Search Results (50)

The study presented an analysis of the behaviour of cellular structures under bending, produced using the PolyJet Matrix (PJM) additive manufacturing method with photopolymer resin. Structures with regular cell geometry were designed to achieve a balance between stiffness, weight reduction, and energy absorption capacity. The aim of this study was to investigate the influence of unit-cell topology (quasi-similar, spiral, hexagonal honeycomb, and their core–skin hybrid combinations) on the flexural properties and deformation mechanisms of PolyJet-printed photopolymer beams under three-point bending. Additionally, all cellular configurations were fully infiltrated with a low-modulus platinum-cure silicone to evaluate the effect of complete polymer–elastomer interpenetration on load-bearing capacity, stiffness, ductility, and energy absorption. All tests were performed according to bending standard on specimens fabricated using a Stratasys Objet Connex350 printer with RGD720 photopolymer at 16 µm layer thickness. The results showed that the dominant failure mechanism was local buckling and gradual collapse of the cell walls. Among the silicone-filled cellular beams, the QS-Silicone configuration exhibited the best overall flexural performance, achieving a mean peak load of 37.7 ± 4.2 N, mid-span deflection at peak load of 11.4 ± 1.1 mm, and absorbed energy to peak load of 0.43 ± 0.06 J. This hybrid core–skin design (quasi-similar core + spiral skin) provided the optimum compromise between load-bearing capacity and deformation capacity within the infiltrated series. In contrast, the fully dense solid reference reached a significantly higher peak load of 136.6 ± 10.2 N, but failed in a brittle manner at only ~3 mm deflection, characteristic of UV-cured rigid photopolymers. All open-cell silicone-filled lattices displayed pseudo-ductile behaviour with extended post-peak softening, enabled by large-scale elastic buckling and silicone deformation and progressive buckling of the thin photopolymer struts. The results provided a foundation for optimising the geometry and material composition of photopolymer–silicone hybrid structures for lightweight applications with controlled stiffness-to-weight ratios. Full article

A novel approach was developed in this work in which composite nanofiltration (NF) membranes were directly and efficiently fabricated with control of the membrane pore structure and surface morphology. The fabrication of mesoporous silicon-modified polysulfone blend membranes is achieved via a phase inversion method. The structural morphology, surface functional group analysis, elemental analysis, hydrophilicity, chargeability, and nitrogen pollutant (ammonia nitrogen, nitrate nitrogen, total nitrogen) rejection properties of the modified membranes were found to be dependent on the amount of mesoporous silicon incorporated. The combination of the mesoporous silicon framework layer can not only effectively improve the surface structure of the modified membrane with a narrow pore size distribution but also increase the rejection of nitrogen pollutants compared with pure NF membranes. The mesoporous material interlayer can absorb and store the aqueous amino solution to facilitate the subsequent interfacial polymerization as well as induce changes in the pore radius and surface structure. Compared with pure NF composite membranes, the modified blend membranes exhibit increased water permeation flux as high as 29.09 L m⁻² h⁻¹ at 0.2 MPa. The results show that the optimum doping amount of mesoporous silicon is in the range of 0.5–1.0%. Characterization studies demonstrated that the addition of mesoporous silicon leads to a decreased membrane pore size. Then the retention of nitrogen pollutants was enhanced because of a combination of hydrophilicity enhancement from the carboxylic and hydroxyl functional groups present in their surfaces leading to electrostatic repulsion between functional groups present in the membranes and the nitrogen pollutant molecules. Full article

