Search Results (22)

Recent advancements in hybrid photonic integrated circuits (PICs) for wireless communications are reviewed, with a focus on innovations developed at Fraunhofer HHI. This work leverages hybrid integration technology, which combines indium phosphide (InP) active elements, silicon nitride (Si₃N₄) low-loss waveguides, and high-efficient thermal-optical tunable polymers with micro-optical functions to achieve fully integrated wireless transceivers. Key contributions include (1) On-chip optical injection locking for generating phase-locked optical beat notes at 45 GHz, enabled by cascaded InP phase modulators and hybrid InP/polymer tunable lasers with a 3.8 GHz locking range. (2) Waveguide-integrated THz emitters and receivers, featuring photoconductive antennas (PCAs) with a 22× improved photoresponse compared to top-illuminated designs, alongside scalable 1 × 4 PIN-PD and PCA arrays for enhanced power and directivity. (3) Beam steering at 300 GHz using a polymer-based optical phased array (OPA) integrated with an InP antenna array, achieving continuous steering across 20° and a 10.6 dB increase in output power. (4) Demonstration of fully integrated hybrid wireless transceiver PICs combining InP, Si₃N₄, and polymer material platforms, validated through key component characterization, on-chip optical frequency comb generation, and coherent beat note generation at 45 GHz. These advancements result in compact form factors, reduced power consumption, and enhanced scalability, positioning PICs as an enabling technology for future high-speed wireless networks. Full article

The transient dynamics of photocurrents for poly((4-diphenylamino)benzyl acrylate) (PDAA)-based photorefractive (PR) polymers sensitized with perylene bisimide derivative N,N′-diisopropylphenyl-1,6,7,12-tetrachloroperylene-3,4,9,10-tetracarboxyl bisimide (PBI) at various composition ratios were studied. The PR polymer included (4-(diphenylamino)phenyl)methanol (TPAOH) photoconductive plasticizer and (4-(azepan-1-yl)-benzylidene) malononitrile nonlinear optical dye as well, which are needed for inducing PR effects. All the photocurrents measured at 640 nm were well simulated by a two-trapping site model considering photocarrier generation and recombination processes of the charge transfer (CT) complex between PBI and PDAA. The process of photocurrent simulation allowed for analyses of the dependences of hole mobility, quantum efficiency (QE) of photocarrier generation, trapping parameters, and recombination coefficient on the PDAA/TPAOH content. Finally, the PDAA content dependences of the trapping and recombination properties were compared with those of the PR parameters of the optical diffraction efficiency, optical gain, and response time. Full article

This paper investigates the optoelectronic properties of CsPbBr₃, a lead-based perovskite, and Cs₂AgBiBr₆, a lead-free double perovskite, in composite thick films synthesized using mechanochemical and hot press methods, with poly(butyl methacrylate) as the matrix. Comprehensive characterization was conducted, including X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), UV–visible spectroscopy (UV–Vis), and photoluminescence (PL). Results indicate that the polymer matrix does not significantly impact the crystalline structure of the perovskites but has a direct impact on the grain size and surface area, enhancing the interfacial charge transfer of the composites. Optical characterization indicates minimal changes in bandgap energies across all different phases, with CsPbBr₃ exhibiting higher photocurrent than Cs₂AgBiBr₆. This is attributed to the CsPbBr₃ superior charge carrier mobility. Both composites showed photoconductive behavior, with Cs₂AgBiBr₆ also demonstrating higher-energy (X-ray) photon detection. These findings highlight the potential of both materials for advanced photodetector applications, with Cs₂AgBiBr₆ offering an environmentally Pb-free alternative. Full article

