Search Results (21)

Printed electronics employ established printing methods to create low-cost, mechanically flexible devices including batteries, supercapacitors, sensors, antennas and RFID tags on plastic, paper and textile substrates. This review focuses on the specific contribution of screen printing to that landscape, examining how ink viscosity, mesh selection and squeegee dynamics govern film uniformity, pattern resolution and ultimately device performance. Recent progress in advanced ink systems is surveyed, highlighting carbon allotropes (graphene, carbon nano-onions, carbon nanotubes, graphite), silver and copper nanostructures, MXene and functional oxides that collectively enhance mechanical robustness, electrical conductivity and radio-frequency behavior. Parallel improvements in substrate engineering such as polyimide, PET, TPU, cellulose and elastomers demonstrate the technique’s capacity to accommodate complex geometries for wearable, medical and industrial applications while supporting environmentally responsible material choices such as water-borne binders and bio-based solvents. By mapping two decades of developments across energy-storage layers and functional electronics, the article identifies the key process elements, recurring challenges and emerging sustainable practices that will guide future optimization of screen-printing materials and protocols for high-performance, customizable and eco-friendly flexible devices. Full article

Radio Frequency Identification (RFID) assistive systems, which integrate RFID devices with IoT technologies, are vital for enhancing the independence, mobility, and safety of individuals with disabilities. These systems enable applications such as RFID navigation for blind users and RFID-enabled canes that provide real-time location data. Central to these systems are resource-constrained RFID devices that rely on RFID tags to collect and transmit data, but their limited computational capabilities make them vulnerable to cyberattacks, jeopardizing user safety and privacy. Implementing the Elliptic Curve Cryptography (ECC) algorithm is essential to mitigate these risks; however, its high computational complexity exceeds the capabilities of these devices. The fundamental operation of ECC is finite field multiplication, which is crucial for securing data. Optimizing this operation allows ECC computations to be executed without overloading the devices’ limited resources. Traditional multiplication designs are often unsuitable for such devices due to their excessive area and energy requirements. Therefore, this work tackles these challenges by proposing an efficient and compact field multiplier design optimized for the Montgomery multiplication algorithm, a widely used method in cryptographic applications. The proposed design significantly reduces both space and energy consumption while maintaining computational performance, making it well-suited for resource-constrained environments. ASIC synthesis results demonstrate substantial improvements in key metrics, including area, power consumption, Power-Delay Product (PDP), and Area-Delay Product (ADP), highlighting the multiplier’s efficiency and practicality. This innovation enables the implementation of ECC on RFID assistive devices, enhancing their security and reliability, thereby allowing individuals with disabilities to engage with assistive technologies more safely and confidently. Full article

Wearable collar technologies have become integral to the advancement of precision livestock farming, revolutionizing how dairy cattle are monitored in terms of their behaviour, health status, and productivity. These devices leverage cutting-edge sensors, including accelerometers, RFID tags, GPS receivers, microphones, gyroscopes, and magnetometers, to provide non-invasive, real-time insights that enhance animal welfare, optimize resource use, and support decision-making processes in livestock management. This systematized review focuses on analyzing the sensors integrated into collar-based systems, detailing their functionalities and applications. However, significant challenges remain, including the high energy consumption of some sensors, the need for frequent recharging, and limited parameter coverage by individual devices. Future developments must focus on integrating multiple sensor types into unified systems to provide comprehensive data on animal behaviour, health, and environmental interactions. Additionally, advancements in energy-efficient designs, longer battery life, and cost-reduction strategies are essential to enhance the practicality and accessibility of these technologies. By addressing these challenges, wearable collar systems can play a pivotal role in promoting sustainable, efficient, and responsible livestock farming, aligning with global goals for environmental and economic sustainability. This paper underscores the transformative potential of wearable collar technologies in reshaping the livestock industry and driving the adoption of innovative farming practices worldwide. Full article

This paper presents a passive displacement sensor based on the inductive coupling between a printed UHF RFID tag and a metallic strip. The sensor operates by exploiting variations in mutual inductive coupling, which modulate the tag impedance and transmission coefficient, thereby altering the backscattered signal strength and the maximum read range of the RFID tag. The performance of the sensor is validated through simulations and experiments, which demonstrate a sensitivity characterized by an approximately 9 dB reduction in the received signal strength indicator (RSSI) and a 2.3 m decrease in the read range within the first 12 mm of displacement. Furthermore, its potential for wearable applications is showcased through respiratory monitoring, where RSSI variations of approximately 5 dB are observed between the inspiration and expiration phases when positioned on the abdominal region of a volunteer. Thus, the proposed displacement sensing approach offers a cost-effective and battery-free solution for wearable applications with remote monitoring capabilities. Full article

