Search Results (115)

Aeration is one of the most energy-intensive operations in wastewater treatment plants, with its efficiency strongly affected by the presence of surfactants. This study investigates the impact of Sodium Dodecyl Sulphate (SDS) on oxygen mass transfer using a commercial fine-bubble diffuser. Oxygen transfer experiments were performed under varying air flow rates and SDS concentrations. Key parameters, including the volumetric mass transfer coefficient ($k_{L}a$), gas holdup, bubble size, and interfacial area, were experimentally measured and analysed. SDS reduces the average bubble diameter by up to 50%; above 4 mg/L, further increases in concentration do not change the bubble size. Gas holdup increases by approximately 2% per mg L⁻¹ of SDS, and a new empirical correlation was proposed to predict gas holdup as a function of air flow rate and surfactant concentration, achieving an R² of 0.97 with deviations below 10%. Despite the increase in interfacial area, SDS strongly suppresses interfacial turbulence, reducing the liquid-side mass transfer coefficient ($k_L$) by up to 70%, which ultimately leads to a significant loss of overall oxygen transfer efficiency. The Sardeing model, originally developed for single bubbles, successfully predicted $k_L$ within ±15% of the experimental values, demonstrating its potential as a practical tool for estimating oxygen transfer in aeration systems. These findings highlight the substantial impact of surfactants on fine-bubble aeration performance and underscore the need to account for their effects in the design and operation of industrial aeration systems. Full article

Accidental and deliberate poisoning by Ricinus communis, a wild plant cultivated for castor oil, has been known for centuries. Seeds contain one of the deadliest known plant toxins, ricin, along with its dimer RCA120. Due to its toxicity and ease of extraction, ricin poses a potential threat as a chemical weapon, highlighting the need for reliable laboratory detection. In this work, ricin and RCA120 (Ricinus communis agglutinin) were extracted from castor beans and purified by solid-phase extraction (SPE) and Gel Permeation Chromatography (GPC). Purity was confirmed through Sodium Dodecyl Sulphate-PolyAcrylamide Gel Electrophoresis (SDS-PAGE). Then, lab-made standards were used to validate an Enzyme Linked ImmunoSorbent Assay (ELISA) kit to identify ricin in biological matrices after SPE extraction. Parallelly, SDS-PAGE was used to qualitatively confirm the presence of toxins. The developed method demonstrated a detection limit (LOD) of 2.74 ng/mL and was used to analyse biological specimens of seven human intoxication cases managed by Pavia Poison Control Centre (PCC). This study provides a quiet, inexpensive protocol that within 5 h allows the screening of potential ricin-exposure victims. Its implementation in clinical laboratories could support the management of intoxicated patients, ensuring faster and more accurate clinical response. Full article

This study compared the yield, percentage solids, electrophoretic profile, gelatinolytic activity, and brine shrimp lethality of Bitis arietans venom prepared using freeze-drying and desiccator drying. Bitis arietans venom was collected from snakes at Bioken snake farm, Kenya, whereafter it was pooled and divided into two parts. Part 1 was desiccator dried venom (DDV) while part 2 was freeze-dried venom (FDV). The yield and percentage solids in DDV and FDV were compared using Welch’s Student’s t-test and the dried venoms were subsequently subjected to sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE), 2D electrophoresis, gelatin in-gel zymography, and brine shrimp lethality assays. Mean venom yield and percentage solids did not differ between DDV and FDV (p = 0.5647 and p = 0.4676, respectively). SDS-PAGE and two-dimensional (2D) electrophoresis revealed similar protein profiles for DDV and FDV, showing bands and spot clusters within molecular weight ranges of ~16 kDa to >150 kDa and pH ranging from 3.5 to 9.5. Enzyme zymography revealed comparable gelatinolytic activity between DDV and FDV. However, the brine shrimp lethality assay indicated significantly higher toxicity in DDV (LC₅₀: 86.57 μg/mL) compared to FDV (LC₅₀: 460.37 μg/mL). DDV also showed greater lethality than FDV at 100 μg/mL (p = 0.0416) and 1000 μg/mL (p = 0.0008) but not at 10 μg/mL (p = 0.2465). These findings suggest that DDV exhibits higher toxicity in brine shrimp larvae than FDV, although both drying methods result in similar yields, percentage solids, venom profile, and gelatinolytic activity. Further research is necessary to investigate the mechanism behind this difference and its implications for antivenom production and long-term stability of venom. Full article