Here we present the cascade converter (CC), which provides real-time imaging of ionizing radiation (IoR) distribution. It was designed and manufactured with the simplest architecture, utilizing liquid crystal display (LCD) technology. Based on two merged substrates with transparent electrodes, armed with functional layers, with the cell filled with nematic liquid crystal, a display-like, IoR-stimulated CC was achieved. The CC comprises low-absorbing polymer substrates (made of polyethylene terephthalate—PET) armed with a transparent ITO electrode covered with a thin semipermeable membrane of polymer (biphenylperfluorocyclobutyl: BP-PFCB) doped with functional nanoparticles (NPs) of Lu₂O₃:Eu. This stack was covered with a photoconductive layer of α-Se and finally with a thin polyimide (PI) layer for liquid crystal alignment. The opposite substrate was made of LCD-type glass with ITO and polyimide aligning layers. Both substrates form a cell with a twisted structure of nematic liquid crystal (TN) driven with an effective electric field $E_{eff}$. An effective electric field driving TN structure is generated with a sum of (1) a bias voltage $V_{BIAS}$ applied to ITO transparent electrodes and (2) the photogenerated additional voltage $V_{Xray}$ induced between ITO and α-Se layers with a NPs-doped BP-PFCB polymer layer in-between. The IoR (here, X-ray) conversion into real imaging of the IoR distribution was achieved in the following stages: (1) conversion of IoR distribution into non-ionizing red light emitted with functional NPs, (2) transformation of red light into an electric charge distributed in a layer of the photoconductive α-Se, which is what results in the generation of distributed voltage $V_{Xray}$, and (3) a voltage-mediated, distributed switching of the TN structure observed with the naked eye. The presented imaging device is characterized by a simple structure and a simple manufacturing process, with the potential for use as a portable element of IoR detection and as a dosimeter. Full article

Polymer–semiconductor hybrid materials or composites have been investigated with respect to their microstructure, optical, photoconductive, and ferroelectric properties. For this purpose, either CdSe quantum dots or (Cd:Zn)S microparticles were dispersed in poly(vinylidenefluoride-trifluoroethylene) solution and hot pressed to films. In both material systems, the electrical conductivity and the polarization behavior could be controlled by the intensity of the optical excitation. The simultaneous high optical transparency of the CdSe quantum-dot-based hybrid materials makes them particularly interesting for applications in the field of flexible, high-resolution sensors. Full article

Polymer composites based on poly(N,N′-bis-4-butylphenyl-N,N′-bisphenyl)benzidine (poly-TPD) with PCBM and copper(II) pyropheophorbide derivative (Cu-PP) were developed. In thin films of the poly-TPD and Cu-PP composites, the charge carrier mobility was investigated for the first time. In the ternary poly-TPD:PCBM:Cu-PP composite, the electron and hole mobilities are the most balanced compared to binary composites and the photoconductivity is enhanced due to the sensitization by Cu-PP in blue and red spectral ranges. The new composites are promising for use in the development of photodetectors. Full article

The ellipsometric analyses reported in this paper present a novelty by bringing an in-depth optical investigation of some ternary organic blends. This study focuses on the tunability and control of the relative permittivity of active layers by varying the weight ratio of blended materials spin-coated as thin films. To investigate this, an extensive approach based on spectroscopic ellipsometry was conducted on ternary blend (D:A₁:A₂) thin films, involving a donor [D = chlorinated conjugated polymer (PBDB-T-2Cl)] and two acceptor materials [A₁ = a non-fullerene (ITIC-F) and A₂ = a fullerene (PCBM)]. The refractive index constitutes a key parameter that exposes insights into the feasibility of photovoltaic cells by predicting the trajectory of light as it transits the device. In this term, higher obtained refractive indexes support higher absorption coefficients. Notably, the dielectric constant can be rigorously tuned and finely calibrated by modest variations in the quantity of the third element, resulting in considerable modifications. Moreover, the inclusion of fullerene in blends, as the third element, results in a smooth topographical profile, further refining the surface of the film. From an electrical point of view, the ternary blends outperform the polymer thin films. The synergistic interaction of constituents emphasizes their potential to enhance solar conversion devices. Full article

