Search Results (24)

Glass microspheres are essential components in horizontal road markings due to their retroreflective properties, enhancing visibility and safety under low-light conditions. Traditionally produced from soda-lime glass made with high-purity silica from sand, their manufacturing raises environmental concerns amid growing global sand scarcity. This study explores the viability of rice husk ash (RHA)—a high-silica byproduct of rice processing—as a sustainable raw material for microsphere fabrication. A glass composition containing 70 wt% SiO₂ was formulated using RHA and melted at 1500 °C. Microspheres were produced through flame spheroidization and characterized following the Brazilian standard NBR 16184:2021 for Type IB beads. The RHA-derived microspheres exhibited high sphericity, appropriate size distribution (63–300 μm), density of 2.42 g/cm³, and the required acid resistance. UV-Vis analysis confirmed their optical transparency, and the refractive index was measured as 1.55 ± 0.03. Retroreflectivity tests under standardized conditions revealed performance comparable to commercial counterparts. These results demonstrate the technical feasibility of replacing conventional silica with RHA in glass microsphere production, aligning with circular economy principles and promoting sustainable infrastructure. Given Brazil’s significant rice production and corresponding RHA availability, this approach offers both environmental and socio-economic benefits for road safety and material innovation. Full article

Glass-based microfluidic devices are essential for applications such as diagnostics and drug discovery, which utilize their optical clarity and chemical stability. This review systematically analyzes pulsed laser micromachining as a transformative technique for fabricating glass-based microfluidic devices, addressing the limitations of conventional methods. By examining three pulse regimes—long (≥nanosecond), short (picosecond), and ultrashort (femtosecond)—this study evaluates how laser parameters (fluence, scanning speed, pulse duration, repetition rate, wavelength) and glass properties influence ablation efficiency and quality. A higher fluence improves the material ablation efficiency across all the regimes but poses risks of thermal damage or plasma shielding in ultrashort pulses. Optimizing the scanning speed balances the depth and the surface quality, with slower speeds enhancing the channel depth but requiring heat accumulation mitigation. Shorter pulses (femtosecond regime) achieve greater precision (feature resolution) and minimal heat-affected zones through nonlinear absorption, while long pulses enable rapid deep-channel fabrication but with increased thermal stress. Elevating the repetition rate improves the material ablation rates but reduces the surface quality. The influence of wavelength on efficiency and quality varies across the three pulse regimes. Material selection is critical to outcomes and potential applications: fused silica demonstrates a superior surface quality due to low thermal expansion, while soda–lime glass provides cost-effective prototyping. The review emphasizes the advantages of laser micromachining and the benefits of a wide range of applications. Future directions should focus on optimizing the process parameters to improve the efficiency and quality of the produced devices at a lower cost to expand their uses in biomedical, environmental, and quantum applications. Full article

This paper presents an experimental approach to the study of the compressive strength, isothermal calorimetry and life cycle assessment (LCA) of alkali-activated pastes based on soda–lime–silica glass, established to investigate the effect of the nature and proportion of the activator. Four different activators are compared: Portland cement, sodium silicate, sodium carbonate (at four percentages by weight: 5, 10, 15 and 25 wt% relative to glass) and sodium hydroxide (3.5 wt%). Portland cement and sodium carbonate were added in dry form (powder), while sodium hydroxide (pellets) and silicate were used in solution. At room temperature, glass exhibited slow reaction kinetics, with mechanical performance increasing significantly beyond 28 days of curing. The nature of the activator had a direct impact on the mechanical performance of the activated glass. Cement-activated pastes and those containing 25 wt% of sodium carbonate developed strength at an early age (0–7 days). The other activators showed lower strength development before 28 days of reaction. While a higher activator content improved short-term performance, it also increased the environmental impact, primarily due to the activator. The LCA, conducted on 11 indicators, revealed that the environmental impact was largely driven by the type and amount of activator used. A performance impact indicator (PII) related to global warming was introduced to compare pastes with different performance values. At an early age (0–28 days), the PII was lower when the activator level was high but decreased over time as the strength improved. In terms of long-term performance (360 days), hydroxide and sodium carbonate (10 wt%) achieved compressive strengths of 91 and 74 MPa, respectively. These systems offered a balance between high performance and a reduced environmental impact, making them of interest for sustainable applications. Full article

