Search Results (904)

The rising volume of sludge production poses significant environmental threats. Sludge has a high moisture content (MC), which increases its disposal and transport expenses. On the other hand, sludge has low dewaterability due to its high concentration of soluble organic compounds. To reduce sludge production, understanding and improving preconditioning and mechanical dewatering are crucial for breakthroughs in advanced sludge dewatering. The sludge samples used in this analysis were obtained from the Sarabium municipal wastewater treatment plant, with a moisture content of 97% and a specific filtration resistance (SRF) of 9.15463 × 10¹⁵ m/kg. Sludge dewatering was enhanced by treating the samples chemically with ferric chloride, aluminum sulfate, Moringa olifera, and cationic polyacrylamide CPAM and physically with wood chips, slag, rice husk, and wheat straw. The experiments examined the sludge’s initial characterization (specific resistance to filtration (SRF) and time to filtrate (TTF)). To verify the structural characteristics (density), elemental composition, and the presence of various functional groups, a characterization investigation was conducted using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and energy-dispersive X-ray spectroscopy (EDS). The results showed that chemical conditioning with ferric chloride is better than aluminum sulfate and Moringa. Wood chips also provide better results for physical conditioning than rice husk, wheat straw, and slag. The reaction occurred at the carbonyl group, where FTIR showed more activated sites during SEM analysis, as evidenced by the FTIR results. Still, when CPAM was added to conditioned sludge, there was no difference in sludge dewatering performance, and the activated sites remained unchanged. Hence, this research found that mechanical sludge dewatering was improved by conditioning with ferric chloride (pH of 6 and dose of 0.12 g/g of dry solid) and wood chips (dose of 1.5 g/g of dry solid), which reduced sludge volume after dewatering by 82.5% under low pressure, which in turn minimizes transportation, energy, and handling costs. This study supports SDG 3 and SDG 6 by improving sludge dewatering efficiency and promoting sustainable wastewater management using natural wood chips. Full article

Growing pressures on water resources, exacerbated by climate change, resource depletion, and population growth, underline the need for sustainable and energy-efficient wastewater management. Wastewater treatment plants (WWTPs) are among the most energy-intensive elements of the Integrated Water Service, and their environmental performance depends on infrastructure design, resource availability, and treatment configuration. Improving resource efficiency while reducing energy demand and environmental impacts is therefore a priority for water utilities seeking innovative decision-support tools. Within the national project “WATERGY—Energy Efficiency of the Integrated Water Service”, this study proposes a life-cycle-based framework to assess the sustainability of technological interventions in WWTPs. A comparative gate-to-grave Life Cycle Assessment (LCA) was applied to the municipal WWTP of Potenza (Southern Italy). Three sludge End-of-Life Scenarios were assessed: the current landfill-based configuration, an enhanced oxygenation–nitrification setup, and anaerobic digestion with biogas-based cogeneration. Compared to the current scenario, anaerobic digestion with cogeneration reduces Global Warming Potential by 17% and decreases freshwater ecotoxicity by approximately 30%. Compost production shows the highest reduction in ecotoxicity (−51%) but increases fossil resource depletion and acidification due to higher energy demand. Overall, energy recovery pathways, particularly anaerobic digestion with cogeneration, provide the most balanced environmental benefits, supporting more sustainable WWTP operation within the Integrated Water Service. Full article

