Search Results (19)

Adsorption chillers can produce chilled and desalinated water using low-grade heat, but their performance is limited by low coefficient of performance (COP) and large system mass. Enhancing heat and mass transfer in the sorbent bed is key to improving efficiency. This work introduces and systematically evaluates binder-stabilized silica gel composites as a structural and thermal enhancement strategy for adsorption chillers. Silica gel composites bonded with epoxy resin and polyvinyl alcohol (PVA) were evaluated for adsorption chiller applications. Thermal stability, conductivity, microstructure, equilibrium sorption, and sorption hysteresis were assessed. The results indicate that PVA-based composites were thermally unstable and discarded, whereas epoxy-bonded silica gel showed high thermal stability and mechanically robust granules with preserved pore connectivity. The epoxy composite exhibited 109% higher thermal conductivity than loose silica gel, improving internal heat transfer. This improvement is accompanied by a reduction in sorption capacity of approximately 58%, attributable to the inert resin fraction. Notably, the composite exhibits a reduced and locally negative sorption hysteresis, indicating facilitated desorption and lowered internal diffusion resistance. The epoxy-bonded silica gel therefore provides a promising combination of thermal stability, improved heat transfer, and enhanced sorption–desorption behaviour, supporting its potential to increase the efficiency of next-generation adsorption chillers. Full article

In this study, an innovative dental functionalized magnetic nanomaterial was developed by incorporating hydrophilic magnetic clusters as an alternative to conventional isolated magnetic nanoparticles, introducing a novel structural and functional concept in dental applications. The ~100 nm magnetic clusters—composed of densely packed 7 nm Fe₃O₄ nanoparticles—were sequentially coated with a silica (SiO₂) layer (3–5 nm) to improve chemical and mechanical stability, followed by an outer calcium hydroxide [Ca(OH)₂] layer to enhance bioactivity and optical integration. This bilayer architecture enables magnetic field-assisted positioning and improved dispersion within dental resin matrices. Silver nanoparticles were incorporated to enhance antimicrobial activity and reduce biofilm formation. The synthesis process was environmentally friendly and scalable. Comprehensive physicochemical characterization confirmed the material’s functional performance. Saturation magnetization decreased progressively with surface functionalization, from 62 to 14 emu/g, while the zeta potential became increasingly negative (from −2.42 to −22.5 mV), supporting its ability to promote apatite nucleation. The thermal conductivity (0.527 W/m·K) closely matched that of human dentin (0.44 W/m·K), and the colorimetric analysis showed improved brightness (ΔL = 5.3) and good color compatibility (ΔE = 11.76). These results indicate that the functionalized magnetic nanomaterial meets essential criteria for restorative use and holds strong potential for future clinical applications. Full article

This study investigates hazardous emissions from foundry binder systems, comparing organic resins (phenolic urethane, furan, and alkaline-phenolic) and clay-bonded green sand with inorganic alternatives (sodium silicate and geopolymer). The research was conducted at the Fundaciόn Azterlan pilot plant (Spain), involving controlled chamber tests for the production of 60 kg iron alloy castings in 110 kg sand molds. The molds were evaluated under two configurations: homogeneous systems, where both mold and cores were manufactured using the same binder (five trials), and heterogeneous systems, where different binders were used for mold and cores (four trials). Each mold was placed in a metallic box fitted with a lid and an integrated gas extraction duct. The lid remained open during pouring and was closed immediately afterward to enable efficient evacuation of casting gases through the extraction system. Although the box was not completely airtight, it was designed to direct most exhaust gases through the duct. Along the extraction system line, different sampling instruments were strategically located for the precise measurement of contaminants: volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), phenol, multiple forms of particulate matter (including crystalline silica content), and gases produced during pyrolysis. Across the nine trials, inorganic binders demonstrated significant reductions in gas emissions and priority pollutants, achieving decreases of over 90% in BTEX compounds (benzene, toluene, ethylbenzene, and xylene) and over 94% in PAHs compared to organic systems. Gas emissions were also substantially reduced, with CO emissions lowered by over 30%, NO_x by more than 98%, and SO₂ by over 75%. Conducted under the Greencasting LIFE project (LIFE 21 ENV/FI/101074439), this work provides empirical evidence supporting sodium silicate and geopolymer binders as viable, sustainable solutions for minimizing occupational and ecological risks in metal casting processes. Full article