The objectives of this study were to design, investigate, and compare different designs of coupling circuits for textronic RFID transponders, particularly focusing on magnetic coupling between an antenna and a chip. The configuration of the inductively coupled antenna module and the microelectronic module housing the chip can be varied in several ways. This article explores various geometries of coupling circuits and assesses the effects of altering their dimensions on mutual inductance, chip voltage, and the transponder’s read range. The investigation comprised an analytical description of inductive coupling, calculations of mutual inductance and chip voltage based on simulation models of transponders, and laboratory measurements of the read range for selected configurations. The results obtained from this study demonstrate that various designs of textile transponders are capable of achieving satisfactory read ranges, with some configurations extending beyond 10 m. This significant range provides clothing designers with the flexibility to select transponder designs that best meet their specific aesthetic and functional requirements. Full article

A platform-tolerant RFID (Radio-Frequency Identification) tag is presented, designed to operate across the entire RFID band. This tag utilizes a small Artificial Magnetic Conductor (AMC) structure as a shielding element for an ungrounded RFID tag antenna. It can be easily mounted on various surfaces, including low permittivity dielectric materials, metal objects, or even attached to the human body for wearable applications. The key features of this RFID tag include its ability to be tuned within the worldwide RFID band, achieving a maximum theoretical read range of over 11 m. Despite its advanced capabilities, the design emphasizes simplicity and cost-effective manufacturing. The design and simulations were conducted using CST Studio Suite. Full article

The aim of this paper is to demonstrate progress in textronic UHF RFID transponder (RFIDtex tag) technology. The fundamental idea behind the RFIDtex tag design involves galvanic separation between circuits of the sewn antenna and the chip, which are electromagnetically coupled through a system of inductive loops. To advance the development of this concept, it is crucial to detect factors affecting the performance of the transponders. To achieve this goal, a mathematical model of the textronic UHF RFID transponder was developed. It involves relationships that describe the impedance of each element, the mutual inductance of the loops, and the chip voltage, and it enables the exploration of the influence of these variables on general parameters such as impedance matching and read range. Various analytical and numerical approaches were considered to obtain the value of the mutual inductance of the loops. The dimensions and geometry of the antenna, as well as the matching circuit in the microelectronic module, were taken into account. Based on the mathematical model, it was determined that mutual inductance strongly affects the chip voltage for frequencies higher than 800 MHz. The calculations from the mathematical model were compared with numerical simulations. Experimental studies were also conducted to investigate how the transponder performance is affected by either the distance between the centers of the loops or the conductivity of the threads used to embroider the antenna. The measurement results allowed us to conclude that even small imperfections in the manufacturing of the transponder, which slightly increase the vertical or horizontal distance between the centers of the loops, cause a dramatic decrease in the mutual inductance and coupling coefficient, significantly impacting the transponder’s performance. Full article

Radio frequency identification (RFID) tags are small, low-cost, wearable, and wireless sensors that can detect movement in structures, humans, or robots. In this paper, we use passive RFID tags for structural health monitoring by detecting displacements. We employ a novel process of using 3D printable embedded passive RFID tags within uniform linear arrays together with the multiple signal classification algorithm to estimate the direction of arrival using only the phase of the backscattered signals. We validate our proposed approach via data collected from real-world experiments using a unipolar RFID reader antenna and both narrowband and wideband measurements. Full article

In the context of wearable technology, several techniques have been used for the fabrication of radio frequency identification (RFID) tags such as 3D printing, inkjet printing, and even embroidery. In contrast to these methods where the tag is attached to the object by using sewing or simple sticking, the E-Thread^® technology is a novel assembling method allowing for the integration of the RFID tag into a textile yarn and thus makes it embeddable into the object at the fabrication stage. The current E-Thread^® yarn uses a RFID tag in which the antenna is a straight half-wave dipole that makes the solution vulnerable to mechanical strains (i.e., elongation). In this paper, we propose an alternative to the current RFID yarn solution with the use of an antenna having a helical geometry that answers to the mechanical issues and keeps quite similar electrical and radiative properties with respect to the present solution. The RFID helical tag was designed and simulated taking into consideration the constraints of the manufacturing process. The helical RFID tag was then fabricated using the E-Thread^® technology and experimental characterization showed that the obtained structure exhibited good performance with $10.6 \mathrm{m}$ of read range in the ultra high frequency (UHF) RFID band and $10\%$ of tolerance in terms of elongation. Full article

This paper presents the design of a 920 MHz Ultra High Frequency (UHF) band radio frequency identification (RFID) conductive fabric tag antenna. The DC (Direct Current) resistance and impedance of the conductive fabric are measured by a DC multimeter and by a network analyzer at a UHF frequency band. The conductivities of the fabrics are calculated with their measured DC resistance and impedance values, respectively. The conductivities of the fabric are inserted into the CST simulation program to simulate the fabric tag antenna designs, and the results of the tag designs with two conductivities are compared. Two fabric UHF RFID tag antennas with a T-Matching structure, one with the name-tag size of 80 × 40 mm, and another with 40 × 23 are simulated and measured the characteristics of tag antennas. The simulated and measured results are compared by reflection coefficient S11, radar cross-section and reading range. The reading range of the 80 × 40 mm fabric tag antenna is about 4 m and 0.5 m for the 40 × 23 size tag. These fabric tags can be easily applied to an entrance control system as they can be attached to other fabrics and clothes. Full article

