Search Results (174)

Carbon-fiber-reinforced plastic (CFRP) machining by ultrashort-pulse lasers promises high precision but is limited due to the heterogeneous epoxy–carbon fiber structure, which creates heat-affected zones and variable kerf quality. This work investigates synthesized copper hydroxyphosphate as a laser-absorbing additive to improve femtosecond (1030 nm) laser ablation of CFRP. Copper hydroxyphosphate particles were synthesized hydrothermally and incorporated into an epoxy matrix to produce single-ply CFRP laminates. Square patterns (0.5 × 0.5 mm) were ablated with a pulse energy of 0.5–16 μJ. Then, ablated volumes were profiled and materials characterized by SEM and EDS. In neat epoxy the copper additive reduced optimum ablation efficiency and decreased penetration depth, while producing smoother, less porous surfaces. In contrast, CFRP with copper hydroxyphosphate showed increased efficiency and higher penetration depth. SEM and EDS analyses indicate more uniform matrix removal and retention of resin residues on fibers. These results suggest that copper hydroxyphosphate acts as a local energy absorber that trades volumetric removal for improved surface quality in epoxy and enhances uniformity and process stability in CFRP femtosecond laser machining. Full article

Ultrashort pulsed laser annealing is an efficient technique for crystallizing amorphous semiconductors with the possibility to obtain polycrystalline films at low temperatures, below the melting point, through non-thermal processes. Here, a multilayer structure consisting of alternating amorphous silicon and germanium films was annealed by mid-infrared (1500 nm) ultrashort (70 fs) laser pulses under single-shot and multi-shot irradiation conditions. We investigate selective crystallization of ultrathin (3.5 nm) a-Ge non-hydrogenated films, which are promising for the generation of highly photostable nanodots. Based on Raman spectroscopy analysis, we demonstrate that, in contrast to thicker (above 10 nm) Ge films, explosive stress-induced crystallization is suppressed in such ultrathin systems and proceeds via thermal melting. This is likely due to the islet structure of ultrathin films, which results in the formation of nanopores at the Si-Ge interface and reduces stress confinement during ultrashort laser heating. Full article

The combination of polypyrrole (PPy) with graphene has attracted extensive attention as a nonlinear optical material with various optoelectronic applications. Here, we describe the development of PPy nanoplates prepared using a simple spin-coating method. The appropriate volume of the dropped PPy solution was determined to be 50 drops by comparing the surface morphologies, chain structures, elementary compositions, and optical properties of PPy saturable absorbers (SAs). The hybrid PPy/graphene heterostructure SA was obtained using the wet transfer process of a graphene layer. This approach led to significant improvements in optical properties, including a ~7.2% increase in linear optical absorption, a 2.5-fold increase in modulation depth, and a third decrease in saturable intensity at 1550 nm due to the additional optical absorption and the π-π interaction between PPy nanoplates and the graphene layer. By inserting the PPy/graphene heterostructure SA into the passively mode-locked fiber laser cavity, 1559 nm ultrashort laser pulses were generated, with an average output power of 1.24 mW, a 815 fs pulse width, and a repetition frequency of 3.26 MHz. Our experimental results demonstrate that the prepared PPy SA has excellent nonlinear optical characteristics, providing a new opportunity for the generation of ultrashort laser pulses. Full article

Femtosecond lasers have evolved continuously over the past three decades, enabling the transition of research from fundamental studies in atomic and molecular physics to the realm of practical applications. In femtosecond laser amplifiers, to ensure strict synchronization between the seed laser pulse and the pump laser, enabling their precise overlap during the amplification process and avoiding a decline in pulse amplification efficiency and the generation of undesired phase noise, this study designed a synchronous timing signal generation system based on the combination of FPGA and analog delay. This system was investigated from three aspects: delay pulse width adjustment within a certain range, precise delay resolution, and external trigger jitter compensation. By using a FPGA digital counter to achieve coarse-delay control over a wide range and combining it with the method of passive precise fine delay, the system can generate synchronous delay signals with a large delay range, high precision, and multiple channels. Regarding the problem of asynchronous phase between the external trigger and the internal clock, a jitter compensation circuit was proposed, consisting of an active gated integrator and an output comparator, which compensates for the uncertainty of trigger timing through analog delay. The verification of this study shows that the system operates stably under an external trigger with a repetition frequency of 80 MHz. The output delay range is from 10 ns to 100 $\mu$s, the coarse-delay resolution is 10 ns, the fine-delay adjustment step is 1.25 ns, and the pulse jitter is reduced from a maximum of 10 ns to the hundred-picosecond level. This meets the requirements of femtosecond laser amplifiers for synchronous trigger signals and offers essential technical support and fundamental assurance for the high-power and high-efficiency amplification of Ti:sapphire ultrashort laser pulses. Full article

