Search Results (12)

This work presents the theoretical design and finite element modeling of high-sensitivity microcantilevers for biosensing applications, integrating piezoelectric actuation with novel ultrananocrystalline diamond (UNCD) structures. Microcantilevers were designed based on projections to grow a multilayer metal/AlN/metal/UNCD stack on silicon substrates, optimized to detect adsorption of biomolecules on the surface of exposed UNCD microcantilevers at the picogram scale. A central design criterion was to match the microcantilever’s eigenfrequency with the resonant frequency of the AlN-based piezoelectric actuator, enabling efficient dynamic excitation. The beam length was tuned to ensure a ≥2 kHz resonant frequency shift upon adsorption of 1 pg of mass distributed on the exposed surface of a UNCD-based microcantilever. Subsequently, a Gaussian distribution mass function with a variance of 5 µm was implemented to evaluate the resonant frequency shift upon mass addition at a certain point on the microcantilever where a variation from 600 Hz to 100 Hz was observed when the mass distribution center was located at the tip of the microcantilever and the piezoelectric borderline, respectively. Both frequency and time domain analyses were performed to predict the resonance behavior, oscillation amplitude, and quality factor. To ensure the reliability of the simulations, the model was first validated using experimental results reported in the literature for an AlN/nanocrystalline diamond (NCD) microcantilever. The results confirmed that the AlN/UNCD architecture exhibits higher resonant frequencies and enhanced sensitivity compared to equivalent AlN/Si structures. The findings demonstrate that using a UNCD-based microcantilever not only improves biocompatibility but also significantly enhances the mechanical performance of the biosensor, offering a robust foundation for the development of next-generation MEMS-based biochemical detection platforms. The research reported here introduces a novel design methodology that integrates piezoelectric actuation with UNCD microcantilevers through eigenfrequency matching, enabling efficient picogram-scale mass detection. Unlike previous approaches, it combines actuator and cantilever optimization within a unified finite element framework, validated against experimental data published in the literature for similar piezo-actuated sensors using materials with inferior biocompatibility compared with the novel UNCD. The dual-domain simulation strategy offers accurate prediction of key performance metrics, establishing a robust and scalable path for next-generation MEMS biosensors. Full article

We report studies of multifunctional, nanostructured diamond composites that were fabricated using chemical vapor deposition (CVD) techniques. Grain sizes from micrometer, to submicron, nano, and ultrananocrystalline diamond (UNCD) were controlled by varying CH₄, hydrogen, and argon gas concentrations during the syntheses. Scanning electron microscopy (SEM) and Raman scattering spectroscopy were used to investigate the morphologies, composites, and crystallinities of the films. Four multifunctional sensor prototypes were designed, fabricated, and tested, based on the four diamond materials of different grain sizes. The responses of the four prototypes to either pollution gas or UV light illumination were systematically investigated at different operating temperatures. Experimental data indicated the obtained UNCD composite from the low-cost simple CVD fabrication technique appeared to have very good sensitivities when exposed to low concentrations of H₂ or NH₃ gas with a decent response and fast recovery time. Furthermore, highly induced photocurrents from both microdiamond- and UNCD-based prototypes to deep UV illumination were also demonstrated, with responsivities up to 2750 mA/W and 550 mA/W at 250 nm wavelength, respectively. Overall, the fabricated UNCD prototypes displayed a good balance in performance for multifunctional sensor applications in terms of responsivity, stability, and repeatability. Full article

