Search Results (765)

Herein, α-MnO₂-supported Pt-Pd bimetal (xPd-yPt/α-MnO₂; x and y are the weight loadings (wt%) of Pd and Pt, respectively; x = 0, 0.23, 0.47, 0.93, and 0.92 wt%; and y = 0.91, 0.21, 0.46, 0.89, and 0 wt%) catalysts were prepared using the polyvinyl alcohol-protected NaBH₄ reduction method. The physicochemical properties of the catalysts were determined by means of various techniques and their catalytic activities for toluene oxidation were evaluated. It was found that among the xPd-yPt/α-MnO₂ samples, 0.93Pd-0.89Pt/α-MnO₂ showed the best catalytic performance, with the toluene oxidation rate at 156 °C (r_cat) and space velocity = 60,000 mL/(g h) being 6.34 × 10⁻⁴ mol/(g s), much higher than that of 0.91Pt/α-MnO₂ (1.31 × 10⁻⁴ mol/(g s)) and that of 0.92Pd/α-MnO₂ (6.13 × 10⁻⁵ mol/(g s)) at the same temperature. The supported Pd-Pt bimetallic catalysts possessed higher Mn³⁺/Mn⁴⁺ and O_ads/O_latt molar ratios, which favored the enhancement in catalytic activity of the supported Pd-Pt bimetallic catalysts. Furthermore, the 0.47Pd-0.46Pt/α-MnO₂ sample showed better resistance to sulfur dioxide poisoning. The partial deactivation of 0.47Pd-0.46Pt/α-MnO₂ was attributed to the formation of sulfate species on the sample surface, which covered the active site of the sample, thus decreasing its toluene oxidation activity. In addition, the in situ DRIFTS results demonstrated that benzaldehyde and benzoate were the intermediate products of toluene oxidation. Full article

Industrial catalysts are accelerating the global transition toward renewable energy, serving as enablers for innovative technologies that enhance efficiency, lower costs, and improve environmental sustainability. This review explores the pivotal roles of industrial catalysts in hydrogen production, biofuel generation, and biomass conversion, highlighting their transformative impact on renewable energy systems. Precious-metal-based electrocatalysts such as ruthenium (Ru), iridium (Ir), and platinum (Pt) demonstrate high efficiency but face challenges due to their cost and stability. Alternatives like nickel-cobalt oxide (NiCo₂O₄) and Ti₃C₂ MXene materials show promise in addressing these limitations, enabling cost-effective and scalable hydrogen production. Additionally, nickel-based catalysts supported on alumina optimize SMR, reducing coke formation and improving efficiency. In biofuel production, heterogeneous catalysts play a crucial role in converting biomass into valuable fuels. Co-based bimetallic catalysts enhance hydrodeoxygenation (HDO) processes, improving the yield of biofuels like dimethylfuran (DMF) and γ-valerolactone (GVL). Innovative materials such as biochar, red mud, and metal–organic frameworks (MOFs) facilitate sustainable waste-to-fuel conversion and biodiesel production, offering environmental and economic benefits. Power-to-X technologies, which convert renewable electricity into chemical energy carriers like hydrogen and synthetic fuels, rely on advanced catalysts to improve reaction rates, selectivity, and energy efficiency. Innovations in non-precious metal catalysts, nanostructured materials, and defect-engineered catalysts provide solutions for sustainable energy systems. These advancements promise to enhance efficiency, reduce environmental footprints, and ensure the viability of renewable energy technologies. Full article

The precise synthesis of non-precious metal single-atom electrocatalysts is crucial for enhancing the yield of highly active reactive oxygen species (ROSs). Conventional oxidation methods, such as Fenton or NaClO processes, suffer from poor efficiency, high energy demand, and secondary pollution. In contrast, heterogeneous electro-Fenton systems based on cascade oxygen reduction reactions (ORRs), which require low operational voltage and cause pollutant degradation through both direct electron transfer and ROS generation, have emerged as a promising alternative. Recent studies showed that carbon cathodes decorated with atomically dispersed transition metals can effectively integrate the excellent conductivity of carbon supports with the tunable surface chemistry of metal centers. However, the electronic structure of active sites intrinsically hinders the simultaneous achievement of high activity and selectivity in cascade ORRs. This review summarizes the advances, specifically from 2020 to 2025, in understanding the mechanism of cascade ORRs and the synthesis of transition metal-based single-atom catalysts in cathode electrocatalysis for efficient wastewater treatment, and discusses the key factors affecting treatment performance. While employing atomically engineered cathodes is a promising approach for energy-efficient wastewater treatment, future efforts should overcome the barriers in active site control and long-term stability of the catalysts to fully exploit their potential in addressing water pollution challenges. Full article