Monitoring of laser-based processes is essential for ensuring the quality of produced surface structures and for maintaining the process stability and reproducibility. Optical methods based on scatterometry are attractive for industrial monitoring as they are fast, non-contact, non-destructive, and can resolve features down to the sub-microscale. Here, Laser-Induced Periodic Surface Structures (LIPSS) are produced on stainless steel using ultrashort laser pulses in combination with a polygon scanning system. After the process, the fabricated LIPSS features are characterized by microscopy methods and with an optical setup based on scatterometry. Images of the diffraction patterns are collected and the intensity distribution analyzed and compared to the microscopy results in order to estimate the LIPSS height, spatial period, and regularity. The resulting analysis allows us to study LIPSS formation development, even when its characteristic diffraction pattern gradually changes from a double-sickle shape to a diffuse cloud. The scatterometry setup could be used to infer LIPSS height up to 420 nm, with an estimated average error of 7.7% for the highest structures and 11.4% in the whole working range. Periods estimation presents an average error of ~5% in the range where LIPSS are well-defined. In addition, the opening angle of the LIPSS was monitored and compared with regularity measurements, indicating that angles exceeding a certain threshold correspond to surfaces where sub-structures dominate over LIPSS. Full article

We report on the generation of 1300 nm ultrashort laser pulses via the soliton self-frequency shift in a high-nonlinearity fiber, pumped by the 41.9 MHz, 67.9 fs, 1073 nm femtosecond laser emitted from an Yb-doped fiber laser system. A numerical simulation was applied to investigate the spectral broadening process driven by the soliton self-frequency shift with increased pump power. The experimental results are in good agreement with the numerical results, delivering a 33 mW, 57.8 fs 1300 nm Raman soliton filtered by a longpass filter. The impact of the polarization direction of the injected pump laser on the soliton self-frequency shift process was also further investigated. The root means squares of the Yb-doped fiber laser and the nonlinearly spectral broadened laser were 0.19%@1h and 0.23%@1h, respectively. Full article

In this paper, we develop a peridynamic computational framework to analyze thermomechanical interactions in fractured thin films subjected to ultrashort-pulsed laser excitation, employing nonlocal discrete material point discretization to eliminate mesh dependency artifacts. The generalized Cattaneo–Fourier thermal flux formulation uncovers contrasting dynamic responses: hyperbolic heat propagation ($F_T=0$) generates intensified temperature localization and elevates transient crack-tip stress concentrations relative to classical Fourier diffusion ($F_T=1$). A GSSSS (Generalized Single Step Single Solve) i-Integration temporal scheme achieves oscillation-free numerical solutions across picosecond-level laser–matter interactions, effectively resolving steep thermal fronts through adaptive stabilization. These findings underscore hyperbolic conduction’s essential influence on stress-mediated fracture evolution during ultrafast laser processing, providing critical guidelines for thermal management in micro-/nano-electromechanical systems. Full article