This article shows the results of experiments to grow Nitrogen incorporated ultrananocrystalline diamond (N-UNCD) films on commercial natural graphite (NG)/Cu anodes by hot chemical vapor deposition (HFCVD) using a gas mixture of Ar/CH₄/N₂/H₂. The experiments focused on studying the effect of the pressure in the HFCVD chamber, filament-substrate distance, and temperature of the substrate. It was found that a substrate distance of 3.0 cm and a substrate temperature of 575 C were optimal to grow N-UNCD film on the graphite surface as determined by Raman spectroscopy, SEM, and TEM imaging. XPS analysis shows N incorporation through the film. Subsequently, the substrate surface temperature was increased using a heater, while keeping the substrate-filament distance constant at 3.0 cm. In this case, Raman spectra and SEM images of the substrate surface showed a major composition of graphite in the film as the substrate-surface temperature increased. Finally, the process pressure was increased to 10 Torr where it was seen that the growth of N-UNCD film occurred at 2.0 cm at a substrate temperature of 675 C. These results suggest that as the process pressure increases a smaller substrate-filament distance and consequently a higher substrate surface temperature can still enable the N-UNCD film growth by HFCVD. This effect is explained by a mean free path analysis of the main precursors H₂ and CH₃ molecules traveling from the filament to the surface of the substrate The potential impact of the process developed to grow electrically conductive N-UNCD films using the relatively low-cost HFCVD process is that this process can be used to grow N-UNCD films on commercial NG/Cu anodes for Li-ion batteries (LIBs), to enable longer stable capacity energy vs. charge/discharge cycles. Full article

Implant therapy using osseointegratable titanium (Ti) dental implants has revolutionized clinical dental practice and has shown a high rate of success. However, because a metallic implant is in contact with body tissues and fluids in vivo, ions/particles can be released into the biological milieu as a result of corrosion or biotribocorrosion. Ultrananocrystalline diamond (UNCD) coatings possess a synergistic combination of mechanical, tribological, and chemical properties, which makes UNCD highly biocompatible. In addition, because the UNCD coating is made of carbon (C), a component of human DNA, cells, and molecules, it is potentially a highly biocompatible coating for medical implant devices. The aim of the present research was to evaluate tissue response to UNCD-coated titanium micro-implants using a murine model designed to evaluate biocompatibility. Non-coated (n = 10) and UNCD-coated (n = 10) orthodontic Ti micro-implants were placed in the hematopoietic bone marrow of the tibia of male Wistar rats. The animals were euthanized 30 days post implantation. The tibiae were resected, and ground histologic sections were obtained and stained with toluidine blue. Histologically, both groups showed lamellar bone tissue in contact with the implants (osseointegration). No inflammatory or multinucleated giant cells were observed. Histomorphometric evaluation showed no statistically significant differences in the percentage of BIC between groups (C: 53.40 ± 13% vs. UNCD: 58.82 ± 9%, p > 0.05). UNCD showed good biocompatibility properties. Although the percentage of BIC (osseointegration) was similar in UNCD-coated and control Ti micro-implants, the documented tribological properties of UNCD make it a superior implant coating material. Given the current surge in the use of nano-coatings, nanofilms, and nanostructured surfaces to enhance the biocompatibility of biomedical implants, the results of the present study contribute valuable data for the manufacture of UNCD coatings as a new generation of superior dental implants. Full article

Research and development have been performed to investigate the effect of total pressure and microwave power on the electrical conductivity of nitrogen (N) atoms’ grain boundaries incorporated ultrananocrystalline diamond (N-UNCD) films grown by microwave plasma chemical vapor deposition (MPCVD). Insertion of N atoms into the UNCD film’s grain boundaries induces N atoms chemical reaction with C-atoms dangling bonds, resulting in release of electrons, which induce electrical conductivity. Four-point probe electrical measurements show that the highest electrically conductive N-UNCD films, produced until now, exhibit electrical resistivity of ~1 Ohm.cm, which is orders of magnitude lower than the ≥106 Ohm.cm for undoped ultrananocrystalline diamond (UNCD) films. X-ray diffraction analysis and Raman spectroscopy revealed that the growth of the N-UNCD films by MPCVD do not produce graphite phase but only crystalline nanodiamond grains. X-ray photoelectron spectroscopy (XPS) analysis confirmed the presence of nitrogen (N) in the N-UNCD films and the high conductivity (no electrical charging is observed during XPS analysis) shown in electrical measurements. Full article