Nitrate in Baiyangdian Lake is directly linked to the sustainability of watershed ecological functions, acting as a key priority for regional ecological protection. Subsequent to the completion of a series of ecological restoration projects, its sources have undergone inevitable shifts, rendering the original pollution control framework incompatible with the new context. Thus, accurate identification of nitrate sources and their seasonal variation characteristics constitutes a core prerequisite for enhancing the targeting of pollution management. This study integrated dual stable isotopes (δ¹⁵N-NO₃⁻ and δ¹⁸O-NO₃⁻) in water and potential source samples, along with hydrochemical data, and applied the Bayesian stable isotope mixing model (MixSIAR) to elucidate the sources of NO₃⁻ in Baiyangdian Lake. The results indicated that denitrification exerted a weak influence on the isotopic composition of NO₃⁻ in Baiyangdian Lake. Plots of the NO₃⁻/Cl⁻ versus Cl⁻ ratios for water samples and δ¹⁵N-NO₃⁻ versus δ¹⁸O-NO₃⁻ ratios for both water samples and potential sources confirmed anthropogenic sources as the primary nitrate contributors. The δ¹⁵N-NO₃⁻ vs. 1/[NO₃⁻] plot revealed that the number of NO₃⁻ sources exceeded two. The MixSIAR model demonstrated that wastewater treatment plant (WWTP) discharge was the dominant source throughout the four seasons, accounting for 49–62% with the highest contribution in winter and the lowest in summer. Soil nitrogen release contributed 19–32%, reaching its annual peak in summer. Sediment release accounted for 11–13%, maintaining a relatively low contribution across all seasons. Chemical fertilizer, manure, and sewage (M&S), and atmospheric deposition each contributed less than 6.5%, with negligible contributions. A significant reduction in the contributions of sediment release and M&S reflected the optimization effect of long-term regional ecological restoration efforts. WWTPs point source discharge and seasonal non-point source input from soil nitrogen collectively constituted the core sources of nitrate in Baiyangdian Lake. These findings provide crucial scientific support for the precise source apportionment and differentiated management of nitrate pollution in the basin. Full article

Sustainable urban water system (UWS) management is vital for climate-resilient, resource-efficient cities. This study presents the first comprehensive life cycle assessment (LCA) of Seoul Metropolitan City (SMC)’s UWS, encompassing water abstraction, treatment, distribution, wastewater collection and treatment, and sludge management. Nine midpoint impact categories from ReCiPe 2016 (H) were analyzed to identify environmental hotspots and mitigation pathways. Results show that wastewater treatment dominates impacts, contributing 57.3% of global warming potential (GWP; 0.947 kg CO₂-eq per functional unit of 1 m³ of potable water supplied) and 71.1% of freshwater eutrophication (FE; 0.00066 kg P-eq/m³), driven by electricity use, sludge disposal, and direct CH₄/N₂O emissions. Electricity consumption is the leading driver across GWP, terrestrial acidification (TA), and fossil resource scarcity (FRS). Infrastructure construction notably influenced terrestrial ecotoxicity (TET) and human toxicity. Sensitivity analysis showed that SMC’s projected 2030 electricity mix could reduce GWP and FRS by up to 18%. Scenario evaluations revealed that sludge ash utilization in concrete and expanded wastewater reuse improve resource circularity, whereas biogas upgrading, solar generation, and heat recovery significantly lower GWP and FRS. The findings underscore the importance of energy decarbonization, resource recovery, and infrastructure longevity in achieving low-carbon and resource-efficient UWSs. This study offers a transferable framework for guiding sustainability transitions in rapidly urbanizing, energy-transitioning regions. Full article

Microbial fuel cells (MFCs) have attracted increasing attention due to their potential applications in renewable energy generation, waste utilization, and biomass upgrading, offering a promising alternative to traditional fossil fuels. By directly converting carbon-rich wastes into electricity, MFCs provide a unique approach to simultaneously address energy demand and waste management challenges. This review systematically examines the effects of various carbon-rich substrates on MFC performance, including lignocellulosic biomasses, molasses, lipid waste, crude glycerol, and C1 compounds. These substrates, characterized by wide availability, low cost, and high carbon content, have demonstrated considerable potential for efficient bioelectricity generation and resource recovery. Particular emphasis is placed on the roles of microbial community regulation and genetic engineering strategies in enhancing substrate utilization efficiency and power output. Additionally, the application of carbon-rich wastes in electrode fabrication is discussed, highlighting their contributions to improved electrical conductivity, sustainability, and overall system performance. The integration of carbon-rich substrates into MFCs offers promising prospects for alleviating energy shortages, improving wastewater treatment efficiency, and reducing environmental pollution, thereby supporting the development of a circular bioeconomy. Despite existing challenges related to scalability, operational stability, and system cost, MFCs exhibit strong potential for large-scale implementation across diverse industrial sectors. Full article