Aiming at the lightweight design of a bridge-shed integration structure, this paper presents a three-layered absorbing system in which a part of the sand cushion is replaced by expanded polystyrene (EPS) geofoam and the reinforced concrete (RC) protective slab is arranged above the sand cushion to enhance the composite system’s safety. A three-dimensional Smoothed Particle Hydrodynamics–Finite Element Method (SPH-FEM) coupled numerical model is developed in LS-DYNA (Livermore Software Technology Corporation, Livermore, CA, USA, version R13.1.1), with its validity rigorously verified. The dynamic response of rockfall impacts on the shed slab with composite cushions of various thicknesses is analyzed by varying the thickness of sand and EPS materials. To optimize the cushion design, a specific energy dissipation ratio (SEDR), defined as the energy dissipation rate per unit mass (η/M), is introduced as a key performance metric. Furthermore, the complicated interactional mechanism between the rockfall and the optimum-thickness composite system is rationally interpreted, and the energy dissipation mechanism of the composite cushion is revealed. Using logistic regression, the ultimate stress state of the reactive powder concrete (RPC) slab is methodically analyzed, accounting for the speed and mass of the rockfall. The results are indicative of the fact that the composite cushion not only has less dead weight but also exhibits superior impact resistance compared to the 90 cm sand cushions; the impact resistance performance index SEDR of the three-layered absorbing system reaches 2.5, showing a remarkable 55% enhancement compared to the sand cushion (SEDR = 1.61). Additionally, both the sand cushion and the RC protective slab effectively dissipate most of the impact energy, while the EPS material experiences relatively little internal energy build-up in comparison. This feature overcomes the traditional vulnerability of EPS subjected to impact loads. One of the highlights of the present investigation is the development of an identification model specifically designed to accurately assess the stress state of RPC slabs under various rockfall impact conditions. Full article

In this study, a UVC photodetector (PD) was fabricated by incorporating CsI into a conventional double-cation perovskite (FAMAPbI₃) to enhance its stability. The device utilized a methylammonium iodide post-treatment solution to fabricate CsFAMAPbI₃ perovskite thin films, which functioned as the primary light-absorbing layer in an NIP structure composed of n-type SnO₂ and p-type spiro-OMeTAD. Perovskite films were fabricated and analyzed as a function of the Cs concentration to optimize the Cs content. The results demonstrated that Cs doping improved the crystallinity and phase stability of the films, leading to their enhanced electron mobility and photodetection performance. The UVC PD with an optimum Cs concentration exhibited a responsivity of 58.2 mA/W and a detectivity of 3.52 × 10¹⁴ Jones, representing an approximately 7% improvement over conventional structures. Full article

The mixture powders were designed by adding 0 wt.%~1.0 wt.% CeO₂ into the 2205 duplex stainless steel (DSS) powders. The 2205 DSS cladding layer was prepared on the surface of Q345 steel by plasma arc cladding technology. The effects of different CeO₂ contents on the macro-morphology, microstructure composition, and corrosion resistance of the cladding layer were studied. The action mechanism of CeO₂ in the cladding layer was also discussed. The results showed that the addition of CeO₂ modified the appearance and decreased the defect of the cladding layer. Also, the austenite grains were refined, and the austenite proportion was increased under the action of CeO₂. When the CeO₂ content was 0.5 wt.%, the appearance of the cladding layer was optimum; the austenite proportion in the upper cladding layer and the lower cladding layer reached up to 52.6% and 55.5%, respectively, and the crystal changed from columnar to equiaxed. CeO₂ decomposes into Ce element and O element under the action of the plasma arc, after which Ce element is easily absorbed at the grain boundary to reduce the surface tension and improve the fluidity of the liquid metal so as to modify the appearance of the cladding layer. Meanwhile, Ce element primarily reacts with O, S, Al, and Si elements to form low-melting-point oxygen sulfides and are then removed, which eliminates the defect of the cladding layer. Moreover, the high melting point of CeO₂ acts as heterogeneous nucleation sites during solidification, thus improving the value of nucleation rate/growth rate of the grain and promoting the transformation from ferrite to austenite. According to the electrochemical corrosion testing result, Ce element inhibited the enrichment of Cr element at grain boundaries and promoted the formation of Cr₂O₃, which improved the corrosion resistance of the 2205 DSS cladding layer. It was optimum with the CeO₂ content of 0.5 wt.%. Full article