With the advances in nanofabrication technology, horizontally aligned and well-defined nitrogen-doped ultrananocrystalline diamond nanostripes can be fabricated with widths in the order of tens of nanometers. The study of the size-dependent electron transport properties of these nanostructures is crucial to novel electronic and electrochemical applications. In this paper, 100 nm thick n-type ultrananocrystalline diamond thin films were synthesized by microwave plasma-enhanced chemical vapor deposition method with 5% N₂ gas in the plasma during the growth process. Then the nanostripes were fabricated using standard electron beam lithography and reactive ion etching techniques. The electrical transport properties of the free-standing single nanostripes of different widths from 75 to 150 nm and lengths from 1 to 128 μm were investigated. The study showed that the electrical resistivity of the n-type ultrananocrystalline diamond nanostripes increased dramatically with the decrease in the nanostripe width. The nanostripe resistivity was nearly doubted when the width was reduced from 150 nm to 75 nm. The size-dependent variability in conductivity could originate from the imposed diffusive scattering of the nanostripe surfaces which had a further compounding effect to reinforce the grain boundary scattering. Full article

This paper describes research focused on investigating the effect of hydrogen (H) atom insertion into the grain boundaries of polycrystalline diamond (PCD) films. This is required in order to understand the key morphological, chemical, physical, and electronic properties of the films. The PCD films were grown using the hot filament chemical vapor deposition (HFCVD) process, with flowing Ar gas mixed with CH₄ and H₂ gases to control film growth into microcrystalline diamond (MCD, 0.5–3 µm grain sizes), nanocrystalline diamond (NCD, 10–500 nm grain sizes), and ultrananocrystalline diamond (UNCD, 2–5 nm grain sizes) films depending on the Ar/CH₄/H₂ flow ratios. This study focused on measuring the H atom concentration of the PCD films to determine the effect on the properties indicated above. A simple model is presented, including a hypothesis that the two dangling bonds per unit cell of C atoms serve as the site of hydrogen incorporation. This correlates well with the observed concentration of H atoms in the films. Dangling bonds which are not passivated by hydrogen are postulated to form surface structures which include C double bonds. The Raman peak from these surface structures are the same as observed for transpolyacetyline (TPA). The data reveal that the concentration of H atoms at the grain boundaries is around 1.5 × 10¹⁵ atoms/cm² regardless of grain size. Electrical current measurements, using a conductive atomic force microscopy (CAFM) technique, were performed using an MCD film, showing that the current is concentrated at the grain boundaries. Ultraviolet photo electron spectroscopy (UPS) confirmed that all the PCD films exhibited a metallic behavior. This is to be expected if the nature of grain boundaries is the same regardless of grain size. Full article

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The boron or nitrogen doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure-based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect-based devices, biological applications and biosensors, and nitrogen-vacancy color center-based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and the future outlook in this area. Full article

Plasma probes are simple and inexpensive diagnostic tools for fast measurements of relevant plasma parameters. While in earlier times being employed mainly in relatively cold laboratory plasmas, plasma probes are now routinely used even in toroidal magnetic fusion experiments, albeit only in the edge region, i.e., the so-called scrape-off layer (SOL), where temperature and density of the plasma are lower. To further avoid overheating and other damages, in medium-size tokamak (MST) probes are inserted only momentarily by probe manipulators, with usually no more than a 0.1 s per insertion during an average MST discharge of a few seconds. However, in such hot and high-density plasmas, their usage is limited due to the strong particle fluxes onto the probes and their casing which can damage the probes by sputtering and heating and by possible chemical reactions between plasma particles and the probe material. In an attempt to make probes more resilient against these detrimental effects, we tested two graphite probe heads (i.e., probe casings with probes inserted) coated with a layer of electrically isolating ultra-nano-crystalline diamond (UNCD) in the edge plasma region of the Experimental Advanced Superconducting Tokamak (EAST) in Hefei, People’s Republic of China. The probe heads, equipped with various graphite probe pins, were inserted frequently even into the deep SOL up to a distance of 15 mm inside the last closed flux surface (LCFS) in low- and high-confinement regimes (L-mode and H-mode). Here, we concentrate on results most relevant for the ability to protect the graphite probe casings by UNCD against harmful effects from the plasma. We found that the UNCD coating also prevented almost completely the sputtering of graphite from the probe casings and thereby the subsequent risk of re-deposition on the boron nitride isolations between probe pins and probe casings by a layer of conductive graphite. After numerous insertions into the SOL, first signs of detachment of the UNCD layer were noticed. Full article