Wastewater treatment is one of the major challenges in the reuse of water as a natural resource. Cleaning of water depends on analyzing and treating the water for the pollutants that have a significant impact on the quality of the water. Detecting and analyzing the surges of these pollutants well before the recycling process is needed to make intelligent decisions for water cleaning. The dynamic changes in pollutants need constant monitoring and effective planning with appropriate treatment strategies. We propose an edge-computing-based smart framework that captures data from sensors, including ultraviolet, electrochemical, and microfluidic, along with other significant sensor streams. The edge devices send the data from the cluster of sensors to a centralized server that segments anomalies, analyzes the data and suggests the treatment plan that is required, which includes aeration, dosing adjustments, and other treatment plans. A logic layer is designed at the server level to process the real-time data from the sensor clusters and identify the discharge of nutrients, metals, and emerging contaminants in the water that affect the quality. The platform can make decisions on water treatments using its monitoring, prediction, diagnosis, and mitigation measures in a feedback loop. A rule-based Large Language Model (LLM) agent is attached to the server to evaluate data and trigger required actions. A streamlined data pipeline is used to harmonize sensor intervals, flag calibration drift, and store curated features in a local time-series database to run ad hoc analyses even during critical conditions. A user dashboard has also been designed as part of the system to show the recommendations and actions taken. The proposed system acts as an AI-enabled system that makes smart decisions on water treatment, providing an effective cleaning process to improve sustainability. Full article

Wastewater treatment systems retain a significant proportion of microplastics (MPs) derived from domestic and industrial discharges; however, these emerging pollutants are not completely removed and tend to accumulate in the biological sludge generated during the treatment process. In this study, three biological-type wastewater treatment plants (WWTPs) located in Acapulco, Mexico, were analyzed. The concentrations of MPs in the biological sludge ranged from 830 to 9300 particles/L. Using differential scanning calorimetry (DSC), the predominant polymers identified were high-density polyethylene (HDPE), polyethylene terephthalate (PET), and polypropylene (PP). It was estimated that the monthly concentrations of MPs in the sludge could reach up to 5.36 × 10⁹ particles/L, while the annual concentrations could rise to 3.55 × 10¹⁰ particles/L. These findings highlight the urgent need to review and update the regulatory framework related to the use of residual sludge for agricultural purposes, since high loads of MPs and their transfer pose a potential risk to soil quality, ecosystem health, and long-term environmental sustainability. Full article

Sludge management is one of the most costly and technically challenging components of municipal wastewater treatment, highlighting the need for sustainable and low-cost stabilization technologies. This study evaluated a pilot-scale vermifiltration system for municipal sewage sludge stabilization under varying hydraulic and organic loading conditions. Three vermifilter pilots incorporating Eisenia andrei earthworms were operated using lightweight expanded clay aggregate (LECA), high-density polyethylene (HDPE) plastic media, and mineral pumice. The systems were tested at hydraulic loading rates (HLRs) of 150, 300, and 450 L/m²·d. Performance was assessed using chemical oxygen demand (COD), total solids (TS), volatile solids (VS), VS/TS ratio, sludge volume index (SVI), and sludge dewaterability indicators, including specific resistance to filtration (SRF) and time to filtration (TTF). Optimal performance occurred at an HLR of 150 L/m²·d, achieving maximum reductions of 49% in COD, 30% in TS, and 40% in VS, along with an SVI reduction of up to 78%. Increasing HLR significantly reduced treatment efficiency due to shorter retention times and biofilm washout. A regression analysis showed the strongest association between COD removal and organic loading rate (R² = 0.63) under the coupled HLR–OLR conditions tested, while weaker correlations were observed for SVI and VS/TS. Dewaterability improved markedly after vermifiltration, particularly in the LECA-based system. Although filter media type did not significantly affect COD or SVI removal, pumice and plastic media provided greater hydraulic stability at higher loadings. These results demonstrate that vermifiltration is an effective and environmentally sustainable option for municipal sludge stabilization when operated under controlled hydraulic conditions. Full article