One of the most recognized decorations of the pick-up technique is the millefiori glass, which has been commonly attributed to Venetian production. However, Portugal is the country where the largest known assemblage of this type of glass artefact has been studied and published. In this work, two important archeological contexts were selected: (1) Santa Clara-a-Velha monastery (SCV) and (2) São João de Tarouca monastery (SJT). The fragments selection was made based on the diversity of decorative motifs, colors, and original forms that has been associated with Portuguese production. The compositional characterization was conducted by performing micro-particle-induced X-ray emission (µ-PIXE) mapping, which facilitated the visualization of the distribution of different oxides across the different glass layers and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to obtain the major, minor, and trace elements composition, including rare earth elements (REEs) to determine which kind of raw materials were used. Additionally, µ-Raman spectroscopy was employed to investigate the opacifiers, while UV–Visible spectroscopy was used to study which chromophores are presented in the glass samples. All the analyzed glass layers can be considered to be of a soda–lime–silica type, and four different geological patterns (from GP1 to GP4) were detected and reported. This result can indicate that these objects were made by using silica sources taken from four different geological settings. Interestingly, the GP3 represents about 41% of the analyzed glass fragments and is compatible with the pattern detected in some production wastes found in two different archeological contexts located in Lisbon, which reinforces the veracity of the theory that this GP can be attributed to a Portuguese production. On the other hand, GP1 was probably attributed Granada provenance. Full article

The present research work focuses on the characterization and leachability evaluation of electric arc furnace dust (EAFD) and its vitreous outgrowths produced during vitrification with soda lime recycled glass (SLRG). EAFD is a hazardous industrial waste generated in the collection of particulate material during the steelmaking process via an electric arc furnace. Glasses of various syntheses were obtained during EAFD vitrification with various amounts of silica scrap (50, 60 and 70 wt%). The characterization of the as-received dust was carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM), in conjunction with Energy Dispersive X-ray Spectroscopy (EDS). The produced glasses during vitrification were studied by means of chemical and mineralogical analysis, whereas their microstructure in polished sections was examined by SEM/EDS. Their behavior during leaching was determined by the EN 12457-2 compliance leaching test and according to the results, the trace elements detected in the leachates were well below the corresponding regulatory limits. Full article

The paper presents experimental results regarding the synthesis of Portland clinker starting from raw mixes based on two types of clayey precursors, i.e., clay and marl (the most common types of raw materials used in the cement industry), with and without glass waste content. The soda-lime glass waste addition (5.36–5.59 wt %), used to control the silica ratio of the raw mix, improved the raw mix burnability and decreased the calcination temperature (by 20 °C), leading to a decrease in fuel consumption and contributing to the reduction in CO₂ emissions associated with clinker and cement production. The clinkers obtained by the calcination of raw mixes with glass waste content at 1430 °C with a 30 min plateau had a similar mineralogical composition and microstructure to the clinkers obtained from the reference raw mixes and fulfilled the requirements of the specific standard EN 197-1. The obtained clinkers were used to produce two types of Portland cement, i.e., a unitary cement (CEM I) and a binary blended cement with slag (CEM II/B-S). The main characteristics of these cements, i.e., loss on ignition, insoluble residue, sulfate and chloride contents, as well as the setting time and soundness, meet the conditions stipulated in the EN 197-1 standard. The values of compressive strength, assessed on mortars after 2, 7 and 28 days of curing, allow the classification of all CEM I cements in the 42.5 R class. In the case of CEM II/B-S cements, those obtained from raw mixes with clay can be classified in the 42.5 N class, while those obtained from raw mixes with marl are classified in the 32.5 R class. Full article

Transparent conductive films are widely used in electronic products and industrial fields. Ultra-thin Ag conductive nanofilm (ACF) was prepared on a soda lime silica glass (ordinary architectural glass) substrate with industrial magnetron sputtering equipment with AZO (Al₂O₃ doped ZnO) as the crystal bed and wetting layer. In order to improve the corrosion resistance and conductivity of the ACF, graphene nanosheets were modified on the surface of the ACF by electrospraying for the first time. The results show that this graphene modification could be carried out continuously on a meter scale. With the modification of the graphene layer, the corrosion rate of graphene-decorated ACF (G/ACF) can be reduced by 74.56%, and after 72 h of salt spray test, the conductivity of ACF samples without modification of graphene can be reduced by 34.1%, while the conductivity of G/ACF samples with modification of graphene can be reduced by only 6.5%. This work proves the potential of graphene modified ACF to prepare robust large-area transparent conductive film. Full article

