Search Results (36)

Bismuth–telluride-based alloys are excellent thermoelectric materials for Peltier modules and thermoelectric generators (TEGs). Owing to the emergence of the Internet of Things (IoT), the demand for sensors has increased considerably and self-power supplies to sensors using TEGs are garnering attention. To apply TEGs to IoT sensors, the thermoelectric materials used must be sufficiently small and thin while exhibiting high thermoelectric performance. In this study, Bi_0.5Sb_1.5Te₃ thin films were prepared using a pressure-gradient sputtering system. The obtained films exhibit a nanocrystalline structure with a significantly smooth surface and no preferred crystal orientation. Because the Bi_0.5Sb_1.5Te₃ thin films exhibit a high Seebeck coefficient and low thermal conductivity, the in-plane dimensionless figure of merit is 0.98, which is one of the highest values reported for thermoelectric materials measured near 300 K. Furthermore, the phonon mean-free path is 0.19 nm, as estimated using the 3ω method and nanoindentation. This value is significantly smaller than the average crystallite size of the thin film, thus indicating that phonon scattering occurs more frequently via ternary-alloy scattering inside the crystallites than via boundary scattering at the crystallite boundaries. The results of this study can advance thin-film TEGs as a source of self-sustaining power for IoT systems. Full article

Thin-film solar cells (TFSCs) represent a promising frontier in renewable energy technologies due to their potential for cost reduction, material efficiency, and adaptability. This literature review examines the key materials and advancements that make up TFSC technologies, with a focus on Cu(In,Ga)Se₂ (CIGS), cadmium telluride (CdTe), and Cu₂ZnSnS₄ (CZTS) and its sulfo-selenide counterpart Cu₂ZnSn(S,Se)₄ (CZTSSe). Each material’s unique properties—including tuneable bandgaps, high absorption coefficients, and low-cost scalability—make them viable candidates for a wide range of applications, from building-integrated photovoltaics (BIPV) to portable energy solutions. This review explores recent progress in the enhancement of power conversion efficiency (PCE), particularly through bandgap engineering, alkali metal doping, and interface optimization. Key innovations such as silver (Ag) alloying in CIGS, selenium (Se) alloying in CdTe, and sulfur (S) to Se ratio optimization in CZTSSe have driven PCE improvements and expanded the range of practical uses. Additionally, the adaptability of TFSCs for roll-to-roll manufacturing on flexible substrates has further cemented their role in advancing renewable energy adoption. Challenges remain, including environmental concerns, but ongoing research addresses these limitations, paving the way for TFSCs to become a crucial technology for transitioning to sustainable energy systems. Full article

In this work, we developed nanostructured Bi₂Te₃ and Sb₂Te₃ thin films by thermal co-evaporation of their alloys with corresponding pure elements (Bi, Sb, and Te). The films were fabricated on borosilicate glass at different substrate temperatures and deposition rates. At 300 °C, enhanced thermoelectric performance was demonstrated for n-type Bi₂Te₃:Bi and p-type Sb₂Te₃:Te, with Seebeck coefficients of 195 µV K⁻¹ and 178 μV K⁻¹, along with electrical conductivities of 4.6 × 10⁴ (Ω m)⁻¹ and 6.9 × 10⁴ (Ω m)⁻¹, resulting in maximum power factor values of 1.75 mW K⁻² m⁻¹ and 2.19 mW K⁻² m⁻¹, respectively. These values are found to be higher than some reported works in the literature, highlighting the advantage of not introducing additional elements to the system (such as extra doping, which induces complexity to the system). The structural properties, film morphology, and chemical composition of the optimized films were investigated using X-ray diffraction (XRD) and scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS). The films were found to be polycrystalline with preferred (0 0 6) and (0 1 5) orientations for Bi₂Te₃ and Sb₂Te₃ films, respectively, and stable rhombohedral phases. Additionally, a ring-shaped p-n thermoelectric device for localized heating/cooling was developed and a temperature difference of ~7 °C between the hot and cold zones was obtained using 4.8 mA of current (J = 0.068 mA/mm²). Full article