Sitagliptin, an important anti-diabetic drug, can be obtained using transaminase (TA) enzymes, which are known to be promising biocatalysts for the production of highly enantiopure amines under mild reaction conditions. In an industrial context, the use of immobilized enzymes can provide several advantages, such as the improved stability of the biocatalyst and easy product recovery. In this study, a new commercially available transaminase enzyme to produce sitagliptin was immobilized on inorganic and organic supports using two different approaches: adsorption and covalent bond formation. Among the inorganic media, non-functionalized silica gel was chosen for its stability and competitive cost. A range of commercially available resins with different functionalities have also been selected for their characteristics that can meet industrial standards. The immobilized biocatalysts were first tested in the transamination of acetophenone as a model substrate, which obtains, in most cases, higher conversions with respect to soluble enzymes. The best results in the enantioselective synthesis of sitagliptin were achieved with the sample immobilized on the epoxy- and octadecyl-functionalized methacrylic resin, which allowed the complete conversion of the corresponding ketone and high enantioselectivity (>99% ee). Moreover, the recycling of the supported enzyme could be performed in a continuous flow system without loss of activity for five consecutive runs. Full article

Microfluidic devices offer promising solutions for automating various biological and chemical procedures. Epoxy resin, known for its excellent mechanical properties, chemical resistance, and thermal stability, is widely used in high-performance microfluidic devices. However, the poor printability of epoxy has limited its application in 3D printing technologies for fabricating epoxy-based microfluidic devices. In this study, fumed silica is introduced into epoxy resin to formulate a yield-stress fluid suspension as a support bath for embedded 3D printing (e-3DP). The study demonstrates that increasing the fumed silica concentration from 3.0% to 9.0% (w/v) enhances the yield stress from 9.46 Pa to 56.41 Pa, the compressive modulus from 19.79 MPa to 36.34 MPa, and the fracture strength from 148.16 MPa to 168.78 MPa, while reducing the thixotropic time from 6.58 s to 1.32 s, albeit with a 61.3% decrease in the transparency ratio. The 6.0% (w/v) fumed silica–epoxy suspension is selected based on a balance between yield stress, transparency, and mechanical performance, enabling high-fidelity filament formation. Two representative microfluidic devices are successfully fabricated, demonstrating the feasibility of a fumed silica–epoxy suspension for the customizable e-3DP of epoxy-based microfluidic devices. Full article

This study aims to investigate the effects of three toughening agents—core–shell rubber particles (CSR), nano-silica particles (NSPs), and epoxidized polybutadiene (EPB)—on the performance of UV-LED-cured epoxy electronic encapsulants. By systematically comparing the curing behavior, thermomechanical properties, and impact resistance of different toughening agents in alicyclic epoxy resins, their potential applications in more environmentally friendly UV-cured electronic encapsulation are evaluated. The results show that NSP and CSR toughened samples have fast cured speed under 365 nm UV-LED light, but it affects the depth of curing under low energy conditions. They maintain high Tg, high modulus, and low thermal expansion coefficient (CTE), especially in the NSP-toughened sample. The EPB-toughened sample has good transparency for LED, but it has negative effects on Tg and CTE. This research provides essential theoretical and experimental data to support the development of high-performance UV-LED-cured epoxy encapsulation materials. Full article

Development in hemoglobin-based oxygen carriers (HBOCs) that may be used as alternatives to donated blood requires an extensive supply of highly pure hemoglobin (Hb) preparations. Therefore, it is essential to fabricate inexpensive, stable and highly selective absorbents for Hb purification. Molecular imprinting is an attractive technology for preparing such materials for targeted molecular recognition and rapid separations. In this case study, we developed human fetal hemoglobin (HbF)-imprinted polymer beads through the fusion of surface imprinting and Pickering emulsion polymerization. HbF was firstly covalently coupled to silica nanoparticles through its surface-exposed amino groups. The particle-supported HbF molecules were subsequently employed as templates for the synthesis of molecularly imprinted polymers (MIPs) with high selectivity for Hb. After removing the silica support and HbF, the resulting MIPs underwent equilibrium and kinetic binding experiments with both adult Hb (HbA) and HbF. These surface-imprinted MIPs exhibited excellent selectivity for both HbA and HbF, facilitating the one-step isolation of recombinant Hb from crude biological samples. The saturation capacities of HbA and HbF were found to be 15.4 and 17.1 mg/g polymer, respectively. The present study opens new possibilities for designed resins for tailored protein purification, separation and analysis. Full article

The use of immobilized alcohol dehydrogenases (ADHs) offers numerous advantages, especially in the reaction conditions required by industrial applications. Looking for more efficient and cost-effective methods of ADH immobilization, in this study we explored silica-based supports as an alternative to the use of functionalized polymeric resins. Three commercially available ADHs were immobilized by adsorption and covalent bond formation. The obtained supported biocatalysts were applied for the bioreduction of acetophenone and some derivatives with good yields and excellent enantioselectivity. The important intermediate (S)-1-[3,5-bis(trifluoromethyl)phenyl]ethanol was obtained with a high enantiomeric excess (>99%) by using the highest performing immobilized ADH sample. The reusability of this biocatalyst was investigated in a flow system for five consecutive runs; the experiments showed that the biocatalyst could be recycled without a loss of activity and enantioselectivity. Finally, cross-linking with the glutaraldehyde of the supported biocatalyst was also carried out to prevent the leaching of the enzyme during the catalytic reactions. Full article

This article presents woven carbon-fiber-reinforced polymer (CFRP) tubular mesh used as a reinforcement on the inner surface of hollow beams made of high-performance concrete (HPC). The tubular mesh was designed to serve as both the tensile and shear reinforcement of hollow beams intended for the construction of small self-supporting structures that could be assembled without mechanization. The reinforcement was prepared with a tri-axial weaving machine from carbon filament yarn and was homogenized using epoxy resin. The interaction of the composite reinforcement with the cementitious matrix was investigated, and the surface of the reinforcement was modified using silica sand and polyvinyl alcohol (PVA) fibers to improve cohesion. The sand coating enhanced bond strength, resulting in the significantly higher flexural strength of the hollow beam of 128%. The PVA fibers had a lower positive effect of 64% on the flexural strength but improved the ductility of the beam. Individual beams were connected by gluing steel parts directly inside the hollow core of the HPC beam. This procedure provides good interaction between the CFRP reinforcement and the glued steel insert and allows for the fast and simple assembly of structures. The weaving of additional layers of the CFRP reinforcement around HPC beams was also explored. A small structure made of the hollow HPC beams with inner composite reinforcement was constructed to demonstrate the possibilities of the presented technology. Full article

In this work, formulations of “environmentally compatible” silicone-based antifouling, synthesized in the laboratory and based on copper and silver on silica/titania oxides, have been characterized. These formulations are capable of replacing the non-ecological antifouling paints currently available on the market. The texture properties and the morphological analysis of these powders with an antifouling action indicate that their activity is linked to the nanometric size of the particles and to the homogeneous dispersion of the metal on the substrate. The presence of two metal species on the same support limits the formation of nanometric species and, therefore, the formation of homogeneous compounds. The presence of the antifouling filler, specifically the one based on titania (TiO₂) and silver (Ag), facilitates the achievement of a higher degree of cross-linking of the resin, and therefore, a better compactness and completeness of the coating than that attained with the pure resin. Thus, a high degree of adhesion to the tie-coat and, consequently, to the steel support used for the construction of the boats was achieved in the presence of the silver–titania antifouling. Full article