Growing pressure on water resources and mineral fertilizer use calls for innovative and resource-efficient agri-food systems. Aquaponics, integrating aquaculture and hydroponics, represents a promising approach for sustainable greenhouse production. This study, aiming to explore alternative water and nutrient sources for greenhouse tomato production without compromising plant adaptability or yield, evaluated the co-cultivation of grape tomato and rainbow trout in a vertical decoupled aquaponic system under controlled greenhouse conditions. Two aquaponic nutrient strategies were tested: unmodified aquaponic water (AP) and complemented aquaponic water (CAP), with conventional hydroponics (HP) as a control, in a Deep Water Culture hydroponic system. Plant performance was assessed through marketable yield and physiological parameters, while system performance was evaluated using combined-biomass Energy Use Efficiency (EUE), Freshwater Use Efficiency (fWUE) and Nitrogen Use Efficiency (NUE), accounting for both plant and fish production. CAP significantly improved tomato yield (9.86 kg m⁻²) compared to AP (2.40 kg m⁻²), although it remained lower than HP (12.14 kg m⁻²). Fresh WUE was comparable between CAP and HP (9.22 vs. 9.24 g L⁻¹), demonstrating effective water reuse. In contrast, EUE and NUE were lower in CAP, reflecting the additional energy demand of the recirculating aquaculture system and nutrient limitations of fish wastewater. These results highlight aquaponics as a water-efficient production system while emphasizing that optimized nutrient management and energy strategies are critical for improving its overall sustainability and performance. Full article

Increasing global water scarcity has intensified the adoption of water reuse as a sustainable strategy, particularly in regions affected by drought and pressure on natural resources. This paper presents a systematic review of the application of Life Cycle Assessment (LCA) in water reuse projects, focusing on research trends, methodological approaches, and opportunities for improvement. A systematic search was conducted in Web of Science, ScienceDirect, and Google Scholar for studies published from 2020 onwards using combinations of the keywords “life cycle assessment”, “LCA”, “water reuse”, “water recycling”, and “wastewater recycling”. Twelve studies were selected from 57 records identified, based on predefined eligibility criteria requiring quantitative LCA of water reuse systems. The results reveal a predominance of European research, reflecting regulatory advances and strong academic engagement in this field. The most frequently assessed impact categories were global warming, eutrophication, human toxicity and ecotoxicity, highlighting the environmental relevance of reuse systems. Energy consumption and water transport were identified as critical hotspots, especially in scenarios involving long distances and fossil-based energy sources. Nevertheless, most studies demonstrate that water reuse is environmentally viable, particularly when renewable energy and optimized logistics are applied. The review also emphasizes the need to better integrate economic and social dimensions and to adapt LCA methodologies to local conditions. Overall, the findings confirm LCA as a robust decision-support tool for sustainable planning and management of water reuse systems. Full article

Constructed wetlands (CWs) are signified as green, self-sustaining systems for wastewater treatment. To date, their conventional designs struggle with slow kinetics and poor removal of refractory pollutants. This review redefines CWs as photo-reactive engineered systems, integrating near-neutral Fenton and photo-Fenton processes and in-situ oxidant generation to overcome diffusion limits, acid dosing, and sludge formation. By coupling catalytic fillers, solar utilization, and plant–microbe–radical (ROS) synergies, the approach enables intensified pollutant degradation while preserving the low-energy nature of CWs. Bibliometric trends indicate a sharp rise in studies linking CWs with advanced oxidation and renewable energy integration, confirming the emergence of a circular treatment paradigm. A decision framework is proposed that aligns material selection, reactor hydrodynamics, and solar light management with sustainability indicators such as energy efficiency, Fe-leach budget, and ROS-to-photon yield. This synthesis bridges environmental biotechnology with solar-driven catalysis, paving the way for next-generation eco-engineered wetlands capable of operating efficiently beyond the classical Fenton constraints. This work introduces the concept of “Constructed Wetlands Beyond the Fenton Limit”, where CWs are reimagined as photo-reactive circular systems that unify catalytic, biological, and solar processes under near-neutral conditions. It provides the first integrated decision matrix and performance metrics connecting catalyst design, ROS efficiency, and circular sustainability that offers a scalable blueprint for real-world hybrid wetland applications. Full article

There is an urgent need to develop sustainable approaches for the remediation of contaminated soil as well as to promote sustainable practices for waste management. Here, we provide the first evaluation of the performance of two types of iron nanoparticles (NA and NH) obtained from olive mill wastewater for the remediation of an acidic multi-contaminated soil, including metal(loid)s, PCBs, and a flame retardant (TCPP). Their efficiency was then compared against that of a commercial nanoscale zero-valent iron (NS) through a one-month microcosm experiment employing two doses of each nanomaterial. The impact of the treatments on key soil physicochemical properties, metal(loid) availability, PCB and TCPP concentrations, and soil phytotoxicity was assessed. All treatments reduced soil acidity. Regarding organic contaminants, bioremediation of TCPP was enhanced by all nanomaterials, particularly NH, whereas NA was the only treatment that significantly reduced PCB concentration under the tested conditions. NS achieved the highest rates of metal(loid) immobilization (63–100%); NH was most beneficial for soil fertility and immobilized As, Ni, and Pb (100, 38, and 53%, respectively), whereas NA was only effective for Pb (21–49%). The low dose of both NA and NH improved the germination index (66 and 61%, respectively), reducing soil phytotoxicity. These results highlight the potential of valorizing olive mill wastewater for soil remediation, thereby contributing to the principles of the Circular Economy. Full article

