4/PSS-Gr; (a) XPS survey spectra of GO, PSS-Gr, Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-GR; (b), (c), (d) High resolution of Fe2p, N1s XPS spectra of Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-Gr.
Figure 4. X-ray photoelectron spectroscopy (XPS) spectra of Fe2Pc2(EP)4/PSS-Gr; (a) XPS survey spectra of GO, PSS-Gr, Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-GR; (b), (c), (d) High resolution of Fe2p, N1s XPS spectra of Fe2Pc2(EP)4 and Fe2Pc2(EP)4/PSS-Gr.
Nanomaterials 10 00946 g004
Figure 5. Cyclic Voltammograms curve of M2Pc2(EP)4/PSS-Gr and Pt/C catalysts on glassy carbon electrodes; (a), (b), (c), (d) CV curve of Fe2Pc2(EP)4/PSS-Gr, Pt/C, Zn2Pc2(EP)4/PSS-Gr, and Fe2Pc2(EP)4/PSS-Gr;
Figure 5. Cyclic Voltammograms curve of M2Pc2(EP)4/PSS-Gr and Pt/C catalysts on glassy carbon electrodes; (a), (b), (c), (d) CV curve of Fe2Pc2(EP)4/PSS-Gr, Pt/C, Zn2Pc2(EP)4/PSS-Gr, and Fe2Pc2(EP)4/PSS-Gr;
Nanomaterials 10 00946 g005
Figure 6. Electrocatalytic activities of Pt/C and Fe2Pc2(EP)4/PSS-Gr at different rotation speed in O2-saturated 0.1 M KOH; (a), (c), (e), (g) the linear sweep voltammetry (LSV) curve; (b), (d), (f) Koutecky-Levich (K-L) plots; (h) the number of electrons transferred.
Figure 6. Electrocatalytic activities of Pt/C and Fe2Pc2(EP)4/PSS-Gr at different rotation speed in O2-saturated 0.1 M KOH; (a), (c), (e), (g) the linear sweep voltammetry (LSV) curve; (b), (d), (f) Koutecky-Levich (K-L) plots; (h) the number of electrons transferred.
Nanomaterials 10 00946 g006aNanomaterials 10 00946 g006b
Figure 7. Cyclic voltammetry (CV) curves of Fe2Pc2(EP)4/PSS-Gr in O2-saturated in a 0.1 M KOH solution and O2-saturated 0.1 M KOH solution with 3 M methanol. (a) Pt/C, and (b) Fe2Pc2(EP)4/Gr.
Figure 7. Cyclic voltammetry (CV) curves of Fe2Pc2(EP)4/PSS-Gr in O2-saturated in a 0.1 M KOH solution and O2-saturated 0.1 M KOH solution with 3 M methanol. (a) Pt/C, and (b) Fe2Pc2(EP)4/Gr.
Nanomaterials 10 00946 g007
Figure 8. Mechanism for the oxygen reduction reaction (ORR) catalyzed by Fe2Pc2(EP)4/PSS-Gr.
Figure 8. Mechanism for the oxygen reduction reaction (ORR) catalyzed by Fe2Pc2(EP)4/PSS-Gr.
Nanomaterials 10 00946 g008

Share and Cite

MDPI and ACS Style

Zhang, G.; Liu, B.; Zhang, Y.; Li, T.; Chen, W.; Zhao, W. Study on the Effects of a π Electron Conjugated Structure in Binuclear Metallophthalocyanines Graphene-Based Oxygen Reduction Reaction Catalysts. Nanomaterials 2020, 10, 946. https://doi.org/10.3390/nano10050946

AMA Style

Zhang G, Liu B, Zhang Y, Li T, Chen W, Zhao W. Study on the Effects of a π Electron Conjugated Structure in Binuclear Metallophthalocyanines Graphene-Based Oxygen Reduction Reaction Catalysts. Nanomaterials. 2020; 10(5):946. https://doi.org/10.3390/nano10050946

Chicago/Turabian Style

Zhang, Gai, Bulei Liu, Yufan Zhang, Tiantian Li, Weixing Chen, and Weifeng Zhao. 2020. "Study on the Effects of a π Electron Conjugated Structure in Binuclear Metallophthalocyanines Graphene-Based Oxygen Reduction Reaction Catalysts" Nanomaterials 10, no. 5: 946. https://doi.org/10.3390/nano10050946

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop