Search Results (8)

Fatigue properties remain a key challenge for aluminum–steel self-piercing riveted (SPR) joints in lightweight structures. This study evaluates shot peening as a pretreatment for the AA5052 sheet to improve the fatigue behavior of AA5052/SPFC440 dissimilar joints and to clarify the underlying mechanisms. Shot-peened and conventional SPR joints were prepared for comparison. Quasi-static tensile tests were conducted, and tension–tension fatigue tests were performed at high and low load levels. After shot peening, multiple factors with residual compressive stress, subsurface hardening, and surface roughness influenced the fatigue performance of the SPR joints. This led to a load-level-dependent fatigue behavior, with improved fatigue performance at low load levels and reduced performance at high load levels. At high load conditions, the increased surface roughness played a more significant role, with more crack initiation sites observed, resulting in fatigue lives comparable to or slightly lower than those of conventional joints. In contrast, at low load levels in the long-life regime, surface tensile stress was effectively reduced, crack initiation at surface defects was suppressed, and crack initiation shifted from the surface to subsurface regions, resulting in an 11.3% improvement in fatigue strength. These findings provide practical guidance for improving the fatigue performance of dissimilar-material SPR joints through material surface pretreatment. Full article

Ceramic panel collapse will easily lead to the failure of traditional targets. One strategy to solve this problem is to use separate ceramic units as armor panels. Based on this idea, we propose an aluminum matrix composite using pressure infiltration, containing an array of ceramic balls, the reinforcement of which consists of centimeter-scale SiC balls and micron-scale B₄C particles. Three different array layouts were designed and fabricated: compact balls in the front panel (F-C), non-compact balls in the front panel (F-NC), and compact balls inside the target (I-C). The penetration resistance properties were tested using a 12.7 mm armor-piercing incendiary (API). The results show that there are no significant internal defects, and the ceramic balls are well-bonded with the matrix composite. The F-NC structure behaves the best penetration resistance with minimal overall damage; the I-C structure has a large area of spalling and the most serious damage. Finite element simulation reveals that the ceramic balls play a major role in projectile erosion; in the non-compact structure, the composite materials between the ceramic balls can effectively disperse the stress, thereby avoiding the damage caused by direct contact between ceramic balls and improving the efficiency of ceramic ball erosion projectiles. Furthermore, it is essential to have a certain thickness of supporting materials to prevent spalling failure caused by stress wave transmission during penetration. This multi-scale composite exhibits excellent ballistic performance, providing valuable insights for developing anti-penetration composite armor in future applications. Full article

The evaluation of tube burring formability is a crucial task for finding a suitable material for tube-based automobile parts. The local strain at the ductile fracture site (fracture strain) should be evaluated for this purpose. Moreover, a cold-drawn steel tube has a strong anisotropic shaped microstructure and possibly causes anisotropic fracture strain behavior. Based on this background, the study evaluated the axial and hoop directional fracture strains of cold-drawn steel tubes using the small round-bar tensile specimen. The burnished surface ratio on the pierced surface was also investigated for possibility estimation of in-line formability inspection. As a result, three tubes are presented with inferior, nearly the same, and superior hoop directional fracture strains compared with the axial strains, where exceeding 40% deterioration in the hoop direction occurs by a combination of grain elongation and carbide aggregation. The scanning electron micrographs suggest that the microvoid growth and linkage percolated thorough carbides on the elongated grain boundaries. For the piercing test, the 30% fracture strain deterioration resulted in a 4% decrease in the burnished surface ratio on the pierced surface. This result suggested that the estimation of the pierced surface can detect material defects before the actual tube-burring process. Full article