Several strategies, including UV detection with a diode array detector (DAD), laser-induced fluorescence (LIF), derivatization reactions, the use of micelles in the separation buffer, as well as online preconcentration techniques based on pressure-assisted electrokinetic injection (PAEKI), and offline preconcentration using solid-phase extraction (SPE) columns containing quaternary amine groups with a chloride counterion, were investigated for the simultaneous separation and signal amplification of free thyroid hormones (THs) in biological samples. Moreover, a sensitive method for the quantification of THs in selected biological samples using micellar electrokinetic capillary chromatography with LIF detection (MEKC-LIF) was developed. The THs present in biological samples (L-tyrosine, T2, T3, rT3, T4, and DIT) were successfully separated in less than 10 min. The analytes were separated following a derivatization procedure with fluorescein isothiocyanate isomer I (FITC). A background electrolyte (BGE) composed of 20 mM sodium tetraborate (Na₂B₄O₇) and 20 mM sodium dodecyl sulphate (SDS) was employed. Key validation parameters such as linearity, precision, limits of detection (LOD), and limits of quantification (LOQ) were determined. The use of PAEKI for the electrophoretic determination of free THs demonstrates significant potential for monitoring these hormones in real urine samples due to its high sensitivity and efficiency. Full article

Aqueous zinc ion batteries are considered one of the most promising energy storage devices due to their high safety, low cost, and ease of fabrication. However, the growth of anode dendrites and continuous side reactions during cycling limit the practical application of zinc ion batteries. In this paper, sodium dodecyl sulfate (SDS) was used as an aqueous electrolyte additive to improve the surface deposition of Zn²⁺. The experimental results show that the SDS electrolyte additive forms a protective layer on the anode surface through electrostatic action and inhibits the growth of dendritic protruding dendrites by increasing the zinc deposition overpotential, as well as by limiting the two-dimensional diffusion of Zn²⁺ on the negative electrode surface of the aqueous zinc ion battery. As a result, adding SDS improves the discharge specific capacity of NVP/Zn batteries at high voltages and results in improved capacity retention. The cycling stability of NVP/Zn batteries was greatly enhanced by using a battery containing 1% SDS that still had a discharge specific capacity of 71 mAh/g after 100 cycles at a charging current density of 1 C, with a capacity retention rate of 89%. This work provides a simple and feasible solution to the anode problem of aqueous zinc ion batteries. Full article

This study examines the adsorption and bulk assembly behaviour of quaternized hydroxyethylcellulose ethoxylate (QHECE)–sodium dodecyl sulphate (SDS) complexes on negatively charged substrates. Due to its quaternized structure, QHECE, which is used in several industries, including cosmetics, exhibits enhanced electrostatic interactions. The phase behaviour and adsorption mechanisms of QHECE–SDS complexes are investigated using model substrates that mimic the wettability and surface charge of damaged hair fibres. Two preparation methodologies, high-concentration mixing and gradient-free mixing, were employed to examine their impact on the complex equilibrium, phase behaviour, and adsorption properties of the complexes. The measurements of turbidity, electrophoretic mobility, and conductivity demonstrate the existence of nonequilibrium dynamics during the mixing process, which exert a significant influence on the structural and functional characteristics of the complexes. The quartz crystal microbalance with dissipation monitoring (QCM-D) was employed to investigate the adsorption of the complexes onto the substrates. The results demonstrated the critical role of intermediate SDS concentrations in enhancing deposition. The findings emphasise the importance of formulation and preparation protocols in designing stable, high-performance cosmetic products. This research advances our understanding of polyelectrolyte–surfactant interactions and provides insights into optimising QHECE-based formulations. Full article