Recycled wastewater is vital for the circular economy, especially on water-scarce islands. This study explored the presence of Carbapenem-Resistant Enterobacterales and other emerging pathogens in irrigation water on four Canarian Islands, applying a One Health perspective. Using membrane filtration and MALDI-TOF mass spectrometry, 69 bacterial isolates were identified. The findings revealed that 78% were Gram-negative bacilli like Pseudomonas aeruginosa, Acinetobacter spp., Enterobacteriaceae, etc., while 22% were Gram-positive bacteria, including Enterococcus spp. The main mechanisms of carbapenem resistance in Pseudomonas spp. and Acinetobacter spp. were oxacillinases, followed by metallo-β-lactamases (MBL). In Enterobacteriaceae, characterization of carbapenemase types was less frequent, with oxacillinase 48 (OXA-48) being the most prevalent. The detection of multidrug-resistant organisms in recycled wastewater highlights an urgent need for routine microbiological monitoring in water management to protect both public health and agricultural sustainability. Full article

Hetero-multicomponent metal oxide catalysts are attracting increasing attention for wastewater remediation due to their tunable band structures, synergistic redox activity, and enhanced stability. This review thoroughly evaluates recent progress in the synthesis and application of such catalysts, highlighting Ti–Cu–Zn nanostructures as a representative case study. We examine synthesis approaches—including hydrothermal, biosynthesis, precipitation, and spray-based methods, with additional insight into sol–gel and other less commonly applied techniques—with emphasis on their suitability for constructing layered and multicomponent heterostructures. Mechanistic aspects of photocatalysis, Fenton and Fenton-like processes, adsorption, and electrochemical routes are discussed, with particular focus on charge separation, reactive oxygen species (ROS) generation, and pollutant-specific degradation pathways. Comparative performance metrics against antibiotics, pesticides, dyes, and fertilizers are analyzed, alongside considerations of leaching, reusability, and scale-up potential. Importantly, while significant progress has been made for organic micropollutants, applications in heavy metal remediation remain scarce, highlighting an urgent research gap. By situating Ti–Cu–Zn systems within the broader class of multicomponent catalysts, this review not only synthesizes current advances but also identifies opportunities to expand their role in sustainable wastewater management, including field deployment, regulatory compliance, and integration into decentralized treatment systems. Full article

The valorization of nutrient-rich institutional effluents represents a promising route for sustainable algal biotechnology. This study investigates the potential of canteen wastewater (CW) as an alternative culture medium for Spirulina platensis, integrating wastewater treatment with high-value carotenoid and lipid production. Growth performance, biochemical composition, and nutrient removal efficiencies were systematically evaluated in 2 L photobioreactors under optimized conditions. Spirulina cultured in 75% CW under 180 μmol photons m⁻² s⁻¹ achieved a biomass productivity of 0.071 g L⁻¹ day⁻¹, nearly three-fold higher than the synthetic BG-11 control (0.023 g L⁻¹ day⁻¹). Nutrient remediation was highly efficient, with 92.12% nitrate and 90.05% phosphate removal, effectively reducing effluent concentrations below discharge limits. Biochemical profiling revealed that wastewater-grown biomass contained 54.3% protein and 7.85% lipids, with a remarkable carotenoid yield of 21.81 mg g⁻¹ DW—significantly higher than the control (6.85 mg g⁻¹ DW). Mechanistic analysis suggests that the balanced nutrient stoichiometry (C:N:P ≈ 30:4:1) and mixotrophic conditions enhanced biomass quality while mitigating ammonia toxicity. This study demonstrates the first integrated application of canteen wastewater for dual-purpose bioremediation and pigment-rich biomass production, establishing a scalable circular bioeconomy framework for institutional waste management. Full article