Infrared (IR) sensors are widely used in various applications due to their ability to detect infrared radiation. Currently, infrared detector technology is in its third generation and faces enormous challenges. IR radiation propagation is categorized into distinct transmission windows with the most intriguing aspects of thermal imaging being mid-wave infrared (MWIR) and long-wave infrared (LWIR). Infrared detectors for thermal imaging have many uses in industrial applications, security, search and rescue, surveillance, medical, research, meteorology, climatology, and astronomy. Presently, high-performance infrared imaging technology mostly relies on epitaxially grown structures of the small-bandgap bulk alloy mercury–cadmium–telluride (MCT), indium antimonide (InSb), and GaAs-based quantum well infrared photodetectors (QWIPs), contingent upon the application and wavelength range. Nanostructures and nanomaterials exhibiting appropriate electrical and mechanical properties including two-dimensional materials, graphene, quantum dots (QDs), quantum dot in well (DWELL), and colloidal quantum dot (CQD) will significantly enhance the electronic characteristics of infrared photodetectors, transition metal dichalcogenides, and metal oxides, which are garnering heightened interest. The present manuscript gives an overview of IR sensors, their types, materials commonly used in them, and examples of related applications. Finally, a summary of the manuscript and an outlook on prospects are given. Full article

Gold compositional studies have been advocated to resolve genetic relationships between alluvial and in situ occurrences based on the assumption that the P-T-X conditions at the sites of mineral deposition are reflected in common compositional signatures of gold. Here, we explore two refinements to a simple ‘same or different’ approach, namely (i) in situ gold sources at different localities may correspond to multiple stages of mineralization and, therefore, different gold grade, and (ii) any duplication of gold signatures between localities requires fluid conduits compatible with the prevailing structural framework. The high-grade gold paragenetic stage at the Cononish Mine, Scotland, is characterized by relatively low Ag alloy associated with Ag-Au and Ag tellurides. This signature is replicated in the inclusion signature of alluvial gold from the adjacent drainage and is also present in two other drainages for which there are no known in situ sources. There is a strong correlation between the spatial extent of this signature and the fault linkage zone, but outside this zone, gold exhibits other compositional signatures. The study shows how structural considerations provide an independent and robust framework to evaluate genetic relationships suggested by compositional studies of alluvial gold in areas where the source location and economic potential are unknown. Full article

Bi₂Te₃-based alloys are representatively commercialized thermoelectric materials for refrigeration and power generation. Refrigeration mainly utilizes thermoelectric properties near room temperature, while the power generation temperature is relatively high. However, it is difficult for bismuth telluride to maintain good thermoelectric properties throughout the entire temperature range of 300–500 K. Herein, a series of Bi_xSb_2−xTe₃ alloys with different Bi contents were prepared by a simple preparation method and systematically investigated, and their best application temperature range was found. The Bi content can modulate carrier concentration and band gap, and the maximum dimensionless figure of merit (ZT) value of Bi_xSb_2−xTe₃ can be achieved in the corresponding application temperature range. The maximum ZT of Bi_0.3Sb_1.7Te₃ with a Bi content equal to 0.3 reaches 1.14 at 400 K, and the average ZT is 1.06 in the range of 300–500 K, which is suitable for both power generation and refrigeration. Therefore, power generation technologies with higher application temperatures should be selected from Bi_xSb_2−xTe₃ materials with Bi content less than 0.3, and refrigeration technologies with lower application temperatures should be selected with Bi content greater than 0.3. This work provides experimental guidance for finding the composition of Bi₂Te₃-based alloys in scientific research and practical applications. Full article