Biodiesel, a renewable and environmentally friendly alternative to fossil fuels, has attracted significant attention due to its potential to reduce greenhouse gas emissions. However, high production costs and complex processing remain challenges. Heterogeneous catalysts have shown promise in overcoming these barriers by offering benefits, such as easy separation, reusability, low-cost raw materials, and the ability to reduce reaction times and energy consumption. This review evaluates key classes of heterogeneous catalysts, such as metal oxides, ion exchange resins, and zeolites, and their performance in transesterification and esterification processes. It highlights the importance of catalyst preparation methods, textural properties, including surface area, pore volume, and pore size, activation techniques, and critical operational parameters, like the methanol-to-oil ratio, temperature, time, catalyst loading, and reusability. The analysis reveals that catalysts supported on high surface area materials often achieve higher biodiesel yields, while metal oxides derived from natural sources provide cost-effective and sustainable options. Challenges, such as catalyst deactivation, sensitivity to feedstock composition, and variability in performance, are discussed. Overall, the findings underscore the potential of heterogeneous catalysts to enhance biodiesel production efficiency, although further optimization and standardized evaluation protocols are necessary for their broader industrial application. Full article

This work aims to study the catalytic properties of Fe, Cr, and Cu catalysts deposited on chitosan–silica (SBA-15) composites in liquid phase oxidation of cyclohexane (CH) with H₂O₂ and photocatalytic hydrogen evolution reaction. The catalysts were obtained by consecutive adsorption of chitosan (CS) and metal ions (Fe³⁺, Cr³⁺, Cu²⁺) on SBA-15 at ambient conditions. Characterization of the catalysts by XRD, IR spectroscopy, XPS, TEM, SEM, etc., showed the CS and metal ion adsorption on the solid support. Modification with CS provided better immobilization of the metal ions on SBA-15. The synthesized catalysts demonstrated different performance in liquid phase oxidation of cyclohexane with H₂O₂ under mild conditions at 40 °C and atmospheric pressure. Cyclohexane conversion on Fe–CS/SBA-15 (18.5%) and Cr–CS/SBA-15 (21.6%) was higher than on Cu–CS/SBA-15 (9.3%). The influence of different conditions of the reaction such as time, temperature, catalyst dosage, substrate and oxidant ratio on cyclohexane conversion in the presence of the most efficient Cr–CS/SBA-15 catalyst was also studied. The optimal reaction conditions were found to be the following: duration of reaction—4 h, temperature of reaction—50 °C, m_cat—0.03 g, a substrate/H₂O₂ ratio of 1:3. In addition, Cr–CS/SBA-15 and Fe–CS/SBA-15 catalysts were studied in a photocatalytic H₂ evolution reaction. The Fe-containing catalyst demonstrated superior efficiency in photocatalytic H₂ evolution. The total volume of hydrogen produced within 3 h was 103 mL/g. Thus, this study demonstrates that chitosan possesses promising potential in the design of the supported catalysts for cyclohexane oxidation and photocatalytic hydrogen evolution reactions. Full article