Transformation into electric or photoelectric functional composite from non-conjugated polymers is a great challenge due to the presence of a large number of locative states. In this paper, carbon nanofiber was synthesized via hydrothermal carbonization utilizing carboxymethyl cellulose as a precursor, and the carbon nanofiber/Cu nanocomposite was constructed for defect passivation. The results indicated that the resulting nanocomposites exhibited good absorbance in visible light range and NIR (near-infrared). The photoconductive responses to typical weak visible light (650 nm et al.) and NIR (808, 980, and 1064 nm) were studied based on Au gap electrodes on flexible polymer substrates. The results exhibited that the nanocomposite’s solid thick film showed photocurrent-switching behaviors to visible light and NIR, the switch-ratio was depending on the wavelengths and power of incident lights. The positive and negative photoconductance responses phenomenon was observed in different compositions and changing excited wavelengths. Their photophysical mechanisms were discussed. This illustrated that the nanocomposites easily produce free electrons and holes via low power of incident light. Free electrons and holes could be utilized for different purposes in multi-disciplinary fields. It would be a potential application in broadband flexible photodetectors, artificial vision, simulating retina, and bio-imaging from visible light to NIR. This is a low-cost and green approach to obtain nanocomposite exhibiting good photocurrent response from the visible range to NIR. Full article

We demonstrate the use of a novel, integrated THz system to obtain time-domain signals for spectroscopy in the 0.1–1.4 THz range. The system employs THz generation in a photomixing antenna excited by a broadband amplified spontaneous emission (ASE) light source and THz detection with a photoconductive antenna by coherent cross-correlation sampling. We benchmark the performance of our system against a state-of-the-art femtosecond-based THz time-domain spectroscopy system in terms of mapping and imaging of the sheet conductivity of large-area graphene grown by chemical vapor deposition (CVD) and transferred to a PET polymer substrate. We propose to integrate the algorithm for the extraction of the sheet conductivity with the data acquisition, thereby enabling true in-line monitoring capability of the system for integration in graphene production facilities. Full article

It is shown in this paper that a polymer, MA-PEG 1000-DGEBA (MP1D), exhibits antireflection, substrate-dependent photoluminescence (SDP), wide band-gap, and photoconduction characterization. MP1D was synthesized from maleic anhydride, polyethylene glycol 1000, and bisphenol-A diglycidyl ether. Self-assembled nanoparticles embedded in MP1D film and ranging from 2.5 to 31.6 nm are observed, which could be expected as scatterers to enhance light trapping and extraction. The size of the nanoparticle increases with the concentration of the MP1D solution. Besides solution concentration, the nanoparticle dimension could be modified by the chain length of polyethylene glycol in the polymer synthesis. The effects of solution concentration, annealing temperature, annealing period, and substrate on the photoluminescence (PL) of MP1D films are examined. Increasing solution concentration increases PL intensity. However, aggregation-caused quenching is explicit as the solution concentration exceeds 100 mM. PL intensity increases with annealing temperature, which could be attributed to crystallinity improvement. PL intensity increases with increasing the annealing period from 0.5 to 2 h. Nonetheless, as the annealing period exceeds 2 h, PL quenching is emerging, which could be due to aggregation. It is expected that MP1D could be a promising candidate for host materials and MP1D film could play a multifunctional role (antireflective and light-trapping functions) in optoelectronics. Full article