Silica, titania, and mixed silica–titania powders have been used as supports for loading 5 wt% Cu, 5 wt% Ag, and 2.5 wt% Cu-2.5 wt% Ag with the aim of providing a series of nanomaterials with antifouling properties. All the solids were easily prepared by the wetness-impregnation method from commercially available chemical precursors. The resulting materials were characterized by several techniques such as X-ray diffraction analysis, X-ray photoelectron spectroscopy, N₂ physisorption, and temperature-programmed reduction measurements. Four selected Cu and Ag SiO₂- and TiO₂-supported powders were tested as fillers for the preparation of marine antifouling coatings and complex viscosity measurements. Titania-based coatings showed better adhesion than silica-based coatings and the commercial topcoat. The addition of fillers enhances the resin viscosity, suggesting better workability of titania-based coatings than silica-based ones. The ecotoxicological performance of the powders was evaluated by Microtox luminescence tests, using the marine luminescent bacterium Vibrio fisheri. Further investigations of the microbiological activity of such materials were carried out focusing on the bacterial growth of Pseudoalteromonas sp., Alteromonas sp., and Pseudomonas sp. through measurements of optical density at 600 nm (OD_600nm). Full article

Noble metal catalysts currently dominate the landscape of chemical synthesis, but cheaper and less toxic derivatives are recently emerging as more sustainable solutions. Iron is among the possible alternative metals due to its biocompatibility and exceptional versatility. Nowadays, iron catalysts work essentially in homogeneous conditions, while heterogeneous catalysts would be better performing and more desirable systems for a broad industrial application. In this review, approaches for heterogenization of iron catalysts reported in the literature within the last two decades are summarized, and utility and critical points are discussed. The immobilization on silica of bis(arylimine)pyridyl iron complexes, good catalysts in the polymerization of olefins, is the first useful heterogeneous strategy described. Microporous molecular sieves also proved to be good iron catalyst carriers, able to provide confined geometries where olefin polymerization can occur. Same immobilizing supports (e.g., MCM-41 and MCM-48) are suitable for anchoring iron-based catalysts for styrene, cyclohexene and cyclohexane oxidation. Another excellent example is the anchoring to a Merrifield resin of an Fe^II-anthranilic acid complex, active in the catalytic reaction of urea with alcohols and amines for the synthesis of carbamates and N-substituted ureas, respectively. A SILP (Supported Ionic Liquid Phase) catalytic system has been successfully employed for the heterogenization of a chemoselective iron catalyst active in aldehyde hydrogenation. Finally, Fe^III ions supported on polyvinylpyridine grafted chitosan made a useful heterogeneous catalytic system for C–H bond activation. Full article

To evaluate the influence of the convergence angle of tooth preparations and abutments height and several surface treatments for zirconia copings through the tensile retention test. 120 crown preparations were made in Nema G10 with the maxillary first molar anatomy. In total, 60 abutments of 5 mm height were divided into two groups of 6° and 20° convergence angles of tooth preparations, and 60 abutments with a convergence angle of tooth preparations of 12° were divided into groups of 4 and 6 mm heights. Three surface treatments used were MDP-primer (10-Methacryloyloxydecyl dihydrogen phosphate), glazing or silica blasting. The abutments were scanned to make zirconia copings (3Y-TZP–Yttria-Stabilized Tetragonal Zirconia Polycrystals, Vita In-Ceram YZ). After cementation, the mechanical cycling (2 × 10⁶ cycles, 3 Hz, 100 N) was performed to aging. After cycling, the copings were tested in tensile (1 kN load cell; 0.5 mm/s speed). Both abutments support base and copings were embedded in acrylic resin with the aid of a device that maintained the long axis perpendicular to the horizontal plane. Data were analyzed with the two-way ANOVA and Tukey test (95%). ANOVA revealed that the convergence angle influenced the tensile retention (p = 0.0232), but the abutments height showed no statistically significant difference (p = 0.086). The MDP-primer and silica blasting showed higher retention forces in the specimens with height variations. For bonded zirconia crowns, the retention force provided by high convergence angle preparation is critical and cannot be improved by surface treatments. For short and long crown preparations, MDP-based Primers or Silica blasting are advisable to aid restoration longevity. Full article