Ag/AgCl-decorated layered lanthanum oxide (La₂O₃) and niobium pentoxide (Nb₂O₅) plasmonic photocatalysts are fabricated through an ionic liquid-mediated co-precipitation method. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), powder X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) techniques were used to illustrate the physicochemical properties of the materials. The photoactivity was evaluated for the degradation of Acid Blue 92 (AB92) azo dye, a typical organic contaminant from the textile industry, and U251 cancer cell inactivation. According to the results, Nb₂O₅–Ag/AgCl was able to remove >99% of AB92 solution in 35 min with the rate constant of 0.12 min⁻¹, 2.4 times higher than that of La₂O₃–Ag/AgCl. A pH of 3 and a catalyst dosage of 0.02 g were determined as the optimized factors to reach the highest degradation efficiency under solar energy at noon, which was opted to have the highest sunlight intensity over the reactor. Also, 0.02 mg/mL of Nb₂O₅–Ag/AgCl was determined to be of great potential to reduce cancer cell viability by more than 50%, revealed by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) and mitochondrial membrane potential (MMP) examinations. The mechanism of degradation was also discussed, considering the key role of Ag⁰ nanoparticles in inducing a plasmonic effect and improving the charge separation. This work provides helpful insights to opt for an efficient rare metal oxide with good biocompatibility as support for the plasmonic photocatalysts with the goal of environmental purification under sunlight. Full article

The development of efficient platinum group metal-free (PGM-free) catalysts for the hydrogen evolution reaction (HER) and the hydrogen oxidation reaction (HOR) is essential for advancing hydrogen-based energy technologies. In this study, Ni_xMo_100−x composites supported on Carbon Ketjenblack EC-300J (CK) were synthesized via thermal reduction under a controlled Ar/H₂ (95:5) atmosphere to investigate the effect of the Ni/Mo molar ratio on electrocatalytic performance. Structural and morphological analyses by XRD and TEM confirmed the formation of the NiMo alloys and carbide phases with controlled particle size distributions (~18 nm), while BET measurements revealed specific surface areas up to 124.69 m² g⁻¹ for the Pt-loaded samples. Notably, the 3% Pt/Ni₉₀Mo₁₀-CK catalyst exhibited outstanding bifunctional activity in a half-cell configuration, achieving an overpotential of 65.2 mV and a Tafel slope of 41.6 mV dec⁻¹ for the HER, and a Tafel slope of 32.9 mV dec⁻¹ with an exchange current density of 1.03 mA cm⁻² for the HOR. These results demonstrate that compositional tuning and minimal Pt incorporation synergistically enhance the catalytic efficiency, providing a promising platform for next-generation hydrogen electrocatalysts. Full article

Catalytic methane decomposition offers an attractive and sustainable pathway for producing CO_x-free hydrogen and valuable carbon nanotubes. This work investigates the innovative use of liquid metals, particularly gallium and indium, as promoters for iron catalysts based on a titanium dioxide and alumina composite to improve this process even more. In a fixed-bed reactor operating at 800 °C and atmospheric pressure, all catalyst activities for methane decomposition were thoroughly assessed while keeping the gas hourly space velocity at 6 L/g h. Surface area and porosity, H₂-temperature programmed reduction/oxidation, X-ray diffraction, Raman spectroscopy, scanning transmission electron microscopy, and thermogravimetry analysis were utilized to investigate the physicochemical properties of the catalyst. The result showed that iron supported on a titanium-alumina catalyst exhibited higher activity, stability, and reproducibility with a methane conversion of 90% and hydrogen production of 81% after three cycles, with 240 min for each cycle and stability for 480 min. In contrast, the liquid metal-promoted catalysts improved the metal-support interaction and textural properties, such as surface area, pore volume, and particle dispersion of the catalysts. Still, the catalytic efficiency significantly improved. However, the gallium-promoted catalyst displayed excellent reusability. The characterization of the spent catalyst proved that both the iron supported on a titanium-alumina and its gallium-promoted derivative produced graphitic carbon; on the contrary, the indium-promoted catalyst produced amorphous carbon. These results demonstrate how liquid metal promoters can be used to adjust the characteristics of catalysts, providing opportunities for improved reusability and regulated production of carbon byproducts during methane decomposition. Full article

Solid oxide fuel cells (SOFCs) have been considered as alternative energy conversion devices because of their high energy conversion efficiency, fuel flexibility, and cost efficiency without precious metal catalysts. In current SOFCs, the cermet anode consists of nickel and ion-conducting ceramic materials, and solid oxide electrolytes and ceramic cathodes have been used. SOFCs normally operate at high temperatures because of the lower ion conductivity of ceramic components at low temperatures, and they have weaknesses in terms of mechanical strength and durability against thermal shock originating from the properties of ceramic materials. To solve these problems, metal-supported solid oxide fuel cells (MS-SOFCs) have been designed. SOFCs using metal substrates, such as Ni-based and Cr-based alloys, provide significant advantages, such as a low material cost, ruggedness, and tolerance to rapid thermal cycling. In this article, SOFCs are introduced briefly, and the types of metal substrate used in MS-SOFCs, as well as the advantages and disadvantages of each metal support, are reviewed. Full article