Self-pierce riveting of three thin sheets of 980 MPa steel and 5052 aluminum alloy was performed to investigate the effect of sheet configuration on the deforming behaviors of the sheets and the rivet and joint strength. When the lower sheet was aluminum alloy, the joining range was relatively wide, i.e., the interlock hooking the rivet leg tended to be large. In the sheet configuration in which the upper and lower sheets were A5052 and the middle sheet was 980 MPa steel, the rivet leg spread out moderately and the joint without defects was obtained. In the lower 980 MPa steel sheet, fracture tended to occur due to the low ductility of the lower sheet, and the joining range was narrow with the small interlock although the three sheets were joined by an appropriate die shape. In joint strength of joined three sheets, fracture occurred in the lower-strength aluminum alloy sheet if interlocks of about 300 μm and 150 μm could be formed in the lower aluminum alloy sheet and 980 MPa steel sheet, respectively. Full article

A CVD (Chemical Vapor Deposition) diamond coated tungsten carbide (WC) and cobalt (Co) sintered alloy punch was trimmed by the femtosecond laser machining to sharpen its edge with about 2 μm and to simultaneously make nanostructuring to its side surface. In addition to the sharpened edge, its edge profile was formed to be homogeneous enough to reduce the damage layer width by piercing the electrical amorphous steel sheet stack. Each brittle sheet in the stacked work was damaged to have three kinds of defects by piercing; e.g., the droop-like cracking in the thickness and at the vicinity of hole, the wrinkling in peak-to-valley with partial cracking on the peaks, and the circumferential cracking. When using the WC (Co) punch with the inhomogeneous edge profile in the sharpened edge width, these three damages were induced into each sheet and the maximum damage width exceeded 80 μm. When using the punch with the sharpened edge and homogeneous edge profile, the wrinkling mode was saved and the total affected layer width was significantly reduced to less than 20 μm. Through the precise embossing experiments, this effect of punch edge profile condition to the induced damages was discussed with a statement on the nanostructuring effect on the reduction of damaged width in electrical amorphous steel sheets. The developed tool with the sharpened edge and homogenous edge condition contributes to the realization of a low iron loss motor with a reduced affected layer width. Full article

Metal flow tends to be complex and difficult to predict in the combined forward-backward extrusion (CFBE) process. Piercing and surface-crack defects are phenomenal in forming fasteners featuring a forward extruded pin and a backward extruded cup. In this work, a series of the CFBE tests with various combinations of the forward extrusion ratio (FER) and the backward extrusion ratio (BER) were conducted. A forming limit diagram, detailed with the piercing and surface-crack defects on the forward extruded pin or the backward extruded cup, was developed to provide a conception in choosing appropriate extrusion ratios in forming fasteners with such pin-and-cup features. With the aid of the forming load-stroke curves and the finite element analysis of fracture damage, the fracturing mechanism for the CFBE process was provided. Full article

This paper shows an overview of different analyses regarding current challenges at self-pierce riveting with solid rivets as well as semi-tubular rivets of lightweight materials like aluminum die casting, carbon fiber reinforced plastic and 7xxx series aluminum alloy. The joining process analyses will demonstrate the cause and the development as well as the influence on joint quality of individual joining process-induced defects. In addition, methods are described how these imperfections can be avoided or reduced. Full article

The scattering of Dirac electrons by topological defects could be one of the most relevant sources of resistance in graphene and at the boundary surfaces of a three-dimensional topological insulator (3D TI). In the long wavelength, continuous limit of the Dirac equation, the topological defect can be described as a distortion of the metric in curved space, which can be accounted for by a rotation of the Gamma matrices and by a spin connection inherited with the curvature. These features modify the scattering properties of the carriers. We discuss the self-energy of defect formation with this approach and the electron cross-section for intra-valley scattering at an edge dislocation in graphene, including corrections coming from the local stress. The cross-section contribution to the resistivity, ρ, is derived within the Boltzmann theory of transport. On the same lines, we discuss the scattering of a screw dislocation in a two-band 3D TI, like Bi_1-xSb_x, and we present the analytical simplified form of the wavefunction for gapless helical states bound at the defect. When a 3D TI is sandwiched between two even-parity superconductors, Dirac boundary states acquire superconductive correlations by proximity. In the presence of a magnetic vortex piercing the heterostructure, two Majorana states are localized at the two interfaces and bound to the vortex core. They have a half integer total angular momentum each, to match with the unitary orbital angular momentum of the vortex charge. Full article