Although thick electrodes hold significant potential for enhancing battery energy density, their practical application is limited by restricted ion transport kinetics. Constructing porous structures within thick electrodes is a widely adopted strategy to address this limitation, but it often compromises mass retention and mechanical integrity. In this study, a microchannel structure that balances the electrochemical and mechanical properties of the electrode was identified through simulation and precisely fabricated using femtosecond laser technology. Furthermore, the ultra-short pulse duration and high pulse energy of femtosecond lasers introduce oxygen vacancies into the electrode material, thereby enhancing its electrical conductivity. The obtained electrode exhibited excellent electrochemical performance under high-rate charging and discharging conditions, achieving significantly enhanced cycling stability and capacity retention, with a capacity 1.99 times greater than that of the unstructured electrode after 100 cycles. Meanwhile, the mechanical stability of the laser-processed electrode was maintained. This study provides new insights into the structural design and processing of the thick electrode and contributes to advancements in the field of energy storage. Full article

Glass-based microfluidic devices are essential for applications such as diagnostics and drug discovery, which utilize their optical clarity and chemical stability. This review systematically analyzes pulsed laser micromachining as a transformative technique for fabricating glass-based microfluidic devices, addressing the limitations of conventional methods. By examining three pulse regimes—long (≥nanosecond), short (picosecond), and ultrashort (femtosecond)—this study evaluates how laser parameters (fluence, scanning speed, pulse duration, repetition rate, wavelength) and glass properties influence ablation efficiency and quality. A higher fluence improves the material ablation efficiency across all the regimes but poses risks of thermal damage or plasma shielding in ultrashort pulses. Optimizing the scanning speed balances the depth and the surface quality, with slower speeds enhancing the channel depth but requiring heat accumulation mitigation. Shorter pulses (femtosecond regime) achieve greater precision (feature resolution) and minimal heat-affected zones through nonlinear absorption, while long pulses enable rapid deep-channel fabrication but with increased thermal stress. Elevating the repetition rate improves the material ablation rates but reduces the surface quality. The influence of wavelength on efficiency and quality varies across the three pulse regimes. Material selection is critical to outcomes and potential applications: fused silica demonstrates a superior surface quality due to low thermal expansion, while soda–lime glass provides cost-effective prototyping. The review emphasizes the advantages of laser micromachining and the benefits of a wide range of applications. Future directions should focus on optimizing the process parameters to improve the efficiency and quality of the produced devices at a lower cost to expand their uses in biomedical, environmental, and quantum applications. Full article

Direct-writing submicron copper circuits on glass with laser precision—without lithography, vacuum deposition, or etching—represents a transformative step in next-generation microfabrication. We present a high-resolution, maskless method for metallizing glass using ultrashort pulse Bessel beam laser processing, followed by silver ion activation and electroless copper plating. The laser-modified glass surface hosts nanoscale chemical defects that promote the in situ reduction of Ag⁺ to metallic Ag⁰ upon exposure to AgNO₃ solution. These silver seeds act as robust catalytic and adhesion sites for subsequent copper growth. Using this approach, we demonstrate circuit traces as narrow as 0.7 µm, featuring excellent uniformity and adhesion. Compared to conventional redistribution-layer (RDL) and under-bump-metallization (UBM) techniques, this process eliminates multiple lithographic and vacuum-based steps, significantly reducing process complexity and production time. The method is scalable and adaptable for applications in transparent electronics, fan-out packaging, and high-density interconnects. Full article

Carbon-fiber-reinforced plastic (CFRP) is a popular material possessing great properties, such as strength, lightness, and resistance to corrosion and the environment. Important steps in the production of various parts made of CFRP are surface structuring, milling, drilling and cutting processes. Here, we propose to use ultrashort pulse lasers to achieve the high-quality, low-heat-affected-zone ablation of CFRP. We investigated the ablation efficiency dependence on the processing parameters, such as the pulse duration, pulse energy and pulse overlap. We showed that good-quality results could be achieved using just low-/mid-average-power femtosecond laser equipment. We also discuss further cutting process optimization possibilities using ultrashort pulse lasers and show the possibility of HAZ-free CFRP cutting by femtosecond laser ablation. Full article