2,5-Furandicarboxylic acid (FDCA) is a bio-based platform chemical with high potential to replace terephthalic acid in polymer production, particularly for polyethylene furanoate (PEF), a biopolymer with superior thermal and barrier properties. This study investigates the selective oxidation of 5-hydroxymethylfurfural (HMF) into FDCA using nickel-based heterogeneous catalysts, aiming at a cost-effective and sustainable alternative to noble metal catalysts. A series of nickel oxide catalysts were synthesized and screened. The NiOx catalyst synthesized without thermal treatment via Route B showed the best performance, achieving a FDCA yield of 11.77%, selectivity of 27.41%, and concentration of 0.9 g/L under preliminary conditions. Reaction kinetics revealed that the controlled addition of NaClO enhanced FDCA yield by 2.28 times. Optimization using a 2³ factorial design identified the optimal conditions as 6% (w/v) catalyst concentration, 25 °C, and a NaClO:HMF molar ratio of 12:1, leading to 34.14% yield and 42.57% selectivity. The NiOx catalyst maintained its activity over five successive cycles, indicating good recyclability. Moreover, NiOx demonstrated catalytic activity with crude HMF derived from glucose dehydration, confirming its practical applicability. These results support the potential of nickel-based catalysts in sustainable FDCA production, contributing to the advancement of bio-based polymer synthesis. Full article

The electrochemical reduction of nitrate to ammonia offers a promising solution for both alleviating nitrate pollution in wastewater and providing a sustainable ammonia source for agriculture use. This review focuses on the role of carbon-based catalysts in electrochemical nitrate reduction to ammonia, emphasizing their potential in addressing environmental pollution and supporting sustainable ammonia production. Carbon materials, known for their abundance, affordability, and eco-friendly properties, are central to this process. The review highlights key strategies for enhancing catalytic performance, including heteroatom doping, the development of porous structures, and the integration of metal/metal oxide nanoparticles. Additionally, it addresses significant challenges such as weak nitrate adsorption, slow reaction kinetics, and competition with the hydrogen evolution reaction. Through the integration of advanced material design, mechanistic insights, and innovative engineering strategies, this review provides valuable guidance for the future design of carbon-based catalysts, paving the way for significant advancements in both nitrate removal and sustainable ammonia synthesis. Full article

The anodic stability of tungsten carbide (WC) and iron oxide with a spinel structure (Fe₃O₄) were compared against similar data for nanostructured, boron-doped diamond (BDD), and the benchmark Vulcan XC72 carbon, in view of their eventual application as alternative supports for the anion exchange membrane electrolyzer anode. To this end, metal oxide composites were prepared by the in situ autocombustion (ISAC) method, and the anodic behavior of materials (composites as well as supports alone) was investigated in 1 M NaOH electrolyte by the rotating ring–disc electrode method, which enables the separation oxygen evolution reaction and materials’ degradation currents. Among all supports, BDD has proven to be the most stable, while Vulcan XC72 is the least stable under the anodic polarization, with Fe₃O₄ and WC demonstrating intermediate behavior. The Co₃O₄-BDD, -Fe₃O₄, -WC, and -Vulcan composites prepared by the ISAC method were then tested as catalysts of the oxygen evolution reaction. The Co₃O₄-BDD and Co₃O₄-Fe₃O₄ composites appear to be competitive electrocatalysts for the OER in alkaline medium, showing activity comparable to the literature and higher support stability towards oxidation, either in cyclic voltammetry or chronoamperometry stability tests. On the contrary, WC- and Vulcan-based composites are prone to degradation. Full article