Tandem solar cells have the potential to be more efficient than the Shockley–Queisser limit imposed on single junction cells. In this study, optical and electrical modeling based on experimental data were used to investigate the possibility of boosting the performance of kesterite/c-Si tandem solar cells by inserting an alternative nontoxic TiO₂ buffer layer into the kesterite top subcell. First, with SCAPS-1D simulation, we determined the data reported for the best kesterite (CZTS (Eg = 1.5 eV)) device in the experiments to be used as a simulation baseline. After obtaining metric parameters close to those reported, the influence on the optoelectronic characteristics of replacing CdS with a TiO₂ buffer layer was studied and analyzed. Different top subcell absorbers (CZTS0.8Se0.2 (Eg = 1.4 eV), CZTS (Eg = 1.5 eV), CZTS (Eg = 1.6 eV), and CZT0.6Ge0.4S (Eg = 1.7 eV)) with different thicknesses were investigated under AM1.5 illumination. Then, to achieve current matching conditions, the c-Si bottom subcell, with an efficiency at the level of commercially available subcells (19%), was simulated using various top subcells transmitting light calculated using the transfer matrix method (TMM) for optical modeling. Adding TiO₂ significantly enhanced the electrical and optical performance of the kesterite top subcell due to the decrease in parasitic light absorption and heterojunction interface recombination. The best tandem device with a TiO₂ buffer layer for the top subcell with an optimum bandgap equal to 1.7 eV (CZT0.6Ge0.4S4) and a thickness of 0.8 µm achieved an efficiency of approximately 20%. These findings revealed that using a TiO₂ buffer layer is a promising way to improve the performance of kesterite/Si tandem solar cells in the future. However, important optical and electrical breakthroughs are needed to make kesterite materials viable for tandem applications. Full article

A sequence of dye-sensitized solar cells is proposed, utilizing TiO₂@Zn/Al-layered double hydroxide (LDH) as their starting materials, in which Ruthenizer N719 was used as a photon absorber. The anticipated system was turned into sheet-like TiO₂@mixed metal oxide (MMO) via post-processing treatment. The crystal quality indicated a relation to power conversion efficiency (PCE); this was combined with a comparable morphology profile. In detail, the optimum DSSC device exhibited average sheet-like thickness and a dye loading amount of 43.11 nm and 4.28 $\times {10}^{-3}$ mM/cm⁻², respectively. Concurrently, a considerable PCE enhancement of the optimum DSSC device (TiO₂@MMO-550°) was attained compared to pristine MMO (0.91%), which could be due to boosted electron transfer efficiency. Of the fabricated devices, DSSC fabricated at 550° exhibited the highest PCE (1.91%), with a 35.6% enhancement compared to that obtained at 450°, as a result of its increased open-circuit voltage (3.29 mA/cm²) and short-circuit current (0.81 V). The proposed work delivers an enhanced efficiency as compared to similar geometries. Full article

In this paper, a novel tubular solar air heater is introduced. In this air heater, the hot boundary layer is drawn into the absorber tube and can provide thermal energy at moderate temperatures. Several different cases were simulated and a correlation was proposed to predict the collector’s effectiveness as a function Rayleigh number and Reynolds number. An equation was derived to find the effectiveness of this collector. Finally, a real case was studied with non-uniform solar flux distribution, as well as radiation heat loss. Good agreement was found between the results and those derived by the proposed analytical method. For different suction values, the first-law and the second-law efficiencies were calculated. Based on the exergy analysis, exergy destruction in absorption is the dominant factor that is unavoidable in low-temperature collectors. It was shown that there is an optimum suction value at which the second-law efficiency is maximized. At the optimum point, temperature rise can reach 54 K, which is hardly possible with a flat plate collector. Based on the exergy analysis, the relation between tube wall temperature and air outlet temperature in their dimensionless forms at the optimum working condition was derived, and it was shown that effectiveness at the optimum working condition is around 0.5. This means that the air temperature rise shall be half of the temperature difference between collector wall and the ambient temperatures. A high outlet temperature besides the low cost of construction and maintenance are the main advantages of this air heater. With such a high temperature rise, this type of collector can increase the use of solar energy in domestic applications. Full article