We present a plasmonic-enhanced dielectrophoretic (DEP) phenomenon to improve optical DEP performance of a floating electrode optoelectronic tweezers (FEOET) device, where aqueous droplets can be effectively manipulated on a light-patterned photoconductive surface immersed in an oil medium. To offer device simplicity and cost-effectiveness, recent studies have utilized a polymer-based photoconductive material such as titanium oxide phthalocyanine (TiOPc). However, the TiOPc has much poorer photoconductivity than that of semiconductors like amorphous silicon (a-Si), significantly limiting optical DEP applications. The study herein focuses on the FEOET device for which optical DEP performance can be greatly enhanced by utilizing plasmonic nanoparticles as light scattering elements to improve light absorption of the low-quality TiOPc. Numerical simulation studies of both plasmonic light scattering and electric field enhancement were conducted to verify wide-angle scattering light rays and an approximately twofold increase in electric field gradient with the presence of nanoparticles. Similarly, a spectrophotometric study conducted on the absorption spectrum of the TiOPc has shown light absorption improvement (nearly twofold) of the TiOPc layer. Additionally, droplet dynamics study experimentally demonstrated a light-actuated droplet speed of 1.90 mm/s, a more than 11-fold improvement due to plasmonic light scattering. This plasmonic-enhanced FEOET technology can considerably improve optical DEP capability even with poor-quality photoconductive materials, thus providing low-cost, easy-fabrication solutions for various droplet-based microfluidic applications. Full article

The optoelectronic properties of a new poly(2-ethyl-3-methylindole) (MPIn) are discussed in this paper. The absorption and photoluminescence spectra were studied. The electronic spectrum of MPIn showed a single absorption maximum at 269 nm that is characteristic of the entire series of polyindoles. The fluorescence spectra show that the emission peaks of the test sample are centered around 520 nm. The photoconductivity of thin film samples of MPIn polyindole was studied by measuring the current-voltage characteristics under ultraviolet radiation with a wavelength of 350 nm. Samples of phototransistors were obtained, where thin films of MPIn polyindole were used as a transport layer, and their characteristics were measured and analyzed. The value of the quantum efficiency and the values of the mobility of charge carriers in thin polyindole films were estimated. Full article

We have performed comparative numerical calculations using a multiple trapping (MT) formalism with an exponential and an aggregate two-exponential trap distributions for describing two mostly used experimental setups for studying the radiation-induced conductivity (RIC) and the time-of-flight (TOF) effects. Computations have been done for pulsed and long-time electron-beam irradiations in a small-signal regime. Predictions of these two approaches differ appreciably in both setups. The classical MT approach proved very popular in photoconductive polymers generally and in molecularly doped polymers in particular, while a newly proposed complex MT worked well in common polymers. It has been shown that the complex MT successfully accounts for the presence of inherent deep traps, which may or may not have an energy distribution. Full article

In the present work, we report the use of regioregular poly(3-hexyltiophene) polymer (RR-P3HT) as a potential light-activated material for sensing the chemical nerve agent simulant dimethyl methylphosphonate (DMMP). The electrical response of thick films of RR-P3HT, deposited by spray-coating method onto a porous laminate substrate at room temperature, to DMMP vapours was investigated. The studied material was activated by light-emitting diodes that emitted light of different wavelengths. The sensing properties of RR-P3HT are considerably enhanced upon exposure to blue and yellow light. However, excitation by the low wavelength light (blue) caused degeneration of the material, resulting in lowered stability. In the case of the yellow light, degeneration was much slower and the limit of detection was 0.4 ppm. The studied material exhibited high selectivity, as it did not respond to 6 ppm of acetone and methanol vapours. Full article

This paper proposes an effective approach to fabricate a blue phase liquid crystal (BPLC) microlens array based on a photoconductive film. Owing to the characteristics of photo-induced conducting polymer polyvinylcarbazole (PVK), in which conductivity depends on the irradiation of UV light, a progressive mask resulting in the variation of conductivity is adopted to produce the gradient distribution of the electric field. The reorientations of liquid crystals according to the gradient distribution of the electric field induce the variation of the refractive index. Thus, the incident light experiences the gradient distribution of the refractive index and results in the focusing phenomenon. The study investigates the dependence of lens performance on UV exposure time, the focal length of the lens, and focusing intensities with various incident polarizations. The BPLC microlens array exhibits advantages such as electrically tunability, polarization independence, and fast response time. Full article