Variations in the recovery of platinum group metals (PGMs) are often attributed to mineralogical and other natural ore-type variations. To increase the recovery of PGMs by the flotation process, a comprehensive understanding of gangue and valuable minerals is essential for optimising the extraction and processing of metals. Recoveries may be improved if the questions of how, where, and why losses occur can be answered with a certain degree of confidence. A requirement is the availability of statistically reliable mineralogical data. The PGMs of MG-1–4 chromite tailings dumps of the western limb of the Bushveld complex (BC) were studied in detail to unravel the PGMs and the nature of the platinum group minerals in the sample. Characterisation of the chromite tailings via deportment analysis revealed that the sample contained a significant amount of 3E PGM + Au (Pt, Pd, Ru, and Au) and was concentrated in the -25 µm fraction. The results of automated mineralogical analysis showed that the sample was composed of the PGE-sulphides group, comprising 63.6 vol%, PGE-sulfarsenides 10.4 vol%, PGE-arsenides 1.3 vol%, PGE-bismuth tellurides 3.3 vol%, PGMs-alloy 4.1 vol%, and Laurite comprising 17.3 vol% of the total PGE population. The sample was composed of 66.5 vol% of liberated PGMs, 0.2 vol% attached to liberated BMS, 27.3 vol% of PGMs attached to or locked within silicate or oxide gangue composite particles, 0.2 vol% of PGMs associated with BMS attached to silicate or oxide gangue particles, and a low proportion (5.8 vol%) of PGMs reported being locked within gangue or oxide particles. The majority of PGM grains observed were reported in the fast-floating category (64.4 vol%), 27.6 vol% in the slow-floating 1 category, 2.2 vol% in the slow-floating 2 category, and 5.8 vol% to the non-floating category. The results of the study revealed that the PGMs of MG 1–4 chromite tailings were liberated; however, the low liberation index (<0.2) suggested that a significant portion of PGMs remained trapped within gangue, hindering their recovery. This highlights the need for effective comminution (crushing and grinding) to achieve better liberation. The sample contained fine particles that were more prone to being lost in the tailings and to lowering recovery due to the slimes coating valuable minerals. The recovery of the PGMs from this complex’s polymetallic bodies of low-grade and complex mineralogy will be insufficient with traditional methods and thus innovation is needed. Innovation like advanced comminution, novel flotation equipment or reagents, selective leaching and bioprocessing can overcome these challenges. Full article

Bismuth telluride (Bi₂Te₃)-based alloys have been extensively employed in energy harvesting and refrigeration applications for decades. However, commercially produced Bi₂Te₃-based alloys using the zone-melting (ZM) technique often encounter challenges such as insufficient mechanical properties and susceptibility to cracking, particularly in n-type Bi₂Te₃-based alloys, which severely limit the application scenarios for bismuth telluride devices. In this work, we seek to enhance the mechanical properties of n-type Bi₂Te_2.7Se_0.3 alloys while preserving their thermoelectrical performance by a mixed mechanism of grain refinement and the TiN composite phase-introduced pinning effect. These nanoscale processes, coupled with the addition of TiN, result in a reduction in grain size. The pinning effects of nano-TiN contribute to increased resistance to crack propagation. Finally, the TiN-dispersed Bi₂Te_2.7Se_0.3 samples demonstrate increased hardness, bending strength and compressive strength, reaching 0.98 GPa, 36.3 MPa and 74 MPa. When compared to the ZM ingots, those represent increments of 181%, 60% and 67%, respectively. Moreover, the thermoelectric performance of the TiN-dispersed Bi₂Te_2.7Se_0.3 samples is identical to the ZM ingots. The samples exhibit a peak dimensionless figure of merit (ZT) value of 0.957 at 375 K, with an average ZT value of 0.89 within the 325–450 K temperature range. This work has significantly enhanced mechanical properties, increasing the adaptability and reliability of bismuth telluride devices for various applications, and the multi-effect modulation of mechanical properties demonstrated in this study can be applied to other thermoelectric material systems. Full article