We have successfully demonstrated that although there are significant analytical challenges involved in the qualitative discrimination analysis of sub-mm sized (microfragment) glass samples, the task can be solved with very good accuracy and reliability with the multivariate chemometric evaluation of laser-induced breakdown spectroscopy (LIBS) data or in combination with pre-screening based on refractive index (RI) data. In total, 127 glass samples of four types (fused silica, flint, borosilicate and soda–lime) were involved in the tests. Four multivariate chemometric data evaluation methods (linear discrimination analysis, quadratic discrimination analysis, classification tree and random forest) for LIBS data were evaluated with and without data compression (principal component analysis). Classification tree and random forest methods were found to give the most consistent and most accurate results, with classifications/identifications correct in 92 to 99% of the cases for soda–lime glasses. The developed methods can be used in forensic analysis. Full article

This study reports the results obtained on seventeen glass finds collected from the archaeological site of Muricelle near Cosenza in Calabria (Italy), dated between the first and third century AD. Chemical characterization was undertaken by using an electron probe micro analyser (EPMA). The glasses showed a soda–lime–silica composition indicating the use of the natron as a flux. The comparison between the collected data and those on coeval finds available from the literature allowed us to subdivide the Muricelle glass into three compositional groups: (1) Mn_a, classified as Roman-Mn glasses; (2) Mn_b, which can be compared to the Mn-unintentionally coloured Roman glasses; and (3) Sb + Mn, obtained by the recycling of the Sb and Mn Roman-type glasses. These groups were different not only with respect to the contents and the types of decolourants but also for soda, lime, and aluminium contents, highlighting the use of different raw materials in the primary glass production and also indicating the procedures used in secondary glass production. The compositional characteristics suggested the Levant region as the primary glass source for the Mn_a and Mn_b groups. On the other hand, the Sb + Mn group was obtained through recycling, involving the melting and mixing of two types of primary glass (Sb-decolourised and Mn-decolourised) of Egyptian and Levantine origins, respectively. Full article

The current study aims to enhance the efficiency of lead-free glass as a shielding material against radiation, solve the problem of the dark brown of bismuth glass, and reduce the accumulation of waste glass disposed in landfills by using soda-lime-silica SLS glass waste. The melt-quenching method was utilized to fabricate (WO${}_3{)}_x$ [(Bi${}_2$O${}_3$)${}_{0.2}$ (ZnO)${}_{0.3}$ (B${}_2$O${}_3$)${}_{0.2}$ (SLS)${}_{0.3}$]${}_{1-x}$ at 1200 °C, where x = (0, 0.01, 0.02, 0.03, 0.04, and 0.05 mol). Soda lime silica SLS glass waste, which is mostly composed of 74.1 % SiO${}_2$, was used to obtain SiO${}_2$. Radiation Attenuation parameters were investigated using narrow-beam geometry and X-ray fluorescence (XRF). Furthermore, the parameters related to radiation shielding were calculated. The results showed that when WO${}_3$ concentration was increased, the half-value layer was reduced, whereas the $\mu$ increased. It could be concluded that WBiBZn-SLS glass is a good shielding material against radiation, nontoxic, and transparent to visible light. Full article

Glass wastes that come from recycling plants do not often find a proper use, thus, they are discarded. In order to find future uses for these wastes, this paper explores the characterization of waste glasses (WGs) as a raw material through the assessment of their light reflectance if they were used for external coatings in building materials. To this aim, in this research, several clay-tile specimens were fabricated and coated with three different compositions of waste glass. For these specimens, three variables were analyzed to serve for this WG-based coating characterization: thickness of WG coating, temperature, and holding time of burning. The resulting WG-coated tiles were assessed in terms of the light spectral reflectance and whiteness index, with the help of a fiber optic spectrometer. Results show that the composition of WG had a very significant influence on the light spectral reflectance and the degree of whiteness, with holding time and WG thickness being the most influential depending on the WG type. The temperature of burning was also shown to be critical for the densification process. Finally, an interpretation of these results based on the WG chemical composition coatings obtained by XRF is discussed in this paper. Full article