Due to their indisputable biocompatibility and abundant source, biopolymers are widely used to prepare hydrogels for skin tissue engineering. Among them, cellulose is a great option for this challenging application due to its increased water retention capacity, mechanical strength, versatility and unlimited availability. Since algae are an unexploited source of cellulose, the novelty of this study is the decellularization of two different species, freshly collected from the Black Sea coast, using two different chemical surfactants (sodium dodecyl sulphate and Triton X-100), and characterisation of the resulted complex biopolymeric 3D matrices. The algae nature and decellularization agent significantly influenced the matrices porosity, while the values obtained for the hydration degree included them in hydrogel class. Moreover, their capacity to retain and then controllably release an anti-inflammatory drug, ibuprofen, led us to recommend the obtained structures as drug delivery systems. The decellularized macroalgae hydrogels are bioadhesive and cytocompatible in direct contact with human keratinocytes and represent a great support for cells. Finally, it was noticed that human keratinocytes (HaCaT cell line) adhered and populated the structures during a monitoring period of 14 days. Full article

In this study, we demonstrate the electrodeposition of copper nanoparticles (NPs) on pencil graphite electrodes (PGEs) utilizing sodium dodecyl sulphate (SDS) as a soft template. The utilization of the surfactant had an impact on both the physical arrangement and electrochemical characteristics of the modified electrodes. The prepared Cu-SDS/PGE electrodes had hierarchical dendritic structures of copper NPs, thereby increasing the surface area and electrochemical catalytic activity in comparison with Cu/PGE electrodes. The Cu-SDS/PGE electrode showed excellent catalytic activity in reducing hydrogen peroxide, resulting in the sensitive and selective detection of hydrogen peroxide. The electrode exhibited a good sensitivity of 21.42 µA/µM/cm², a lower limit of detection 0.35, and a response time of less than 2 s over a wide range spanning 1 µM to 1 mM of hydrogen peroxide concentrations. The electrodes were also highly selective for H₂O₂ with minimal interference from other analytes even at concentrations higher than that of H₂O₂. The approach offers the benefit of electrode preparation in just 5 min, followed by analysis in 10 min, and enables for the quantitative determination of hydrogen peroxide within 30 min. This can be achieved utilizing a newly prepared, cost-effective electrode without the need for complex procedures. Full article

A method to determine aceclofenac, ketorolac, and sulindac in human urine samples using microemulsion electrokinetic chromatography (MEEKC) has been developed in this study. The optimization of MEEKC conditions was carried out by changing the microemulsion compositions including the buffer pH, borate salt concentration, surfactant concentration, co-surfactant concentration, organic modifier concentration, and oil droplet concentration. The optimum separation of selected drugs was obtained with a composition of microemulsion containing 10 mM borate buffer pH 9, 0.5% sodium dodecyl sulphate (SDS), 6.6% n-butanol, 6.0% acetonitrile, and 0.8% ethyl acetate. Excellent linearity was obtained in the range concentration of 25 to 200 ppm with r² > 0.999. Limits of detection (LOD, S/N = 3) and limits of quantification (LOQ, S/N = 10) were 2.72 to 4.75 and 9.08 to 15.85 ppm, respectively. The solid-phase extraction (SPE) method using C-18 as an adsorbent and the solid phase micro-tip extraction (SPMTE) method using multiwalled carbon nanotubes (MWCNTs) as an adsorbent were used to clean-up and pre-concentrate the urine samples prior to the MEEKC analysis. The best recoveries of the selected drugs in the spiked urine sample were 91 to 103% with RSD of 1.26 to 4.03% (n = 3) using the SPE-MEEKC method. Full article