High-order harmonic generation (HHG) in semiconductor thin films from ultrashort mid-infrared laser drivers holds the potential for the realization of integrated sources of extreme ultraviolet light. Here, we demonstrate solid-state HHG in zinc oxide thin films synthesized by the radiofrequency reactive magnetron sputtering process directly on the cleaved facets of optical fibers. Harmonics 3 to 13 of the radiation from a fiber-based laser system delivering 500 kW, 96 fs pulses at 3130 nm are produced in the thin film and guided along the fiber. A proper choice of the laser wavelength and fiber material allows for filtering out the mid-IR pump laser and achieving the HHG mode selection. The possibility to nanostructure the fiber exit by, e.g., focused ion beam milling paves the way to an increased control over the HHG spatial mode. Full article

Fiber-optic tip sensors offer significant potential in biomedical applications due to their high sensitivity, compact size, and resistance to electromagnetic interference. This study focuses on advancing phase demodulation techniques for ultra-short Fabry–Pérot cavities within limited spectral bandwidths to enhance their application in biomedicine and diagnostics. We propose a novel sparse-sampled white-light interferometry system for respiratory monitoring, utilizing a monolithic integrated semiconductor tunable laser for quasi-continuous frequency scanning across 191.2–196.15 THz at a sampling rate of 5 kHz. A four-step phase-shifting algorithm (PSA) ensures precise phase demodulation, enabling high sensitivity for short-cavity fiber-optic sensors under constrained spectral bandwidth conditions. Humidity sensors fabricated via a self-growing polymerization process further enhance the system’s functionality. The experimental results demonstrate the system’s capability to accurately capture diverse breathing patterns—including normal, rapid, and deep states—with fast response and recovery times. These findings establish the system’s potential for real-time respiratory monitoring in clinical and point-of-care settings. Full article

High-order harmonic generation is one of the ways to generate attosecond ultra-short pulses. In order to accurately simulate the high-order harmonic emission, it is necessary to perform fast and accurate calculations on the interaction between the atoms and strong laser fields. The accurate profile of the laser field is obtained from the propagation through the gas target. Under the conditions of longer wavelength driving lasers and higher gas densities, the calculation of the laser field becomes more challenging. In this paper, we utilize the driving laser electric field information obtained from numerically solving the three-dimensional Maxwell’s equations as data for machine learning, enabling the prediction of the propagation process of intense laser fields using an artificial neural network. It is found that the simulation based on frequency domain can improve the accuracy of electric field by two orders of magnitude compared with the simulation directly from time domain. On this basis, the feasibility of the transfer learning scheme for laser field prediction is further studied. This study lays a foundation for the rapid and accurate simulation of the interaction between intense laser and matter by using an artificial neural network scheme. Full article

Graphene oxide (GO) and reduced graphene oxide (rGO) have emerged as robust materials in the development of SAs for erbium-doped fiber lasers (EDFLs). Their exceptional optical properties, such as broadband absorption and fast recovery times, make them ideal candidates for achieving ultrashort pulse operation in EDFLs. With its higher oxygen content, GO offers greater nonlinearity and a tunable absorption spectrum, while rGO, yielded through chemical reduction, exhibits enhanced electrical conductivity and higher saturable absorption. These properties facilitate the generation of ultrashort pulses in EDFLs, which are highly desired for various medical imaging, telecommunications, and material processing applications. This review paper comprehensively analyzes the advancements in GO and rGO SAs in the context of EDFLs for mode-locking and Q-switching applications. The performance of EDFLs utilizing GO and rGO SAs is critically evaluated, focusing on key parameters, such as modulation depth, pulse duration, repetition rate, average power, pulse energy, peak power, and signal-to-noise ratio. Additionally, this review delves into the various synthesis methods of GO and rGO thin film, highlighting their impact on the optical properties and performance of SAs. The discussion on techniques to integrate the SAs into laser cavities includes direct deposition of nanoparticles/thin-film-based SAs, tapered-fiber-based SAs, and D-shaped SAs. Furthermore, the paper explores the challenges encountered during the fabrication of ideal GO and rGO SAs, with issues related to uniformity, stability, and tunability, along with proposed solutions to address these challenges. The insights provided offer valuable guidance for future research aimed at enhancing the performance of EDFLs using GO/rGO SAs. Full article