Hot pressing represents a promising consolidation technique for ball-milled bismuth telluride alloys, yet deep investigations are needed to understand its effect on the thermoelectric properties. This paper studies the effect of hot-pressing parameters (temperature and pressure) on the thermoelectric properties of the n-type Gr-Bi₂Te_2.55Se_0.45 nanocomposite. Ultra-high pressure, up to 1.5 GPa, is considered for the first time for consolidating Bi₂(Te,Se)₃ alloys. Results from this study show that increasing the temperature leads to changes in chemical composition and causes noticeable grain growth. On the contrary, increasing pressure mainly causes improvements in densification. Overall, increments in these two parameters improve the ZT values, with the temperature parameter having a higher influence. The highest ZT of 0.69 at 160 °C was obtained for the sample hot-pressed at 350 °C and 1 GPa for 5 min, which is indeed an excellent and competitive value when compared with results reported for this n-type Bi₂Te_2.55Se_0.45 composition. Full article

P-type Bi_0.3Sb_1.7Te₃ polycrystalline pellets were fabricated using different methods: melting and mechanical alloying, followed by hot-press sintering. The effect of starting powder particle size on the thermoelectric properties was investigated in samples prepared using powders of different particle sizes (with micro- and/or nano-scale dimensions). A peak ZT (350 K) of ~1.13 was recorded for hot-pressed samples prepared from mechanical alloyed powder. Moreover, hot-pressed samples prepared from ≤45 μm powder exhibited similar ZT (~1.1). These high ZT values are attributed both to the presence of high-density grain boundaries, which reduced the lattice thermal conductivity, as well as the formation of antisite defects during milling and grinding, which resulted in lower carrier concentrations and higher Seebeck coefficient values. In addition, Bi_0.3Sb_1.7Te₃ bulk nanocomposites were fabricated in an attempt to further reduce the lattice thermal conductivity. Surprisingly, however, the lattice thermal conductivity showed an unexpected increasing trend in nanocomposite samples. This surprising observation can be attributed to a possible overestimation of the lattice thermal conductivity component by using the conventional Wiedemann–Franz law to estimate the electronic thermal conductivity component, which is known to occur in nanocomposite materials with significant grain boundary electrical resistance. Full article

Chalcogenide alloys of As₂Se₃-Ag₂Te-GeTe were synthesized using the melt-quenching technique. By the visual and XRD analyses, the state of obtaining alloys was proven (glass, crystalline, glass + crystalline), and the glass formation region in the system was established. The thermal characteristics of some samples were determined—temperatures of glass transition (T_g); crystallization (T_cr); and melting (T_m). The basic physicochemical parameters, such as density (d) and Vickers microhardness (HV), were measured. Compactness (C), as well as some thermomechanical characteristics, such as module of elasticity (E), volume (V_h), and formation energy (E_h) of micro-voids, were calculated, and the influence of the composition on these characteristics was investigated. The addition of silver telluride resulted in a decrease in T_g and HV values and an increase in d and V_h values. No thermochemical effects of crystallization or melting were detected in some of the alloys. The obtained results were in agreement with the available literature data for similar systems. Full article

Commercial Peltier cooling devices and thermoelectric generators mostly use bismuth telluride-based materials, specifically its alloys with Sb₂Te₃ for the p-type legs and its alloys with Bi₂Se₃ for the n-type legs. If the p-type materials perform with zT well above the unity around room temperature, the n-type counterpart is lacking efficiency in this temperature range, and has the disadvantage of containing selenium. Indeed, despite the fact that selenium is not environmentally benign and that its handling requires precautions, the use of selenium does not facilitate the optimization of thermoelectric performance at or around room temperature, as the presence of selenium results in a larger band gap. In this study, we investigate the feasibility of a selenium-free n-type (Bi, Sb)₂Te₃ using a simple two-step process: mechanical alloying synthesis followed by spark plasma sintering. All the members of the solid solution Bi_2−xSb_xTe₃ with x < 1 are n-type materials, with zTs between 0.35 and 0.6. The zT is maximized at lower temperatures with an increasing Sb content, which is proof that the band gap is reduced accordingly. We also show here that an edge-free sintering process considerably improves thermoelectric performance. Full article