This paper investigates the influence of silica nanoparticles on the mechanical properties of a unidirectional (UD) kenaf fiber reinforced polymer (KFRP) and hybrid woven glass/UD kenaf fiber reinforced polymer (GKFRP) composites. In this study, three different nanosilica loadings, i.e., 5, 13 and 25 wt %, and untreated kenaf fiber yarns were used. The untreated long kenaf fiber yarn was wound onto metal frames to produce UD kenaf dry mat layers. The silane-surface-treated nanosilica was initially dispersed into epoxy resin using a high-vacuum mechanical stirrer before being incorporated into the UD untreated kenaf and hybrid woven glass/UD kenaf fiber layers. Eight different composite systems were made, namely KFRP, 5 wt % nanosilica in UD kenaf fiber reinforced polymer composites (5NS-KFRP), 13% nanosilica in UD kenaf fiber reinforced polymer composites (13NS-KFRP), 25 wt % nanosilica in UD kenaf fiber reinforced polymer composites (25NS-KFRP), GKFRP, 5 wt % nanosilica in hybrid woven glass/UD kenaf fiber reinforced polymer composites (5NS-GKFRP), 13 wt % nanosilica in hybrid woven glass/UD kenaf fiber reinforced polymer composites (13NS-GKFRP) and 25 wt % nanosilica in hybrid woven glass/UD kenaf fiber reinforced polymer composites (25NS-GKFRP). All composite systems were tested in tension and bending in accordance with ASTM standards D3039 and D7264, respectively. Based on the results, it was found that the incorporation of homogeneously dispersed nanosilica significantly improved the tensile and flexural properties of KFRP and hybrid GKFRP composites even at the highest loading of 25 wt % nanosilica. Based on the scanning electron microscopy (SEM) examination of the fractured surfaces, it is suggested that the silane-treated nanosilica exhibits good interactions with epoxy and the kenaf and glass fibers. Therefore, the presence of nanosilica in an epoxy polymer contributes to a stiffer matrix that, effectively, enhances the capability of transferring a load to the fibers. Thus, this supports greater loads and improves the mechanical properties of the kenaf and hybrid composites. Full article

Every year, a large quantity of vanadium-containing wastewater is discharged from industrial factories, resulting in severe environmental problems. In particular, V(V) is recognized as a potentially hazardous contaminant due to its high mobility and toxicity, and it has received considerable attention. In this study, a silica-supported primary amine resin (SiPAR) was prepared by in-situ polymerization, and the V(V) adsorption from the solution was examined. The as-prepared resin exhibited fast adsorption kinetics, and it could attain an equilibrium within 90 min for the V(V) solution concentration of 100 mg/L at an optimum pH of 4, whereas the commercial D302 resin required a treatment time of more than 3 h under the same conditions. Furthermore, the maximum adsorption capacity of the resin under optimum conditions for V(V) was calculated to be 70.57 mg/g. In addition, the kinetics and isotherm data were satisfactorily elucidated with the pseudo-second-order kinetics and Redlich–Peterson models, respectively. The silica-based resin exhibited an excellent selectivity for V(V), and the removal efficiency exceeded 97% in the presence of competitive anions at 100 mmol/L concentrations. The film mass-transfer coefficient (k_f) and V(V) pore diffusivity (D_p) onto the resins were estimated by mathematical modeling. In summary, this study provided a potential adsorbent for the efficient removal of V(V) from wastewater. Full article