IMUNOR is an oral biotherapeutic drug that had been developed, registered, and approved in 1997 in the Czech Republic and Slovakia. IMUNOR is a dialyzable leukocyte extract (DLE) prepared from swine leukocytes. It is characterized as a mixture of small peptides with molecular weights smaller than 12 kDa and a specific portion of nucleotides. The medical uses of IMUNOR include therapeutic applications within its registered range of indications, primarily for the treatment of immunodeficiencies, allergies, and certain acute or relapsing bacterial infections in adults and children. Despite the long-term clinical application of DLE, with strong evidence of positive therapeutic effects and no serious side effects, a detailed physicochemical specification of this mixture was lacking. We developed several methods for more in-depth physicochemical characterization of IMUNOR, including a spectrophotometric method for quantification of the total protein concentration and total DNA concentration in a mixture, several chromatographic methods for identification of individual components present in significant concentrations in IMUNOR, such as HPLC methods and the Sodium Dodecyl Sulphate Polyacrylamide Gel Electrophoresis method, and characterization of amino acid composition of this mixture. For the investigation of the variability among different batches of IMUNOR, five to nine representative batches from a standard manufacturing process on an industrial scale were utilized. Using the analytical methods, we verified and confirmed the batch-to-batch reproducibility of the biological product IMUNOR. Full article

Geopolymer foam concrete (GFC), an emerging thermal insulation material known for its environmentally friendly and low-carbon attributes, has gained prominence for its use in bolstering building energy efficiency. A critical challenge in GFC production is foam destabilization by the alkaline environment in which foam is supersaturated with salt. In this study, GFC was prepared by using triterpene saponin (TS), sodium dodecyl sulphate (SDS), and cetyltrimethylammonium bromide (CTAB) as blowing agents, with fly ash as the precursor and calcium carbide slag (CA) combined with Glauber’s salt (GS, Na₂SO₄ ≥ 99%) as the activator. The effect of GFC on mechanical properties was analyzed by examining its fluidity, pore structure, dry density, and compressive strength. The results show that TS has a stable liquid film capable of adapting to the adverse effects of salt supersaturation and alkaline environments. TS is highly stable in the GFC matrix, and so the corresponding pore size is small, and the connectivity is low in the hardened GFC. In addition, the hydration products of GFC exhibit different morphologies depending on the surfactant used. TS has better water retention due to hydrogen bonding, which facilitates the hydration process. Full article

Acridinium esters, due to their capability for chemiluminescence (CL), are employed as indicators and labels in biomedical diagnostics and other fields. In this work, the influence of ionic surfactants, hexadecyltrimethylammonium chloride and bromide (CTAC and CTAB, cationic) and sodium dodecyl sulphate (SDS, anionic) on the CL parameters and mechanism of representative emitter, 10-methyl-9-[(2-methylphenoxy)carbonyl]acridinium trifluoromethanesulphonate (2MeX) in a H₂O₂/NaOH environment, is studied. Our investigations revealed that the type of surfactant and its form in solution have an impact on the CL kinetic constants and integral efficiencies, while changes in those emission properties resulting from the type of ion (Cl⁻ vs. Br⁻) are negligible. The major changes were recorded for systems containing surfactants at concentrations higher than the critical micelle concentration. The cationic surfactants (CTAC, CTAB) cause a substantial increase in CL emission kinetics and a moderate increase in its integral efficiency. At the same time, the opposite effect is observed in the case of SDS. Molecular dynamics simulations suggest that changes in emission parameters are likely due to differences in the binding strength of 2MeX substrate with surfactant molecules, which is higher for SDS than for CTAC. The results can help in rational designing of optimal acridinium CL systems and demonstrate their usefulness in distinguishing the pre- and post-micellar environment and the charge of surfactants. Full article