In the current study, BaO was doped in Bi₂O₃-ZnO-B₂O₃-SLS glass to develop lead-free radiation shielding glasses and to solve the dark brown of bismuth glass. The melt-quenching method was utilized to fabricate (x) BaO (1 − x)[0.3 ZnO 0.2 Bi₂O₃ 0.2 B₂O₃ 0.3 SLS] (where x are 0.01, 0.02, 0.03, 0.04, and 0.05 mol) at 1200 °C. Soda lime silica glass waste (SLS), which is mostly composed of 74.1% SiO₂, was used to obtain SiO₂. The mass attenuation coefficient (${\mu }_m$) was investigated utilizing X-ray fluorescence (XRF) at 16.61, 17.74, 21.17, and 25.27 keV and narrow beam geometry at 59.54, 662, and 1333 keV. Moreover, the other parameters related to gamma ray shielding properties such as half-value layer (HVL), mean free path (MFP), and effective atomic number ($Z_{eff}$) were computed depending on ${\mu }_m$ values. The results indicated that HVL and MFP decreased, whereas ${\mu }_m$ increased with an increase in BaO concentration. According to these results, it can be concluded that BaO doped in Bi₂O₃-ZnO-B₂O₃-SLS glass is a nontoxic, transparent to visible light, and a good shielding material against radiation. Full article

The archaeological excavations at Villa San Pancrazio (Taormina, Italy) are bringing to light a vast Roman-Imperial residential quarter featuring luxurious dwellings decorated with wall paintings and mosaic floors, pointing it out as one of the most significant archaeological sites of the city. The polychrome and black and white mosaics recovered date back to the middle Imperial period, during the 2nd century AD. This work deals with the first archaeometric investigations of the materials employed for the tesserae production with the aim of elucidating the mineralogical composition and obtaining analytical evidence that can contribute to extracting information related to their production technology. For that purpose, a non-invasive methodology, based on micro energy dispersive X-ray fluorescence (μ-EDXRF) spectrometry and Raman spectroscopy, was used to characterize a wide selection of stone, ceramic and glass tesserae. Chemometric tools were exploited to manage the large set of elemental data collected on black and white lithic samples, providing essential clues for the subsequent investigations. The results evidenced the employment of natural lithotypes (calcareous sedimentary, dolomitic and volcanic) local and imported, and also artificial materials, such as ceramic made firing magnesium-rich clays, soda-lime-silica glasses made with different opacifying and coloring agents (such as calcium antimoniate, cobalt and copper). Full article

Glass ionomer cement (GIC) is a well-known restorative material applied in dentistry. The present work aims to study the effect of hydroxyapatite (HA) addition into GIC based on physical, mechanical and structural properties. The utilization of waste materials namely clam shell (CS) and soda lime silica (SLS) glass as replacements for the respective CaO and SiO₂ sources in the fabrication of alumino-silicate-fluoride (ASF) glass ceramics powder. GIC was formulated based on ASF glass ceramics, polyacrylic acid (PAA) and deionized water, while 1 wt.% of HA powder was added to enhance the properties of the cement samples. The cement samples were subjected to four different ageing times before being analyzed. In this study, the addition of HA caused an increment in density and compressive strength results along with ageing time. Besides, X-ray Diffraction (XRD) revealed the formation of fluorohydroxyapatite (FHA) phase in HA-added GIC samples and it was confirmed by Fourier Transform Infrared (FTIR) analysis which detected OH‒F vibration mode. In addition, needle-like and agglomeration of spherical shapes owned by apatite crystals were observed from Field Emission Scanning Electron Microscopy (FESEM). Based on Energy Dispersive X-ray (EDX) analysis, the detection of chemical elements in the cement samples were originated from chemical compounds used in the preparation of glass ceramics powder and also the polyacid utilized in initiating the reaction of GIC. Full article

Soda lime silica (SLS) waste as the source of silica (SiO₂) and ark clamshell (ACS) as the foaming agent has been utilized to fabricate the low-cost and lightweight foam glass-ceramics. A series of 1 and 6 wt% foam glass-ceramics were successfully prepared by the conventional solid-state sintering method at various sintering temperatures for 60 min. The bulk density of the samples has achieved minimum density (1.014 g/cm³) with maximum expansion (62.31%) at 6 wt% of the ACS content sintered at 800 °C for 60 min. The bulk density increases while the linear shrinkage and total porosity decrease with the progression of ACS contents and sintering temperature, where the results correspond with the FESEM micrograph. The result of XRD and FTIR transmittance spectra have shown that the formation of wollastonite crystal has occurred starting at 6 wt% of the ACS content sintered at 800 °C for 30 min. The highest mechanical performance (3.90 MPa) with an average total porosity (8.04%) is observed for the sample containing 1 wt% of ACS. It can be concluded that the composition of foam glass-ceramics (1 and 6 wt%) and sintering temperatures give significant results to the structural, physical, and mechanical properties of the fabricated foam glass-ceramics. Full article