In this paper, coal measure kaolin after flotation decarburization was made into an adsorbent by ball milling and acid modification to absorb methylene blue in water, achieving the treatment of waste with waste. The objective of this paper is to expand the application of coal measure kaolin, reduce its stock, and lower the raw material cost of adsorbents while treating wastewater containing methylene blue. The optimum milling time, acid boiling conditions, and adsorption conditions were investigated. Furthermore, the adsorption mechanism was investigated by kinetic calculation. The results show that the optimum milling time is 7 h. Relatively good acid modification conditions include a boiling temperature of 100 °C, a stirring time of 135 min, a stirring speed of 1000 r·min⁻¹, and a concentration of hydrochloric acid of 8 mol·L⁻¹. When 0.05 g of flotation kaolin adsorbent was used to adsorb the solution with pH 12 and a methylene blue concentration of 100 mg·L⁻¹, the optimal adsorption conditions were a 38.05 °C adsorption temperature, a 160 r·min⁻¹ stirring speed, and a 31.02 min stirring time. Under these optimal conditions, the adsorption quantity reached 39.92 mg·g⁻¹. The adsorption process involves physical adsorption and spontaneous adsorption. The adsorption type is known as the quasi-second-order adsorption kinetic model. The adsorption form is heterogeneous adsorption in which a monolayer and a multi-molecular layer coexist. Full article

The main objective of this study was to determine the variation in the properties of cadmium telluride (CdTe) thin films deposited on a p-type Si substrate by the radio frequency magnetron sputtering technique at four different working powers (70 W, 80 W, 90 W, and 100 W). The substrate temperature, working pressure, and deposition time during the deposition process were kept constant at 220 °C, 0.46 Pa, and 30 min, respectively. To study the structural, morphological, and optical properties of the CdTe films grown under the mentioned experimental conditions, X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and optical spectroscopy were used. For a better analysis of the films’ structural and optical properties, a group of films were deposited onto optical glass substrates under similar deposition conditions. The electrical characterisation of Ag/CdTe/Al “sandwich” structures was also performed using current–voltage characteristics in the dark at different temperatures. The electrical measurements allowed the identification of charge transport mechanisms through the structure. New relevant information released by the present study points towards 90 W RF power as the optimum for obtaining a high crystallinity of ~1 μm nanostructured thin films deposited onto p-Si and optical glass substrates with optical and electrical properties that are suitable for use as absorber layers. The obtained high-quality CdTe nanostructured thin films are perfectly suitable for use as absorbers in CdTe thin-film photovoltaic cells. Full article

Nitrogen (N) can enhance the biomass and feeding quality of forage crops and advance the growth of the herbivorous livestock industry. Investigating the N fertilizer dynamics in the soil–crop–livestock system is important for resource-use efficiency and environmental safety. By using the ¹⁵N-labeled technology and the in vitro incubation technique, an experiment was conducted in the North China Plain (NCP) in 2015–2016 to quantify the migration and distribution of N fertilizer in the soil–forage triticale (X Triticosecale Wittmack)–dairy cow system. The results showed that 34.1–37.3% of the applied N fertilizer was absorbed by forage triticale, in which 35.9–39.6% N accumulated in the stems and 60.4–64.1% accumulated in the leaves. In addition, 36.3–39.1% of the applied N fertilizer remained in the 0–100 cm soil layer, in which 81.8–91.3% was distributed in the 0–40 cm soil layer. The remaining 24.6–26.8% of the applied N fertilizer was lost in various ways and 28.1–31.3% of the N fertilizer could be utilized by dairy cows. When N fertilizer was applied between 0–225 kg N ha⁻¹, the increased application of N fertilizer improved the biomass yield from 14.0 to 17.5 t ha⁻¹ and enhanced the N content of the forage triticale from 1.3% to 1.4%; however, it did not significantly affect the distribution rate of N fertilizer in the soil–forage triticale–dairy cow system. The optimum N fertilizer application rate for forage triticale is less than 225 kg N ha^–1 to maintain high-efficient N use in the soil–crop–livestock system and reduce the environmental risks in the NCP. Our results quantified the N fertilizer dynamics in the soil–forage triticale–dairy cow system and provided a significant reference for guiding rational strategies of forage triticale cultivation. Full article