In this paper, a new flexible wearable radio frequency identification (RFID) five-shaped slot patch tag placed on the human arm is designed for ultra-high frequency (UHF) healthcare sensing applications. The compact proposed tag consists of a patch structure provided with five shaped slot radiators and a flexible substrate, which minimize the human body’s impact on the antenna radiation performance. We have optimized our designed tag using the particle swarm optimization (PSO) method with curve fitting within MATLAB to minimize antenna parameters to achieve a good return loss and an attractive radiation performance in the operating band. The PSO-optimized tag’s performance has been examined over the specific placement in some parts of the human body, such as wrist and chest, to evaluate the tag response and enable our tag antenna conception in wearable biomedical sensing applications. Finally, we have tested the robustness of this tag by evaluating its sensitivity as a function of the antenna radiator placement over the ground plane or by shaping the ground plane substrate for the tag’s position from the human body. Our numerical results show an optimal tag size with good matching features and promising read ranges near the human body. Full article

This paper details the design, fabrication and testing of flexible textile-concealed Radio Frequency Identification (RFID) tags for wearable applications in a smart city/smart building environment. The proposed tag designs aim to reduce the overall footprint, enabling textile integration whilst maintaining the read range. The proposed RFID filament is less than 3.5 mm in width and 100 mm in length. The tag is based on an electrically small (0.0033 ${\lambda }^2$ ) high-impedance planar dipole antenna with a tuning loop, maintaining a reflection coefficient less than −21 dB at 915 MHz, when matched to a commercial RFID chip mounted alongside the antenna. The antenna strip and the RFID chip are then encapsulated and integrated in a standard woven textile for wearable applications. The flexible antenna filament demonstrates a 1.8 dBi gain which shows a close agreement with the analytically calculated and numerically simulated gains. The range of the fabricated tags has been measured and a maximum read range of 8.2 m was recorded at 868 MHz Moreover, the tag’s maximum calculated range at 915 MHz is 18 m, which is much longer than the commercially available laundry tags of larger length and width, such as Invengo RFID tags. The reliability of the proposed RFID tags has been investigated using a series of tests replicating textile-based use case scenarios which demonstrates its suitability for practical deployment. Washing tests have shown that the textile-integrated encapsulated tags can be read after over 32 washing cycles, and that multiple tags can be read simultaneously while being washed. Full article

Radio frequency identification (RFID) and wireless sensors networks (WSNs) are two fundamental pillars that enable the Internet of Things (IoT). RFID systems are able to identify and track devices, whilst WSNs cooperate to gather and provide information from interconnected sensors. This involves challenges, for example, in transforming RFID systems with identification capabilities into sensing and computational platforms, as well as considering them as architectures of wirelessly connected sensing tags. This, together with the latest advances in WSNs and with the integration of both technologies, has resulted in the opportunity to develop novel IoT applications. This paper presents a review of these two technologies and the obstacles and challenges that need to be overcome. Some of these challenges are the efficiency of the energy harvesting, communication interference, fault tolerance, higher capacities to handling data processing, cost feasibility, and an appropriate integration of these factors. Additionally, two emerging trends in IoT are reviewed: the combination of RFID and WSNs in order to exploit their advantages and complement their limitations, and wearable sensors, which enable new promising IoT applications. Full article

In the field of pervasive computing, wearable devices have been widely used for recognizing human activities. One important area in this research is the recognition of activities of daily living where especially inertial sensors and interaction sensors (like RFID tags with scanners) are popular choices as data sources. Using interaction sensors, however, has one drawback: they may not differentiate between proper interaction and simple touching of an object. A positive signal from an interaction sensor is not necessarily caused by a performed activity e.g., when an object is only touched but no interaction occurred afterwards. There are, however, many scenarios like medicine intake that rely heavily on correctly recognized activities. In our work, we aim to address this limitation and present a multimodal egocentric-based activity recognition approach. Our solution relies on object detection that recognizes activity-critical objects in a frame. As it is infeasible to always expect a high quality camera view, we enrich the vision features with inertial sensor data that monitors the users’ arm movement. This way we try to overcome the drawbacks of each respective sensor. We present our results of combining inertial and video features to recognize human activities on different types of scenarios where we achieve an $F_1$ -measure of up to 79.6%. Full article

A printable elastic silver ink has been developed, which was made of silver flakes, dispersant, and a fluorine rubber and could be sintered at a low temperature. The printed elastic conductors showed low resistivity at 21 μΩ·cm, which is about 13.2 times of bulk silver (1.59 μΩ·cm). Their mechanical properties were investigated by bending, stretching, and cyclic endurance tests. It was found that upon stretching the resistance of printed conductors increased due to deformation and small cracks appeared in the conductor, but was almost reversible when the strain was removed, and the recovery of conductivity was found to be time dependent. Radio-frequency identification (RFID) tags were fabricated by screen printing the stretchable silver ink on a stretchable fabric (lycra). High performance of tag was maintained even with 1000 cycles of stretching. As a practical example of wearable electronics, an RFID tag was printed directly onto a T-shirt, which demonstrated its normal working order in a wearing state. Full article