Hard X-ray photoemission spectroscopy (HAXPES) was employed for the structural evaluation of ultrananocrystalline diamond/amorphous carbon (UNCD/a-C) composite films deposited on cemented carbide substrates, at substrate temperatures up to 550 °C by coaxial arc plasma deposition. The results were compared with those of soft X-ray photoemission spectroscopy (SXPES). Since nanocrystalline diamond grains are easily destroyed by argon ion bombardment, the structural evaluation of UNCD/a-C films, without the argon ion bombardment, is preferable for precise evaluation. For samples that were preserved in a vacuum box after film preparation, the sp³ fraction estimated from HAXPES is in good agreement with that of SXPES. The substrate temperature dependencies also exhibited good correspondence with that of hardness and Young’s modulus of the films. On the other hand, the sp³ fraction estimated from SXPES for samples that were not preserved in the vacuum box had an apparent deviation from those of HAXPES. Since it is possible for HAXPES to precisely estimate the sp³ fraction without the ion bombardment treatment, HAXPES is a feasible method for UNCD/a-C films, comprising nanocrystalline diamond grains. Full article

The friction and wear behavior of materials are not intrinsic properties, but extrinsic properties; in other words, they can drastically vary depending on test and environmental conditions. In ambient air, humidity is one such extrinsic parameter. This paper reviews the effects of humidity on macro- and nano-scale friction and wear of various types of materials. The materials included in this review are graphite and graphene, diamond-like carbon (DLC) films, ultrananocrystalline diamond (UNCD), transition metal dichalcogenides (TMDs), hexagonal boron nitride (h-BN), boric acid, silicon, silicon oxide, silicates, advanced ceramics, and metals. Details of underlying mechanisms governing friction and wear behaviors vary depending on materials and humidity; nonetheless, a comparison of various material cases revealed an overarching trend. Tribochemical reactions between the tribo-materials and the adsorbed water molecules play significant roles; such reactions can occur at defect sites in the case of two-dimensionally layered materials and carbon-based materials, or even on low energy surfaces in the case of metals and oxide materials. It is extremely important to consider the effects of adsorbed water layer thickness and structure for a full understanding of tribological properties of materials in ambient air. Full article

Unique functional materials provide a platform as scaffolds for cell/tissue regeneration. Investigation of cell-materials’ chemical and biological interactions will enable the application of more functional materials in the area of bioengineering, which provides a pathway to the novel treatment for patients who suffer from tissue/organ damage and face the limitation of donation sources. Many studies have been made into tissue/organ regeneration. Development of new substrate materials as platforms for cell/tissue regeneration is a key research area. Studies discussed in this paper focus on the investigation of novel ultrananocrystalline diamond (UNCD) films as substrate/scaffold materials for developmental biology. Specially designed quartz dishes have been coated with different types of UNCD films and cells were subsequently seeded on those films. Results showed the cells’ growth on UNCD-coated culture dishes are similar to cell culture dishes with little retardation, indicating that UNCD films have no or little inhibition on cell proliferation and are potentially appealing as substrate/scaffold materials. The mechanisms of cell adhesion on UNCD surfaces are proposed based on the experimental results. The comparisons of cell cultures on diamond-powder-seeded culture dishes and on UNCD-coated dishes with matrix-assisted laser desorption/ionization—time-of-flight mass spectroscopy (MALDI-TOF MS) and X-ray photoelectron spectroscopy (XPS) analyses provided valuable data to support the mechanisms proposed to explain the adhesion and proliferation of cells on the surface of the UNCD platform. Full article