The increasing demand for energy and electricity and the depletion of fossil fuels are global problems. In recent years, dye-sensitized solar cell (DSSC) technologies have gained notoriety for their application in solar energy. DSSCs are considered a promising alternative renewable energy source to both inorganic and organic photovoltaic (PV) cells. Many types of dyes are being investigated to enhance the light-harvesting properties of DSSCs, but the actual realization of these absorbers in cell structure requires optimum parameters. The main aim of this study was to simulate proposed zinc phthalocyanine (ZnPC)-based structures to validate their design, assess their performance for commercial implementation, and optimize the cell parameters for optimum efficiency. To that end, Scaps-1D was employed to evaluate the performance of DSSCs to determine their optimum parameters. We found that ZnPC and isopropoxy ZnPC molecules outperform others molecules because of better optoelectronic properties. Several other parametric effects, such as photoactive layer thicknesses, doping densities, trap densities, and charge carrier mobilities, were also evaluated to observe their impact on device performance. The results show that moderate thickness, low defect density, moderate doping, and charge carrier mobility are favorable for better device performance due to low recombination losses, electrical losses, and better transport of charge carriers. The utmost power conversion efficiency values found for ZnPC- and ZnPC: PC70BM-based DSSCs after optimization were 9.50% and 9.81%. This paper also suggests a practical method for efficiently using DSSC cells by modifying factors that are significantly reliant on DSSC performance and output. Full article

This is a comprehensive research endeavor focused on enhancing the efficiency of the proposed solar cell design. The integration of the simulation techniques, judicious material selection, and meticulous performance metrics showcase a methodical approach toward creating a solar cell capable of achieving high efficiency across a wide spectrum of light in the AM 1.5 G1 sun solar cell illumination spectrum. Having said this, many researchers are still working on the efficiency potential—based on external radiative efficiency (ERE), open-circuit voltage loss, and fill factor loss—of high-efficiency solar cells. The solar cell is built on aluminum-doped zinc oxide (ZnO) as a transparent conductive oxide layer; aluminum nitride (AlN) as the window layer (emitter); an SWCNT layer as the absorber layer; gallium phosphide (GaP) as the contact layer; and silicon as the substrate. The proposed solar cell transmission, reflection, and absorption relative to the variations in wavelength band spectrum are studied. The conduction and valence band energy diagrams of the solar cell design structure are simulated against the layer thickness variations for the suggested solar cell structure. Short-circuit current density and maximum power variations are clarified versus the bias voltage. Light current density is simulated versus the bias voltage (J/V characteristics curve) of the suggested solar cell design structure. The carrier generation–recombination rate is also simulated by the COMSOL simulation program versus the layer thickness of the suggested solar cell structure. The solar cell circuit design has a fill factor (FF) value of 74.31% and a power conversion efficiency value of 29.91%. Full article

The simulated device structures of ITO/ZnO/Perovskite absorber layers (PAL)/Spiro-OMeTAD/Au with distinct absorbers were modeled and investigated using solar cell capacitance simulator (SCAPS-1D) simulating software (version 3.8). The primary objective is to enhance the thermal stability of the solar device. As the absorber thickness and temperature impact PV performance parameters, thus main aim of this work is to determine the optimum thickness of PAL as well as the temperature affectability on the PV performance of the cells. It was also observed that the maximum PV parameters (among the cells under consideration), viz. 29% PCE, are achieved with the formamidinium tin iodide (FASnI₃) at the thickness of 600 nm. Similarly, the temperature of 300 K shows a much-improved efficiency offering nearly 29%. Further, the external quantum efficiency (EQE) and J-V also confirm the determent of the more stable, lead-free, FASnI₃-based device, which can provide an effective way to develop highly efficient, low-cost solar cell devices. Full article

Considering photocatalytic degradation technology has recently attracted great attention for dyeing wastewater treatment, the polyacrylonitrile (PAN) nanofibrous membrane coated with the TA/Fe^III complexes was proposed as a novel photocatalyst in this work. The successful self-assembly of TA/Fe^III complexes on the PAN nanofibrous membrane after layer-by-layer deposition of TA and Fe^III was confirmed by the analyses of chemical structure, morphology, and hydrophilicity. With the number of coating cycles, more TA/Fe^III complexes coated on the PAN nanofibrous membrane, which contributed to the excellent photocatalytic activity. Whereas, when the coating cycles reached seven, the photocatalytic performance of the modified PAN nanofibrous membrane deteriorated due to the serious aggregation of TA/Fe^III complexes. Under optimum five coating cycles, owing to its great light absorbance capability, the modified PAN nanofibrous membrane achieved 98% degradation efficiency of RhB after 360 min illumination. This work would offer a promising high-performance photocatalyst for dyeing wastewater treatment. Full article