Tellurium is used in cadmium tellurium-based solar cells. Mercury cadmium telluride is used as a sensing material for thermal imaging devices. High-purity tellurium is used in alloys for electronic applications. It is one of the important raw materials for solar energy applications. It is used as an alloying element in the production of low-carbon steel and copper alloys. Tellurium catalysts are used chiefly for the oxidation of organic compounds and as vulcanizing/accelerating agents in the processing of rubber compounds. Even though several researchers tried to recover tellurium from different raw materials, there is no attempt to develop a process flow sheet to recover tellurium from waste anode slime having a high tellurium concentration. In this study, optimum conditions were developed to recover Te and Cu from anode slime with the composition Cu: 31.8%, Te: 24.7%, and As: 0.96%. The unit operations involved are leaching, purification, and electro winning. The optimum conditions for producing Te at a recovery of 90% are found to be roasting of anode slime at 450 °C without the addition of soda ash followed by leaching in 1 M NaOH at 10% pulp density for 2 h. The purity of Te metal achieved was up to 99.99%, which could provide a sustainable energy future. The major impurities of the tellurium are observed to be in the order: Se > Sb > As > Cu. Full article

Neuromorphic computing, reconfigurable optical metamaterials that are operational over a wide spectral range, holographic and nonvolatile displays of extremely high resolution, integrated smart photonics, and many other applications need next-generation phase-change materials (PCMs) with better energy efficiency and wider temperature and spectral ranges to increase reliability compared to current flagship PCMs, such as Ge₂Sb₂Te₅ or doped Sb₂Te. Gallium tellurides are favorable compounds to achieve the necessary requirements because of their higher melting and crystallization temperatures, combined with low switching power and fast switching rate. Ga₂Te₃ and non-stoichiometric alloys appear to be atypical PCMs; they are characterized by regular tetrahedral structures and the absence of metavalent bonding. The sp³ gallium hybridization in cubic and amorphous Ga₂Te₃ is also different from conventional p-bonding in flagship PCMs, raising questions about its phase-change mechanism. Furthermore, gallium tellurides exhibit a number of unexpected and highly unusual phenomena, such as nanotectonic compression and viscosity anomalies just above their melting points. Using high-energy X-ray diffraction, supported by first-principles simulations, we will elucidate the atomic structure of amorphous Ga₂Te₅ PLD films, compare it with the crystal structure of tetragonal gallium pentatelluride, and investigate the electrical, optical, and thermal properties of these two materials to assess their potential for memory applications, among others. Full article

The Ildeus mafic–ultramafic complex represents plutonic roots of a Triassic magmatic arc tectonically emplaced into the thickened uppermost crust beneath the Mesozoic Stanovoy collided margin. The mafic–ultramafic complex cumulates host Ni-Co-Cu-Pt-Ag-Au sulfide-native metal-alloy mineralization produced through magmatic differentiation of subduction-related primary mafic melt. This melt was sourced in the metal-rich sub-arc mantle wedge hybridized by reduced high-temperature H-S-Cl fluids and slab/sediment-derived siliceous melts carrying significant amounts of Pt, W, Au, Ag, Cu and Zn. Plutonic rocks experienced a pervasive later-stage metasomatic upgrade of the primary sulfide–native metal–alloy assemblage in the presence of oxidized hydrothermal fluid enriched in sulfate and chlorine. The new metasomatic assemblage formed in a shallow epithermal environment in the collided crust includes native gold, Ag-Au, Cu-Ag and Cu-Ag-Au alloys, heazlewoodite, digenite, chalcocite, cassiterite, galena, sphalerite, acanthite, composite Cu-Zn-Pb-Fe sulfides, Sb-As-Se sulfosalts and Pb-Ag tellurides. A two-stage model for magmatic–hydrothermal transport of some siderophile (W, Pt, Au) and chalcophile (Cu, Zn, Ag) metals in subduction–collision environments is proposed. Full article