Pharmaceuticals such as diclofenac (DCF), a widely used anti-inflammatory drug, are frequently detected in water bodies and pose serious environmental and health risks due to their persistence and low biodegradability. Although ozonation is an effective method for pollutant removal, its efficiency is often limited by low ozone utilization and incomplete mineralization. In this work, CuO/Al₂O₃- and MnO₂/Al₂O₃-supported catalysts were prepared via an impregnation method and evaluated for their performance in catalytic ozonation of diclofenac (DCF) in an aqueous solution. The catalysts were characterized by TEM, N₂ adsorption–desorption, FTIR, and XPS analyses. The effects of catalyst type, dosage, initial pH, and ozone flow rate on degradation efficiency were systematically investigated. Under optimal conditions, the DCF removal efficiencies reached 73.99% and 76.33% using CuO/Al₂O₃ and MnO₂/Al₂O₃, respectively, while COD removal efficiencies were 77.6% and 89.3%. Quenching experiments indicated that hydroxyl radicals (•OH) were the predominant reactive species involved in the catalytic ozonation process. The results demonstrate that supported CuO and MnO₂ catalysts can effectively enhance diclofenac degradation by ozone, offering potential for advanced water treatment applications. Full article

Solid oxide fuel cells (SOFCs) represent a pivotal technology in renewable energy due to their clean and efficient power generation capabilities. Their role in potential carbon mitigation enhances their viability. SOFCs can operate via a variety of alternative fuels, including hydrocarbons, alcohols, solid carbon, and ammonia. However, several solutions have been proposed to overcome various technical issues and to allow for stable operation in dry methane, without coking in the anode layer. To avoid coke formation thermodynamically, methane is typically reformed, contributing to an increased degradation rate through the addition of oxygen-containing gases into the fuel gas to increase the O/C ratio. The performance achieved by reforming catalytic materials, comprising active sites, supports, and electrochemical testing, significantly influences catalyst performance, showing relatively high open-circuit voltages and coking-resistance of the CH₄ reforming catalysts. In the next step, the operating principles and thermodynamics of methane reforming are explored, including their traditional catalyst materials and their accompanying challenges. This work explores the components and functions of SOFCs, particularly focusing on anode materials such as perovskites, Ruddlesden–Popper oxides, and spinels, along with their structure–property relationships, including their ionic and electronic conductivity, thermal expansion coefficients, and acidity/basicity. Mechanistic and kinetic studies of common reforming processes, including steam reforming, partial oxidation, CO₂ reforming, and the mixed steam and dry reforming of methane, are analyzed. Furthermore, this review examines catalyst deactivation mechanisms, specifically carbon and metal sulfide formation, and the performance of methane reforming and partial oxidation catalysts in SOFCs. Single-cell performance, including that of various perovskite and related oxides, activity/stability enhancement by infiltration, and the simulation and modeling of electrochemical performance, is discussed. This review also addresses research challenges in regards to methane reforming and partial oxidation within SOFCs, such as gas composition changes and large thermal gradients in stack systems. Finally, this review investigates the modeling of catalytic and non-catalytic processes using different dimension and segment simulations of steam methane reforming, presenting new engineering designs, material developments, and the latest knowledge to guide the development of and the driving force behind an oxygen concentration gradient through the external circuit to the cathode. Full article

Transition metal-based catalysts designed for efficient urea oxidation reactions (UOR) are essential for hydrogen production via urea-assisted water electrolysis. A series of amorphous nickel–cobalt boride catalysts supported on nickel foam were in situ synthesized via a stepwise chemical deposition method (SCDM). The systematic investigation focused on the relationships between synthesis parameters (deposition cycles, reactant feed ratio), morphological characteristics, and UOR performance. Notably, the optimized Co-NiB@NF catalyst exhibits a porous hierarchical architecture composed of metallic nanoparticles encapsulated by surface-wrinkled nanosheets, forming abundant exposed active sites. Electrochemical measurements demonstrate that this catalyst requires a low cell potential of 1.29 V to achieve a current density of 10 mA cm⁻². Moreover, it maintains 83% of the initial current density after 10 h of continuous electrolysis, highlighting its superior durability. The structural-property relationship revealed here provides valuable insights into the rational design of efficient amorphous boride catalysts for urea-assisted hydrogen production. Full article