The exopolymer (ESPp) was obtained from Bacillus licheniformis IDN-EC, composed of a polyglutamic acid and polyglycerol phosphate chain O-substituted with αGal moieties (αGal/αGlcNH₂ 3:1 molar ratio) and with a 5000 Da molecular weight. The cytotoxicity activity of EPSp was determined by reducing the MTT (3-[4,5-dimethyl-thiazol-2-yl]-2,5-diphenyltetrazolium bromide) to formazan on HeLa cells. This EPS did not show cytotoxicity against the tested cell line. The ESPp presented great advantages as an antioxidant with free radical scavenging activities (1,1-diphenyl-2-picryl-hydrazyl radical (DPPH),hydroxyl radical (OH), and superoxide anion (O₂₋)) (65 ± 1.2%, 98.7 ± 1.9%, and 97 ± 1.7%), respectively. Moreover, EPSp increased the enzyme activity for catalase (CAT) and glutathione peroxidase (GSH-Px) in HeLa cells (CAT, 2.6 ± 0.24 U/mL; and GSH-Px, 0.75 ± 0.3 U/L). The presence of ESPp showed a significant protective effect against H₂O₂ in the cell line studied, showing great viability (91.8 ± 2.8, 89.9 ± 2.9, and 93.5 ± 3.6%). The EPSp presented good emulsifying activity, only for vegetable oils, olive oil (50 ± 2.1%) and sesame (72 ± 3%). Sesame was effective compared to commercials products, Triton X-100 (52.38 ± 1.6%), Tween 20 (14.29 ± 1.1%), and sodium dodecyl sulphate (SDS) (52.63 ± 1.6%). Furthermore, the EPS produced at 0.6 M has potential for environmental applications, such as the removal of hazardous materials by emulsification whilst resulting in positive health effects such as antioxidant activity and non-toxicity. EPSp is presented as a good exopolysaccharide for various applications. Full article

The aim of this in vivo study was to compare total protein present in the salivary films (F) and acquired enamel pellicle (AEP) on eroded and non-eroded surfaces in patients suffering from GORD symptoms with and without GORD diagnosis (GORD, No-GORD). Thirty-nine patients suffering from GORD symptoms and erosive tooth wear on lower first molars and an unaffected posterior occlusal surface in the same quadrant were recruited from Guy’s hospital, London. Salivary film and AEP were collected from the eroded and uneroded occlusal surfaces, using 0.5% sodium dodecyl sulphate (SDS)-soaked filter papers. Total protein concentration was analysed using bicinchoninic acid assay (BCA). Statistical analysis was conducted using Shapiro–Wilk, ANOVA, and Tukey’s tests (p < 0.05), comparing four GDS sample types and GORD vs. No-GORD groups. The level of significance was set as p < 0.05. Data were compared between eroded and uneroded surfaces in the same patient with GORD symptoms, as well as between those with or without a GORD diagnosis (GORD, No-GORD). The AEP total protein concentration from the eroded [2.17 (0.49) mg/mL] and uneroded surfaces [2.24 (0.66) mg/mL] of the GORD group were statistically significantly lower than those on eroded [3.27 (1.01) mg/mL] and uneroded [3.33 (1.57) mg/mL] surfaces in the No-GORD group (p = 0.007) (p = 0.008), respectively. No statistically significant differences were observed for film and AEP between eroded and uneroded surfaces (p > 0.05). Full article

Microalgae are a valuable source of lipids, proteins, and pigments, but there are challenges in large-scale production, especially in harvesting. Existing methods lack proven efficacy and cost-effectiveness. However, flocculation, an energy-efficient technique, is emerging as a promising solution. Integrating surfactants enhances microalgal harvesting and disruption simultaneously, reducing processing costs. This study investigated cetyltrimethylammonium bromide (CTAB), dodecyltrimethylammonium bromide (DTAB), and sodium dodecyl sulphate (SDS) for harvesting Tetraselmis sp. strains (75LG and 46NLG). CTAB exhibits superior results, with 88% harvesting efficiency at 1500 and 2000 mg L⁻¹ for 75LG and 46NLG, respectively, for 60 min of sedimentation—thus being able to reduce the operating time. Beyond evaluating harvesting efficiency, our study explored the kinetics of the process; the modified Gompertz model led to the best fit. Furthermore, the largest kinetic constants were observed with CTAB, thus highlighting its efficacy in optimising the microalgal harvesting process. With the incorporation of the suggested enhancements, which should be addressed in future work, CTAB could hold the potential to optimise microalgal harvesting for cost-effective and sustainable large-scale production, eventually unlocking the commercial potential of microalgae for biodiesel production. Full article